®
SoundWorks
i525
USER MANUAL
Additional Safety Advice
FCC STATEMENT FOR THE U. S. A. This equipment has
been tested and found to comply with the limits of part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by tuning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
1) Keep surrounding objects at least four inches away
from the apparatus for adequate ventilation.
2) Ventilation openings on the apparatus should not
be impeded by such items as newspaper, cloths,
curtains, and the like.
3) Do not place naked flame sources near the appara-
tus, such as lighted candles.
4) Dispose of the battery in accordance with local
safety regulations.
5) Do not operate the apparatus at a temperature less
than 36˚ F/ 2˚ C or greater than 100˚ F/38˚ C.
CAUTION
•
DO NOT REMOVE THE EXTERNAL ENCLOSURE PARTS
TO EXPOSE THE ELECTRONICS. NO USER SERVICE-
ABLE PARTS ARE INSIDE.
IF YOU ARE EXPERIENCING PROBLEMS WITH THIS
PRODUCT, CONTACT CREATIVE LABS NORTH
AMERICA OR CREATIVE LABS EUROPE FOR A SERV-
ICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT
HAS BEEN REPAIRED.
• Reorient or relocate the equipment and/or
the receiving antenna.
• Increase the separation between the equip-
ment and receiver.
• Connect the equipment to an AC outlet of a
different mains circuit from the mains circuit/
outlet providing power to the receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
•
For CANADA
AC POWER CORD CONNECTION
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
Pour le CANADA
CAUTION
Changes or modifications to this equipment not ex-
pressly approved by Creative Labs or Cambridge Sound-
Works for compliance will void the user’s warranty.
CORDE DE CONNEXION CA
ATTENTION:
POUR EVITER LES CHOCS ELECTRICQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSET JUSQU’AU
FOND.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
ꢁ
ꢂ
Table of Contents
Introduction and Contents .............................................................................6
Getting Started................................................................................................7-8
Display Brightness Control..............................................................................9
Radio Operation.........................................................................................10-11
iPod Operation................................................................................................. 12
X-Fi Processing ................................................................................................. 13
Quick Reference-Top panel.......................................................................... 14
Quick Reference-Remote Control.............................................................. 15
Quick Reference-Rear Connections.......................................................... 16
Convenience Features ................................................................................... 17
Wakeup Functions ....................................................................................18-21
Specification...................................................................................................... 22
Please Note: The contents of this document are subject to change without notice.
documentation.
ꢃ
INTRODUCTION
Additional Features
The people at Cambridge SoundWorks,
division of Creative Technologies, hope
you enjoy your new high-performance
SoundWorks i525. In addition to bringing
your iPod ’s music library to life, your new
music system has great FM stereo sound
and plays useful AM band stations. It stores
8 FM station presets along with 8 AM station
presets.
• A dimmer function allows you to choose one
of eight different brightness levels.
• The i525 has a built-in energy cell that
maintains the current time accurately without
AC power for up to ten minutes.
• A side jack allows easy connection of
headphones for private listening.
The SoundWorks i525 features the X-Fi suite
of audio enhancements, which improve
your audio enjoyment with a wide range of
program sources.
• A convenient MENU / SELECT button lets you
adjust Bass, Treble and Snooze time, as well as
other adjustable functions.
The large display and full-function remote
makes i525 operation easy from across the
room.
Contents
1) Sound Works i525
2) AC to DC Power Supply
3) Package of iPod dock inserts to fit a variety of
Apple iPod models.
4) Infrared Remote Control.
1
Not Pictured
SoundWorks i525 User Manual
AM Antenna
2
iPod
V O LU M E
ENTER
S E L E C T
S O U R C E
M E N U
S E E K
Examples only.
TUNE
Your parts may differ
in appearance.
S M A R T V O L S U R R O U N D C R Y S TA L I Z E R
1
2
6
3
7
4
PRESETS
5
8
3
M U T E
SLEEP
NAP
S N O O Z E
1
2
4
ꢄ
GETTING STARTED
A) Remove the SoundWorks i525 from its protective
polybag and place it in your preferred location.
A
B
B) On the rear panel, locate the FM wire antenna.
Remove the wire tie, then unroll and extend the
antenna.
EXTEND THE FM ANTENNA
C) Connect the Power Supply to a convenient AC
outlet. Then insert the Power Supply DC plug into
the DC POWER INPUT jack in the rear panel of the
i525.
