I N S T A LL A T I O N IN S T R U C T IO N S
LARGE FLAT PANEL DISPLAY STATIC MOUNT
PST 2000 Series
The PST static wall mount accommodates large flat
screens weighing up to 200 lbs (90.72kg). The teardrop
holes in the mount allow for quick connect/disconnect of
the screen, thus simplifying installation and maintenance
processes.
The top and bottom mounting brackets are adaptable to
supporting framework with wood studs that are 16” on
center or 24”on center.
The mount has integrated lateral shift, allowing for four
different mounting options. For dual wood studs 16” on
center, the lateral shift is + 4.5 inches. For dual wood
studs 24” on center, the lateral shift is + 0.5 inches.
After installing the flat screen on the mount, the screen
can be locked in place using the convenient locking flag.
A padlock can be used on the latching flag for added
security.
The mount is concealed behind the display, making it a
low profile wall mount.
! IMPORTANT: If the installation of this product
requires OSHPD seismic approval, refer to OSHPD
pre-approval documents and drawings before beginning
installation. OSHPD documents and drawings are
PST 2000 Series
product information page for the mount.
BEFORE YOU BEGIN
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly
study all instructions and illustrations before you begin to install the mount brackets. Pay particular atten-
tion to the “Important Warnings and Cautions” on Page 2.
x
x
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
The maximum weight to be installed on the PST mount is 200 lbs (90.72kg).
Chief Manufacturing, a division of Milestone AV Technologies
8804-000255 Rev F
8401 Eagle Creek Parkway, Savage, MN 55378 ©2008 Milestone AV Technologies
P: 800.582.6480 / 952.894.6280 F: 877.894.6918 / 952.894.6918
10/08
Installation Instructions
PST 2000 Series
PARTS LIST
Prior to assembly, unpack the carton completely. Verify
contents listed in Table 1 and Figure 1.
CONTENTS
DIMENSIONAL DRAWING ..................................... 2
TOOLS REQUIRED FOR INSTALLATION.............. 3
PARTS LIST .............................................................. 3
PST INSTALLATION................................................ 4
Select Mounting Location........................................ 4
Flag Extender Installation (OPTIONAL).................. 4
Mount the PST ........................................................ 5
ATTACH PSB TO THE DISPLAY............................. 6
INSTALL THE DISPLAY.......................................... 6
REMOVE THE DISPLAY.......................................... 6
Read installation instructions completely. If you are
missing any of the listed parts, contact Customer Service
at: 1-800/582-6480.
Table 1. Parts List
REF DESCRIPTION
QTY
10
20
30
40
50
60
Plasma Static Mount
1
2
2
2
4
4
Flag Extender
Phillips Machine Screw, 10-24 x ½”
Thin Nylock Nut, 10-24
Lag Bolts, 5/16” x 2-½”
Flat Washer, 5/16”
TOOLS REQUIRED FOR
INSTALLATION
x
x
x
Drill and drill bit set
Socket wrench set
30
#2 Phillips Screwdriver
NOTE: Other tools may be required depending on your
method of installation.
20
10
40
4 Lag Bolts
50
4 Washers
60
Figure 1. Parts
3
Installation Instructions
PST 2000 Series
PST INSTALLATION
Perform the following procedures to mount the PST.
Hang the mount on
the wall temporarily
using a nail in the
center hole. Level the
mount before drilling
pilot holes.
Select Mounting Location
To select the mounting location, do the following:
WARNING: It is the responsibility of the installer to
verify that the wall to which the mount is
anchored will safely support the
combined load of all attached
components and equipment.
Figure 2. Use Triangular Hole to Hang the Mount
1. Determine the exact mounting location to install the
wall mount prior to installation, keeping in mind the
screen size.
Wood Studs
16” or 24”
NOTE: Mount the PST on dual wall studs or some other
equivalent supporting framework that is vertical
or horizontal.
Wall
Pilot Holes
2. Using a stud sensor, locate the two wood studs where
you will mount the PST. Refer to Figure 3 for dual
wood studs that are 16” or 24” apart on center.
3. Using a nail as a temporary hook, hang the mount on
the wall using the triangular hole located in the center
of the mount (see Figure 2).
