I N S T A L L A T I O N I N S T R U C T I O N S
Single and Dual Display Floor Stands
MF1, MF2, PF1, PF2 Series
Installation Instructions
MF1, MF2, PF1, PF2 Series
DIMENSIONS
MF1, MF2
[1463]
57-5/8
[1316]
51-7/8
[889]
35
[661]
26
[431]
17
[2327]
91-5/8
[2180]
85-7/8
[1211]
47-5/8
[39]
1-1/2
[44]
1-3/4
[65]
2-1/2
PF1, PF2
3
Installation Instructions
MF1, MF2, PF1, PF2 Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Installation Instructions
MF1, MF2, PF1, PF2 Series
TOOLS REQUIRED FOR INSTALLATION
1/4"
(To remove base
plates from packaging)
3/16"
(included)
PARTS
A (1)
D (1)
(PF Only)
F (1)
(D)
[(2) for Dual
Display Models]
OR
(E)
B (1)
(Single Display
Models Only)
C
[(2) for Single Display Models]
[(4) for Dual Display Models]
E (1)
(Front)
(MF Only)
[(2) for Dual
Display Models]
G (4)
J (1)
3/16"
H (1)
3/16"
N (4)
5/16-18 x 1-1/2"
P (1)
K (1)
M (4)
5/16-18 x 3/4"
Q (4)
5/16"
L (12)
5/16-18 x 1/2"
1/4-20 x 3/8" 1/4"
(Dual Display Only)
5
MF1, MF2, PF1, PF2 Series
Installation Instructions
2. Gather stand base pieces B and C (2) as shown in Figure 3
and push them together until the edges meet.
ASSEMBLY
(B)
CAUTION: Attachment holes may be damaged if a power
drill is used to insert button head cap screws. Screws should
first be inserted and turned BY HAND with the hex key or with
a handheld screwdriver BEFORE using the hex head drill bit
and power drill to complete the attachment.
Assembling Base for Single Display Stand
1. Attach top base section (A) to the center post (F) using four
5/16-18 x 1-1/2" buttonhead cap screws (N) and four 5/16"
flat washers (Q). (See Figure 1)
(F)
(Front)
(C)
2
Figure 3
1
3. Place top base section and center post assembly on top of
the three base pieces with the center post front facing base
pieces (C). (See Figure 4)
NOTE: To help
determine front of
base - distance (1)
is shorter than
distance (2).
4. Fasten lower base pieces (B and C) to top base section and
center post assembly using twelve 5/16-18 x 1/2" flat head
cap screws (L). (See Figure 4)
(A)
[labeled "FRONT"]
(L) x 12
4
(Q) x 4
(N) x 4
1
(F)
(Front)
Figure 1
(B)
NOTE: Ensure that post (F) front is placed to the front of base
section (A). Check for "FRONT" on base section (A).
(See Figure 1)
NOTE: Insert and tighten screws in order shown (1, 2, 3, 4) in
Figure 2.
(C)
1
Figure 4
4
Assembling Base for Dual Display Stand
3
1. Follow Step 1 (and Figures 1 and 2) of Assembling Base
2
for Single Display Stand.
2. Gather four base pieces (C) as shown in Figure 5 and push
them together until the edges meet.
Figure 2
6
Installation Instructions
MF1, MF2, PF1, PF2 Series
(PF1 Shown)
(Back view of stand)
(M) x 4
(D) or (E)
(C) x 4
(F)
Figure 5
3. Place top base section and center post assembly on top of
the four base pieces. (See Figure 6)
Figure 7
4. Fasten lower base pieces to top base section and center
post assembly using twelve 5/16-18 x 1/2" flat head cap
screws (L). (See Figure 6)
Attaching Dual Head Assembly
1. Place head assembly (D) or (E) on the front of the stand
assembly. (See Figure 8)
(M) x 4
3
(L) x 12
4
(F)
Front
2
1
(P)x1
Back of stand
(C) x 4
(K) x 1
(MF2 Shown)
4
Figure 8
Figure 6
2. Place second head assembly (D) or (E) on the back of the
stand assembly, and on top of the front head assembly.
(See Figure 8)
Attaching Single Head Assembly
1. Attach head assembly (D) or (E) to the stand assembly
using four 5/16-18 x 3/4" button head cap screws (M). (See
Figure 7)
3. Use four 5/16-18 x 3/4" button head cap screws (M) to
fasten through both head assemblies. (See Figure 8)
4. Fasten through back head assembly and back of stand
assembly using one 1/4-20 x 3/8" button head cap screw (K)
and one 1/4" washer (P). (See Figure 8)
7
MF1, MF2, PF1, PF2 Series
Installation Instructions
Attaching Display to Stand
WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY
MAY LEAD TO SERIOUS PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installer’s responsibility
to ensure the total amount of weight placed on the stand
does not exceed 125 lbs (56.70 kg) for the MF1, 250 lbs
(113.40 kg) for the MF2 [125 lbs (56.70 kg) per faceplate];
200 lbs (90.72 kg) for the PF1, 400 lbs (181.44 kg) for the
PF2 [200 lbs (90.72 kg) per faceplate].