C
CONNECT THE POWER SUPPLY
DC
POWER
INPUT
AUX
IN
AM
ANT
DC POWER INPUT jack
Connect the power
supply to this jack.
Input: 12V
1500 mA
ꢅ
GETTING STARTED (Continued)
Set the Current Time
D
TIME ADJUSTMENT
D) After connecting the i525 to power, it may show
“AM 12:00”. This indicates the current time needs to
be adjusted.
TUNE
PRESET
1-8
Press and hold MENU / SELECT on the top of the
i525 for 5 seconds. This will begin the “Time Set”
function. Release the button when “12”appears
with a blinking “:”.
MENU
SELECT
SLEEP
NAP
2
Use the WHEEL on the top panel to adjust the
current hour. Press MENU / SELECT, then use the
WHEEL again to adjust the current minutes setting.
Press MENU / SELECT, then use the WHEEL again
to adjust the day of the week, Press MENU / SELECT
to store the current time.
Note: The remote control can also adjust the
current time. Use the SELECT button on the
remote control, as you would the MENU / SELECT
button on the top panel. Use the VOLUME up and
VOLUME down buttons on the remote control, as
you would the WHEEL on the top panel.
iPod
V O LU M E
ENTER
M E N U
S E L E C T
S O U R
TUNE
Current Time Maintainence Feature
The i525 features a internal power cell that
maintains the clock’s accuracy during a short
interruption in AC power (up to ten minutes). This
device will never need replacement.
E
This device also lets you move the radio from one
site in a residence or office to another site without
losing the current time.
TUNE
Standby and On
SLEEP
NAP
E) Pushing the
button chooses Standby or On
operation.
M U T E
1
SLEEP
NAP
S N O O Z E
2
ꢆ
Brightness Function
TUNE
F) For quick and easy adjustment of the display
brightness, from Standby operation, repeatedly tap
the SNOOZE / MUTE button on the top panel. This
will cycle through the available brightness settings.
PRESET
1-8
SOURCE
MENU
SELECT
SLEEP
NAP
1
2
Once the desired brightness setting is displayed,
simply wait for the menu to timeout
(about 5 seconds) and the brightness setting is
stored.
SNOOZE / MUTE
ꢇ
RADIO OPERATION
Selecting the Radio Bands
A
RADIO BUTTON
iPod
V
O
L
U
E
M
E
A) Press SOURCE to select radio operation. The i525
returns to the last radio band and frequency used.
Pressing SOURCE during radio or AUX operation in
the following sequence--FM, AM, AUX, then back
to FM.
Note: AUX selection is omitted if there is no plug
connected to the AUX input jack on the back panel.
ENTER
S
E
L
C
T
M
S
E
E
N
U
PRESET
1-8
SOURCE
S
O
U
R
C
E
E
K
TUNE
S
M
A
R
T
1
5
E
1
2
O
Z
E
1
Tuning Stations
B) Auto Tune: Press the SEEK button on the remote
SEEK
B
or press and hold either TUNE [
and
]
TUNE
on the i525 top panel to automatically tune (seek)
to the next station.
iPod
V
O
L
U
E
M
E
ENTER
S
E
L
C
T
M
E
E
N
U
S
O
U
R
C
E
S
E
K
TUNE
S
M
A
R
T
V
O
L
S
U
R
R
O
U
N
D
C
R
Y
S
TA
3
7
L
I
Z
E
R
1
5
2
6
4
PRESETS
SLEEP
NAP
8
M
U
T
E
SLEEP
NAP
S
N
O
O
Z
E
1
Press and Hold
TUNE BUTTONS
C
C) Manual Tune: To find a specific frequency, tap
a TUNE button [
and
] to advance one
TUNE
iPod
V
O
L
U
M
E
frequency increment at a time.
ENTER
S
E
L
E
C
T
M
S
E
E
N
U
S
O
U
R
C
E
E
K
TUNE
S
M
A
R
T
V
O
L
S
U
R
R
O
U
N
D
C
R
Y
S
TA
3
7
L
I
Z
E
R
1
5
2
6
4
8
PRESETS
SLEEP
NAP
M
U
T
E
SLE
S
N
O
O
Z
E
1
2
10
RADIO OPERATION (continued)
Storing Stations in the PRESET Bank
You can store eight FM stations in the i525’s PRESET
bank while FM is selected and eight AM stations
while AM is selected.
