C
Specifications
SH 5500 Series
Heavy-Duty Walkie
Straddle Stacker
SH 5500
Series
Specifications
SH 5500 Series
1
2
3
4
5
6
7
8
9
Manufacturer
Model
Crown Equipment Corporation
SH 5520-40
See Chart
24
SH 5540-40
See Chart
24
Load Capacity
Load Center
Power
lb
in
Electric
24 Volts
Stacker
Poly/Vulkolan
4/1x
24 Volts
Stacker
Poly/Vulkolan
4/1x
Operator Type
Tire Type
Walkie
Load/Drive
Wheels (x=driven) Load/Drive
Lifting Height
in
in
See Chart
36.8
See Chart
43.3
13 Head Length*
14 Wheelbase
15 Turning Radius
16 Inside Straddle
17 Forks
in
51.4
57.9
in
60.9
67.4
in
34 - 50 inches in 2" increments
Standard LxWxT
Optional Lengths
Empty/Loaded
Empty/Loaded
in
36 x 4 x 1.75
30, 39, 42, 45, 48, 54, 60
3.7 / 3.4
in
18 Travel Speeds
19 Lift Speeds
mph
fpm
fpm
%
48.4 / 29.5
20 Lowering Speeds Empty/Loaded
21 Grade Clearance
50 / 50
9
8
22 Battery
Min Weight/Max Amp
Max Battery Size WxLxH
510 / 300
975 / 660
6.62 x 34.37 x 24.8
13.12 x 31.10 x 24.8
* Add 2.1" for Side Shift
Mast Type
TL – Limited Free Lift
TT – Triple Telescopic
9
3
Lifting Height
Load Capacity
in
lb
lb
in
in
in
in
lb
lb
127.5
150.5
4000
4000
6
156
192
na
SH 5520-40
SH 5540-40
4000
4000
6
4000
4000
52.6
75
3000
52.6
89
10 Free Lift w/o LBR
11 Collapsed Height
12 Extended Height**
83.5
150
34
95.5
173
178.5
38
214.5
42
23 Min ID Straddle Width
34
24 Truck Weight
SH 5520-40
SH 5540-40
3025
2840
3130
2945
3570
3385
na
w/o Battery***
3620
** Add 24.7" with Load Backrest
*** Add 85 lb for Load Backrest
Add 120 lb for Side Shift
Aisle Planning Guide
SH 5500 Series
SH 5520
Pallet Length
Pallet
Width
30
36
40
42
48
A
B
A
B
A
B
A
B
A
B
36
40
42
48
in
in
in
in
65
68
69
73
68
69
70
71
65
68
69
73
68
69
70
71
65
68
69
73
68
69
70
71
65
68
69
73
68
69
70
71
68
68
69
73
79
79
73
71
Pallet
Length
SH 5540
Pallet
Width
Pallet Length
Pallet
Width
30
36
40
42
48
A
B
A
B
A
B
A
B
A
B
36
40
42
48
in
in
in
in
65
67
68
71
74
75
75
77
65
67
68
71
74
75
75
77
65
67
68
71
74
75
75
77
65
67
68
71
73
75
75
77
67
67
68
71
82
78
75
77
B
Right Angle Aisles
A = Equal Intersecting Aisles
B = Right Angle Aisles
Add 2.5" if side shift option is used.
Add 6" to 12" to all aisle dimensions for maximum maneuverability.
SH 5500 Series
Technical Information
5. Performance enhancing
features
Capacity
Optional Equipment
1. 30 amp on-board charger
(6.62" battery box)
Operator Controls
4000 lb at 24" load center
Crown’s robust X10 handle
places all control buttons in the
optimum position for ease of
operation with either hand and
to minimize hand and wrist
movements. An ergonomic
forward/reverse thumb wheel
allows for precise maneuvering.
The control hand grips are
urethane covered for insulation
from cold and vibration with
integrated horn buttons for easy
activation. The handle contains a
safety button which reverses the
direction of the truck should the
button touch the operator.
