I N S T A L L A T I O N I N S T R U C T I O N S
XSM
XTM
FUSION EXTRA LARGE HEIGHT ADJUST
FLAT PANEL MOUNTS
XSM/XTM Series
Installation Instructions
XSM/XTM Series
DIMENSIONS
XSM
NOTES:
1. MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS.
2. MAX MOUNTING PATTERN IS 48.4" (1229.4 mm) WITH REVERSED UPRIG HTS.
3. FOR REC ESSED APPLIC ATIONS, MINIMUM VERTIC AL LIFT FOR HOOK ENGAG EMENT IS .56"[14.2].
MOUNT IS 2.23"[56.6mm] DEEP WHEN FLAT TO WALL.
20.6
.81
30
1.18
39.1
1.54
24.3
.96
73.9
2.91
25.4
1.00
MINIMUM UPRIG HT SPACING 24"
8.3
.33
685.8
27.00
0
15
.59
75
2.95
56.6
2.23
44.5
1.75
383.4
15.10
419.6
16.52
5.31
45
1.77
RAILS CAN BE SLID LEFT
OR RIG HT FOR OFFSET
25.4
1.00
1233.4
48.56
DIMENSIONS: [MILLIMETERS]
INCHES
XTM
NOTES:
1. MAX MOUNTING PATTERN IS 44.7" (1135.4 mm) WITHOUT REVERSING UPRIG HTS.
2. MAX MOUNTING PATTERN IS 49.2" (1249.7 mm) WITH REVERSING UPRIGHTS.
.40 10.2
.51 12.9
FOR REC ESSED APPLIC ATIONS, MINIMUM VERTIC AL LIFT FOR HOOK ENG AG EMENT IS .41"[10.4mm].
MOUNT IS 1.92"[48.7mm] DEEP WHEN FLAT TO WALL.
12°
1.00 25.4
.96 24.4
2.00 50.8
2.92 74.1
1.00 25.4
MINIMUM UPRIG HT SPAC ING 24"
.33 8.3
.59 15
0
27.00 685.8
27.00 685.8
.59 15
1.75 44.5
15.10 383.4
2.95 75
1.92 48.7
MIN.
16.52 419.6
DEPTH
5.31
RAILS C AN BE SLID LEFT
OR RIG HT FOR OFFSET
48.54 1233
DIMENSIONS: [MILLIMETERS]
INCHES
3
XSM/XTM Series
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
XSM/XTM Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
7/32" (5.5mm) Wood Stud
5/16" (7.9mm) Concrete
PARTS
[A-K used on XSMU/XTMU Models Only]
B (6)
A (6)
M6x25mm
M6x16mm
C (6)
M8x20mm
E (4)
M8x50mm
D (6)
M8x30mm
M (1)
[Included with
XSMXXXX / XTMXXXX
Models Only]
G (6)
M10x50mm
F (6)
M10x40mm
Custom
XSMXXXX /
XTMXXXX
Hardware
H (6)
M6
I (6)
M8
N (1)
(XTM Only)
JA (6)
.750x.323x.250"
JB (6)
1.00x.400x.75"
P (1)
3/16" - 12"
KA (1)
M5
KB (1)
M6
R (1)
T (1)
LA (4)
5/16"
LB (4)
5/16"
Q (4)
LC (4)
5/16" x 2-1/2"
S (1)
U (1)
(XSM Only)
(XTM Only)
5
XSM/XTM Series
Installation Instructions
INSTALLATION
Center of screen
The XTM and XSM have been designed to be mounted directly
onto either a wood stud or concrete wall. The XTM has brackets
which allow the display to be tilted. The XSM has static brackets
which keep the display in an upright position.
7-1/2"
(190.5mm)
Locate Mounting Site
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the weight of the XTM or XSM and all attached equipment not
to exceed 250 lbs (113.4 kg).
Vertical center
of mount
NOTE: For concrete installation, proceed to Installing to a
Concrete Wall section.
Installing to a Wood Stud Wall
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 24" (609.6mm). Do not
place mounting brackets closer together than 24" (609.6mm).
When attaching to a wall containing studs located 16" on
center, space the uprights 32" (812.8mm) apart.
Figure 1
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
1. Determine the center of the display, and where it should be
located on the wall.
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
2. Locate the appropriate studs to the left and right of the
selected location.
NOTE: If the screen area lies over a stud, use that stud and an
appropriate stud to either the left or right of it.
3. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
4. Measure up 7-1/2" (190.5mm) from the center point to mark
location of the upper mounting slots.
6. Drill one 7/32" pilot hole in each stud.
7. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat
washers (LB) to attach top of mount to wall. (See Figure 2)
6
Installation Instructions
XSM/XTM Series
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
6
5
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
7
(LC) x 4
10
8
9
8
9
4
5
(LA) x 4
6 10
x4
(LB) x 4
Figure 2
8. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
9. Drill 7/32" pilot holes at markings for lower mounting holes.
(See Figure 2)
10. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat
washers (LB) to attach the mount to the wall through the
lower mounting holes. (See Figure 2)
11. Slide rails to approximate center of screen location.
12. Proceed to Attaching Interface Brackets to Display
(LC) x 4
7 11
section.
