IP Router
QUICK START GUIDE
Part Number: 002-0118-0180
Product Release: 1.8
May 2004
QUICK START GUIDE
n Basic Setup
Routing
Address Routing
Firewall Filters
Addresses
n Back-to-Back with PPP
n Back-to-Back with Multi-Link PPP
n Back-to-Back with Frame Relay
Quick Start Guide
Installation
Installation
Installation of the router card into the chassis.
l Unit can be on or off
l Router card will work in any slot
l Slide card into slot until fully seated
l Router has completed it’s boot cycle when CRD light is solid
The following setups are all executed with CLI
NOTE: Configuration can be done with the following CLI commands or
with the Router Menu-Driven Software.
Basic Setup
Command
Description
set {ds0-addr} type data
Confirm DS0 is set to type data.
ds0-addr = {slot:port:channel} of DS0
Example: set a:1:1-24 type data
connect {slot:port:trunk}
{slot:port:channel}
Cross-connect T1 to router card.
Example: connect a:1:1-24 6:1:1 (router in slot 6)
set {router-addr} proxy
Disable/enable router proxy.
router-addr = {slot:port}| of router card.
Example: set 6:1 disable.
set {slot:port} up
Set Router LAN as In-Service. Example: set 6:1 up
telnet {router_card-addr}
Telnet to Router card.
router_card-addr = {slot} location of router card
Example: telnet 6 (if earlier than 3.0 release {slot:port} must
be used)
Local and Remote Profile Setup
reinitialize
To enable any configuration changes, the card must be
reinitialized.
4
IP Router - Release 1.8
Quick Start Guide
PPP Internet Connection and Public IP Address Routing
PPP Internet Connection and
Public IP Address Routing
Router in Slot 1
ISP Router that provides the Internet connection.
Command
Description
set clock1 a:1
set 1 default
disconnect a:1
Set primary master transmit clock source
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the from "LocalUnit" (default) to
"Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 215.168.21.14
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
add 1 "wan1" static ip network
0.0.0.0 0.0.0.0 1
Adds a static IP network (route) to the WAN
interface
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
reset 1
Reboot the router, to enable all configurations set
IP Router - Release 1.8
5
Quick Start Guide
Frame Relay Internet Connection and Public IP Address Routing
Frame Relay Internet Connection and
Public IP Address Routing
Router in Slot 1
ISP Router that provides the Internet connection.
Command
Description
set clock1 a:1
set 1 default
disconnect a:1
Set primary master transmit clock source
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the from "LocalUnit" (default) to
"Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 215.168.21.14
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
add 1 "wan1" static ip network
0.0.0.0 0.0.0.0 1
Adds a static IP network (route) to the WAN
interface
set 1:1:1 encapsulation fr
set 1 lmi annexd
Set the encapsulation on trunk 1 to Frame Relay
Disable LMI to Annex D
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
set 1 "wan1" dlci 101
reset 1
Set the DLCI number
Reboot the router, to enable all configurations set
6
IP Router - Release 1.8
Quick Start Guide
Internet Connection using PPP, NAT/PAT and Firewall Filters
Internet Connection using PPP, NAT/PAT and
Firewall Filters
Router in Slot 1
ISP Router that provides the Internet connection. Router with NAT/PAT and Firewall
Filters.
Command
Description
set clock1 a:1
set 1 default
disconnect a:1
Set primary master transmit clock source
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the from "LocalUnit" (default) to
"Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 192.168.21.14
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
set 1 "wan1" nat enable
Set the WAN interface named "wan1" enable
NAT mapping
set 1 "wan1" nat address
216.174.44.2 1
Set the WAN interface named "wan1" NAT
address
add 1 "wan1" static ip network
0.0.0.0 0.0.0.0 1
Adds a static IP network (route) to the WAN
interface
add 1 "wan1" firewall 1 pass
incoming log telnet
192.168.21.14/32
Adds a Firewall rule to the WAN. Where
xxx.xxx.xxx.xxx is the host’s IP address at the far
end that will be able to ping or telnet to the router.
0.0.0.0/0 will allow any other host at the far end
to ping and/or telnet to the router.
xxx.xxx.xxx.xxx/32
IP Router - Release 1.8
7
Quick Start Guide
Internet Connection using PPP, NAT/PAT and Firewall Filters
Command
Description
add 1 "wan1" firewall 2 pass
inout nolog ping
192.168.21.14/32
Adds a Firewall rule to the WAN. Where
xxx.xxx.xxx.xxx is the host’s IP address at the far
end that will be able to ping or telnet to the router.