5
CAUTION: Before attaching display(s) to the stand ensure
the stand is on level surface.
CAUTION: ALWAYS remove the display(s) BEFORE
adjusting the height of the stand.
Figure 10
1. Adjust the stand to the desired height by holding the top part
of the post, pulling out knob on the center post and turning
o
WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF
40 LBS! Always use two people and proper lifting techniques
when installing or positioning display on stand.
90 in either direction to disengage the locking mechanism.
(See Figure 9)
5. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes.
(See Figures 10 and 11)
2
1
WARNING: IMPROPER INSTALLATION CAN LEAD TO
STAND OR DISPLAY FALLING CAUSING SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT!
Ensure mounting buttons are completely engaged in
mounting holes.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 11)
Figure 9
o
2. Raise or lower the center post, then turn the knob 90 either
direction to engage the knob and lock the stand at desired
height. (See Figure 9)
Remove pin
4
IMPORTANT ! : Set the height of the stand so the display
does NOT rest on the lower part of the post. (See
Figure 9) Always set the height so the knob is engaged in
a hole in the center post.
and nut and
move to lower holes
3. Attach PSBU or MSBU interface bracket(s) to the display(s)
following the instructions included with the bracket.
5
4. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in head assembly. (See Figures 10 and 11)
A padlock or bolt may
be placed through latch
holes
Figure 11
8
Installation Instructions
MF1, MF2, PF1, PF2 Series
Tilting Display
o
(Rear
view of
center post)
(Front view
of center post)
The display(s) can be tilted up to 15 either backward or
forward from a straight upright position. In a dual stand, the
tilting is only restricted by the size of the display.
2
3
1
1. Turn knob counterclockwise on back of head assembly to
loosen the tilt. (See Figure 12)
Exits for
signal cables
Exit for
power
cables
3
1
Snap-on
covers
4
Place optional bolt
(not provided) here
to lock in an upright
position.
(PF1 Shown)
Figure 13
Figure 12
Attaching Stand to Floor
o
2. Tilt display as desired, to a maximum of 15 either forward
The floor stand may be attached to the floor for a more
permanent installation.
or backward.
3. Turn knob clockwise to tighten display on head assembly.
(See Figure 12)
1. Attach the floor stand to the floor using 5/16" or 3/8"
fasteners (not provided) which are appropriate for the floor’s
construction. (See Figure 14)
CAUTION: Tighten knob on back of head assembly to
prevent damage to the stand.
4. If leaving the display in a straight upright position, it is
recommended that a bolt (not provided) be placed through
the head assembly (see Figure 12) to lock the display into
the upright position.
Additional
fastener in
this corner
Cable Management
1. Signal cables can be run down the front flap of the center
post and out the front ofthe post atany of the openings.
(See Figure 13)
2. The display power cord can be run through the top and
down through the post to exit out the back. (See Figure 13)
Single Display Base
Dual Display Base
3. Any accessory power cords can be run through the front
and down through the post to exit out the back. (See
Figure 13)
Figure 14
4. Install the snap-on covers to any opening that is not being
used. (See Figure 13)
5. To remove the snap-on covers, grip the sides of the cover
in the middle and pull off. They can also be removed by
inserting a flat-blade screwdriver into the bottom slot and
prying them off.
9
MF1, MF2, PF1, PF2 Series
Installation Instructions
Using the Stand
Remove bolt
or padlock
if used
1
CAUTION: This stand is intended for use only with the
products and maximum weights indicated: 125 lbs (56.70 kg)
for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs
(56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1,
400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per
faceplate]. Use with other products or products heavier than
the maximum weights indicated may result in instability
causing possible injury.
2
Pin in
"Closed"
position -
move to
"Open"
position to
remove
display
WARNING: STAND CAN TIP OVER RESULTING IN RISK
OF INJURY. Never move the stand when displays are
attached. Never push against the stand.
Removing Display(s) from Stand
1. Remove bolt or padlock from faceplate (if used).
4
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 15)
WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF
40 LBS! Always use two people and proper lifting techniques
when installing or positioning display on stand.
Pin in
"Open"
position -
move to
"Closed"
position
3. Carefully lift display(s) from stand.
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position.
after display
is removed.
Figure 15
10
Installation Instructions
MF1, MF2, PF1, PF2 Series
11
MF1, MF2, PF1, PF2 Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8809-000039 Rev. C
¤2007 Chief Manufacturing
11/07
P
F
+86-755-8996 9226
+86-755-8996 9217
|