INSTRUCTION MANUAL
LEG PRESS OPTION FOR STRATA STRENGTH
TRAINING SYSTEM
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions,
or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized
dealer service centers or our home office customer service department. Please call your local dealer
for assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide
immediate assistance to you, free of charge.
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system
is guaranteed for as long as you own it. We will repair or replace anything that goes wrong.
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
PARTS LIST
NO.
DESCRIPTION
QTY.
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
84A
BASE CONNECTION
FRONT BASE
1
1
1
1
2
1
1
1
1
1
1
4
15
2
1
8
1
4
8
2
2
2
4
2
3
2
2
4
12
2
18
6
9
1
1
3
1
1
2
1
1
LEG PRESS SUPPORT
REAR TUBE
SLIDING SEAT SUPPORT FRAME
SEAT SUPPORT
SLIDING TUBE
FOOT REST
STEEL ROLLER
HANDLE BAR
SINGLE PULLEY BRACKET
50 ID. SQUA. END CAP
50 SQUA. END CAP
RUBBER STOP
RUBBER BUMPER
NON-SKID PAD
SPRING PIN
3/4" STEEL BUSHING
1/2" STEEL BUSHING
1/2" X 7" HEX HEAD BOLT
1/2" X 3-1/2" HEX HEAD BOLT
1/2" X 3-1/8" HEX HEAD BOLT
3/8" X 3" HEX HEAD BOLT
3/8" X 2-1/2" HEX HEAD BOLT
3/8" X 2" HEX HEAD BOLT
3/8" X 1" HEX HEAD BOLT
3/8" X 3/4" HEX HEAD BOLT
5/16" X 1/2" SETSCREW
1/2" WASHER
3/8" WASHER(LARGE)
3/8" WASHER(SMALL)
1/2" NYLON NUT
3/8" NYLON NUT
LEG PRESS CABLE
HOOK
PULLEY
SEAT
BACK PAD
1" X 130 HAND GRIP
OWNER'S MANUAL
TOP CABLE (2890 mm)
1
PARTS CHART
REAR TUBE(204)
BASE
CONNECTION(201)
FRONT
BASE(202)
SEAT SUPPORT(206)
SLIDING TUBE(207)
SLIDING SEAT
SUPPORT FRAME(205)
STEEL
ROLLER(209)
SINGLE PULLEY
BRACKET(211)
LEG PRESS SUPPORT(203)
HANDLE BAR(210)
FOOT REST(208)
3/4" STEEL
RUBBER
STOP(214)
1/2" STEEL
BUSHING(219)
HOOK(235)
BUSHING(218)
1" x 130
HAND GRIP(239)
SEAT(237)
BACK PAD(238)
SPRING PIN(217) PULLEY(236)
LEG-PRESS CABLE (234) (2030 mm)
TOP CABLE(84A) (2890 mm)
FASTENER
5/16" X 1/2"
SETSCREW(228)
1/2" NYLON NUT(233)
3/8" NYLON NUT(234)
1/2" WASHER(229)
3/8" X 2-1/2" HEX HEAD BOLT(224)
1/2" X 3-1/2" HEX HEAD BOLT(221)
3/8" WASHER(LARGE)(230) 3/8" WASHER(SMALL)(231)
0"
1/2"
1"
1-1/2"
2"
2-1/2"
3"
3-1/2"
4"
4-1/2"
5"
5-1/2"
6"
6-1/2"
7"
2
STEP1
1.Attach BASE CONNECTION(201) and FRONT BASE(202) to the holes in the
LEFT WEIGHT BASE of Bodycraft Strata home gym using two 1/2" x 3-1/8" HEX
HEAD BOLT(222), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232).
2.Attach LEG PRESS SUPPORT(203) to FRONT BASE(202) using two 3/8" x 3"
HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON
NUT(232).
Attach REAR TUBE(204) to LEG PRESS SUPPORT(203) as shown using two
3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8"
NYLON NUT(232).
213
201
LEFT WEIGHT BASE
232
229
201
232
213
203
212
213
233
229
222
LEFT WEIGHT BASE
233
231
231
202
223
231
223
212
233
212
231
231
204
223
212
3
STEP2
To ensure best performance, lubricate all pivot points during assembly.
Insert two 3/4" STEEL BUSHING(218) and four 1/2" STEEL BUSHING(219)
to SLIDING SEAT SUPPORT FRAME(205).
Attach SLIDING SEAT SUPPORT FRAME(205) to LEG PRESS SUPPORT(203)
as shown using two STEEL ROLLER(209) as shown.
