INSTRUCTION
BOOKLET
®
Cuisinart®
WCH-1500
Countertop Filtration System
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
9. Indicator Lights
CONTENTS
Red/blue LEDs light up when water has
reached hot/cold temperatures. Green LED
lights up when unit is in "Energy Saver"
mode (hot water is Off).
Important Safeguards. . . . . . . . . . . . . . 2
Special Cord Set Instructions . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . 3
Parts and Features. . . . . . . . . . . . . . . . 3
Unpacking & Placement. . . . . . . . . . . . 4
Water Filter Setup . . . . . . . . . . . . . . . . 4
Water Dispenser Setup . . . . . . . . . . .4-5
Operating Instructions . . . . . . . . . . . . . 5
Replacing Water Filter . . . . . . . . . . . . . 5
Tips and Hints . . . . . . . . . . . . . . . . . .5-6
Cleaning and Care . . . . . . . . . . . . . . . . 6
Troubleshooting . . . . . . . . . . . . . . . . .6-7
Storing the Unit . . . . . . . . . . . . . . . . . . 8
Technical Specifications . . . . . . . . . . . 8
Performance Data Sheet . . . . . . . . . . . 9
California Certification . . . . . . . . . . . . 10
For Purchases Made in Iowa . . . . . . 10
Warranty . . . . . . . . . . . . . . . . . . . . . . . 11
10. Spigots
11. Brushed Stainless Steel Base
12. Internal Water Tanks (not shown)
Hot and cold tanks – approx. ½ gallon
total capacity.
13. Energy Saver Switch (not shown)
Turn off your heater when hot water is not
needed to reduce the system's energy
usage by more than 50%.
14. Drainage Plugs (not shown)
Two removable plastic plugs are located
on bottom of unit.
15. Replacement Water Filter
(Model GF-80)
The Cuisinart® water filter has an optimum
filter life of 3 months.
INTRODUCTION
Pour yourself a glass of fresher, cleaner,
filtered water for a refreshing drink without
opening the refrigerator or a bottle.
®
1
2
3
Your
Countertop Filtration
System is Cuisinart at its most convenient.
Drink healthy!
PARTS AND FEATURES
4
5
1. 12-Week Filter Timer
Lets you know when to change your
water filter.
6
7
8
9
10
2. Cover
Flip-top lid for easy filling.
3. Upper Water Tank
Holds approx. ½ gallon of unfiltered water.
11
12
4. Lower Water Tank
Holds approx. 1 gallon of filtered water.
5. On/Off Power Button
Press to power On. This will activate the
chilling and heating functions.
13
6. Hot Water Button with Child Lock
Push safety lock up, then press to dispense
hot water.
14
15
7. Room Water Button
Press to dispense room temperature water.
8. Cold Water Button
Press to dispense chilled water.
ꢁ
2. Remove the filter timer from the lid by flipping
the lid over and pressing on the plastic tab.
UNPACKING & PLACEMENT
®
1. Remove your Cuisinart®
3. Wash both tanks and plastic lid in mild, soapy
water, and rinse. Replace the filter timer.
Countertop Filtration System carefully from
the box.
4. Lift the filter from the bowl and allow water to
drain.
2. Position the unit on a stable flat surface, close
to a main power outlet. Avoid direct sunlight
and keep out of the reach of children.
NOTE: The filter's loose carbon dust may
slightly darken water while soaking.
3. Allow at least 3 inches of space around
the sides and rear of the unit for proper air
circulation.
5. With the Cuisinart® logo
facing up, insert the water
filter into the upper water
tank and push firmly into
place.
4. Remove filter from upper tank and carefully
follow the SETUP instructions below. You will
need a large bowl, a pitcher (or another type
of container), and a glass.
6. Place the upper tank on a
pitcher (or another type of
container) and fill with cold
tap water. Allow to drain for
5 minutes to flush out any
remaining carbon dust, then
pour out remaining water.