• X10® Handle
Maximum Battery Size
SH 5520-40: 6.62" wide
x 34.37" long x 24.8" high –
up to 300 amp hours, 24 volts
2. Keyless on-off switch
3. Work Assist™ Accessories:
• Clip pad
• Brake override
• Electronic power steering
• Ramp hold and
speed control
SH 5540-40: 13.12" wide
x 31.10" long x 24.8" high –
up to 660 amp hours, 24 volts
• Hook
• Clip pad and hook
• Pocket
• Power boost
• High-visibility mast
and carriage
Standard Equipment
1. 24-volt electrical system
2. Crown’s Access 1 2 3®
Comprehensive
• Fan
4. Sideshift with internal hosing
• Low profile power unit
• Tool storage tray
5. 47" tall load backrest
6. Optional fork lengths (30",
39", 42", 45", 48", 54", 60")
System Control
6. Wire mesh guard - mast
3. Access 1 2 3 display
7. Volkollan drive tire –
10" dia. x 3" wide
7. Freezer conditioning
• Eight-character scrolling
display, 5 button access
The physical efforts to hold the
handle at a comfortable height
was minimized to reduce fatigue.
(Continuous -30° C / -22° F)
8. Polyurethane load wheels –
4" dia. x 2.88" wide
9. InfoPoint® System
8. Plexiglass safety shield
• Three selectable
performance levels
9. 10" dia. x 4" wide drive tire
• Soft poly
• Siped soft poly
10. InfoLink® ready
A rabbit/turtle switch incorpo-
rates two levels of programmable
travel performance so operators
can select the setting that
matches their experience level
or application requirements.
• BDI with lift interrrupt
• Five hour meters
• Event codes
10. Steel power unit covers
11. Emergency power
disconnect
11. SBE 160 battery connector
12. Key switch
13. Horn
• Access 1 2 3
diagnostics with real
time troubleshooting
Exclusive brake override feature
allows slow speed travel with
the handle near vertical. This
feature improves maneuverability
in tight areas.
14. SB175 gray
battery connector
• PIN code capability
4. AC traction and steer motors
15. Reversing button
16. Electric park brake
17. Fork tip indicators
18. Battery compartment
rollers
Technical Information
SH 5500 Series
Performance
Electrical System
A heavy-duty 24-volt fused
electrical system utilizes
microprocessor controls for
maximum energy efficiency,
reduced maintenance and infinite
speed control capability.
Mast
Other Options
The SH 5500 Series incorporates
the latest generation AC drive
system enhanced with Access
1 2 3 technology. Crown’s
Access 1 2 3 technology
High visibility two and three-stage
mast design with angled cross
bracing and lift cylinders located
behind nested I-beams provides
maximum visibility for load
positioning and placement.
Crown’s staging cushions
coupled with lowering dampers
ensure smooth operation.
1. Amber strobe light
2. Travel alarm: reverse, forward
or both
Safety considerations and
dangers associated with audible
travel alarms and strobe lights
include:
continuously monitors truck
systems and adjusts system
parameters to deliver optimum
performance and control. The
Access Display provides a conve-
nient interface for operators
keeping them informed of any
changes impacting truck perfor-
mance and allowing them to
choose from three performance
profiles when enabled.
Access control modules for
travel, lift and steer are sealed
from dirt, dust and moisture
for trouble-free operation. All
contactors have been eliminated
except for the main line contactor.
A 175 amp battery connector with
disconnect handle is standard.
• Multiple alarms and/or lights
can cause confusion.
Rolled steel outer mast channels
and inner I-beams roll on canted,
steel, anti-friction roller bearings
for minimal current draw and long
life. Mast and chain rollers are
sealed and lubricated for life.
Telescoping mast sections nest
to reduce truck length. Heavier
mast cross bracing design
• Workers ignore the alarms
and/or lights after day-in and
day-out exposure.
• Operator may transfer the
responsibility for “looking out”
to the pedestrians.
