WET/DRY VACUUM
13 GAL. CAPACITY
Model 97677
SET UP AnD OPERATInG InSTRUCTIOnS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MAnUAL.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve-
ments, actual product may differ slightly from the product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10c
outlets will reduce risk of electric
shock.
before plugging in. Carrying power
tools with your finger on the switch
or plugging in power tools that have
the switch on invites accidents.
b. Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
d. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
c. Do not expose power tools to rain
or wet conditions. Water entering a
power tool will increase the risk of
electric shock.
e. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts.
d. Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged or
entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
e. When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
b. Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
3. Personal safety
a. Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you are
tired or under the influence of drugs,
alcohol or medication. A moment
of inattention while operating power
tools may result in serious personal
injury.
c. Disconnect the plug from the power
tool before making any adjustments,
changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
b. Use safety equipment. Always wear
ANSI-approved eye protection.
Safety equipment such as dust
mask, non-skid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
c. Avoid accidental starting. Ensure
the switch is in the off-position
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 3
power tool’s operation. If damaged, 7. Do not leave the Wet/Dry Vacuum
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
unattended when it is plugged into
an electrical outlet. Turn off the tool,
and unplug it from its electrical outlet
before leaving.
f. Use the power tool and its
accessories in accordance with
these instructions and in the manner
intended for this particular type of
power tool, taking into account the
working conditions and the work to
be performed. Use of this power tool
for operations different from those
intended could result in a hazardous
situation.
8. This Wet/Dry Vacuum is designed
for vacuuming only non-harmful
substances and non-flammable
liquids. Do not use the Vacuum for
flammable or explosive liquids or hot
and flammable dust.
9. Prior to emptying liquid from the Wet/
Dry Vacuum, make sure to turn off
its Power Switch and unplug the tool
from its electrical outlet.
5. Service
a. Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power
tool is maintained.
10. Keep the Nozzles and Filters clean
and in proper working condition to
ensure the Wet/Dry Vacuum operates
better and more safely.
11. This product is not a toy. Keep it out
of reach of children.
Specific Safety Rules
1. Maintain labels and nameplates
on the Wet/Dry Vacuum. These
carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a
12. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
people with pacemakers should:
• Avoid operating alone.
replacement.
2. Do not remove the Grounding Chain
(44) from this product.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
3. Connect the Wet/Dry Vacuum to a
GFCI outlet and remove the paper
filter before wet pick-up operation.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
4. Discontinue use and empty Cannister
if Motor becomes labored.
5. Do not pull the Wet/Dry Vacuum by
its Hose.
13. Some dust created by vacuuming,
power sanding, sawing, grinding,
drilling, and other construction
6. Store indoors. For household use
only.
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 4
activities, contains chemicals
GROUnDInG
known [to the State of California] to
cause cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
TO PREVEnT
ELECTRIC ShOCk
AnD DEATh FROM
WARnInG
InCORRECT GROUnDInG
WIRE COnnECTIOn:
Check with a qualified
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. never
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
chemically treated lumber
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
14. The warnings, precautions,
and instructions discussed in
this instruction manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Grounded Tools: Tools with Three
Prong Plugs
SAVE ThESE
InSTRUCTIOnS.
3-Prong Plug and Outlet
1. Tools marked with “Grounding
Required” have a three wire cord
and three prong grounding plug.
The plug must be connected to a
properly grounded outlet. If the tool
should electrically malfunction or
break down, grounding provides a
low resistance path to carry electricity
away from the user, reducing the risk
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 5
of electric shock. (See 3-Prong Plug
and Outlet.)
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
2. The grounding prong in the plug is
connected through the green wire
inside the cord to the grounding
system in the tool. The green wire
in the cord must be the only wire
connected to the tool’s grounding
system and must never be attached
to an electrically “live” terminal. (See
3-Prong Plug and Outlet.)