Tighten 5/16" X 1/2" SETSCREWS(228) with Hex Wrench to bolt STEEL ROLLERS
(209) in place.(See FIG B)
Attach eight NON-SKID PAD(216) to FOOT REST(208).
Attach SEAT SUPPORT(206) to SLIDING SEAT SUPPORT FRAME(205) as
shown using two 1/2" x 3-1/2" HEX HEAD BOLT(221), four 1/2" WASHER(229)
and two 1/2" NYLON NUT(232)
Attach FOOT REST(208) to SLIDING SEAT SUPPORT FRAME(205) as shown
using two 1/2" x 7" HEX HEAD BOLT(220), four 1/2" WASHER(229) and two
1/2" NYLON NUT(232).
213
213
218
218
219
216
205
219
208
218
218
220
213
229
229
232
229
232
229
FIG B
228
208
228
203
209
205
209
205
FIG A
213
203
227
214
229
230
230
214
221
229
206
213
227
229
232
207
217
206
4
STEP3
Attach HANDLE BAR(210) and SEAT(237) to SEAT SUPPORT(206) as shown
using two 3/8" X 1" HEX HEAD BOLT(226) and two 3/8" WASHER(231).
Attach BACK PAD(238) on SEAT SUPPORT(206) as shown using two 3/8" x 2-1/2"
HEX HEAD BOLT(224) and two WASHER(SMALL)(231).
CHECK that all the parts are in assembled correctly as drawing then
tighten all bolts. Attach all plastic ends caps and grips to appropriate
places.
239
210
239
238
237
231
224
206
210
226
226 231
5
LEG PRESS CABLE
LEG PRESS CABLE(234)
If previously installed, completely remove TOP CABLE(84), along with pulleys T1, T2,
T3, T4 and T5. Remove the two bolts and attach the TOP BEAM into the FRONT
UPRIGHT. Assemble TOP CABLE(84A) (from leg press box) and pulleys simultaneously.
Insert threaded end of TOP CABLE(84A) into slot in front of TOP BEAM, over pulleys
T1, T2, around pulley T3, and over T4. Run threaded end of TOP CABLE(84A) through
SINGLE PULLEY BRACKET(211) and attach pulley G1 as shown. Finish by routing TOP
CABLE(84A) over pulley T5 and attach threaded end of TOP CABLE(84A) into SELECTOR
ROD. For safety reasons, the threaded end should be screwed in using at least half of
the available screw length. The jam nut should be tightened to SELECTOR ROD to
prevent loosening. Replace the two bolts that attach the TOP BEAM to the FRONT
UPRIGHT and tighten. Make certain the TOP CABLE(84A) runs above these bolts.
Attach RUBBER BUMPER(215) to top of SINGLE PULLEY BRACKET(21).
TOP CABLE(84A)
T2
T1
T4
T5
84A
T5
75
51
80
9
84A
77
90
51
65
T3
L5
75
FLOATING PULLEY BLOCK(32)
TOP
CABLE(84A)
T2
T1
T4
P2
T5
AB
T3
L5
CABLE(86)
A2
T3
L5
L7
LOWER
CABLE(87)
G1
LOWER
CABLE(87)
84A
211
A2
L7
T3
234
L5
6
Screw thread end of LEG PRESS CABLE(234) into SINGLE PULLEY BRACKET(211).
Attach pulleys G2 and G3, making certain LEG PRESS CABLE(234) runs beneath
pulleys and is scated in pulley grooves. Attach the eyelet cable end to
ADJUSTMENT TUBE(207) as shown.
G1
234
G1
211
201
231
G2
225
231
G3
202
233
207
236
234
G2,G3
236
231
225
233
234
201,202
235
207
225
206
7
Assembly is complete! Please take the following steps before using the gym:
1. Make certain all bolts are tightened securely.
2. Make certain all cables are seated into all pulley grooves. A cable rubbing against
steel will peel the nylon coating, voiding warranty and resulting in a need for
replacement.
3. Pre-stretch the cables. Put the Weight Selector Pin (37) in the bottom hole on the
weight stack. Pull on the cables with great force, helping remove any kinks and
providing any initial cable stretch.
4. Be aware the cables can loosen and slightly stretch upon initial use.
5. The cables should be adjusted as tight as possible, but no so tight as to lift the Top
Plate (82) above the weight stack. Be certain to secure the jam nuts after
adjustments are made.
6. For better performance, apply a household lubricant (such as silicone) to any
adjustable areas and to the Guide Rods (8 ).
7. Enjoy many years of a Fit Lifestyle!
Thank you for purchasing the Bodycraft Strata Home Gym. If you have any
questions, please call your local Bodycraft dealer or call our customer service
department at 800-990-5556.
|