PRESET BANK ON THE REMOTE CONTROL
A
A) Storing a radio frequency as a PRESET using the
remote control:
Press SOURCE to choose the desired radio band
iPod
V O LU M E
ENTER
(AM or FM).
Tune to the desired station.
S E L E C
T
M E N U
S E E K
S O U R C E
TUNE
Press and hold the target PRESET button on the
remote until the preset number is solid on the
display.
S M A R T V O L S U R R O U N D C R Y S TA L I Z E R
1
2
6
3
7
4
PRESETS
The station frequency is stored as a Preset.
5
8
M U T E
SLEEP
NAP
S
N
O
O
Z
E
1
2
PRESET SELECTION FROM THE TOP PANEL
B
B) Storing a radio frequency as a PRESET using the
top panel controls:
Press SOURCE to choose the desired radio band
(AM or FM).
Tune to the desired station.
Press and hold PRESET 1-ꢆ on the top panel until
the display changes to show Preset numeral 1.
Within five seconds, repeatedly press PRESET 1-ꢆ
until the target PRESET number is shown.
Tap the MENU SELECT button.
PRESET
SOURCE
1-8
MENU
SELECT
The station frequency is stored as a Preset.
2
SNOOZE / MUTE
11
iPod Operation
1) Install the dock insert that fits your iPod.
Using the iPod dock feature of the i525
1) There is a selection of inserts included with
the i525. These inserts fit various iPod models.
Install the insert that best fits your iPod, or use
the insert included with your Apple iPod.
Make sure the insert snaps into the recess. The
top of the insert should be flush with the top of
the i525.
2) Attach your iPod to the dock connector.
3) Select the iPod as a music source by pressing
PLAY / PAUSE (remote or top panel).
4) Use the iPod navigation buttons on the remote
control to operate your iPod while it is docked
in the i525.
2) Connect your iPod.
U N
E
M
i525 Top Panel
3) Select Play / Pause
i525 Remote Control
Notes:
To wake a hibernating iPod, push PLAY / PAUSE on
the i525 remote control or top panel.
iPod
V O LU M E
ENTER
The i525 will not control a connected iPod while
the i525 is in STANDBY.
M E N U
S E L E C T
S O U R C E
The i525 controls iPod functions of a docked
iPhone or iPod touch. After docking one these
models, it may be necessary to manually“unlock”
and select the iPod function before the i525 remote
control can be used.
TUNE
S E E K
4) Use these iPod buttons to
operate your iPod.
1ꢀ
Creative’s X-Fi audio processing technology
Using the X-Fi features of the i525
Creative Multi-Speaker Surround Virtual-
Heaphones improves your headphone experience.
Use it whenever the i525 is available and you would
normally listen to you iPod on headphones.
Select X-Fi SURROUND while headphones are
connected to the i525 to employ this powerful
digital algorithm designed specifically for
headphones. With Creative Multi-Speaker Surround
Virtual-Heaphones, music seems to float in front of
you, instead of being trapped “between”your ears.
This effect greatly enhances any audio program on
headphones.
X-Fi technology on the i525 allows you to combine
four different audio enhancements, creating better
sound than possible “linear”audio circuitry. The
four different X-Fi enhancement choices are:
Crystalizer
Creative Multi-Speaker Surround Virtual -
Speakers (SURROUND on remote control)
Creative Multi-Speaker Surround Virtual -
Headphones (SURROUND on remote control,
when heaphones are connected)
Smart Volume Management (SMART VOL on the
remote control)
Smart Volume Management is a sophisticated
audio engine that eliminates disruptive changes in
output from any audio program. It is useful anytime
that large volume changes are unwelcome.
a) Use it at night at a low volume when you
want to hear all the music but don’t want it
to get too loud.
iꢃꢀꢃ Remote Control
Combined
X-Fi processing On/Off
Creative Multi-Speaker
Surround-Virtual On/Off
b) Use it on radio to “harmonize”the output
of different stations, which otherwise may
have different overall sound levels.
S M A R T V O L S U R R O U N D C R Y S TA L I Z E R
c) Smart Volume Management is also
useful if you want to hear music in a noisy
environment. With SVM, you can set the
radio to a level loud enough to overcome the
background noise, secure in the knowledge
that your music will maintain this consistent
output level.
