®
Models CWA2000 & CWA2000C
WIRELESS MOTION ALERT
Overview
The Wireless Motion Alert uses a Passive Infra-Red (PIR) Motion Sensor to detect movement of people and vehicles, while allowing
small animals to pass through undetected. The Base Station is powered by the AC adapter and the 4 AA batteries supply power in case
of a power outage.
NOTE: The Base Station is intended for indoor use only.
Carton Inventory
Swivel Bushing
Sun/Rain Shield
Mounting Plate
AC Adapter
Base Station
Passive Infra-Red (PIR)
Motion Sensor
Rubber Pads
Operation & Features
BASE STATION
Batteries: If the AC adapter is not connected, the
AA batteries in the Base Station should last up to one week.
If the Base Station batteries are low, the Base Station will
beep every 30 minutes. The AA batteries in the PIR Motion
Sensor will last up to 2 years depending on use (lithium
batteries are recommended for colder environments). If
the PIR Motion Sensor batteries are low, the Base Station
will beep every 30 minutes until the batteries are replaced.
The PIR Motion Sensor will continue to operate with a
low battery, however the light will not illuminate. For peak
performance, inspect batteries annually and replace as
needed.
Antenna
On/Off Button
Volume
Programming Additional PIR Motion Sensors: The Base
Station can learn the code of up to 7 additional PIR Motion
Sensors, responding with unique buzzes. To program
additional PIR Motion Sensors see Step 4.
To order additional PIR Motion Sensors call
1-800-528-9131.
On/Off: To turn the Base Station on and off, hold down the
power button until you hear the on/off tone.
Volume: The Base Station is equipped with adjustable
volume controls. The lowest volume setting is the mute
feature.
Clear Memory: Press and hold the Learn Button on the Base
Station until 3 beeps are heard.
1
Troubleshooting
The PIR Motion Sensor lights up, but the Base Station does
not respond.
The PIR Motion Sensor must be programmed to Base Station
(See Step 4). Ensure Base Station is on and the volume is
turned up.
Base Station beeps every 30 minutes.
The batteries in the Base Station or the PIR Motion Sensor(s)
are low. Replace the 4 AA batteries. Check the PIR Motion
Sensor(s), if the LED illuminates on all of the PIR Motion
Sensors, change the batteries in the Base Station.
PIR Motion Sensor is detecting motion only part of the time.
Ensure the PIR Motion Sensor is set to the High Sensitivity
setting (See Step 2). To detect cars, it is best to mount PIR
Motion Sensor at height of car’s motor and have it between
10-20 feet (3-6 m) from the road. Swivel sensor as needed.
The Alert is not getting expected transmission range.
Keep both antennas vertical and keep PIR Motion Sensor
antenna away from trees and metal objects. Ensure Base Station
is in clearest possible sight of the PIR Motion Sensor. The less
objects between the devices, the longer the range.
The Alert is giving false alarms.
NOTE: The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifications to this
equipment. Changes or modifications not expressly approved
by the manufacturer could void the user’s authority to operate
the equipment.
Check for moving tree branches or insects in sensor window.
PIR Motion Sensor can also be triggered by light shining
directly in sensor window, such as reflected sunlight, or motion
in front of a light source.
It is possible that condensation has built up on the sensor. Wipe
condensation from PIR Motion Sensor with cotton swab. Let it
sit inside for a few hours, open to the air, without the batteries
and it should correct itself.
Check Sensor Switches on PIR Motion Sensor. See Switch
Settings.
3
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
© 2010, The Chamberlain Group Inc.
All Rights Reserved
114A3896D
|