MO0212-A
USER’S GUIDE 2619
About This Manual
• Normally, your watch should show the correct time as soon as you select your Home
• The display of this watch uses two LCD panels that
make it possible to display icons, numbers formed with
segments, dot matrix characters, etc.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night).You can also perform manual receive (see “To
perform manual receive”) or you can set the time manually (see “Setting the Time
and Date Manually”).
(Light)
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting (see “To change the Daylight Saving Time (summer time) setting”).
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch automatically picks up the time calibration signal three
times a day at 2:00 AM, 4:00 AM, and 5:00 AM. For more information, see “About Auto
Receive.”
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive.”
General Guide
Icons
No matter what type of operation you want to perform with
this watch, the first step is always to select the proper
mode. Use the Mode Menu screen to select a mode.
• The Mode Menu screen shows icons for each of the
modes.
Important!
• Position the watch as shown in the nearby illustration, with its 12 o’clock side facing
towards a window. Make sure there are no metal objects nearby.
• Holding down A while the Mode Menu screen is on the
display replaces the current time with the current date.
To change modes
1. While the Mode Menu screen is on the display, press
B or D.
• This causes one of the icons on the screen to flash.
• If another screen is on the display, press C to display
the Mode Menu screen before performing the above
step.
Seconds
Hour : Minutes
Resin
Metal Band
Band
Hold
downA.
• The flashing stops if you do not perform any operation
for about 10 seconds after performing the above step.
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
Day of week
Month – Day
2. While an icon is flashing on the Mode Menu screen, use B and D to move it to
the icon whose mode you want to access.
• The following shows the name of the mode that corresponds to each icon.
Press D.
Press B.
Inside a
vehicle
Near
Near a
construction
site, airport, or power lines
other sources
of electrical
Near high-
tension
Among or
behind
mountains
Inside or
among
buildings
Icon
Mode
Icon
household
appliances,
office
equipment,
or a mobile
phone
Timekeeping
World Time
e-DATA MEMORY
noise
Alarm
Signal Receive
Time Memo
Stopwatch
Recall
Mode
Icon
• Signal reception is normally better at night than during the day.
• Time calibration signal reception normally takes from two to six minutes. In Japan,
however, reception can take up to 12 minutes. Take care that you do not perform any
button operations or move the watch during this time.
Remaining Memory
Mode
• When within range of the applicable transmitter, this watch can receive either
Continental U.S. (Fort Collins, Colorado) or Japanese (Fukushima or Fukuoka/Saga)
time calibration signals. The signal the watch will attempt to pick up depends on its
current Home City code setting as shown below.
*
The
(REMAIN) icon simply shows remaining time
Timekeeping Mode
*
memo memory, without changing to another mode.
Because of this, the
details about the
icon does not flash. For
icon, see “To recall time memos.”
Home City Code
Transmitter
Fort Collins, Colorado
Fukushima
Frequency
60kHz
3. Press C to enter the mode whose icon is flashing.
,
LAX DEN CHI NYC
,
,
• Simply pressing C while the
(MEMO: Time Memo
Hour :
Minutes
Mode) icon is flashing does not enter the Time Memo
Mode. See “Time Memo” for more information.
• After entering any mode, you can return to the Mode
Menu screen by pressing C again.
40kHz
TYO*
Fukuoka/Saga
60kHz
Day of week
With
Frequencies”).
, you can specify either 40kHz or 60kHz (see “Japan Signal
TYO
*
• In any mode and while the Mode Menu screen is on the
display, press L to illuminate the display.
500
kilometers
2,000 miles
600 miles
500
kilometers
Fukushima
Fukuoka/Saga
Seconds
Year Month – Day
1,000
kilometers
1,000
kilometers
Fort Collins
Radio-controlled Timekeeping
• Under good reception conditions, signal reception is possible within a radius of
about 2,000 miles (3,000 kilometers) from the Fort Collins transmitter.
• At distances further than about 600 miles (1,000 kilometers) from the Fort Collins
transmitter, the signal may become weak and reception may be impossible under
certain conditions.
