I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Large Flat Panel Static Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PSMH2485
Installation Instructions
PSMH2485
DIMENSIONS
2134
84.00
311
12.24
72
2.85
67
2.65
145
5.73
202
7.97
Manufac turer rec ommends
200 mm(7.97") c lea ra nc e
between the ba c k of the
sc reen a nd the wa ll
889
35.00
69
2.73
743
29.25
1035
40.75
1149
45.25
DIMENSIONS: [MILLIMETERS]
INCHES
1601
63.05
1423
56.01
743
29.25
889
35.00
1035
40.75
73
2.88
R
DIMENSIONS: [MILLIMETERS]
INCHES
3
PSMH2485
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Open-Ended Wrench
Hex-Head Wrench
Ajustar
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Ajuster
TOOLS FOR INSTALLATION/PARTS
7/32"
5/16"
M14 (provided)
B (2)
A (2)
C (4)
M16 x 65mm
D(4)
M16 x 70mm
G (1)
M14
E (2)
F (16)
5/16-18
H (2)
4
Installation Instructions
PSMH2485
Mount Installation
ASSEMBLY AND INSTALLATION
Mount Assembly
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The mount weighs
in excess of 100 lbs (45.36kg). ALWAYS use appropriate
lifting device and follow all safety practices when moving and
installing this mount.
1. Attach two vertical brackets (A) to two horizontal brackets
(B) using sixteen 5/16-18 nylon lock nuts (F). (See Figure 1)
NOTE: Lock nuts should be tightened to no more than 120 in. lbs.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s
responsibility to make sure the structure to which this mount
is being attached can support a minimum of 2,000 lbs
(907.18kg). Reinforce the structure as required before
installing this mount.
(B)
(A)
1. Using appropriate lifting device, raise assembled mount
and place mount against wall in desired installation
location. (See Figure 2)
(A)
2. Level and adjust horizontal position making certain slots in
upper and lower horizontal brackets on mount are properly
positioned over studs.
(F) x 16
1
3. Using a pencil, or similar marking tool, mark the location of
mounting holes in base onto surface. (See Figure 2)
4. Drill eight or twelve 7/32" pilot holes (8 if 24" center studs
and 12 if 16" center studs), at marked locations.
Figure 1
3
(8 places when 24" centers on studs)
(12 places when 16" centers on studs)
7/32" pilot holes
4
2
1
Q-Latch
Figure 2
5
PSMH2485
Installation Instructions
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT
overtighten hardware!
5. Secure mount to studs using 5/16 x 2-1/2" lag screws [not
included] and 5/16" flat washers [not included] (8 if 24"
center studs and 12 if 16" center studs). (See Figure 3)
OPEN
1
Q-Latch
Figure 4
2. Install four mounting buttons (2 of E, 2 of H) onto display
using four socket head screws (C or D). (See Figure 5)
IMPORTANT ! : The two mounting buttons with the notch
in them (H) should be used as the top mounting buttons.
3. Lift display following lifting instructions provided by display
manufacturer.
(8 places when 24" centers on
studs--12 places when 16" centers
on studs)
4. Align mounting buttons on display with teardrop mounting
holes in mount. (See Figure 6)
5
5. Move display forward until recessed area of mounting
buttons is positioned over lower area of teardrop mounting
holes. (See Figure 6)
Figure 3
6. Lower display until recess area of mounting buttons is
seated in lower area of teardrop mounting holes.
(See Figure 6)
Display Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware.
1. Move Q-Latches on mount to the OPEN position.
(See Figure 4)
6
Installation Instructions
PSMH2485
(H) x 2
2
(C or D) x 4
2
2 (E) x 2
Figure 5
Padlock Here
4
6
CLOSE
7
Q-Latch
3
Figure 6
7. Move Q-Latches to Closed position and lock if desired.
(See Figure 7)
Figure 7
8. Route wires and cables to display.
7
PSMH2485
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
Chief Manufacturing, a products
division of Milestone AV Technologies
+31 (0)40 2668615
Asia Pacific
A
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
8831-000015 Rev04
¤2010 Milestone AV Technologies, a
Duchossois Group Company
12/10
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
P
F
|