NOTE: Do not plug in unit until ALL steps of
SETUP are complete.
WATER FILTER SETUP
NOTE: For optimum filtering and flow rates,
the water filter must be prepared and installed
exactly as follows:
WATER DISPENSER
SETUP
Preparing the Water Filter
1. Remove the filter from its packaging.
NOTE: Use only cold tap water to fill the unit.
NOTE: The filter may contain a small amount
of loose carbon dust. It may also appear moist,
have a faint smell of plastic or a slight yellowish
tint – these are all normal. DO
Filling the Upper and Lower Tanks
1. Place the upper tank onto the lower tank and
cover with the lid.
NOT wash filter with soap or
Lid
water.
Upper
2. Place water filter in
water tank
empty bowl sideways
(see image). Pressing it
Lower
firmly to the bottom of the bowl, and being
careful not to pour water directly onto the
filter, slowly add enough cold water to fully
submerge and cover the filter by at least 1
inch. (You should see bubbles escaping the
filter.)
water tank
2. Place assembled tanks on base. NOTE: The
vertical groove on the upper tank must face
the back of the unit.
3. Continue to hold filter
under water for at least 30
seconds.
3. Carefully lift the flip top lid and add cold
water to the FILL line. NOTE: This is a gravity
fill system. To increase the filtering flow rate,
continue adding water to the FILL line of the
upper tank until tanks are completely full.
4. Release the filter and
let it soak at least 15 minutes. NOTE:
While soaking, the filter should be partially
submerged and may tilt to one side.
4. During the initial setup, allow 30–40 minutes
for water to filter into and completely fill upper
and lower tanks.
Installing the Prepared Water Filter
1. While the filter is soaking, remove the lid,
upper water tank and lower water tank.
ꢂ
Filling the Internal Tanks
NOTE: Energy Saver switch must be in the
Upper
Tank
Off position for water to heat.
NOTE: Upper and lower
tanks must be completely
full before proceeding.
4. After about 1 hour and 20 minutes, the BLUE
cold water indicator will light up, signaling
water is chilled.
Lower
Tank
1. Place a glass under the
right spigot and press
and continue to hold
the COLD button until
water flow becomes
steady (may take up
to 3 minutes).
NOTE: On subsequent fill-ups, unit should take
less than 10 minutes to heat and 30 minutes
to chill.
5. Press and hold each button to ensure all air
has been purged from the unit so water flow
is steady.
2. Repeat process with ROOM button, and then
with the HOT button until all flow steadily.
Initiating Energy Saver Mode
You can turn off the heater used to heat the
water in the hot tank to reduce the system's
energy usage by more than 50%. While in
Energy Saver mode, you can still dispense water
from your hot tank; however, it will not
be heated.
NOTE: When filling hot and cold internal tanks,
the water level in the lower tank will drop and
you will hear the filling process taking place.
Setting the Filter Timer
The filter timer, located on the lid of the unit, lets
you know when to change your water filter. Each
filter will last for 3 months.
NOTE: We recommend you power your unit off
when only room temperature filtered water
is needed.
1. Once unit is set up and all water tanks are full,
peel off the “Filtering” sticker from the filter
timer screen.
1. Put the Energy Saver switch in its On position.
2. The green LED will light up, indicating your
unit is in Energy Saver mode.
2. Press and hold the Start button until
FILTERING is displayed (approx. 5 seconds).
3. Because your unit is in Energy Saver mode
and your hot water heater is disabled, the red
LED hot water indicator light will turn off when
the temperature of the hot water decreases
(this can take up to 2 hours).
3. In 12 weeks, the word REPLACE will appear.
For best results, we recommend inserting a
new Cuisinart® Water Filter immediately.
4. You may turn off the timer and display by
pressing the Start button for 5 seconds.
Once you replace the filter, reset the timer by
pressing the Start button for 3 seconds.