Creative Smart Volume
Management On/Off
Creative Crystalizer
On/Off
Crystalizer restores the crisp treble and bass punch
erased by audio compressor processing employed
to create MP3, AAC, and other similar files from the
original, higher quality audio file. FM radio and any
compressed audio files sound more life-like when
Crystalizer is used.
The CRYSTALIZER, SURROUND and SMART VOL audio
functions on the remote control can also be
combined. For instance, you can combine
Crystalizer and Smart Volume Management,
Surround with Smart Volume Management, or
combine all three. Select which processes you
want. Once you have made your choice, you can
use the X-Fi button on the remote control to
compare enhanced (combined X-Fi processing)
with the non-enhanced audio.
Creative Multi-Speaker Surround Virtual analyzes
the audio signal and restores the sonic cues
inherent in the original material’s wide soundstage.
When X-Fi SURROUND is chosen on the i525,
music seems to fill the width of the room. The i525
disappears as the source of the sound.
1ꢁ
QUICK REFERENCE GUIDE - SOUNDWORKS i525 TOP PANEL CONTROLS
Select iPod mode if an
iPod is docked.
Select iPod Play/Pause.
Snooze adjustments.
Press and hold for current time/
day adjustment.
Radio: manual tune.
iPod: next/previous
track.
Adjust playback volume
and settings
sequence.
Press and hold to select preset
and store current station.
TUNE
PRESET
1-8
SOURCE
MENU
SELECT
SLEEP
NAP
1
2
“Standby”and “On”operation.
When in “Standby”, Press to
trigger delayed On (Nap).
(15m, 30m, 45m, 60m, 90m,
120m, 180m, 240m).
When in “On”operation, Press
to trigger delayed Standby
(Sleep).
SNOOZE / MUTE
Press and hold to adjust alarm.
Normal operation: Mute/Unmute.
During alarm operation: Activate snooze.
(15m, 30m, 45m, 60m, 90m,
120m).
Radio and band selection.
Selects between radio bands and Aux only if a
source is plugged into the Aux input.
1ꢂ
QUICK REFERENCE GUIDE - SOUNDWORKS i525 REMOTE CONTROL
Move up and down within an iPod menu.
THESE BUTTONS SUBSTITUTE FOR THE CLICK WHEEL ON AN iPod.
Select iPod player, if docked.
Toggle between iPod Play/Pause.
iPod
Press to move back and forth within the
current playlist.
Press and hold to forward scan or reverse
scan the current program.
ENTER
PRESS MENU TO SHOW THE
iPod’s MENU FUNCTION
Choose menu items or start program play.
MENU
iPod
VOLUME
Same as top panel.
ENTER
MENU
SELECT
SOURCE
Activate/cancel
TUNE
SEEK
CREATIVE MULTI-SPEAKER SURROUND
VIRTUAL
Activate/cancel
combined X-Fi audio
or CREATIVE MULTI-SPEAKER SURROUND
VIRTUAL-HEADPHONES audio processing.
Activate/cancel
CREATIVE SMART
VOLUME MANAGEMENT
audio processing.
Activate/cancel CREATIVE CRYSTALIZER
audio processing.
SMART VOL SURROUND CRYSTALIZER
1
2
6
3
7
4
Press and hold any preset to store the
current station.
PRESETS
5
8
Same as top panel.
MUTE
SLEEP
NAP
SNOOZE
1
2
1ꢃ
QUICK REFERENCE GUIDE - SOUNDWORKS i525 REAR CONNECTIONS
DC
POWER
INPUT
AUX
IN
AM
ANT
Input: 12V
1500 mA
DC Input jack
Connect the power
supply to this jack.
Connect any audio signal source with
a 3.5 mm stereo miniplug to this jack.
Listening to An External Sound Source
A) If you have an external audio program source (a
portable MP3 player, for example), connect it to the
AUX IN jack on the rear panel.
B) Press the SOURCE button on the front panel or
remote control until the AUX icon appears on the
display screen. NOTE: AUX can not be selected if
there is no miniplug connected to the AUX IN jack
on the rear panel.
1ꢄ
CONVENIENCE FEATURES
Mute
A) Press the SNOOZE/MUTE bar (top panel) or the
SNOOZE/MUTE button on the remote control.
Mute is cancelled if the POWER button is pressed
or the volume is adjusted.
Sleep Delay
B) SLEEP DELAY ADJUSTMENT
B) Delayed Turn Off function: While the i525 is “On”,
press the SLEEP button on the remote control or
the SLEEP / NAP button on the top panel until the
desired sleep delay interval is reached.
