Radio / Cassette / Changer
Orlando DJ
A
Operating instructions
Contents
Quick reference ............................ 30 Storing stations ..................................... 40 Tape operation ............................. 46
Automatically storing the strongest sta-
tions with Travelstore............................ 41
Recalling stored stations ...................... 41
Scanning stored stations with
Preset Scan .......................................... 41
Scanning stations with Radio-Scan...... 41
Changing the scan time........................ 41
Selecting the seek tuning sensitivity .... 41
Switching from stereo to mono (FM) .... 42
PTY – Programme Type ....................... 42
Switching PTY on/off ......................... 42
Programme type ................................... 42
Checking the programme type of
Inserting a tape ..................................... 46
Removing a tape................................... 46
Fast Forward/Rewind ........................... 46
Selecting titles with S-CPS ................... 46
Switching the tape side ........................ 46
Tape equalisation ................................. 46
Scanning cassette titles with SCAN ..... 47
Dolby B NR*.......................................... 47
Skipping unrecorded tape portions
with Blank Skip ..................................... 47
Listening to the radio during fast tape
winding with RM.................................... 47
Care notes ............................................ 47
Important notes ............................ 36
Precautions ........................................... 36
Traffic safety ......................................... 36
Installation............................................. 36
Telephone mute.................................... 36
Accessories .......................................... 36
KeyCard theft protection
system........................................... 37
Putting the unit into operation .............. 37
Removing the KeyCard ........................ 37
“Training” a second KeyCard/
Replacing a KeyCard............................ 37
Displaying the radio pass data ............. 37
Short Additional Memory (S.A.M.)........ 38
Turn On Message (T.O.M.) .................. 38
Optical indication for extra security ...... 38
Care of your KeyCard ........................... 38
the station .......................................... 42
Displaying the selected programme
CD changer control A05.............. 48
Switching to CDC operation ................. 48
Selecting CDs and titles ....................... 48
MIX playback ........................................ 48
Selecting the display mode .................. 48
Storing the display mode ...................... 49
SCAN operation .................................... 49
Entering CD names .............................. 49
Deleting CD names with
type .................................................... 42
Selecting a programme type ............. 42
Storing programme types.................. 43
Scanning stations with PTY-SCAN ... 43
PTY priority........................................ 43
Switching the audio source ........ 38
Radio operation with RDS ........... 39
Receiving traffic programme
stations with RDS-EON................ 44
AF - Alternative frequency .................... 39
REG - regional programme .................. 39
Selecting a waveband .......................... 39
Station tuning ........................................ 39
Traffic announcement priority on/off .... 44
Warning beep ....................................... 44
Switching the warning beep off ......... 45
Automatic seek tuning start .................. 45
Adjusting the volume for traffic announce-
ments and the warning beep ................ 45
Adjusting GEO for traffic messages
DSC-UPDATE ...................................... 49
DSC programming ....................... 50
Overview of the DSC factory settings .. 52
Automatic tuning
/
....................... 39
Manual tuning with << >>.................. 40
Scrolling through the broadcasting
networks (only FM) ............................... 40
Changing the memory bank (FM)......... 40
Appendix ....................................... 53
Specifications........................................ 53
and the warning beep ........................... 45
29
Quick reference
Switching on with the ignition being
switched off:
To programme the mute volume level,
proceed as follows:
1 Switching on/off with the ON button:
Press ON.
To keep on operating the set when the
ignition is switched off (KeyCard is in-
serted), proceed as follows:
Press ON after the double beep tone.
The unit will be turned on.
•
•
Adjust the desired volume.
When switching the set on with the ON
button, the KeyCard has to be insert-
ed. The unit will play with the pre-
adjusted volume.
Press
for two seconds until you
hear a beep.
Now this volume level is stored as your
mute volume.
To avoid that the battery goes flat, the
system will be turned off automatically
after a playback time of one hour.
Extra function
Memory button in the DSC menu.
2 VOL+ / VOL-
4 FMT
To alter the volume.
Press repeatedly to switch between
the FM memory banks I, II and T
(Travelstore).
When pressing this button, the system
will automatically switch to FM.
Switching on/off with the KeyCard:
The set has to be turned on via the ON
button.
Each time the set is switched on, it will
play with the pre-adjusted volume
(VOL FIX).
You may also change the VOL FIX set-
ting (see chapter “DSC programming”).
