SABER (901)
CRUSADER (903)
SQUIRE (117)
USER MANUAL
Basic (Chess) Operation
MODE
1) Place the unit on a flat surface. Set up the chess pieces according to chess
rules (see the enclosed USCF Let’s Play Chess pamphlet), and press ON
and NEW GAME. The display should read PLAY. If not, see
Troubleshooting section.
2) Lightly press bottom edge of pawn on the FROM square E2; then press
again on the TO square E4.
3) Note the computer’s response in the display and move the computer’s
piece accordingly. (Example: Press bottom edge of pawn on the FROM
square E7 and then on the TO square E5, or as indicated.)
4) Continue to move by pressing the bottom edge of pieces on the FROM
and TO squares for white, and as indicated in the display for the
computer’s moves (black pieces).
Teach mode allows you to learn the rules of movement for each pieces
To enter teach mode, press NEW GAME and MODE
Then select one of the following modes:
1) Mode 1: King and pawns
Press Pawn symbol key
Press Knight symbol key
Press Bishop symbol key
Press Rook symbol key
Press Queen symbol key
2) Mode 2: Kings, Knights, and pawns
3) Mode 3: Kings, Bishops, and pawns
4) Mode 4: Kings, Rooks, and pawns
5) Mode 5: Kings, Queens, and pawns
This system allows you to learn the rules of movement for each peices.
Remove the unused pieces from the board. Make your first move. The
object, as in regular chess, is to checkmate the opposing king.
Key Functions
SET UP
NEW GAME
To change a piece’s color, remove it, add it, or move it to another square
1) Press SET UP and the display will show the position of the white king
1) Begins a new game.
2) Clears the computer’s memory.
(or press SET UP and Piece Symbol
for other pieces).
ON/CLEAR
2) Press the piece to change the piece to black.
3) Press the piece again to remove the piece.
4) Press any legal square to place the piece elsewhere on the board.
5) Repeat above steps 2 and 3 as desired.
1) Turns on the power.
2) Clears an incorrect FROM entry.
3) Exits from VERIFY mode
6) Press CLEAR to exit at anytime.
OFF/SAVE
Display Identifier:
Stops play. Press when it is your turn to move. The computer retains your
game in memory unless power is interrupted, or NEW GAME is pressed.
= white pieces
= black pieces
VERIFY
4
5
1) When it is your move, press VERIFY to check the position of the white
queen. Press VERIFY again to check the position of the black queen. To
exit press CLEAR.
2) Press VERIFY and the piece symbol to verify the position of the other
pieces on the board.
3) Press NEW GAME and MOVE to play black pieces from the bottom of
the board.
MULTI-MOVE
To exit press CLEAR.
1) To start with White on bottom, computer’s move - press MULTI-
MOVE, play your choice for white, then black. Then press MULTI-
MOVE and then MOVE, and computer will continue to play for white.
2) To monitor two humans playing, press MULTI-MOVE. A colon (:)
will appear in the display, and a beep will notify of any illegal moves.
3) To enter moves for both sides, press MULTI-MOVE. Press again to
resume normal play (human vs. computer)
LEVEL
The higher the time control (for the computer to think), the higher the
strength. Combined with the 5 training mode levels, there are a total of 433
level setting combinations. The default is set to level 6 (=6 seconds average
response time). Level 1=1 second; Level 72=124 Seconds; Level 73 =
infinite search
HINT
1) Press LEVEL to display the current level.
2) Press LEVEL again to increase the level by one.
3) Press the MODE key to increase the level by ten.
Press CLEAR to exit.
When it is your move, press HINT for move suggestions (not available on
some levels or during openings and certain positions). You may accept and
make the move, or press CLEAR to enter a different move.
Special Moves and Situations
On infinite level, the computer will search until it finds mate, until its
search memory is exhausted, or until the MOVE key is pressed. Use this
level for problem solving mode.
Castle
To enter the castling maneuver, move the King first (enter the moves by
pressing the squares). Then move the Rook. There is no need to press the
squares for the Rook. The computer automatically assumes you will move
its Rook during this procedure
TAKE BACK
1) Press TAKE BACK only when it is your turn to move.
2) Press the squares for the computer’s move in reverse order, as indicated
in the display.
Pawn Promotion
3) Press the squares for your move in reverse order, as indicated in the
display.
4) Replace all captured pieces.
The computer automatically promotes a pawn to a queen. If you choose
another piece, use the SETUP feature.
MOVE
En Passant
1) Press MOVE while waiting for the computer’s response to force the
computer’s next move.
2) Press MOVE when it is your turn to move to switch sides with the
computer. (The computer will move for you.)
When a pawn is captured En Passant, the captured pawn should simply be
removed from the board (there is no need to press the square). See USCF
rules for explaination.
6
7
Starting positions
Improper response
1) VERIFY function to determine if a mistake
was made in moving the pieces
2) check that the TO square is pressed for your
move
3) check that the move is legal (examples: you
can not move and remain in check; You may
not castle through check. Was En Passant
performed correctly, etc.)
1) To start with white on bottom, human’s move - press NEW GAME
2) To start with black on bottom, human’s move - press NEW GAME and
MOVE.
3) To start with White on bottom, computer’s move - press MULTI-
MOVE, play your choice for white, then black. Then press MULTI-
MOVE and then MOVE, and computer will continue to play for white.
Illegal Moves
If you make an illegal move, the beep tone will be lower and the display will
not register your move. To clear the display, press on the incorrect squares in
reverse order. Then perform a legal move. Or press clear and make a new
move.
Problem Solving
1) Clear the board by pressing NEW GAME, SET UP, and MODE.
2) Place pieces on the board by pressing Piece Symbol key and the square to
be occupied once for white, twice for black.
3) After setting up pieces, tell the computer whose move it is by pressing the
BLACK/WHITE key. The display will read SIDE. Press repeatedly until
the color indicator box of choice appears in the display.
4) Press ON/CLEAR
5) Press LEVEL. Set to level 73, the problem solving level.
6) Press ON/CLEAR.
Note: We recommend using the VERIFY function after setting up problem
solving, to check the position of all the pieces.
Troubleshooting
Remedy
Press ON/CLEAR
1) check if adapter/mains is plugged in; or if batteries are
installed correctly or are weak
Action/Display
Error message
No display
2) check if adapter/mains specifications match those on the
label under the base of the unit
3) put safety pin (or other sharp thin pen, etc.) into the
ACL (reset) hole under the unit
8
9
|