• At distances further than about 500 kilometers from the Fukushima and Fukuoka/
Saga transmitter, the signal may become weak and reception may be impossible
under certain conditions.
This watch is designed to pick up a time calibration signal and updates its time setting
accordingly. The time calibration signal includes both Standard Time and Daylight
Saving Time (summer time) data.
• When within range of the applicable transmitter, this watch can receive either
Continental U.S. or Japanese time calibration signals.
Current Time Setting
• See the information under “Signal Receive Troubleshooting” if you experience
problems with time calibration signal reception.
This watch automatically adjusts its time setting in accordance with a time calibration
signal.You can also perform a manual procedure to set the time and date, when
necessary.
About Auto Receive
• The first thing you should do after purchasing this watch is to set your Home City,
which is the city where you will normally use the watch. For more information, see
“To set your Home City” below.
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the time in the Timekeeping Mode reaches 2:00 AM, 4:00 AM,
and 5:00 AM each day (calibration times).
• See “Timekeeping” for information about manual settings.
Note
To set your Home City
• The watch performs auto receive only if Mode Menu screen is on the display, or if
the watch is in the Timekeeping Mode, or World Time Mode when one of the
calibration times is reached. Auto receive is not performed if a calibration time is
reached while an alarm is sounding, or while you are configuring settings (while
settings are flashing on the display).
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can easily receive the signal.
• When auto receive is turned on, the watch receives the calibration signal for two to six
minutes everyday when the Timekeeping Mode reaches each of the three calibration
times. Do not perform any button operation within six minutes before or after any of the
three calibration times. Doing so can interfere with correct calibration.
1. Enter the Timekeeping Mode.
2. Hold down A until the seconds start to flash, which
indicates the setting screen.
3. Press C twice so the current city code is flashing.
4. Use D (east) and B (west) to scroll through the city
codes until the one you want to use as your Home City
is displayed.
• The following are the city codes for major cities in the
Continental United States time zones and in Japan.
: Los Angeles, San Francisco, Las Vegas,
LAX
l
l
Seattle
l
: Denver, El Paso
DEN
: Chicago, Houston, Dallas/Fort Worth, New
CHI
Orleans
: New York, Detroit, Miami, Boston
NYC
: All cities in Japan
TYO
5. Press A to exit the setting screen.
1
USER’S GUIDE 2619
• The 10 segments of the remaining memory graphic indicate how much memory is
To create a new e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, press B and D at the
left for storage of time memos. The 10 segments of the Remaining Memory icon (
on the Mode Menu screen also indicate remaining memory capacity.
)
same time to display the New Record screen.
• If the New Record screen does not appear, it means
that memory is full. To store another record, you will
first have to delete some of the records stored in
memory.
100 – 90 records
89 – 80 records
79 – 70 records
0 record
• The remaining memory graphic is also displayed in the Timekeeping Mode.
2. Hold down A until the flashing cursor ( ) appears on
the display, which indicates the setting screen.
• The setting screen also shows the record number that
is automatically assigned to the new record.
3. Input the text.
• Use D to cycle through characters at the cursor
position, and then press C to move the cursor to the
right. See “Inputting Text” for more information.
4. Press A to store your data and return to the e-DATA
MEMORY record screen (without the cursor).
• Pressing A causes the word SORTto appear for a
moment as the data is stored. After that, the e-DATA
MEMORY record screen appears.
• The text can show only five characters at a time, so
longer text scrolls continuously from right to left.
Scrolling pauses for about one second when the end of
the text is reached.
• Note that the record number of a particular record may
change when records are resorted after input of a new
record.
• Creating a time memo while memory is full deletes the oldest time memo and stores
the new one.
New Record Screen
To input time memo text
1. In the Recall Mode, use D (+) and B (–) to scroll
through the time memos and display the one where you
want to input text.
Cursor
2. Hold down A until the flashing cursor appears on the
display.
3. Input the text.
• You can input up to eight characters for the text.
• Use D to cycle through characters at the cursor
position, and then press C to move the cursor to the
right. See “Inputting Text” for more information.