Note:
Read the information in chapter
“KeyCard theft protection system”.
Extra function FMT
To store the six most powerful stations
automatically with Travelstore:
Press FMT until you hear a beep or
“T-STORE” appears in the display.
3
For instantly muting the volume.
Switching on/off via the ignition:
When connected correspondingly, the
set can also be turned on and off via
the vehicle ignition.
After the ignition has been switched
off, a double beep tone will remind you
that you should remove the KeyCard
before leaving your vehicle.
By pressing the
button the volume
will be muted immediately. “MUTE” will
appear in the display.
The function is cancelled by pressing
5 M•L - toggle switch
button
or VOL+.
To toggle between medium and long
wave reception.
When pressing VOL-, the normal vol-
ume will be by one grade lower than
the mute volume.
30
6 Rocker switch
Radio operation
Tape operation
Changer operation
/
Station search
Up
Down
/
Title selection (S-CPS)
Up
Down
CD selection
Up
Fast forward
Fast rewind
Down
<</>> Up/Down in short intervals when AF
is off
Title selection
Stop function by pressing
.
Upwards: Press briefly.
CUE - fast advance (audible):
<</>> To scroll through the station net-
works when AF is on,
Keep depressed.
e.g. NDR 1, 2, 3, 4, N-JOY, FFN,
ANTENNE ... .
Downwards: Press as many times
as required.
To restart a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
Extra rocker switch functions:
Further setting functions with
AUD
GEO
DSC MODE
PTY
J
I
H
>
Condition: The corresponding function
has to be activated.
31
f) lo
g) I, II, T
- Seek tuning sensitivity
- Memory bank I, II or
Travelstore
- Preset button (1-6)
- Loudness
- Stereo
- Alternative frequency for
RDS operation
7 Display
8 KeyCard theft protection system
To operate the set it is necessary that
the KeyCard is inserted.
h) 6
i) LD
j)
a
e
g h i
k
m n
f
j
l
KeyCard
k) AF
l) TP
- A traffic station is being re-
ceived
o
s
b
For this purpose, introduce the
KeyCard (with the contact area show-
ing up) into the slot above the tongue
sticking out of the unit.
To remove the card, press first to un-
lock.
m) TA
n) PTY
o) B
- Priority for traffic stations
- Programme type function
- Dolby B noise reduction
- A metal or CrO2 type is be-
ing played
- Radio-Monitor (to listen to
the radio during fast tape
winding)
r
q p
p) MTL
c
q) RM
Read also the information in chapter
“KeyCard theft protection system”.
d
r) BLS
s) MIX
- Blank-Skip (to skip un-
recorded tape portions)
- CD playback in random
order
Flashing KeyCard tongue
When the radio is turned off and the
KeyCard removed, the KeyCard
tongue can be programmed to flash for
optical theft protection.
For more information see chapter
“DSC programming”.
a) NDR2
b) TR 2
- Station name
- Track (side) 2 of the cas-
sette
c) VIVALDI - CD name or
d) 1 : 52
- CD time (playback time)
and number for changer
operation
This flashlight can be switched off by
pushing in the tongue and lock.
e) FM
- Waveband
32
9 MIX
Changer (CDC) operation
Preset Scan
< TA (priority for traffic announcements)
When “TA” lights up in the display, the
system will play traffic stations only.
Priority on/off: Press TA.
Press SC for approximately two sec-
onds until you hear a beep.
“SCAN” and the name of the scanned
station will alternately appear in the
display. The unit will scan all stations
stored on the preset buttons.
To stop Scan / Preset Scan:
Press SC once again.
MIX CD
The CD titles will be played at random.
The individual discs are selected in nu-
meric order.
= AF
Alternative frequency during RDS op-
eration:
When “AF” lights up in the display, the
system will automatically seek a fre-
quency offering better reception of the
same RDS programme.
MIX MAG
The CD titles will be played at random.
The individual discs are also selected
in random order.
Changer operation
CD-Scan
Press SC.
AF on/off: Press AF briefly.
MIX OFF
The Mix function is deactivated.
“CDC-SCAN” will appear in the dis-
play.
All CD titles will be scanned briefly.
To stop CD-Scan:
Press SC once again.
Regional function on/off:
Press the AF button for approximately
two seconds until you hear a beep.
“REG-ON” or “REG-OFF” will appear
in the display (see chapter REG - re-
gional programme).
