1 Removing or re-fitting your seat unit
(the seat cover must be removed before fitting the infant carrier)
1a
1b
1c
1d
1e
B
A
HANDY HINT -
HANDY HINT -
Unfasten the hook and
loop fastenings and
press studs shown by
the red circles
Unclip the hooks on
Remove the seat unit
both sides of the buggy from the chassis by
You may find it easier
to apply the brake
before removing or
re-fitting the seat unit.
Please refer to the user
guide for your buggy for
operation of the brake.
You may find it easier
to stand behind or to
the side of the buggy.
Remove the hood
and bumper bar
by simultaneously
pressing the buttons on
the mouldings on both
(dia 1d).
sliding the base tabs
upwards and out of the
grooves.
Then slide the top tabs
upwards and out of the
grooves until the seat
unit is disengaged
(dia 1e).
(dia 1c).
UK
User Guide
Unfasten the press
A
studs on the backrest sides of the buggy and
and unfasten the hook
and loop fastenings on
both sides of the seat
unit where it overlaps
slide them upwards
until they disengage
(dia 1b).
To re-fit the seat
unit reverse these
instructions.
B
the hood (dia 1a).
2 Attaching your child seat for use as a travel system
(this vehicle is intended for children from birth and up to 13kgs)
2d
2e
2a
2b
2c
HANDY HINT -
To fit the adaptor to the Lower the child seat
To remove the child
seat move the handle
to the carrying position.
Lift the lever on the
IMPORTANT -
child seat squeeze the
lever and insert into
the space below the
handle (dia 2b). Make
sure it is fully fitted and
release the lever to
lock into place. Repeat
this process for both
adaptors.
onto the buggy making
sure that the adaptor
on either side drops
You may find it easier
to apply the brake
when fitting the child
seat. Please refer to
the user guide for your
buggy.
Clip the socket onto
the chassis from the
inside. Align the bottom
edge of the socket with
the edge shown on
It may be necessary to
remove the adaptors
from the child seat
when installing it in
your vehicle.
If the adaptors are in
contact with the vehicle
seat cushion, remove
them.
into both the sockets on adaptors and lift the
each side of the buggy
(dia 2c). Push down
firmly. Once the seat is
engaged you will hear
a click.
child seat out of the
sockets (dia 2d).
Verve P-Type
adaptor
Ensure that the left
hand and right hand
adaptors are used on
the correct side of the
child seat.
Move the handle to
To remove the
the rocking position.
Please refer to the user
guide for the child seat.
adaptors from the child
seat, pull the lever on
the adaptors away from
the child seat while
pulling down (dia 2e).
Repeat the process for
both adaptors.
the chassis (dia 2a).
Rotate the fixing arm.
Squeeze the housing
WARNING -
and fixing arm together IMPORTANT -
Check that the child
seat attachment
devices are correctly
engaged before use.
with one hand and
snap over the hook
with the other hand.
Repeat this process for
both sockets.
Ensure that the left
hand and right hand
sockets are used on
the correct side of the
buggy.
The buggy seat unit
must be removed
before attaching your
car seat.
The child seat is
Verve P-Type
socket
IMPORTANT -
compatible with
the ISOFIX base
Ensure your child is
harnessed at all times.
(purchased separately).
further information.
Only use a P-Type child seat on this buggy when fitted with a Verve P-Type socket
BBO-662-00
1282.000 - Verve Adaptors & Sock1
1
10/1/07 09:15:40
|