7” Desktop FAN
Model 67594
set up AND operAtiNg iNstructioNs
read this material before using this product.
Failure to do so can result in serious injury.
sAVe this MANuAl.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
cord away from traffic area and where it
will not be tripped over.
save this Manual
Keep this manual for the safety warnings
and precautions, assembly, operating,
inspection, maintenance and cleaning
procedures. Write the product’s serial number
in the back of the manual near the assembly
diagram (or month and year of purchase if
product has no number). Keep this manual
and the receipt in a safe and dry place for
future reference.
3. Use only in dry environments. Do not
use in bathrooms, laundry area, near
sinks or other sources of water or
moisture.
4. This product is not a toy. Keep it out of
reach of children.
5. WARNING: Handling cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling.
(California Health & Safety Code §
25249.5, et seq.)
6. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all conditions and
situations that may occur. It must be
understood by operator that common
sense and caution are factors which
cannot be built into this product, but must
be supplied by operator.
speciFicAtioNs
Electrical Requirements 120 V~ / 60 Hz / 22W
Speeds
Low/High
householD use oNlY
uNpAckiNg
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.
SKU 67594
For technical questions, please call 1-800-444-3353.
Page 3
operAtioN
iNspectioN AND
MAiNteNANce
read the eNtire rules For
sAFe operAtioN section at the
beginning of this manual including
all text under subheadings therein
before set up or use of this
product.
to preVeNt
serious iNjurY
FroM AcciDeNtAl operAtioN
or electric shock:
Before appliance inspection or
maintenance, make sure the
appliance’s switch is turned off,
the cord is unplugged, and the
unit has cooled completely.
Back of Fan
Rocker Switch
to preVeNt serious iNjurY
FroM AppliANce FAilure:
Do not use damaged appliances.
if abnormal noise or vibration
occurs, have the problem
Low OFF High
Figure 1
corrected before further use.
1. Set the Rocker Switch to the Off (O)
position.
1. BeFore eAch use, inspect the
condition of the Fan. Check for loose
screws, misalignment or binding of
moving parts, the condition of the electric
wire and its plug, and any other condition
that may affect its safe operation.
2. Place the fan on a flat, stable surface,
routing the power cord to the nearest
outlet, avoiding tripping hazards or strain
on the cord.
2. To facilitate flow of air, clean the fan
3. Plug the cord into the outlet.
blade and grills regularly. To do so:
4. Press the Rocker Switch to the desired
speed:
a. Turn off and unplug the fan. Remove
the five screws from the back of the grill
and gently pry the grills apart.
a. Low (I)
b. High (II)
b. Wash the front grill in mild detergent
and warm water, then wipe dry with a
clean cloth.
5. When finished using the fan, turn the
Rocker Switch to Off (O), unplug the unit
and store in a safe, dry location.
c. Wipe dirt from the blades, rear grill and
electrical cord.
cAutioN: Should the Fan not start when the
unit is plugged in and turned on, or if the
motor “hums” but the fan does not rotate,
immediately turn off and unplug the
fan and have it serviced by a qualified
technician.
d. Re-assemble in reverse order. Allow to
dry completely before reconnecting to
power source.
3. When not in use, store in a safe, dry
location, out of reach of children.
4. This item is pre-lubricated at the factory.
No additional lubrication is required.
Page 4
For technical questions, please call 1-800-444-3353.
SKU 67594
|