0.0.0.0/0 will allow any other host at the far end
to ping and/or telnet to the router.
xxx.xxx.xxx.xxx/32
add 1 "wan1" firewall 3 pass
inout nolog ping 0.0.0.0/0
0.0.0.0/0
Adds a Firewall rule to the WAN.
Adds a Firewall rule to the WAN.
Adds a Firewall rule to the WAN.
add 1 "wan1" firewall 4 pass
inout nolog tcp 1-65535 0.0.0.0/0
0.0.0.0/0
add 1 "wan1" firewall 5 pass
inout nolog udp 1-65535 0.0.0.0/0
0.0.0.0/0
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
reset 1
Reboot the router, to enable all configurations set
8
IP Router - Release 1.8
Quick Start Guide
Internet Connection using NAT and Static NAT Addresses
Internet Connection using NAT and
Static NAT Addresses
Router in Slot 1
ISP Router that provides the Internet connection. Router with NAT and Static NAT
addresses.
Command
Description
set clock1 a:1
set 1 default
disconnect a:1
Set primary master transmit clock source
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the from "LocalUnit" (default) to
"Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set ethernet ip address
192.168.21.15 255.255.255.0
Set the Ethernet IP address and Subnet Mask, for
the
set 1:1 ip address 192.168.21.14
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
set 1 "wan1" nat enable
Set the WAN interface named "wan1" enable
NAT mapping
set 1 "wan1" nat address
216.174.44.2 1
Set the WAN interface named "wan1" NAT
address
add 1 "wan1" static ip network
0.0.0.0 0.0.0.0 1
Adds a static IP network (route) to the WAN
interface
add 1 "wan1" static nat address
192.168.21.14 216.174.44.232
Add static NAT bi-directional mapping to wan1
IP Router - Release 1.8
9
Quick Start Guide
Internet Connection using NAT and Static NAT Addresses
Command
Description
add 1 "wan1" static nat address
192.168.21.15 216.174.44.233
Add static NAT bi-directional mapping to wan1
add 1 "wan1" static nat address
192.168.21.16 216.174.44.234
Add static NAT bi-directional mapping to wan1
Add static NAT bi-directional mapping to wan1
add 1 "wan1" static nat address
192.168.21.17 216.174.44.235
set 1:1:1 encapsulation fr
set 1 lmi annexd
Set the encapsulation on trunk 1 to Frame Relay
Disable LMI Annex D
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
set 1 "wan1" dlci 101
reset 1
Set the DLCI number
Reboot the router, to enable all configurations set
216.174.44.232 is the static NAT address assigned to the router.
216.174.44.233 is the static NAT address assigned to the controller.
216.174.44.234 is the static NAT address for a server*.
216.174.44.235 is the static NAT address for a host*.
*In the private network that can be reached from the outside world.
There can be up to 16 static NAT addresses, therefore the actual range can be
216.174.44.232 to 216.174.44.247. Only 4 were used in this example.
10
IP Router - Release 1.8
Quick Start Guide
Back-to-Back with PPP
Back-to-Back with PPP
The following configuration will set up two Adit 600 Routers back-to-back with PPP.
24 DS0s
wan1: PPP or Frame Relay
Static Routes
IP
Boulder Router in Slot 1
Command
Description
set 1 default
disconnect a:1
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 1.1.1.1
255.255.255.0
Set the Ethernet IP address, in the conventional IP
address format. (Router LAN)
set 1:1 phy auto
Set the Physical Specifications to auto-negotiate
add 1 "wan1" static ip network
2.2.2.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
reset 1
Reboot the router, to enable all configurations set
IP Router - Release 1.8
11
Quick Start Guide
Back-to-Back with PPP
Denver Router in Slot 1
Command
Description
set 1 default
disconnect a:1
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set primary master transmit clock source
set clock1 a:1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Denver"
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
Rename the from "LocalUnit" (default) to
"Denver" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 2.2.2.1
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
set 1:1 phy auto
Set the Physical Specifications to auto-negotiate
add 1 "wan1" static ip network
1.1.1.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
reset 1
Reboot the router, to enable all configurations set
12
IP Router - Release 1.8
Quick Start Guide
Back-to-Back with Multi-Link PPP
Back-to-Back with Multi-Link PPP
The following configuration will set up two Adit 600 Routers back-to-back with Multi-
Link PPP.