4. To resume your hot water, simply put the
Energy Saver switch in its Off position. After
about 15 minutes, the red LED hot water
indicator will light up, signaling hot water is
ready to dispense.
NOTE: You may reset the timer at any time by
pressing and holding the Start button for
3 seconds.
NOTE: If your unit has been in Energy Saver
mode for longer than a week, we recommend
you flush out your hot water tank by dispensing
and disposing of a full glass of water from the
left spigot before enjoying your first glass of hot
water.
OPERATING INSTRUCTIONS
Once set up is completed, tanks are filled and
water is flowing steadily, your unit is ready to use!
1. Close the lid and plug unit into outlet.
2. Press the On/Off power switch on the control REPLACING WATER FILTER
panel to turn on. The BLUE light around the
power switch indicates the unit is on and
cooling and heating functions are activated.
Replacement filters may be purchased at most
your filter, follow “Water Filter Setup” on page 4.
3. After about 15 minutes, the RED hot water
indicator will light up, signaling hot water is
ready to dispense.
TIPS AND HINTS
• Drinking 4 to 8 glasses of water each day is
healthy! Your countertop chiller makes it easy.
ꢃ
• Regular use of cleaner, filtered water in your
automatic coffeemaker means less frequent
decalcification treatments.
CLEANING AND CARE
CAUTION: To prevent personal injury
or electric shock, always unplug your
Cuisinart®
® Countertop Filtration
• Use filtered water in your iron to reduce
mineral build-up.
System from outlet before cleaning. Do not
immerse base in water or other liquid.
• Treat your pets to cleaner, filtered water.
1. Turn the unit off and unplug it from outlet.
2. Remove the filter and place it in a bowl.
• Cleaner, filtered water makes tea and instant
soup or coffee taste better.
• Keeping the upper tank full helps increase
the filtering process as well as the flow rate
of water from spigots.
3. Lift upper water tank and let it drain into
lower tank, and set it aside. Then lift lower
tank off base and empty. Careful, a full tank
can be very heavy!
• Proper setup of the filter (as instructed
on page 4) will maximize the reduction of
contaminants and optimize taste of water.
4. Clean the water tanks and the cover with
warm soapy water. NOTE: Remove filter
timer before washing lid. Filter timer is not
immersible.
• You may notice some condensation and water
droplets on the lid and tanks of your unit.
This is normal due to the heating and cooling
system.
5. The base is not immersible. Simply wipe it
clean with a damp cloth.
6. Dry thoroughly when clean.
TROUBLESHOOTING
Symptom
Possible Cause
Solution
On/Off Power but-
ton does not light
up.
Unit might not be plugged
into outlet.
Check the wall outlet for power. Make sure the
outlet is not controlled by a wall switch.
It takes longer than
45 minutes for
the water to pass
through the filter.
Place filter in an empty bowl, then fill with
water, making sure it is fully submerged.
Resoak it for 10–15 minutes, or until no
more bubbles are observed.
Some air is still in the filter.
Review “Filling the Internal Tanks” on page 5
to be sure it was done correctly. Make sure the
lower water tank is full. Continue to press and
hold push buttons until water flow is steady. If
unit still won’t dispense water or flow does not
become steady, contact Customer Service.
Unit does not dis-
pense water when
buttons are pushed.
Internal water tanks are
not completely filled with
water.
Water continues
flowing from spigot
after push button is
released.
Remove water tanks from the base. Continue
pressing button until it no longer sticks.
Push button is stuck.
1. Make sure unit is plugged into outlet.
2. Make sure air has been purged from
internal tanks, as stated on page 5.
3. If there is water in the tanks, it will take
about 10 minutes for the water to heat.
1. Power is not on.
2. There is no water in
tanks.
HOT water LED
does not light up.
ꢄ
TROUBLESHOOTING
Symptom
Possible Cause
Solution
1. Make sure unit is plugged into outlet.
2. Make sure air has been purged from inter-
nal tanks, as stated on page 5.