Press MIX as many times until the de-
sired function briefly appears in the
display.
; lo
: SC
To switch the seek tuning sensitivity
level:
Press button briefly.
To switch between mono and stereo
reception:
> PTY (Programme Type)
Radio operation
In the PTY mode, the preset buttons
become programme type buttons. With
each preset you can select one pro-
gramme type, such as for example
NEWS, SPORT, POP MUSIC, EDU-
CATE, etc.
Scan
Press SC briefly –
“FM SCAN” and the name of the
scanned station will alternately appear
in the display. The unit will scan all
stations which can be received.
Press button for approximately two
seconds (beep).
The stereo symbol
mono playback.
will disappear for
33
? SRC (source)
When this function has been activated, D Cassette loading slot
You can switch between the different
audio sources radio, tape, and CDC.
“RM” shows on the display panel.
The radio is played back during fast
tape run.
Insert the tape with side A or 1 facing
up, the open side showing to the right.
@ DIS
E
Tape side selector
B
Press this button to switch over to the
other side during tape operation. The
display shows “TR 1” or “TR 2”.
Radio operation
Press to eject the tape.
When pressing the DIS button, the fre-
quency will be displayed for approxi-
mately four seconds.
C 1, 2, 3, 4, 5, 6 - preset buttons
On FM, you can store six stations for
each of the memory banks I, II and T.
On MW/LW, you can store six stations
each.
F B
Dolby B NR*
Press this button to play back a tape
which has been recorded with Dolby-B
noise reduction. When this button is
pressed, „B“ lights up in the display.
Tape operation
When pressing the DIS button, the sta-
tion name/frequency will be displayed
for approximately four seconds.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
waveband. On FM, also adjust the
corresponding memory bank. Then
press the relevant preset button briefly.
*
Noise Reduction system manufactured under li-
cense from Dolby Laboratories Licensing Cor-
poration. „Dolby“ and the double-D symbol are
trademarks of Dolby Laboratories Licensing Cor-
poration.
Changer operation
To switch the display mode and select
between name, time (playback time)
and number (disc number):
G LD
Loudness - When listening at a low
•
Press DIS briefly.
level, the Loudness function creates a
more natural sound by boosting the
low frequency range.
Extra function preset buttons
To store and recall a PTY programme
type.
A RM (Radio Monitor)
Press this button to listen to the radio
while fast forwarding or rewinding the
tape.
LD on/off: Press the button.
When the Loudness function is active,
“LD” will light up in the display.
See chapter “DSC programming” for
more information.
On FM, you can store and recall one
programme type on/from each preset
button when PTY is active (“PTY”
lights up in the display).
To switch RM on/off: Press RM.
34
H DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and prefer-
ences. See chapter “DSC program-
ming” for more information.
Extra function GEO
Separate balance and fader settings
for traffic messages. See chapter “Ad-
justing GEO for traffic messages and
the warning beep”.
J AUD
I GEO
To adjust the treble and bass frequen-
To adjust the balance (left/right) and
fader (front/rear) with the rocker
switch.
cies with the rocker switch.
Treble +
Treble –
Bass –
Fader front
Fader rear
Bass +
Balance left
Balance right
The last setting will be stored automat-
ically.
The last setting will be stored automat-
ically.
To switch off AUD: Press button once
again.
To switch off GEO: Press button once
again.
If the setting remains unchanged
within four seconds, the display will
switch back to the previous condition.
If the setting remains unchanged with-
in four seconds, the AUD setting will
be terminated automatically.
35
Important notes
Installation
Accessories
Precautions
If you would like to install your new car ster- Use only the accessories and spare parts
eo yourself or add other audio components approved by Blaupunkt.
to existing ones, then please read carefully
Before starting to use your new car radio,
please read the following information care-
fully.
the enclosed instructions on installation and You can use the following Blaupunkt prod-
connection.
In order to ensure that the set operates prop-
ucts with this car stereo:
Traffic safety
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car
radio in a way that could distract you.
Please keep in mind that you travel a dis-
tance of 14 m per second at a speed of only
50 km/h.
erly it is necessary that the positive power Remote control
supply line is connected via the ignition and With the infrared remote control RC 05 you
the permanent +12 V lead.
Do not ground the loudspeaker outputs!
can control all of the important functions of
your car hi-fi system from the steering wheel.
Telephone mute
If you have a mobile telephone installed in
your vehicle, radio, tape or changer play-
back can be muted automatically when us-
ing the phone (telephone mute).