Extension Cords
1. Grounded tools require a three wire
extension cord. Double insulated
tools can use either a two or three
wire extension cord.
2. As the distance from the supply
outlet increases, you must use a
heavier gauge extension cord. Using
extension cords with inadequately
sized wire causes a serious drop in
voltage, resulting in loss of power and
possible tool damage.
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
(See Table A, next page.)
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table A.)
Double Insulated Tools: Tools
with Two Prong Plugs
4. When using more than one extension
cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table A.)
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table A.)
Outlets for 2-Prong Plug
1. Tools marked “Double Insulated”
do not require grounding. They
have a special double insulation
system which satisfies OSHA
requirements and complies with the
applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the
National Electrical Code. (See
Outlets for 2-Prong Plug.)
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
2. Double insulated tools may be used
in either of the 120 volt outlets shown
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 6
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
Symbology
Double Insulated
RECOMMEnDED MInIMUM WIRE
GAUGE FOR EXTEnSIOn CORDS*
(120/240 VOLT)
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
EXTEnSIOn CORD
nAMEPLATE
LEnGTh
AMPERES
(at full load)
V~
A
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
No Load Revolutions per Minute
(RPM)
5.1 – 7.0
n xxxx/min.
0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TABLE A
OPERATInG InSTRUCTIOnS
SPECIFICATIOnS
120 V~ / 60 Hz
Read the EnTIRE IMPORTAnT
SAFETY InFORMATIOn section
at the beginning of this manual
including all text under
1200 Watts
Electrical
10 Amp Motor
Power Switch Type: ON/OFF
Power Plug: 3 Prong, Grounded
Requirements
Tank Capacity 13 Gallons
Stainless Steel Tank / Safety
subheadings therein before set
up or use of this product.
Features
Float / Built-In Storage for Power
Cord & Accessories
TO PREVEnT
SERIOUS
WARnInG
Filter Cartridge / Foam Filter /
Dust Bag / Telescopic Suction
Tube / Wet & Dry Brush / Crevice
Nozzle / Furniture Brush
InjURY FROM ACCIDEnTAL
OPERATIOn:
Accessories
Turn the Power Switch of the
Wet/Dry Vacuum to its “OFF”
position and unplug the
tool from its electrical outlet
before assembling or making
any adjustments to the tool.
UnPACkInG
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 7
Product Features
FIGURE A
50
1. See Figure A.
a.Suction hose (50).
b.Telescopic Suction Tube (82).
c. Drain hose (29).
d.Upper handle (18).
e.Switch knob (80).
f. Upper Cover (9).
g.handle Pipe (19)
h.Lower handle (20).
i. Intake Port (49).
j. Tank (35).
82
18
80
67
29
9
19
20
49
35
36
40
45
83
84
63
k. Wheel Cover (36).
l. Wheel (40).
54
53
45
85
m.
Caster (45).
n.Wet & Dry Brush (83).
o.Filter Cage (84).
29
82
83
p.Safety Float (63).
86
88
q.Cartridge Filter (54).
r. Foam Filter (85).
50
87
s. Crevice nozzle (86).
t. Furniture Brush (87).
u.Filter Cover (53).
nOTE:
For additional information on the Product
Features listed above, refer to the
Assembly Diagram
v. Air Flow Adjusting knob (67).
w.Dust Bag (88).
near the end of this manual.
REV 10c
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 8
(67) to the left or right.
(See Figure A.)
General Operation Instructions
11. Guide the accessory Wet & Dry
Brush (83), Crevice Nozzle (86),
(Furniture Brush (87) with slight
pressure, slowly and evenly, over the
dirt and debris. (See Figure A.)
Dry Vacuuming:
1. Unlock the Right Latch (34) and Left
Latch (59). Then remove the Upper
Cover (9).
(See Figure A, and Assy. Diagram.)
12. When finished vacuuming, turn
the Switch Knob (80) to its “OFF”
position. Then unplug the Wet/Dry
Vacuum from its electrical outlet.