4. After inputting your text, press A to store it.
• Pressing A causes the word
to appear for a
moment as the data is stored. After that, the time memo
appears.
SAVE
• The text can show only five characters at a time, so
longer text scrolls continuously from right to left.
Scrolling pauses for about one second when the end of
the text is reached.
• To edit text, perform steps 1 and 2 of the above
procedure, move the cursor to the location of the text
you want to edit, and then input the text you want.
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use D (+) and B (–) to cycle through e-DATA
MEMORY records as shown below.
Press D.
New
Password
Setting
To delete a time memo
1. In the Recall Mode, use D (+) and B (–) to scroll through time memos and display
the one you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the time memo.
Record 1
Record 2
Record
screen
screen
Press B.
• The Password Setting screen is the one with the words SETPASS on it.
• You can use the Password Setting screen to register, edit, or delete your password.
See “Using a Password to Protect e-DATA MEMORY Data” for more information.
• The word
appears to indicate that the time memo is being deleted. The
CLEAR
Time Memo screen appears after the record is deleted.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
World Time
World Time shows the current time in 30 cities (29 time
zones) around the world.
City code
• All of the operations in this section are performed in the
World Time Mode, which you can enter from the Mode
Menu screen.
To view the time in another city code
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record you
want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The word CLEARappears to indicate that the record is being deleted. After the
record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the New Record screen.
In the World Time Mode, press D to scroll through city
codes (time zones) to the east or B to scroll to the west.
• For full information about city codes, see the “City Code
Table.”
• If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
Timekeeping Mode time
Current time in the zone of
the selected city code
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others to
decipher. If you forget the password, you will have to have your watch initialized (which
returns all time settings to their initial factory defaults) in order to access the e-DATA
MEMORY again. To have the watch initialized, contact the store or dealer where you
purchased it, and ask to have the AC operation performed.
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while GMTis selected as the
city code.
To register a new password
1. In the e-DATA MEMORY Mode, use D (+) and B (–)
to display the Password Setting screen.
• This displays a screen that shows SETPA55.
2. Hold down A for about two seconds until the first
(leftmost) digit of the password starts to flash.
• This is the New Password Setting screen.
3. Use D (+) to scroll through numbers at the first digit.
4. When the first digit is the number you want, press C to
advance to the next digit.
5. Repeat steps 3 and 4 to input all four digits of the
password you want.
e-DATA MEMORY
6. After all four of the password digits are the way you
want, press C to register them and return to the
Password Setting screen.
• Make sure you press C to return to the Password
Setting screen after inputting all four digits.
• After registering a password, you can input, recall, edit
and delete data, if you want. After you exit the e-DATA
MEMORY Mode, you will have to input the password
every time you want to enter the e-DATA MEMORY
Mode again.
You can use the watch’s e-DATA MEMORY to store e-mail
Record number addresses, Web page URLs, and other text data.You can
Text
store up to 100 records, and even use a password to limit
access to e-DATA MEMORY contents.
• You can input up to 63 characters for the text of each
record.
• Records are stored in alphabetical order. See “Character
List” for details on how the watch sorts records.
• All of the operations in this section are performed in the
e-DATA MEMORY Mode, which you can enter from the
Mode Menu screen.
To input the password
• If
PA55 appears when you try to enter the
e-DATA MEMORY Mode, perform the procedure under
“To input the password.”
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen (
PA55), press
Timekeeping Mode time
D. This causes the first digit of the password to flash.
3. Input the password.
Maximum memory
capacity (100 records)
• Input the password you registered or
.
0000
• Use D (+) to scroll through numbers at each digit.
• Press C to advance to the next digit.
4. After the password is the way you want, press C.
• If the input password matches the one registered, the
word OK!appears, followed by an e-DATA MEMORY
screen.
• If the password does not match, the word ERRORappears, followed by the
Password Input screen.
• If you want to be able to access e-DATA MEMORY without inputting a password,
delete the password using the procedure under “To delete the password.”
• If you make a mistake part way through inputting the password, press C to scroll
past the remaining digits. This will cause a password input error, after which you can
re-input the password.