“PHONE” will then appear in the display.
When TA is active, traffic messages will al-
ways have priority. The announcement will
be aborted by pressing the TA button.
Should the traffic situation become particu-
larly demanding, we advise you not to use
the radio.
Always make sure that you are still able to
hear any warning signals coming from out-
side of the vehicle, such as police or fire
engine sirens, so that you can react ac-
cordingly.
Therefore, you should always select a
moderate volume for playing your car radio
while you are driving.
Amplifier
All Blaupunkt amplifiers
36
KeyCard theft protection system
This car radio is supplied with one KeyCard ERR” will appear in the display. In this case
•
Press << or >>.
as standard, though it can also be operated please do not make any further adjustments.
The display will switch to “CHANGE”.
with a second card.
The system will switch off after approxi-
•
•
Push in the KeyCard. The card is re-
leased and put in the proper position
for being removed.
If you have lost your KeyCard or if it was mately ten seconds.
damaged, you can buy a new one from your When inserting another card type (e.g.
specialised dealer.
phone or credit card), the display will show
Remove the first KeyCard and insert
the new one while “CHANGE” is still
being displayed.
When using two KeyCards, the settings “WRONG KC” for approximately two sec-
stored on the first card will be adopted. How- onds.
ever, you can individually store the follow- Remove the wrong card and introduce the
After the display indication “READY” or
“LEARN KC”,
ing functions:
correct KeyCard.
Preset button assignments, bass, treble, After the display indications “CARD ERR”
balance and fader settings, Loudness, TA or “WRONG KC”:
•
press DSC.
Now you can also use the new KeyCard for
operating your unit.
(traffic announcement volume), beep vol-
ume.
•
Press ON to turn on the set.
A maximum of two cards can be used for
the set.
When trying to “train” a third one, the ac-
cess authorisation for the KeyCard not used
for the “training” process will be deleted
automatically.
In addition, the settings activated before
switching the radio off, such as the wave-
band, station, TA priority, AF, REG ON/OFF,
SCANTIME, seek tuning sensitivity and VOL
FIX will also remained stored.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
Removing the KeyCard
Never pull out the KeyCard directly!
•
First, slightly push in the KeyCard.
This releases the card and puts it in the
proper position for being removed.
•
Now you can pull it out.
Displaying the radio pass data
“Training” a second KeyCard/
Using the KeyCard supplied with your set
you can have the radio pass data such as
the model name, product number (7 6 ...)
and serial number indicated on the display
panel.
Putting the unit into operation
Replacing a KeyCard
While operating the unit with the first
KeyCard, you can “train” a second one to
be also used with the set:
•
Turn on the set.
Introduce the KeyCard into the slot
with the contact area showing up
(KeyCard tongue sticking out).
Please refer to chapter “DSC programming
- READ KC”.
•
Insert the first KeyCard and turn on the
set.
The car radio is now ready for operation.
If a wrong KeyCard is inserted, then “CARD
•
Press the DSC button and select
“LEARN KC” with
/
.
37
Switching the audio source
Short Additional Memory
(S.A.M.)
Optical indication for extra
security
Using the SRC button you can switch be-
tween the following audio sources:
radio,
The second KeyCard available from your Flashing KeyCard tongue
specialised dealer offers you the possibility
tape,
When the vehicle is stationary and the
to read out any short information, which will
be moved through the display, such as, for
example, the phone number of your car deal-
er or the emergency call number of your
automobile association. Please refer to
chapter “DSC programming - READ KC”.
The freely selectable text with a maximum
of 48 characters can be programmed by all
dealers who have the required equipment
available.
KeyCard removed, the KeyCard tongue can
be switched to flash for extra anti-theft secu-
rity.
For this it is necessary that the positive pow-
er supply line and the permanent +12 V lead
are connected such as described in the in-
stallation instructions.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming - LED”.
changer.
Tape operation is only available if a cassette
is inserted.
To switch to another source,
•
press SRC briefly.
Turn On Message (T.O.M.)
Switching off the flashlight
The second KeyCard available from your
specialised dealer also allows you to dis-
play a special turn-on message each time
the radio is switched on.
The freely selectable text with a maximum
of 48 characters can be programmed by all
dealers who have the required equipment
available.
The flashlight can be switched off by push-
ing in the KeyCard and lock.