(See Figure A.)
2. If using the Cartridge Filter (54),
remove the Filter Cover (53). Place
the Cartridge Filter over the Filter
Cage (84). Then replace the Filter
Cover. (See Figure A.)
13. Unlock the Right Latch (34) and Left
Latch (59). Then remove the Upper
Cover (9).
3. If using the Dust Bag (88), place the
Dust Bag over the Filter Cage (84).
(See Figure A.)
(See Figure A, and Assy. Diagram.)
4. Replace the Upper Cover (9), and
lock the Right Latch (34) and Left
Latch (59).
14. If using the Cartridge Filter (54),
remove the Filter Cover (53).
Remove the Cartridge Filter from
the Filter Cage (84). Then replace
the Filter Cover. If necessary, the
Cartridge Filter may be cleaned with
running water. (See Figure A.)
(See Figure A, and Assy. Diagram.)
5. Attach the Suction Hose (50) to the
Intake Port (49). (See Figure A.)
6. Extend the Telescopic Suction Tube
(82), and attach it to the end of the
Suction Hose (50). (See Figure A.)
15. If using the Dust Bag (88), remove
the Dust Bag from the Filter Cage
(84). If necessary, the Dust Bag may
be emptied and cleaned with running
water. (See Figure A.)
7. Attach either the accessory Wet &
Dry Brush (83), Crevice Nozzle (86),
or Furniture Brush (87) to the end of
the Telescopic Suction Tube (82).
(See Figure A.)
16. Replace the Upper Cover (9), and
lock the Right Latch (34) and Left
Latch (59).
8. Plug the Power Cord (11) into the
nearest 120 volt, grounded, electrical
outlet.
(See Figure A, and Assy. Diagram.)
17. Keep the accessories in the
Vacuum’s built-in storage receptacles,
and store the unit in a clean, dry, safe
location out of reach of children and
other unauthorized people.
9. Turn the Power Switch Knob (80) to
its “On” position to start the Wet/Dry
Vacuum. (See Figure A.)
10. Adjust the air flow rate of the Vacuum
by sliding the Air Flow Adjusting Knob
REV 10c
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 9
Wet Vacuuming:
11. IMPORTAnT: The Wet/Dry Vacuum
features Safety Float (63) which will
automatically stops the vacuuming
when the Tank (35) is full (as
1. Unlock the Right Latch (34) and Left
Latch (59). Then remove the Upper
Cover (9).
indicated when the Motor speed
increases). If this happens, turn off
the Switch Knob (80) and unplug the
unit from its electrical outlet. Then
position the Vacuum near a drain,
and drain the dirty water using the
Drain Hose (29). (See Figure A.)
(See Figure A, and Assy. Diagram.)
2. Snap the Foam Filter (85) over
the Filter Cage (84). nOTE: The
Foam Filter must be flush with the
underside of the Upper Cover (9).
(See Figure A.)
12. When finished vacuuming, turn
the Switch Knob (80) to its “OFF”
position. Then unplug the Wet/Dry
Vacuum from its electrical outlet.
(See Figure A.)
3. Replace the Upper Cover (9), and
lock the Right Latch (34) and Left
Latch (59).
(See Figure A, and Assy. Diagram.)
4. Attach the Suction Hose (50) to the
13. Position the Vacuum near a drain,
and drain the dirty water using the
Drain Hose (29). (See Figure A.)
Intake Port (49). (See Figure A.)
5. Extend the Telescopic Suction Tube
(82), and attach it to the end of the
Suction Hose (50). (See Figure A.)
14. Unlock the Right Latch (34) and Left
Latch (59). Then remove the Upper
Cover (9).
6. Attach either the accessory Wet &
Dry Brush (83), Crevice Nozzle (86),
or Furniture Brush (87) to the end of
the Telescopic Suction Tube (82).
(See Figure A.)