Pilot Holes
4. Use a pencil to mark the mounting holes where the
four pilot holes will be drilled into the center of the
wood stud. Make sure the mounting holes are square
and straight. Remove the mount from the wall,
placing it on the floor or a table.
Figure 3. Wood Studs 16” or 24”Apart on Center
5. Drill the pilot holes using a 7/32” drill bit.
Flag Extender Installation (OPTIONAL)
To install the optional flag extenders, perform the
following (Refer to Figure 4):
1. Insert extender (20) slot into top of latching flag.
2. Install screw (30) through latching flag and extender
(20) into nut (40).
3. Repeat for opposite side.
Figure 4. Optional Flag Extenders
4
Installation Instructions
PST 2000 Series
PST INSTALLATION (Cont’d)
Mount the PST
To mount the PST, do the following:
1. Holding the PST against the wall, select the pair of
mounting holes that best suits your situation (see
Figures 5, 6, and 7).
Option A
NOTE: The mounting holes are slotted to allow for a
small degree of lateral movement. The mount can
be centered, or shifted to the left of center, or
right of center depending on stud location.
2. Depending on your situation, install the lag bolts (50)
and washers (60) into the pilot holes previously
drilled, as described below.
Figure 5. Mounting Holes – 16” Apart on Center
(Option A)
x
x
x
Option A. Install four 5/16” x 2-½” lag bolts
(50) and four 5/16” washers (60) (two top and
two bottom) into the mounting holes, centering
the PST on dual wood studs 16” apart on center
as shown in Figure 5.
Option B
Option C
OR
Option B. Install four 5/16” x 2-½” lag bolts (50)
and four 5/16” washers (60) (two top and two
bottom) into the mounting holes that are right of
center on dual wood studs 16” apart as shown in
Figure 6.
OR
Option C. Install four 5/16” x 2-½” lag bolts
(50) and four 5/16” washers (60) (two top and
two bottom) into the mounting holes that are left
of center on dual wood studs 16” apart dual
wood studs 16” apart on center as shown in
Figure 6.
Figure 6. Mounting Holes – 16" Apart on Center
(Options B and C)
OR
x
Option D. Install four 5/16” x 2-½” lag bolts
(50) and four 5/16” washers (60) (two top and
two bottom) into the mounting holes, centering
the PST on dual wood studs 24” apart on center
as shown in Figure 7.
Option D
3. Tighten all lag bolts.
Figure 7. Mounting Holes – 24" Apart On Center
(Option D)
5
Installation Instructions
PST 2000 Series
ATTACH PSB TO THE DISPLAY
To attach the PSB to the display, do the following:
x
To help your identify the correct PSB that
matches the model number of your display, refer
to the cross-reference chart at
x
To download the corresponding PSB installation
INSTALL THE DISPLAY
To install the display, do the following:
To install display, align
NOTE: Verify that all power/audio/video cables are
disconnected from the display and the latching
flag is lowered in the down position before
attempting to mount the display.
the mounting buttons on
the PSB with teardrop
slots on the mount.
1. With the aid of another person, lift the display up to
the mount (10) on the wall, aligning mounting
buttons on the PSB with the teardrop slots on the
mount, and lower the display firmly into place
(Figure 8).
Figure 8. Mount Plasma Static Bracket to Wall
2. Raise the latching flag (2 places) to secure the display
(see Figure 9). If the flag does not fully engage,
check to ensure the mounting buttons are fully seated
in the slots.
Raise
NOTE: A padlock may be installed through the hole in
latching
flag to
lock
the latching flag for additional security.
display
REMOVE THE DISPLAY
To remove the display from the mount, do the following:
1. Disconnect all power/audio/video cables.
Figure 9. Raise Latching Flag to Lock
2. Lower the latching flag to unlock the display
(see Figure 10).
3. With the aid of another person, lift the display up and
out of the teardrop slots in the mount to remove the
display.
Lower
latching
flag to
unlock
display
Figure 10. Lower Latching Flag to Unlock
6
Installation Instructions
PST 2000 Series
7
Installation Instructions
PST 2000 Series
8
|