ADJUST
SLEEP
Sleep delay intervals are 15, 20, 30, 45, 60, 90 and
120 minutes. Sleep delay is cancelled if the POWER
button is pressed.
C) NAP ADJUSTMENT
Nap Feature
ADJUST
C) Use NAP for an automatic turn on after a specific
period of time. Set the radio or iPod to your desired
playback volume. Press the POWER button to enter
Standby operation. Press the NAP button on the
remote control or the SLEEP / NAP button on the
top panel using repeat presses until the desired
nap interval is reached.
NAP
Nap intervals are 15, 20, 30, 45, 60, 90, 120,180, and
240 minutes. Nap is cancelled if the POWER button
is pressed.
SELECT BUTTON ADJUSTMENT
D) BASS ADJUSTMENT
MENU / SELECT button operation:
D) Press the MENU / SELECT button on the top
panel or SELECT remote control to select the BASS,
TREBLE, SNOOZE, X-Fi, and Alarm Day adjustments.
ADJUST
BASS
Use the WHEEL on the top panel of the i525 or
use the Volume buttons [
and
] on the
5 6
remote control to adjust settings of BASS, TREBLE,
SNOOZE, X-Fi, Alarm Days, and Brightness. Any
SELECT button function stores its current setting
and returns the i525 to normal operation after five
seconds of inactivity. Pressing other i525 buttons
during a SELECT button function may cancel
SELECT button adjustment.
E) TREBLE ADJUSTMENT
ADJUST
TREBLE
F) SNOOZE ADJUSTMENT
•
•
•
Bass: Adjustment range is -8 to +8.
Treble: Adjustment range is -8 to +8.
Snooze Interval Adjustment is 5 minutes to 30
minutes.
ADJUST
•
•
•
X-Fi Adjustments are All Off, Crystalizer On,
CMSS On, SVM On, and combinations.
Wakeup day pattern Adjustments are 7 Day, 5
Day, or 2 Day (see next page).
Brightness Adjustment range is 1 to 8.
1ꢅ
WAKEUP FUNCTIONS
Music Wakeup Features
After a Music Wakeup event occurs, the Music
alarm will continue for one (1) hour. After one hour,
the alarm will reset itself and the i525 will enter
Standby.
Each of the two Wakeup Alarms on the i525 will
store the following settings:
Wakeup time
Wakeup source (radio frequency, iPod)
Wakeup Volume (for radio or iPod)
X-Fi setting
If a second alarm is set to occur during the
activation time of the first alarm, the second alarm
will override the first alarm. This allows a user to
set the Music wakeup for 30 minutes earlier than a
Tone wakeup.
The Alarm Settings on the i525 are maintained
even if the i525 is unplugged.
Tone Wakeup or Music Wakeup
When activating either alarm, the user chooses
between Tone wakeup and Music wakeup. Tone
wakeup uses an electronic tone to wakeup the
user at the stored wakeup time. Music wakeup uses
the stored settings for source, volume and X-Fi
processing.
Please note: Once the Wakeup settings have been
stored, use the i525 any way you wish, with any
source. The i525 will wakeup according to the
stored wakeup settings.
Storing The Wakeup Settings--Overview
Storing your desired wakeup settings for either
Alarm 1 or Alarm 2 involves two steps.
Wakeup day pattern--7 days a week, 5
days a week (Monday to Friday) and 2
days a week (Saturday and Sunday).
This setting is adjustable in the MENU
SELECT button operation discussed on
page 17.
First, set the i525 to your desired source, volume
and X-Fi setting.
Second, press and hold an Alarm button until you
see the display change. Now you can adjust the
wakeup hour, the wakeup minutes and the daily
wakeup pattern.
DAYS OF WEEK ADJUSTMENT DISPLAY
ADJUST
5
MON TUE WED
THU FRI
DAY
At the end of this simple adjustment session, the
i525 reminds you of the stored wakeup settings on
its display.
After a Tone Wakeup event occurs, the Tone alarm
will continue for ten minutes. After ten minutes,
the alarm will reset itself and the i525 will enter
Standby.
1ꢆ
WAKEUP FUNCTIONS (Continued)
Preparing either Alarm 1 or Alarm 2:
PART ONE: PRESELECT THE SOURCE AND VOLUME
A) Turn the i525 on.
B) Select a radio station or iPod playback.