3. If there is water in the tanks, it will take
about 80 minutes for the water to chill the
first time. It takes only about 30 minutes for
subsequent fill-ups.
1. Power is not on.
2. There is no water in
tanks.
COLD water LED
does not light up.
COLD water LED
light turns off even
though cold water is
not dispensed.
Large amount of room
temperature water was
dispensed.
Allow up to 30 minutes for water to chill and
LED light will turn on.
Energy Saver mode
LED does not light
up.
1. Power is not on.
2. Energy Saver is in Off
position
1. Make sure unit is plugged into outlet.
2. Make sure Energy Saver switch is in its On
position.
Heater is still work-
ing and hot water
is still available in
Energy Saver mode.
Contact Customer Service.
Filter timer does not
show “Filtering” or
“Replace.”
Contact Customer Service for replacement
filter timer.
Battery is dead.
1. Water tanks are not
properly seated on
base.
2. Drainage plugs are not
fully engaged.
1. Make sure water tanks are seated
properly on the base.
2. Ensure that drainage plugs are correctly
installed on the bottom of the base.
Leakage on the
countertop.
Water leaks from the
top cover.
Drain excess water from tanks by pressing
push buttons.
Water tanks are overfilled.
ROOM temperature
water is warm.
Allow up to 30 minutes for cold water to chill
and blue LED light to turn on.
HOT temperature
water is not hot.
Energy Saver is in On
position.
Make sure Energy Saver is in its Off position.
ꢅ
Bottom of unit
STORING THE UNIT
1. Turn the unit off and unplug it from outlet.
2. Remove empty water tanks, filter and cover.
3. Allow hot water to cool, then bring base to sink.
Drainage
Plugs
4. Drain internal reservoir by tilting unit slightly and removing the
2 plastic drainage plugs from bottom of unit. Plugs are tightly
inserted and must be gently, but firmly, worked to remove.
5. When water has completely drained, replace plugs, tanks,
filter and cover.
6. Your Cuisinart®
® Countertop Filtration System is ready to store.
TECHNICAL SPECIFICATIONS
®
Unit: WCH-1500
1 Cuisinart®
Countertop Filtration System
1 Cuisinart® Water Filter
System Capacity
up to 3 months/ 48 gallons/ 181 liters
104°F (40°C)
Maximum Input Temperature
Minimum Input Temperature
Maximum Output Temperature
Minimum Output Temperature
Rated Service Flow
34°F (1°C)
194°F (90°C)
44°F (7°C)
6 gallons / 22.7 liters per day
(may vary according to water conditions)
Electrical Requirements
AC~120V 60Hz 3.7A 450W
System Tested and Certified by WQA against NSF/ANSI Standard 53
for the reduction of Lead, Benzene, Cadmium, Copper, Mercury,
Tetrachloroethylene, Toluene, and Standard 42 for the reduction of
Chlorine Taste and Odor.
See Performance Data Sheet for specific test conditions and results.
Claims are calculated based on WQA accepted practice of average percent reduction. The
contaminants or other substances removed or reduced by this water treatment device are not
necessarily in all users’ water. Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system. Individuals requiring
water of specific microbiological purity should consult their physician.
The Cuisinart®
® Countertop Filtration System processes approximately 48 gallons/
181 liters. When the Cuisinart® Water Filter (GF-80) exceeds filtering capacity, replacement is
essential for the product to perform as represented. In the United States, replacement filters cost
generally $19.99 per filter. Replacement filters may be purchased at most retail outlets. The
performance of the filter may vary based on local water conditions.
Hot water should not be used with the Cuisinart® Water Filter (GF-80) as it will affect the filter’s
performance.
Refer to the Operating Instructions and Cleaning and Care for general unit operation and
maintenance requirements. Testing was performed under standard laboratory conditions;
actual performance may vary.