(LB) x 4
Installing to a Concrete Wall
Figure 3
5. Drill one 5/16" pilot hole at each marking. (See Figure 3)
CAUTION: MINIMUM HORIZONTAL DISTANCE
6. Install an anchor (LA) into each pilot hole using a hammer.
(See Figure 3)
BETWEEN WALL BRACKETS IS 24" (609.6mm). Do not
place mounting brackets closer together than 24" (609.6mm).
7. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat
washers (LB) to attach top of mount to anchors in wall. (See
Figure 3)
1. Determine the center of the display, and where it should be
located on the wall.
2. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
8. Mark the attachment points for the lower mounting slots.
(See Figure 3)
3. Measure up 7-1/2" (190.5mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
9. Drill one pilot hole at each marking for lower mounting
holes. (See Figure 3)
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
10. Install an anchor (LA) into each pilot hole using a hammer.
(See Figure 3)
11. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat
washers (LB) to attach the mount to the wall through the
lower mounting holes. (See Figure 3)
12. Slide rails to approximate center of screen location.
7
XSM/XTM Series
Installation Instructions
Switching Interface Brackets (Optional)
Attaching Interface Brackets to Display
1. Align the center of the bracket with center of screen.
(See Figure 4)
If an installation situation makes adjusting the location of
interface brackets necessary, there are several options.
NOTE: The diamond-shape hole in the bracket corresponds to
1. The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 5)
the center of the mount.
2. The location of the left and right interface brackets may be
switched, with the knobs on the XTM interface brackets
facing the inside of the mount. (See Figure 5)
1
Knobs
Center of bracket
Figure 4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2
2. Select correct screws, spacers (if necessary) and washers
from the hardware bag (A-K) and attach brackets to back of
screen. (See Figure 4)
Figure 5
8
Installation Instructions
XSM/XTM Series
3. If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets to be reversed.
(See Figure 6)
2. Adjust Velcro® pull strap (if necessary) so it does not
extend beyond bottom of screen. (See Figure 8)
NOTE: NEVER place both interface brackets to one side of the
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
wall mount center line! (See Figure 8)
NOTE: Do NOT allow both interface brackets to be located on
same side of wall bracket. (See Figure 8)
d. Remove the knob, washer and screw.
e. Replace the knob, washer and screw in the opposite
order, with the knob on the inside of the bracket.
Center Line (CL)
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
3d
Pull strap
3e
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Knobs to outside
of brackets
Figure 6
Attaching Screen to Wall Mount
1. Attach wall bracket caps (Q) to top and bottom of both wall
brackets. (See Figure 7)
Both interface brackets must NEVER be located
to one side of the wall brackets!
Figure 8
1
(Q) x 4
Figure 7
9
XSM/XTM Series
Installation Instructions
XTM Model
XSM Model
8. Push interface bracket tab all the way down so that the
lower mounting slot is blocked. (See Figure 10)
NOTE: Proceed to Step 8 for XSM Model instructions.
3. Hang top hook of interface brackets onto the top bar of the
mount. (See Figure 9)
NOTE: The screen initially installs into the "kickstand mode" to
allow easy cable access.
Latch
closed
4. Slide screen and bars to desired viewing position.
5. Route cables between wall and bars.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
Latch
open
6. Pull downward on the pull straps and swing inward toward
wall, latching interface brackets to lower bar and locking
bottom of screen to the mount. (See Figure 9)
7. Proceed to Adjusting Roll/Height of Wall Brackets
section.
Interface
bracket
tab
12
(Screen not shown for clarity)
8
10
Top
Hook
Figure 10
3
9. Hang the top hook of interface brackets onto the top bar of
the mount. The bottom of the screen will be away from the
wall.
10. Move screen towards the wall by pulling display bottom
away from wall and pushing the interface bracket tabs up
one notch to the detent which you will be able to feel
(approximately half way up).
11. Push bottom of display toward the wall bracket so that lower
latch on interface bracket surrounds lower bar of wall
mount.
12. Raise interface brackets tabs all the way to secure the
brackets onto the wall mount. (See Figure 10)
6
Pull straps
Figure 9
10
Installation Instructions
XSM/XTM Series
Adjusting Roll/Height of Wall Brackets
Locking XSM Mount (Optional)
Add padlock (not included) to interface bracket tab to lock the
XSM mount. (See Figure 13)
NOTE: The height adjust wall brackets allow adjustment of
+ 1/2".
1. Turn to right (tighten) to raise side of screen.
(See Figure 11)
2. Turn to left (loosen) to lower side of the screen.
1
Raises screen
Lowers screen
2
(P)
Add padlock
(Screen not shown for clarity)
Figure 11
Figure 13
Locking XTM Mount (Optional)
1. Add optional security bracket (N) to the mount.
(See Figure 12)
2. Add padlock (not included) to complete security.
(XTM Shown)
(N)
1
2
Figure 12
11
XSM/XTM Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
+31 (0) 495 580 845
Chief, a products division of
Milestone AV Technologies
Asia Pacific
A
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
8800-002518 Rev00
¤2014 Milestone AV Technologies
03/14
P
F
|