If you would like to deactivate the flashing
tongue with general effect, adjust the rele-
vant item in the DSC menu to “LED OFF”.
Care of your KeyCard
The programmed text will be displayed each
time you turn on your system with the sec-
ond KeyCard.
For a proper function of the KeyCard it is
important that the contacts are free from any
foreign particles. Avoid direct skin contact.
If necessary, clean the KeyCard contacts
using a cotton swab soaked with alcohol.
38
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more If “SEARCH” appears in the display when If you leave the service area of the regional
convenience when listening to FM radio sta- switching on the radio or recalling one of the programme tuned into, or if you would like
tions.
stored frequencies, the unit is automatically to take advantage of the full RDS service,
More and more radio stations have begun searching for an alternative frequency.
switch to “REG OFF”.
to broadcast RDS information alongside “SEARCH” will disappear from the display
•
Press the AF button for approximately
two seconds until “REG OFF” appears.
their programmes.
when the alternative frequency has been
As soon as a programme has been identi- found or after the frequency band has been
fied, the station name including a regional run through completely.
identifier, if applicable, will appear in the dis- If the reception quality of the selected pro-
play, for example, NDR1 NDS (regional pro- gramme becomes too bad:
“REG ON” or “REG OFF” will be briefly dis-
played each time the radio is switched on.
Selecting a waveband
gramme in Lower Saxony, Germany).
When RDS is activated, the preset buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired sta-
tion quickly.
•
Tune into another station.
With this car radio you can select between
the following wavebands:
FM 87.5 - 108 MHz
REG - regional programme
Certain radio programmes are split up at MW 531 - 1602 kHz
times into regional programmes offering lo- LW 153 - 279 kHz
But RDS offers you further advantages:
cal information. The 1st programme broad-
cast by NDR, for example, offers pro-
grammes with different contents in the
northern states of Germany Schleswig-
Holstein, Hamburg and Lower Saxony at
certain times of the day.
If you are listening to one programme and
move to an area where another linked re-
gional programme becomes stronger, the
unit will switch to that programme.
•
Select the desired waveband by press-
ing the FMT or M•L button.
AF - Alternative frequency
To toggle between MW and LW:
Press M•L.
•
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
Station tuning
Automatic tuning
/
•
Press
cally search for the next station.
When keeping the upper or lower part
/
; the car radio will automati-
In order to switch this function on or off,
If you wish to continue listening to the first
programme,
/
•
press the AF button briefly.
of the rocker switch depressed, seek tuning
will speed up in upwards or downwards di-
rection.
•
press the AF button for approximately
two seconds.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
“REG ON” appears in the display.
39
Scrolling through the broadcast-
ing networks (only FM)
•
Press the FMT button as many times
until the desired memory bank lights
up in the display.
You can use the << >> buttons to tune in
stations of your reception area.
Storing stations
If several programmes of the broadcasting
networks can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...
For this it is necessary that the stations have
been tuned in at least once and that “AF” is
active (lights up in the display).
On FM, you can store six stations on the
preset buttons 1-6 for each of the memory
banks I, II and T.
Seek tuning
Up
Down
Down in short intervals
(“AF” must be switched off)
Up in short intervals
(“AF” must be switched off)
On MW/LW, you can store six stations each.
•
•
Select the appropriate waveband with
FMT or M•L.
Tune in a station with the rocker switch
For this purpose, you may start Travelstore
seek operation:
(either automatically
<< >>).
/
or manually
Manual tuning with << >>
•
Press FMT for two seconds; the sys-
tem starts to run through the frequency
band.
•
Press the desired preset button until
the radio resumes play after the mut-
ing (takes approximately two seconds,
confirmed by beep).
You can also tune in a station manually.
Condition:
If “AF” does not light up,
press AF.
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
•
Now the station has been stored.
The activated preset button is indicated in
the display.
With this, the requirements for selecting sta-
tions with << >> are fulfilled.
If necessary, deactivate these functions:
•
Press AF or PTY.
Changing the memory bank (FM)
Manual tuning:
Notice:
Should you tune in a station which has al-
ready been stored before on another
memory bank, the corresponding preset
button and the memory bank will briefly flash
in the display.
You can shift between the memory banks I,
II and T in order to store stations and recall
them later.
The currently selected memory bank is in-
dicated in the display.
•
Press << >>; the frequency will change
in short intervals in downwards or up-
wards direction.