3
USER’S GUIDE 2619
To change the password
To turn the Hourly Time Signal on and off
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Perform the procedure starting from step 2 under “To register a new password” to
specify the new password.
1. In the Alarm Mode, use D to select the Hourly Time
Signal (:00).
2. Press A to toggle it on (SIG displayed) and off (SIG
not displayed).
• The Hourly Time Signal on indicator (SIG) is shown on
the display in all modes (except the Recall Mode) while
the Hourly Time Signal is turned on.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Hold down A for about two seconds until the first (leftmost) digit of the password
starts to flash.
4. Press B and D at the same time to delete the password.
• The word CLEARappears to indicate that the password is being deleted. After
the password is deleted, the Password Setting screen appears.
Hourly time signal
on indicator
Alarms
Stopwatch
The stopwatch lets you measure elapsed time.
• The display range of the stopwatch is 23 hours, 59
minutes, 59 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you can enter from the Mode
Menu screen.
You can set five independent Daily Alarms. When an
Alarm time
(Hour : Minutes)
alarm is turned on, the alarm tone sounds when the
alarm time is reached. One of the alarms is a snooze
alarm, while the other four are one-time alarms. You can
also input reminder text.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• You can input up to eight characters for the reminder
text.
• There are five alarm screens numbered 1 through 4 for
the one-time alarm, and a snooze alarm screen
indicated by Sn. The Hourly Time Signal screen is
indicated by :00.
Seconds
• All of the operations in this section are performed in the
Alarm Mode, which you can enter from the Mode Menu
screen.
Timekeeping
Mode time
Minutes
1/100 second
To measure elapsed time
Alarm number
1. Press D to start the stopwatch.
2. Press D to stop the stopwatch.
To set an alarm time
Hours
Minutes
• You can resume the measurement operation by
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
pressing D again.
• For the first 60 minutes, the screen shows minutes,
seconds, and 1/100 second. After 60 minutes, the
screen format changes to show hours, minutes, and
seconds.
x1
x2
Sn
x3
x4
:00
3. Press B to clear the stopwatch to all zeros.
• To set a one-time alarm, display one of the screens
indicated by an alarm number from x1 through x4. To
set the snooze alarm, display the screen indicated by Sn.
• The snooze alarm repeats every five minutes.
Seconds
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other
settings.
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date. This section also explains how to manually
set the current date and time.
• All of the operations in this section are performed in the
Timekeeping Mode, which you can enter from the Mode
Menu screen.
Hour : Minutes
Day of week
Hour
Minutes
Text
• Selecting the text causes the text input cursor ( ) to appear. There are eight
spaces in the text, so you have to press C eight times to move to the Hour
setting.
4. When the setting you want to change is selected, press D to change it.
• While the hour or minute setting is flashing, press D (+) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
• When inputting text, press D to cycle through characters at the current cursor
location, and C to move the cursor to the right. See “Inputting Text” for more
information.
• Pressing B and D at the same time while any setting is flashing automatically
sets the time to AM12:00. It also clears any text that is input for the alarm.
5. Press A to exit the setting screen.
• The text you input appears at the top of the display screen. If the reminder text is
more than five characters, it will scroll from right to left. Scrolling pauses for about
one second when the end of the text is reached.
Setting the Time and Date Manually
Note that all of the World Time Mode times are displayed
in accordance with the Home City code (the code for the
city where you normally use the watch) that you select in
the Timekeeping Mode.
• Once you correctly set your Home City time and date,
you can set the watch up for timekeeping in another time
zone by simply changing the Timekeeping Mode Home
City code.
PM
indicator
Seconds
Year Month – Day
To set the current time and date manually
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B and D to select the code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table.”
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• To stop the alarm tone after it starts to sound, press any button.
• If you input reminder text for an alarm, the text appears for one minute on the
Timekeeping Mode screen when the alarm time is reached.You can clear the
reminder text display by exiting the Timekeeping Mode.