Hydraulic System
Heavy-duty hydraulic motor
(4.8 kw) is transistor controlled
and matched with a gear type
pump selected for optimum lift
performance and low noise.
Single-speed lift with program-
mable acceleration - deceleration
and programmable two-speed
lowering enables customization
to match operator preference or
application requirements.
Programmable performance
settings enable authorized
personnel to tune the lift truck
to different operator skill levels,
or to meet specific application
requirements. In addition,
up to 25 PIN codes can be
assigned to individual operators
and matched to one of the
pre-programmed performance
profiles if desired.
• Annoys operators and
pedestrians.
increases stiffness.
Serviceability / Durability
The Access display simplifies
service for technicians by
Dimensions and performance
data given may vary due to
manufacturing tolerances.
Performance is based on an
average size vehicle and is
affected by weight, condition of
truck, how it is equipped and the
conditions of the operating area.
Crown products and specifica-
tions are subject to change
without notice.
providing advanced diagnostics
without the need for separate
handsets. The display allows the
technician to view event service
codes and truck hours when
event occurred, perform system
calibrations or functional tests of
components, and make neces-
sary adjustments. Crown’s
InfoPoint System compliments
Access 1 2 3 diagnostics by
providing a Quick Reference
Guide, on-truck component
maps and information nuggets to
further simplify troubleshooting.
All wiring is color coded.
Cylinder rods are hard-plated
chrome with polyurethane seals.
Relief valve tuned to capacity
protects all components in the
hydraulic system. Reservoir
incorporates an in-tank 10
micron return filter for removing
debris from oil.
Electronic power steering allows
the operator to maneuver heavy
loads in tight spaces throughout
the day while minimizing fatigue.
Smooth travel and lift perfor-
mance combine with excellent
controls provided by the X10
handle to increase productivity.
Drive Unit / Brake
Heavy-duty gearbox with
helical spur input gear for quiet
operation.
The SH 5500 Series features
ramp hold and speed control
to improve operation on small
inclines or ramps. The ramp hold
feature uses the motor to prevent
truck movement when the brake
is released and no travel com-
mand is present. The ramp speed
control feature insures that actual
travel speed matches requested
travel speed. If the truck encoun-
ters an obstacle, a power boost
feature delivers up to 15 percent
more power than normally avail-
able for a full three seconds to
overcome the obstruction.
Removable steel power unit
doors are hinged for ease of
opening providing excellent
accessibility to the distribution
panel and all other components.
Steel covers provide added
protection to critical internal
components.
Regenerative motor braking
is activated under a downhill
condition, during plugging or
when the directional control is
returned to neutral. An electro-
magnetic brake, spring applied
and electrically released, is
mounted on top of the drive
motor. The electro-magnetic
brake serves as the parking
brake and applies when the
control handle position moves
from the operating zone to brake
zone during truck operation.
Removable steel battery covers
and hinged cover allow easy
access to the battery. Battery
removal can be accomplished
from either side. Battery compart-
ment rollers are standard.
The X10 handle incorporates a
vacuum die cast process using
high-grade aluminum and benefits
from structural webbing for maxi-
mum strength and durability.
Power Steering
Electronic power steering is pro-
vided by a heavy-duty AC motor
that pivots the drive unit when
steer tiller movement is detected.
Crown Equipment Corporation
New Bremen, Ohio 45869 USA
Tel 419-629-2311
C
Fax 419-629-3796
crown.com
Because Crown is continually improving its products,
specifications are subject to change without notice.
You can count on Crown to build lift trucks
designed for safe operation, but that’s
only part of the safety equation. Crown
encourages safe operating practices through
ongoing operator training, safety-focused
supervision, maintenance and a safe working
environment. Go to crown.com and view our
safety section to learn more.
Crown, the Crown logo, the color beige, the Momentum
symbol, Access 1 2 3, InfoPoint, InfoLink and X10 Handle
are trademarks of Crown Equipment Corporation.
Copyright 2008 Crown Equipment Corporation
SF14905 1/08
Printed in U.S.A.
|