ꢆ
PERFORMANCE DATA SHEET
PERFORMANCE DATA SHEET FOR MODELS WCH-1000 AND WCH-1500
CONTAMINANT REMOVAL DATA IMPORTANT NOTICE:
Read this Performance Data Sheet and compare the capabilities of this unit with your actual
water treatment needs. It is recommended that, before purchasing a water treatment unit, you
have your water supply tested to determine your actual water treatment needs.
Performance testing conducted by WQA. These systems have been tested according to NSF/
ANSI Standard 53 and 42 for reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or
equal to the permissible limit for the water leaving the system, as specified in NSF/ANSI Standard
53 and Standard 42.
Testing was performed under standard laboratory conditions; actual performance may vary.
Removal
Removal
Action Level
Hardness
Temp
Inlet
Max.
Influent
Challenge
Concentration
(mg/L)
Filter
Effluent
Max.
Influent
Water Avg.
(mg/L)
Percent
Reduction
(%)
Permissible
Product Water
Concentration
(mg/L)
Testing
Compart.
(°C)
CaCO3
(mg/L)
Reduction
Requirement
Substance
PH
(mg/L)
NSF/ANSI Standard 42-Aesthetic Effects
Chlorine Taste and
Odor Reduction
2.0
2.0+/-10%
N/A
97.5%
N.A.
N.A.
20
7.53
>50
NSF/ANSI Standard 53-Health Effects
Copper pH 6.5
Copper pH 8.5
Mercury pH 6.5
Mercury pH 8.5
3.15
3.10
.006
.006
3.0+/-10%
3.0+/-10%
.87
1.0
85.0%
85.4%
92.8%
89.9%
1.3
1.3
16
120
22
20
19
19
20
6.42
8.42
6.45
8.55
N/A
N/A
N/A
N/A
0.006+/-10%
0.006+/-10%
.0009
.001
0.002
0.002
140
Cadmium pH 6.5
.029
0.03+/-10%
.002
96.6%
0.005
18
20
6.59
N/A
Cadmium pH 8.5
Benzene
.03
.015
2.9
0.03+/-10%
0.015+/-10%
3.0+/-10%
.004
.003
.770
92.5%
84.1%
89.8%
0.005
0.005
1
120
130
320
20
20
20
8.44
7.58
7.54
N/A
N/A
N/A
Toluene
Tetrachloroethylene
Lead pH 8.5
.014
.149
.154
0.015+/-10%
.15+/-10%
.15+/-10%
.003
.007
.004
92.5%
95.4%
98.7%
0.005
.010
.010
340
98
21
21
19
7.56
8.5
N/A
N/A
N/A
Lead pH 6.5
18
6.5
ꢇ
PURCHASES MADE IN IOWA
For purchases made in Iowa:
This form must be signed and dated by the buyer and seller prior to consummation of this sale.
This form should be retained on file by the seller for a minimum of two years.
BUYER:
SELLER:
Name
Name
Address
City
Address
City
State
Zip
State
Zip
Signature
Date
Signature
Date
10
This warranty expressly excludes any defects or
damages caused by accessories, replacement
parts, or repair service other than those that have
been authorized by Cuisinart.
WARRANTY
LIMITED THREE-YEAR WARRANTY
This warranty is available to consumers only.
You are a consumer if you own a Cuisinart®
Countertop Filtration System that was
This warranty does not cover any damage caused
by accident, misuse, shipment or other ordinary
household use.
purchased at retail for personal, family or household
use. Except as otherwise required under applicable
law, this warranty is not available to retailers or other
commercial purchasers or owners.
This warranty excludes all incidental or
consequential damages. Some states do not allow
the exclusion or limitation of these damages, so
these exclusions may not apply to you.
We warrant that your Cuisinart®
CALIFORNIA RESIDENTS ONLY
Countertop Filtration System will be free of defects
in materials and workmanship under normal home
use for 3 years from the date of original purchase.