3. Press C to move the flashing in the sequence shown
below to select the other settings.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Home City
Code
12/24-Hour
Format
Seconds
Day
DST
Displaying the SNZsetting screen
Hour
Month
Year
Minutes
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
4. When the setting you want to change is flashing, use B and D to change it as
To turn an alarm on and off
described below.
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
Screen
To do this:
Do this:
• Turning on a one-time alarm (1 through 4) displays the
alarm on indicator (ALM) on its Alarm Mode screen.
Turning on the snooze alarm (Sn) displays the alarm on
indicator and snooze alarm indicator (SNZ) on its Alarm
Mode screen.
• In all modes (except the Recall Mode), the alarm on
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
50
Reset the seconds to 00
Press D.
Toggle between Daylight Saving Time (ON),
Standard Time (OFF), or Auto DST (AUTO)
AUTO
NYC
Press D.
Change the Home City code
Use D (east) and B(west).
Press D.
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
12H
P10:58
Change the hour or minutes
Press D (to increase).
Press D (to increase).
Alarm on
indicator
Snooze alarm
indicator
03 6-30 Change the year, month, or day
• Auto DST (AUTO) can be selected only while HNL, ANC, LAX, DEN, CHI,
NYC, TYO, SEL, or HKGis selected as the Home City code. For more
information, see “Daylight Saving Time (DST)” below.
5. Press A to exit the setting screen.
4
USER’S GUIDE 2619
• Though this watch is designed to receive both time data (hour, minutes, seconds)
Daylight Saving Time (DST)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
• When all three auto receptions are successful (2:00 AM, 4:00 AM, and 5:00 AM), the
watch uses the data of the last reception for calibration. When only one reception is
successful, the watch uses the data of the successful reception.
• Normally, the signal reception date shown by the Last Signal screen is date data that
is included in the received time calibration signal. When only time data is received,
however, the Last Signal screen shows date as kept in the Timekeeping Mode at the
time of signal reception.
The time calibration signal transmitted from Fort Collins, Colorado includes both
Standard Time and DST data. When the auto DST setting is turned on, the watch
switches between Standard Time and DST (summer time) automatically in
accordance with the Fort Collins signal.
• The time calibration signals transmitted from the Fukushima and Fukuoka/Saga do
not include summer time data.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within ±15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code and DST
(summer time) settings, and auto receive setting. The following are the initial factory
defaults for these settings.
• The auto DST setting can be turned on only while HNL, ANC, LAX, DEN,
CHI, NYC, TYO, SEL, or HKGis selected as the Home City code.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
Setting
City code
Initial Factory Default
NYC (New York)
DST (summer time) AUTO(Auto switching)
2. Press C to display the DST setting screen.
3. Press D to cycle through the DST settings in the
sequence shown below.
Auto receive
On
(Auto receive)
Japan Signal Frequencies
When you have
(Tokyo) selected as the Home City code, you can use the
TYO
Auto DST
(AUTO)
DST Off
(OFF)
DST On
(ON)
following procedure to specify either 40kHz or 60kHz as the reception frequency. The
frequency you should use depends on your current location in Japan. See the map
under “Important!” for more information.
4. Press A to exit the setting screen.
To select a frequency for use in Japan
• The DST indicator appears on the display to indicate
1. Enter the Signal Receive Mode.
2. Hold down A until
that Daylight Saving Time is turned on.
appears, with the receiving
FREQ.
indicator (Level 4) flashing. This is the setting screen.
3. Use D to select the frequency you want to use.
• Each press of D cycles through the available
frequencies as described below.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
40:60
:
The watch automatically selects the
frequency that has the strongest signal.
Receives the signal from Fukushima (40kHz).
Receives the signal from Fukuoka/Saga
(60kHz).
40
60
:
:
Auto Display
Auto Display continually changes the contents of the
digital display.
4. Press A to exit the setting screen.
• Reception can take up to 12 minutes when the
option is selected.
