• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws are not loosen.
CAT EYE ENDURO 8
CYCLOCOMPUTER CC-ED300
E: Owner’s Manual
®
Warning
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
• Avoid unnecessary prolonged exposure to the sun. Never at-
tempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
ENDURO8
Important
Note
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002 CAT EYE Co. Ltd.
CCMED3-021210 066600240
1
Please read these instructions carefully before attempting to
install and use your CAT EYE ENDURO 8 computer so that you
understand the functions of this product.
Computer Set-up (For 1st use or after replacing the battery)
Please don’t throw away this manual, Keep the manual at a place easily accessible.
All Clear
Installation of the Computer on Your Bike
1 Push three buttons (MODE, START/
The computer is combined with the following parts.
STOP and SET) at the same time.
* Do this procedure without fail for
stable measurement when you use
this system for the first time and every
time the battery is replaced.
3
3
2
1
4
8
7
SET Button
5
6
7
8
SET Button
Contact Point
START/STOP Button
MODE Button
START/STOP
Button
2
1
1 Bracket
2 Cord
3 Sensor
5 Magnet
MODE Button
You need to know the tire
circumference (L cm) be-
forehand.
6 Bracket Rubber Pad
7 Five Nylon Ties
8 Spiral Tube
Select The Measurement Unit
!
2 Select the measurement unit, kilometer
4 Sensor Rubber Pad
or mile, by pushing the MODE button.
5
Mount the magnet
1
5 on a spoke of the front wheel so that the surface
Sensor Side
Mile
Kilometer
of the magnet will face the sensor.
Spoke
MODE
Choose Either of The Followings.
L cm
• When you want to input the reading of the currently
used odometer, keep pressing the MODE button for
two seconds and input the reading.
• When you want to start the odometer from zero,
push the START/STOP button.
Front Fork
Mount sensor and adjust the gap between the
You can refer to the guide
chart to roughly know the
tire circumference.
2 magnet and the sensor.
Secure the sensor 3 with the larger nylon ties 7 at
the appropriate place and in the right direction.
3
7
Starting the odom- Retaining the current odometer reading
Tire size
L(cm)
eter from zero.
(the odometer starts from the reading you
inputted)
14 x 1.50
14 x 1.75
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
102
106
119
120
134
135
152
162
177
179
175
Front Fork
Important Note
For two seconds.
Marked Line
Mount the sensor 3 at the appropri-
ate position so that the center of the
magnet 5 will align with the
MODE
ST/STOP
Input the current reading of odometer.
5
marked line on the sensor when the
wheel is rotated.
3
24 x 3/4Tubular 178
Increase the
number.
3
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
179
191
189
192
196
192
191
195
195
190
207
210
200
201
202
205
206
207
207
208
217
215
216
216
217
209
212
211
207
208
209
210
211
214
217
216
213
217
218
220
Important Note
MODE
5
Rotate the sensor on the front fork to
adjust the gap between the sensor
and the magnet 5 within 5 mm, and
secure it with the nylon ties.
Move the
decimal point.
26 x 1(59)
26 x 1(65)
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 35A
650 x 38A
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C
Within 5 mm
Center
ST/STOP
Mount The Bracket
3 Secure the cord on the fork with the nylon ties 7 and lead to the handle bar along the outer
SET
cable of the bicycle by means of the spiral tube 8.
Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket 1 until you hear the click sound.
The contact points are automatically closed. When you need to detach the computer, slide
forward the computer with the lever pushed simultaneously.
Note
Set The Tire Circumference
Set the tire circumference in cm.
Note
3
Allow enough wire clearance in the area marked with an
turn the handlebar from left to right without pulling the wire.
to insure that you can
You can easily set it by referring to the chart shown
right.
Setting is completed by pushing the SET button.
1
1
Lever
Increase the
number.
Max. 300 cm
8
6
MODE
1
SET
7
Decrease
the number
Min. 100 cm
Rotate the front wheel.
ST/STOP
Test The Basic Functions
4 Rotate the front wheel gently and see if the computer indicates the
Preparation Complete.
Tire size is usually shown
on the sidewall of tires.
running speed.
OK
(the screen will show the time measurement in this state)
Note
When the computer does not indicate the speed, check
the position of the magnet and the sensor.
* The auto mode is ON in this state.
|