California law provides that for In-Warranty Service,
California residents have the option of returning a
nonconforming product (A) to the store where it was
purchased or (B) to another retail store which sells
Cuisinart® products of the same type.
We suggest you complete and return the enclosed
product registration card promptly to facilitate
verification of the date of original purchase.
However, return of the product registration card
does not eliminate the need for the consumer to
maintain the original proof of purchase in order to
obtain the warranty benefits. In the event that you
do not have proof of purchase date, the purchase
date for purposes of this warranty will be the date of
manufacture.
The retail store shall then, at its discretion, either
repair the product, refer the consumer to an
independent repair facility, replace the product, or
refund the purchase price less the amount directly
attributable to the consumer’s prior usage of the
product. If the above two options do not result in
the appropriate relief to the consumer, the consumer
may then take the product to an independent repair
facility if service or repair can be economically
accomplished. Cuisinart and not the consumer
will be responsible for the reasonable cost of
such service, repair, replacement, or refund for
nonconforming products under warranty.
If your Cuisinart®
Countertop Filtration
System should prove to be defective within the
warranty period, we will repair it, or if we think
necessary, replace it.
To obtain warranty service, simply call our toll-free
number 1-800-726-0190 for additional information
from our Customer Service Representatives, or send
the defective product to Customer Service at:
California residents may also, according to their
preference, return nonconforming products directly
to Cuisinart for repair, or if necessary, replacement,
by calling our Consumer Service Center toll-free at
1-800-726-0190.
Cuisinart
150 Milford Road
East Windsor, NJ 08520.
Cuisinart will be responsible for the cost of the
repair, replacement, and shipping and handling for
such products under warranty.
BEFORE RETURNING YOUR CUISINART®
PRODUCT
To facilitate the speed and accuracy of your return,
please enclose $10.00 for shipping and handling of
the product.
Please pay by check or money order (California
residents need only supply proof of purchase
and should call 1-800-726-0190 for shipping
instructions).
If you are experiencing problems with your
Cuisinart® product, we suggest that you call our
Cuisinart® Service Center at 1-800-726-0190
before returning the product to be serviced. If
servicing is needed, a Representative can confirm
whether the product is under warranty and direct
you to the nearest service location.
NOTE: For added protection and secure handling
of any Cuisinart® product that is being returned, we
recommend you use a traceable, insured delivery
service. Cuisinart cannot be held responsible for
in-transit damage or for packages that are not
delivered to us. Lost and/or damaged products
are not covered under warranty. Please be sure to
include your return address, daytime phone number,
description of the product defect, product model
number (located on bottom of product), original date
of purchase, and any other information pertinent to
the product’s return.
Important: If the nonconforming product is to be
serviced by someone other than Cuisinart’s
Authorized Service Center, please remind the
servicer to call our Consumer Service Center at
1-800-726-0190 to ensure that the problem is
properly diagnosed, the product is serviced with
the correct parts, and the product is still under
warranty.
Your Cuisinart®
Countertop Filtration
System has been manufactured to the strictest
specifications and has been designed for use with
the authorized accessories and replacement parts.
11
Coffeemakers
Food
Processors
Toasters
Rice Cookers
Cookware
Grills
Cuisinart offers an extensive assortment of top quality products to make life in the
kitchen easier than ever. Try some of our other countertop appliances and
cookware, and Savor the Good Life®.
©ꢀ00ꢇ Conair Corporation
Cuisinart® is a registered
trademark of the
Conair Corporation
Cuisinart
1ꢃ0 Milford Road
East Windsor, NJ 0ꢆꢃꢀ0
1-ꢆ00-ꢅꢀꢄ-01ꢇ0
Printed in China
Any trademarks or service marks of third parties
referred to herein are the trademarks or service
marks of their respective owners.
0ꢇCE1ꢁꢇꢁꢂ
IB-8896A
|