MA1106-EA
Operation Guide 5160
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• All of the displays in this manual show black-on-white.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
E-1
Procedure Lookup
The following is a handy reference list of all the operational procedures contained in
this manual.
Contents
General Guide ......................................................................................................... E-4
Timekeeping Mode .................................................................................................. E-6
About the Backlight .............................................................................................. E-11
Stopwatch Mode ................................................................................................... E-16
Recall Mode ........................................................................................................... E-22
Alarm Mode ........................................................................................................... E-24
Specifications ....................................................................................................... E-27
To set the time and date ......................................................................................... E-8
To set the hands ................................................................................................... E-10
To switch the auto light switch function on and off .......................................... E-13
To measure elapsed time ..................................................................................... E-18
To record a lap time .............................................................................................. E-18
To record a split time ............................................................................................ E-19
To record multiple finishes .................................................................................. E-20
To set the alarm time ............................................................................................ E-24
To stop the alarm .................................................................................................. E-25
To turn a daily Alarm and the Hourly Time Signal on and off ........................... E-26
To test the alarm ................................................................................................... E-26
E-2
E-3
General Guide
• Press B to change from mode to mode.
• If you do not perform any operation for a few minutes while a setting screen (with
flashing digits) is on the display, the watch automatically exits the setting screen.
Timekeeping Mode
Alarm Mode
Stopwatch Mode
Recall Mode
Press B.
E-4
E-5
Timekeeping Mode
Minute hand
Hour hand
• Pressing C in the Timekeeping Mode illuminates the display for about two seconds.
The backlight is disabled while a setting screen is on the display.
• When using 12-hour timekeeping, a P appears on the display for “pm” times (noon
to 11:59 pm). An “am” time (midnight to 11:59 am) is indicated when there is no P
indicator on the display. 24-hour timekeeping is being used when the 24 indicator is
on the display.
Month – Day
Day of week
Second hand
PM indicator
Hour
Seconds
Minutes
E-6
E-7
To set the time and date
DST indicator 2
DST indicator 2
1. While in the Timekeeping Mode, hold down A until the seconds digits flash on the
display, indicating the setting screen.
2. Press B to move the flashing in the sequence shown below.
DST indicator 1
DST indicator 1
Seconds
Day
DST
Hour
Year
Minutes
12/24
Month
Press C.
3. While the seconds setting is selected (flashing), press C to reset it to 00.
• If you press C while the seconds setting is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00
to 29, the minutes count is unchanged.
DST OFF
DST ON
• DST indicator 1 flashes on the display only while the DST setting is selected on the
setting screen. It shows 0 when DST is turned off, and 1 when DST is turned on.
• DST indicator 2 also flashes on the display while the DST setting is selected on the
setting screen. In addition, it appears in the Timekeeping Mode and Alarm Mode
while DST is turned on. DST indicator 1 is not displayed in these modes while DST
is turned off.
∗
• While the DST (Daylight Saving Time) setting is selected, press C to toggle it on
and off.
∗ Daylight Saving Time (DST), which is also sometimes called “summer time”
advances the time for one hour, as is the custom in some areas during the summer.
Remember that not all countries or even local areas use Daylight Saving Time.
E-8
E-9
Operation Guide 5160
• The first nine split times you record are stored in
3. Press C as each runner finishes. The finish time and
1/100 second
Seconds
Minutes
1/100 second
Seconds
Minutes
memory. The final time you record when you press A is
also stored, for a total of 10 times.
sequence number remains on the display for about
seven seconds. Stopwatch timing continues internally.
• The first nine split times (finish time) you record are
stored in memory. The final time you record when you
press A is also stored, for a total of 10 times.
•
If you continue to perform the split time operation after
there are already nine times in memory, the split times
are shown on the display but are not stored into memory.
• You can perform up to 99 split time operations (9 stored
+ 90 unstored) during each elapsed time operation.
• You can recall split times using the Recall Mode.
4. Press A to stop the time measurement.
•
If you continue to perform the split time operation after
there are already nine times in memory, the split times
are shown on the display but are not stored into memory.
• You can perform up to 99 split time operations (9 stored
+ 90 unstored) during each elapsed time operation.
• You can recall split times using the Recall Mode.
4. Press A to stop the time measurement.
5. Press C to clear the stopwatch to all zeros.
To record multiple finishes
1. In the Recall Mode, use A to select split time as the
timing operation.
• See “Recall Mode” for more information about selecting
the stopwatch operation.
5. Press C to clear the stopwatch to all zeros.
Split number
SPL indicator
Sequence number
2. Enter the Stopwatch Mode, and then press A to start
the stopwatch.
E-20
E-21
1/100 second
Recall Mode
1/100 second
Seconds
Minutes
Seconds
Minutes
Use the Recall Mode to recall the lap times and split times stored in memory.
• Press A to toggle the display between lap times and split times.
• Press C to scroll through Recall Mode records.
Starting a new elapsed time operation in the Stopwatch Mode automatically clears the
data (lap or split) that is currently displayed in the Recall Mode.
Lap number
Split number
LAP indicator
SPL indicator
[SPLIT time display]
[LAP time display]
E-22
E-23
3. Press C to increase the selected digits. Holding down C changes them at high
speed.
4. After you make the settings you want, press A to exit the input screen.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
Alarm Mode
When a Daily Alarm is turned on, the alarm sounds for
Mode indicator
Minutes
about 20 seconds at the preset time each day. Press any
button to stop the alarm after it starts to sound. When the
Hour
Hourly Time Signal is turned on, the watch beeps every
hour on the hour.
To set the alarm time
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
1. Hold down A while in the Alarm Mode, until the hour
digits starts to flash on the display, indicating the setting
screen. The alarm is automatically turned on at this
time.
2. Press B to change the selection in the sequence
shown below.
Current time
Daily Alarm indicator
Hour
Minutes
Hourly Time Signal
indicator
E-24
E-25
To turn a daily Alarm and the Hourly Time Signal on and off
Specifications
Accuracy at normal temperature: 30 seconds a month
3-hand: Hour, minute, second
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Timekeeping Mode: Hour, minutes, seconds, am/pm(P), month, day, day of the week
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Full auto-calendar pre-programmed from 2000 to 2099
Standard time/Daylight saving time
Both OFF
Daily Alarm
Only
Hourly Time
Signal Only
Both ON
Stopwatch Mode
To test the alarm
Measuring unit:1/100 of a second (up to 59' 59" 99)
1 second (from 1:00' 00")
Hold down B in any mode (except when making any settings) to sound the alarm.
Measuring capacity: 9 hours, 59 minutes, 59 seconds
Functions: Elapsed time, lap time and split time
Memory: 10 records (laps, splits)
Note that this operation also changes the mode.
Alarm Mode: Daily alarm, hourly time signal
E-26
E-27
EL backlight: Automatic, manual
Battery: One lithium battery (Type: CR2016)
Battery life: 3 years under the following conditions
• 2-second backlight operation per day
• 20-second alarm operation per day
E-28
|