Boulder Router in Slot 1
Command
Description
set 1 default
disconnect a:1
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
connect a:2:all 1:1:2
rename 1 "LocalUnit" "Boulder"
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
rename 1 "LocalUnit" "Boulder"
set 1:1:1-2 multilink group 1
rename 1 "RemoteUnit" "wan1"
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 1.1.1.1
255.255.255.0
Set the Ethernet IP address, in the conventional IP
address format. (Router LAN)
add 1 "wan1" static ip network
2.2.2.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 1 "wan1" trunk multilink
group 1
Set the WAN interface named "wan1" to be
mapped to trunk multilink group 1
reset 1
Reboot the router, to enable all configurations set
IP Router - Release 1.8
13
Quick Start Guide
Back-to-Back with Multi-Link PPP
Denver Router in Slot 1
Command
Description
set 1 default
disconnect a:1
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set primary master transmit clock source
set clock1 a:1
set a:1:all type data
connect a:1:all 1:1:1
connect a:2:all 1:1:2
rename 1 "LocalUnit" "Denver"
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
Connect all of T1-1 to the Router that is in slot 1
Rename the Adit 600 from "LocalUnit" (default)
to "Denver" (LAN)
set 1:1:1-2 multilink group 1
rename 1 "RemoteUnit" "wan1"
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 2.2.2.1
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
add 1 "wan1" static ip network
1.1.1.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 1 "wan1" trunk multilink
group 1
Set the WAN interface named "wan1" to be
mapped to trunk multilink group 1
reset 1
Reboot the router, to enable all configurations set
14
IP Router - Release 1.8
Quick Start Guide
Back-to-Back with Frame Relay
Back-to-Back with Frame Relay
The following configuration will set up two Routers back-to-back with Frame Relay.
Denver
Boulder
1.1.1.1/24
1.1.1.1/24
24 DS0s
wan1: PPP or Frame Relay
Static Routes
IP
Boulder Router in Slot 1
Command
Description
set clock1 internal
set 1 default
Set primary master transmit clock source
Set Router to default settings
disconnect a:1
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 1
Disconnect all connections to the router in slot 1
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
set a:1:all type data
connect a:1:all 1:1:1
rename 1 "LocalUnit" "Boulder"
Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)
rename 1 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 1:1 ip address 1.1.1.1
255.255.255.0
Set the Ethernet IP address, in the conventional IP
address format. (Router LAN)
add 1 "wan1" static ip network
2.2.2.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 1:1:1 encapsulation fr
set 1 lmi disable
Set the encapsulation on trunk 1 to Frame Relay
Disable LMI (Local Management Interface)
set 1 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
set 1 "wan1" dlci 101
reset 1
Set the DLCI number
Reboot the router, to enable all configurations set
IP Router - Release 1.8
15
Quick Start Guide
Back-to-Back with Frame Relay
Denver Router in Slot 3
Command
Description
set 3 default
disconnect a:1
Set Router to default settings
Disconnect all connections to the T1 on the
Controller (slot a)
disconnect 3
Disconnect all connections to the router in slot 1
Set primary master transmit clock source
set clock1 a:1
set a:1:all type data
connect a:1:all 3:1:1
rename 3 "LocalUnit" "Denver"
Set the T1-1 of the Controller, Type to Data
Connect all of T1-1 to the Router that is in slot 1
Rename the from "LocalUnit" (default) to
"Denver" (LAN)
rename 3 "RemoteUnit" "wan1"
Rename WAN #1 from "RemoteUnit" (default) to
"wan1"
set 3:1 ip address 2.2.2.1
255.255.255.0
Set the ethernet IP address, in the conventional IP
address format. (Router LAN)
add 3 "wan1" static ip network
1.1.1.0 255.255.255.0 1
Adds a static IP network (route) to the WAN
interface
set 3:1:1 encapsulation fr
set 3 lmi disable
Set the encapsulation on trunk 1 to Frame Relay
Disable LMI (Local Management Interface)
set 3 "wan1" trunk 1
Set the WAN interface named "wan1" to be
mapped to trunk 1
set 3 "wan1" dlci 101
reset 3
Set the DLCI number
Reboot the router, to enable all configurations set
16
IP Router - Release 1.8
|