(See Figure A, and Assy. Diagram.)
15. Remove the Foam Filter (85) from
the Filter Cage (84). If necessary,
the Foam Filter may be cleaned with
running water. Then clean and dry
the Tank (35) inside and out.
7. Plug the Power Cord (11) into the
nearest 120 volt, grounded, electrical
outlet.
(See Figure A.)
8. Turn the Switch Knob (80) to its
“On” position to start the Wet/Dry
Vacuum. (See Figure A.)
16. Replace the Upper Cover (9), and
lock the Right Latch (34) and Left
Latch (59).
(See Figure A, and Assy. Diagram.)
9. Adjust the air flow rate of the Vacuum
by sliding the Air Flow Adjusting Knob
(67) to the left or right.
17. Keep the accessories in the
Vacuum’s built-in storage
(See Figure A.)
receptacles, and store the unit in a
clean, dry, safe location out of reach
of children and other unauthorized
people.
10. Guide the accessory Wet & Dry
Brush (83), Crevice Nozzle (86),
Furniture Brush (87) with slight
pressure, slowly and evenly, over the
dirty water. (See Figure A.)
REV 10c
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 10
3. Always store the Wet/Dry Vacuum
in a clean, dry, safe location out
of reach of children and other
unauthorized people.
MAInTEnAnCE AnD
SERVICInG
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
4.
WARnInG! If the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
TO PREVEnT
SERIOUS InjURY
WARnInG
FROM ACCIDEnTAL
OPERATIOn:
Turn the Power Switch knob
(80) of the Wet/Dry Vacuum to
its “OFF” position and unplug
the unit from its electrical
outlet before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVEnT SERIOUS
InjURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Cleaning, Maintenance, and
Lubrication
1. BEFORE EACh USE, inspect the
general condition of the Wet/Dry
Vacuum. Check for misalignment or
binding of moving parts, damaged
electrical wiring or hoses, and any
other condition that may affect its
safe operation.
2. AFTER USE, clean all external
surfaces of the unit, inside the Tank,
and all accessories with clean water.
Then dry.
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 11
TROUBLEShOOTInG
Problem
Possible Causes
Likely Solutions
Vacuum will not
start.
1. No power at outlet.
1. Check power at outlet.
2. Cord not connected.
2. Check that cord is plugged in.
3. On/Off switch is not turned On.
3. Turn On the switch.
When dry
vacuuming, Motor
becomes labored.
1. Cartridge Filter is clogged or Tank is
full.
1. Turn off Vacuum, and disconnect the unit from
its electrical outlet. Then clean out Cartridge
Filter and/or Tank.
When wet
1. Tank is full of water.
1. Turn off Vacuum, and disconnect the unit from
its electrical outlet. Then empty the Tank of
dirty water.
vacuuming, unit
automatically stops
vacuuming.
Suction is poor.
1. Insufficient air flow.
1. Adjust Air Flow Adjusting Knob for greater
suction.
2. Insufficient air flow.
2. Make sure all connections are secure.
3. Clean out Hose and accessories.
4. Clean/Replace the filters.
3. Clogged Hose and/or accessories.
4. Inspect the filters.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
PLEASE READ ThE FOLLOWInG CAREFULLY
THE MANUFACTURER AND/OR DISTRIbUTOR HAS PROVIDED THE PARTS LIST AND ASSEMbLy
DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIbUTOR MAkES ANy REPRESENTATION OR WARRANTy OF ANy kIND TO THE bUyER THAT
HE OR SHE IS qUALIFIED TO MAkE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIbUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD bE
UNDERTAkEN by CERTIFIEDAND LICENSED TECHNICIANS, AND NOT by THE bUyER. THE bUyER
ASSUMES ALL RISk AND LIAbILITy ARISINg OUT OF HIS OR HER REPAIRS TO THE ORIgINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 12
PARTS LIST
Part #
1
Description
Decorative Cover
Qty.
