I N S T A L L A T I O N I N S T R U C T I O N S
Security SLM Series Mount
RPMA1, -B1, -C1
Installation Instructions
RPMA1, -B1, -C1
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
RPMA1, -B1, -C1
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
5/32"
(Provided)
PARTS
Q (1)
S (1)
5/32"
T (8)
U (4)
V (4)
R (4)
A (4)
10-24 x 1/4"
(NOT USED)
D (4)
M5 x 12mm
G (4)
M2.5 x 10mm
K (4)
M5 x 12mm
M (4)
M4
B (4)
M3 x 10mm
H (4)
M3 x 10mm
N (4)
M6
E (4)
M6 x 12mm
L (4)
M6 x 12mm
C (4)
M4 x 10mm
F (4)
1/4-20 x 1/2"
J (4)
M4 x 10mm
P (4)
O (1)
3/32"
4
Installation Instructions
RPMA1, -B1, -C1
6. Pull RPMA1 bottom away from RPMA1 top.
ASSEMBLY AND INSTALLATION
Attaching Projector Security Legs
Installing Ceiling Plate and Disassembling
RPMA1
1. Attach the projector security legs (R) to the projector, using
the correct size screws and washers for your specific
projector. (See Figure 3)
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
x 4
1. Install ceiling plate and extension accessories following
installation instruction provided by manufacturer.
2. Insert key into lock and turn to unlock the projector from
RPM head. (See Figure 1)
(M) or (N) x 4
3. Moving locking lever to "Unlocked" position. (See Figure 1)
4. Remove the RPM head from RPMA1 top. (See Figure 1)
(R) x 4
x
Projector
4
Figure 3
2. Add washers (U) to the projector security legs (R). Add
spacers (T) as necessary to level the projector security legs
(R). (See Figure 4)
2
3
2
Figure 1
(U) x 4
5. Remove and keep four Phillips screws from top of RPMA1.
(See Figure 2)
(T) x 4
x 4
5
Figure 4
Attaching Projector to RPMA1 Bottom
1. Align projector and RPMA1 bottom so that the projector is
oriented correctly.
Figure 2
5
RPMA1, -B1, -C1
Installation Instructions
2. Remove the paper backing from the adhesive washers (V)
and attach projector to RPMA1 bottom using adhesive
washers (V) and thumbnuts (P) over the security legs (R).
(See Figure 5)
(P) x 4
(V) x 4
4
RPMA1
Bottom
Security
Legs (R)
5
Projector
Figure 7
Attachment areas if using an
optional SLB bracket.
4. Move locking lever to "Locked" position. (See Figure 7)
5. Insert key into lock and turn to secure projector to mount.
(See Figure 7)
Figure 5
Attaching RPMA1 to Threaded Pipe
NOTE: An optional SLB bracket may be purchased and used
to attach projector to RPMA1. (See Figure 5)
3. Attach RPMA1 bottom to RPMA1 top using four Phillips
screws removed in Step 5 of Installing Ceiling Plate and
Disassembling RPMA1. (See Figure 6)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO
NOT substitute hardware. Use only the hardware provided by
the manufacturer.
3
x 4
1. Align RPMA1 with end of NTP pipe. (See Figure 8)
2. Thread RPMA1 up onto pipe by turning counterclockwise
until hand tight. (See Figure 8)
2
1
Figure 6
Figure 8
6
Installation Instructions
RPMA1, -B1, -C1
3. Tighten YAW adjustment locking screw using a #2 Phillips
screwdriver.
Rough Alignment of RPMA1
1. Turn RPMA1 clockwise or counterclockwise until the front of
the RPMA1 and projector is facing target. (See Figure 9)
PITCH Adjustment
1. Loosen PITCH adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 11)
1
2. Turn PITCH micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten PITCH adjustment locking screw using a #2 Phillips
screwdriver.
2
1
2
Secure set screw,
then Phillips screw
from under set screw.
3
Figure 9
2. Secure set screw and security Phillips screw under set
screw. (See Figure 9)
Adjustments
The RPMA1 can be adjusted for rotation (yaw), vertical
elevation (pitch), and horizontal tilt (roll).
Figure 11
ROLL Adjustment
1. Loosen ROLL adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 12)
2. Turn ROLL micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten ROLL adjustment locking screw using a #2 Phillips
screwdriver.
1
3
2
1
3
Figure 10
YAW Adjustment
2
1. Loosen YAW adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 10)
2. Turn YAW micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
Figure 12
7
RPMA1, -B1, -C1
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8802-000254
¤2007 Chief Manufacturing
04/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
|