C) Set the Volume.
D) Adust X-Fi settings, if desired.
(Smart Volume Management is a great choice
for Music Wakeup, as it keeps the volume
consistent.)
PART TWO: ADJUST THE HOURS AND MINUTES
A) Press and hold either ALARM 1 or ALARM 2.
The display changes to Hour adjustment.
ALARM ADJUSTMENT DISPLAYS
A) HOUR ADJUSTMENT DISPLAY
ADJUST
Use the TUNE/ADJUST buttons [
and
] to
] to
adjust the correct wakeup hour.
B) Press the same Alarm button or SELECT.
The display changes to Minutes adjustment.
Use the TUNE/ADJUST buttons [
and
B) MINUTES ADJUSTMENT DISPLAY
adjust the correct wakeup minute.
ADJUST
C) Press the same Alarm button or SELECT to store
your alarm preferences.
The display will show, in sequence:
Stored Wakeup Time and Daily Pattern
Stored Wakeup Source (radio frequency or iPod)
Stored Wakeup Volume and Wakeup X-Fi setting.
1ꢇ
WAKEUP FUNCTIONS (Continued)
Activating/Deactivating Alarms
Activating/Deactivating Alarms
i525 Top Panel
i525 Remote Control
Press either alarm button to activate or deactivate
that alarm. Both alarm buttons follow this sequence:
1
2
6
3
7
4
PRESETS
5
8
PRESET
1-8
SOURCE
Start: ............................................... Alarm inactive
First alarm button press:................ Tone Alarm
Second alarm button press: ....... Music Alarm
Third alarm button press: ........ Alarm inactive
M U T E
SLEEP
NAP
S
N
O
O
Z
E
1
2
2
Music Alarm occurs only if the i525 is in Standby.
Tone Alarm occurs if the i525 is in Standby or On.
Use Tone Wakeup as a reminder function during the
day while using the i525 normally.
No activated alarms
FRI
PRESET
CRYSTALIZER
SURROUND
Alarm 1 set for Tone Wakeup, 7 days a week
7 DAY
FRI
PRESET
CRYSTALIZER
SURROUND
Both alarms set for Music Wakeup. Alarm 1 set for
5 days a week, Alarm 2 set for 7 days a week.
5
DAY
FRI
7 DAY
PRESET
CRYSTALIZER
SURROUND
Alarm 2 set for Tone Wakeup, 2 days a week
2
FRI
DAY
PRESET
CRYSTALIZER
SURROUND
ꢀ0
Cancelling An Alarm for the Day
iPod
To cancel an alarm for the day and reset it for
operation the next day, press either Alarm button
or the power button. The i525 will enter Standby.
The alarm will remain activated and occur on the
next day in the designated pattern.
V O LU M E
Snooze / Mute Button
ENTER
M E N U
S E L E C T
S O U R C E
TUNE
S E E K
Snooze Function
Tapping the SNOOZE/MUTE bar on the i525 or the
SNOOZE/MUTE button on the remote will silence a
Wakeup alarm for nine minutes (default). To change
the SNOOZE duration, use the SELECT and TUNE/
S M A R T V O L S U R R O U N D C R Y S TA L I Z E R
1
2
6
3
7
4
ADJUST buttons [
and
] to change the
PRESETS
settings (5 minutes to 30 minutes).
5
8
M U T E
SLEEP
NAP
S N O O Z E
1
2
To silence and reset any active alarm,
press either alarm button or the power
button, on the top panel or the remote.
TUNE
PRESET
1-8
SOURCE
MENU
SELECT
SLEEP
NAP
1
2
SNOOZE / MUTE
Snooze / Mute Bar
ꢀ1
SPECIFICATIONS
Internal audio source
FM stereo/AM tuner (all digital processing of analog RF signals)
Inputs:
Apple iPod Dock on the top panel
Rear panel Aux input (3.5 mm stereo minijack)
Outputs:
One front panel headphone output (3.5 mm stereo minijack)
Dimensions:
Height:
Width:
Depth:
Weight:
3 3/8 in
10 in
6 in
86 mm
255 mm
153 mm
1.4 kg
3 lbs
Power Consumption, maximum:
20 watts
Input voltage:
DC 12V
ꢀꢀ
ꢀꢁ
Cambridge SoundWorks
120 Water Street
North Andover, MA USA 01845
R1, 22 March 2010
P81-2440
ꢀꢂ
|