1
24
2
3
4
1
1
1
1
1
1
1
4
1
2
1
1
1
2
2
2
1
2
2
2
1
1
1
1
1
1
4
1
1
1
2
4
2
2
2
2
1
1
1
Part #
45
Description
Caster (55mm)
Qty.
2
1
1
1
1
1
2
2
1
1
1
2
2
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2A
3
Screw (ST4.2x16-F)
Upper Cover Pressing Plate
Screw (ST3.5x16-F)
Screw (ST2.9x8-F)
Tool Interface
46
Base
47
Intake Bracket
4A
5A
6
48
Intake Seal
49
Intake Port
50
Suction Hose
7
Tool Interface
51
Pressing Cover Sealing Bar
Sealing Washer B
Filter Cover
8
Upper Cover Interface Plate
Upper Cover
52
9
53
10
11
Connecting Cap (#3)
Power Cord/Plug
Cord Sleeve
54
Cartridge Filter
55
Pressing Plate
12
13A
14
15
16
17
18
19
20
21A
22
23
24
25
26A
27
28
29
30
31
32
33
34
35
36
37A
38
39
40
41
42
43A
44
56A
57
Screw w/Washer (ST4.2x20)
Inner Pressing Plate
Outward Pressing Plate
Left Latch
Screw (ST4.2x13-F)
Middle Cover
58
Exhaust Cover Gasket
Middle Motor Gasket
Handle Sleeve
Upper Handle
59
60
Latch Cover
61
Pressing Plate
62
Upper Cover
Handle Pipe
63
Safety Float
Lower Handle
64
Sealing Washer A
Sealing Cover
Flange Screw (M4x60)
Drain Clip
65
66
Motor bottom Sealing Loop
Air Flow Adjusting Knob
Air Flow Regulator
Motor
Cord Clip
67
Outward Pressing Plate
Inner Pressing Plate
Flange Screw (M4x30)
Drain Cover
68
69
70A
71
Screw (ST2.9x8-F)
Electrical Wiring Pressing Plate
Safety Cover
Drain Cover Strap
Drain Hose
72A
Drain Spring Clip
Drain Tie-In
74
75A
76A
77A
78
Silencing Filter
Screw (ST2.5x13-C)
Exhaust Cover
Screw (St2.5x9.5-C)
Switch
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
Drain Washer
Drain Nut
Right Latch
Tank
79
O-Ring (15x2.65g)
Switch Knob
Wheel Cover
80A
81
Screw (ST2.9x8)
Pin “A” (3.2x20)
Washer (#10)
Handle
82
Telescopic Suction Tube
Wet & Dry Brush
Filter Cage
83
Wheel
84
Axle Bracket
85
Foam Filter
Axle
86
Crevice Nozzle
Furniture Brush
Dust Bag
Screw w/Washer (ST2.9x13-F)
Grounding Chain
87
88
REV 10c
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 13
ASSEMBLY DIAGRAM
A
A
A
A
A
A
A
A
A
A
37A
A
For the following parts, see page 8, Figure A:
Telescopic Suction Tube (82)
Wet & Dry Brush (83)
Filter Cage (84)
Foam Filter (85)
Crevice nozzle (86)
Furniture Brush (87)
Dust Bag (88)
Suction hose (50)
REV 10c
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 14
LIMITED 1 YEAR / 90 DAY WARRAnTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free of defects in materials and workmanship. Harbor
Freight Tools also warrants to the original purchaser, for a period of one year from date
of purchase, that all other parts and components of the product are free from defects in
materials and workmanship (90 days if used by a professional contractor or if used as rental
equipment). This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and
tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons
or property, or for incidental, contingent, special or consequential damages arising from
the use of our product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR
IMPLIED, INCLUDINg THE WARRANTIES OF MERCHANTAbILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 97677
For technical questions, please call 1-800-444-3353.
Page 15
|