Frequency
40:60
To turn off Auto Display
Press any button to turn off Auto Display.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
To turn on Auto Display
While the Mode Menu screen is on the display, press A
and C at the same time.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
Inputting Text
The following describes how to input text in the Recall Mode, e-DATA MEMORY and
Alarm Modes.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Greenwich Mean Time (GMT) differential for each
city, based on your Home City time setting.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC*) data.
To input characters
1. When the cursor is on the display, press D to cycle
through the available letters, numbers and symbols, in
the sequence shown below.
Cursor
* The letters “UTC” stands for “Universal Time Coordinated,” which is the world-wide
scientific standard of timekeeping. It is based upon carefully maintained atomic
(cesium) clocks that keep time accurately to within microseconds. Leap seconds
are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation. The reference point for UTC is Greenwich, England.
a to z
(lower-case)
Ato Z
(upper-case)
(space)
to )
(symbol)
0to 9
(number)
2. When the character you want is at the cursor position,
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Recall Mode
press C to move the cursor to the right.
3. Repeat steps 1 and 2 to input the rest of the characters you want.
• See the “Character List” for information about the characters you can input.
Auto Return Features
• If you leave the watch without performing any operation in the Signal Receive,
Recall, e-DATA MEMORY, or Alarm Mode for two or three minutes, it automatically
changes to the Mode Menu screen.
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically exits the setting
screen.
Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. In any mode, press L to illuminate the display for
about one second.
• The electro-luminescent panel that provides illumination loses power after very long
Scrolling
use.
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the life of the battery.
Initial Screens
When you enter the e-DATA MEMORY, World Time, or Alarm Mode, the data you were
viewing when you last exited the mode appears first.
Time Calibration Signal Reception Precautions
Battery
• Signal reception is terminated if any alarm starts to sound while reception is being
The indicator BATT flashes on the display any time
battery power is below a certain level. Low battery power
can cause the following conditions to occur.
• Dim, difficult-to-read display characters
• Failure of the backlight and beeper tone operations
performed.
• Strong electrostatic charge can result in the wrong time being set.
• Even when the watch is within the reception range of the transmitter, signal
reception is impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• The time calibration signal is bounced off the ionosphere. Because of this, such
factors as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
l
l
l
• Inability to perform time calibration signal reception
• Inability to create a time memo, or to perform Recall
Mode, and e-DATA MEMORY Mode operations
l
l
l
l l
l
l
l
l
l
l
If battery power goes low while you are inputting Time Memo, e-DATA MEMORY, or
alarm text data, the data you are inputting may not be saved in memory. Normal watch
operation will return after the BATT indicator disappears. If it does not disappear, have
the battery replaced.
Always leave battery replacement up to the dealer where you bought the watch or
to an authorized CASIO distributor. Be sure to show the “Attention dealer or CASIO
distributor” information to the person replacing the battery.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
• The watch is designed to automatically update the date and day of the week for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
5
USER’S GUIDE 2619
Indicator
If you use the backlight or any of the alarm functions a number of times during a short
period,
appears at the top of the display screen, and the following operations
become disabled until battery power recovers.
Backlight; Beeper tone; Time calibration signal reception; Time memo creation
operation; Recall and e-DATA MEMORY Mode operations
• After some time, battery power will recover and
will disappear, indicating
that the above functions are enabled again.
• The word
appearing on the display when you try to perform a time memo
ERROR
operation or an e-DATA MEMORY Mode operation indicates that the watch cannot
access its memory because battery power is momentarily too low.
ERROR
changes to
after about two or three minutes, or if you press C.
• If battery power cannot recover sufficiently within about 10 minutes after the
indicator appears, the BATT indicator is displayed to let you know that
battery power is low.
Attention dealer or CASIO distributor
1. Open and remove the back cover.
• Opening the back cover causes the word OPENto appear on the display.
• If CLOSEappears on the display when you open the back cover, replace the
back cover. Wait for a few minutes and try again.
2. Remove the battery holder.
3. Remove the old battery and load a new one.
4. Touch the AC contact and the battery [+] side with metal tweezers.
• The AC (all clear) operation DOES NOT delete time memos and e-DATA
MEMORY Mode data stored in memory.
5. Replace the battery holder.
6
|