Casio Watch MA0504 EA User Manual

MA0504-EA  
Operation Guide 4333  
Stopwatch minute hand  
Minute hand  
To set the time  
1. Pull out the crown to the second  
click.  
Hour hand  
This causes the second hand to  
First click  
(Day setting)  
stop.  
2. Set the hands by rotating the crown.  
Move the minute hand four or five  
minutes past the time you want to  
set, and then back it up to the proper  
setting.  
3. Push the crown back in to the  
normal position to restart  
timekeeping.  
Second click  
(Time setting)  
Stopwatch  
second  
hand  
Day  
Second  
hand  
Crown  
(Normal position)  
To set the day  
1. Pull out the crown to the first click.  
2. Set the day by rotating the crown.  
3. Push the crown back in to the normal position.  
Avoid setting the day between 9:00 p.m. and 1:00 a.m. (the day display may not  
change in the following day).  
Using the Stopwatch  
The stopwatch lets you measure elapsed time up to 59 minutes, 59 seconds. You  
can also correct the position of the stopwatch second hand when necessary.  
The illustration shows a time of 20 minutes, 40 seconds.  
Do not try to perform stopwatch operations while the crown is pulled out either to  
the first or second click. If you try to press a button, you might accidentally cause  
the crown to rotate and change the current time or day setting.  
To measure elapsed time  
1. Press A to start the stopwatch.  
2. Press A to stop the stopwatch.  
You can resume the measurement operation by pressing A again.  
3. Press B to reset the stopwatch.  
Adjusting the Stopwatch Second and Minute Hand Positions  
Use of the stopwatch can cause the starting positions of the stopwatch minute hand  
and second hand to become misaligned. Use the following procedures to check hand  
alignment and to adjust the positions of the hands so they point to 12 o’clock when  
the stopwatch is reset.  
To adjust the positions of the stopwatch hands  
1. Press B to reset the stopwatch, and check the alignment of the stopwatch minute  
hand and second hand.  
2. Pull out the crown to the second click.  
3. Press A to move the stopwatch second hand forward until it points to 12 o’clock.  
4. If the stopwatch minute hand is aligned correctly, proceed to step 5. If the  
stopwatch minute hand is also misaligned, press B so the stopwatch minute hand  
jumps to 0.  
5. After making the adjustments you want, push the crown back in to its normal  
position.  
Note that pulling the crown out also stops the timekeeping second hand. After  
performing the above procedure, you should also adjust the timekeeping setting.  
I For watch with the elapsed time bezel  
Rotate the elapsed time bezel to align the  
minute hand.  
After certain amount of time elapsed, read the graduation on the  
elapsed time bezel which the minute hand points to.  
The elapsed time is indicated.  
10  
mark with the  
50  
2 0  
4 0  
3 0  
Elapsed time bezel  
Some water resistant models are equipped with a screw lock  
crown.  
With such models, you must unscrew the crown in the direction  
noted in the illustration to loosen it before you can pull it out.  
Do not pull too forcibly on such crowns.  
Also note that such watches are not water resistant while their  
crowns are loosened. Be sure to screw the crowns back in as  
far as they will go after making any setting.  
1
 

Black Decker Coffeemaker DCM100BC User Manual
Braun Trimmer EN 10 User Manual
Briggs Stratton Portable Generator 30324 User Manual
Briggs Stratton Power Supply 071013 User Manual
Brother Sewing Machine XL2600I User Manual
Canon Scanner iR Series User Manual
Casio Digital Camera EX Z28 User Manual
Casio Watch MA0606 EA User Manual
CDA Ventilation Hood CCA5 7 User Manual
Char Broil Charcoal Grill 463460712 User Manual