When holding the right or left part of the rock-
er switch depressed, the frequency scan is
speeded up.
40
Automatically storing the
strongest stations with
Travelstore
Scanning stored stations with
Preset Scan
To select a scanned station and switch
off the Radio-Scan function:
•
Press SC briefly.
You can have all of the stored stations briefly
If no station is selected, the scan function
will be automatically switched off after the
frequency band has been run through com-
pletely. The unit will tune in the station lis-
tened to before starting the scan.
You can automatically store the six most scanned on all wavebands.
powerful FM stations of your current recep-
tion area sorted according to their signal
strength. This function is particularly con-
venient on longer trips.
To start Preset Scan:
•
Press SC for approximately two sec-
onds.
All of the stored stations of the adjusted
waveband will be scanned one after the oth-
er. The memory bank and preset position of
the currently scanned station will flash in the
display.
•
Press the FMT button for two seconds.
Changing the scan time
“T-STORE” will appear in the display.
The six strongest FM stations will be auto-
matically stored on the memory bank “T”
(Travelstore). When this process has been
completed, the radio will play the first sta-
tion.
If desired, stations can also be stored
manually on the Travelstore bank (see “Stor-
ing stations”).
The scan time can be changed from be-
tween five to a maximum of 30 seconds.
Please refer to chapter “DSC programming
- SCANTIME”.
To select a scanned station and switch
off Preset Scan:
•
Press SC briefly.
Selecting the seek tuning sensi-
tivity
Scanning stations with Radio-
Scan
You can alter the automatic seek tuning
sensitivity.
Recalling stored stations
You can also scan all stations which can be
received.
If “lo” is displayed, the radio will only pick up
strong, local stations (low sensitivity).
If “lo” does not light up, the radio will also
pick up weaker, distant stations (high sen-
sitivity).
The sensitivity level can be altered in both
modes (see also chapter “DSC program-
ming”).
You can recall any stored station at the touch
of a button.
To start the Scan function:
•
Select the waveband by pressing FMT
or M•L. On FM, also choose the corre-
sponding memory bank by pressing
the FMT button as many times until the
desired bank appears in the display.
•
Press SC briefly.
The scanned frequency or the station name
will start flashing in the display. During the
actual scanning process “FM-SCAN” or
“AM-SCAN” will be displayed.
•
Press the corresponding preset button
briefly to recall the station.
41
Switching from stereo to mono
(FM)
Programme type
Checking the programme type of the
station
Use << >> to have the last selected pro-
•
Press PTY for approximately two sec-
If reception is poor, you may get better gramme type displayed and to choose a new
onds.
sound quality by switching to mono:
one.
You can select any one of the stored types
with the preset buttons 1 - 6.
Condition: PTY must be active.
Using DSC you can choose between Ger-
man and English (see “DSC programming -
PTY LANG”).
All of the programme types listed below are
available.
The letters printed in bold are identical to
the actual short-time indication in the dis-
play.
After the beep tone the display will show the
programme type offered by the tuned in sta-
tion.
If “NO PTY” appears in the display, the cur-
rent station has no PTY code.
•
Press the lo button for approximately
two seconds.
With mono playback, the stereo sign will
disappear from the display.
Each time the radio is switched on, stereo
playback is activated.
The unit will automatically switch to mono if
the received signal is not strong enough for
stereo playback.
Displaying the selected programme
type
•
Press << or >>.
The programme type selected last will be
displayed briefly.
PTY – Programme Type
NEWS
PTY is an RDS service offered by more and
more radio broadcasters. This feature allows
you to select FM stations according to their
programme type. After you have chosen the
PTY of your preference, the corresponding
stations can be selected either by seek
tuning or using the scan function.
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
Selecting a programme type
a) Using the preset buttons
When PTY is switched on, you can use
the preset buttons 1-6 to select the
programme types stored at the factory.
CULTURE
SCIENCE
•
Press one of the presets 1 - 6.
The selected programme type will be
displayed for two seconds.
VARIED
POP MUSIC
Switching PTY on/off
ROCK MUSIC
•
Press PTY.
If you wish to listen to a station with
this PTY,
M.O.R. M (middle of the road music)
LIGHT M (light classical)
CLASSICS (serious classical)
OTHER M (other music)
When the function is active, the programme
type selected last will briefly appear in the
display. “PTY” will be permanently indi-
cated in the lower right corner of the display
panel.
•
press
/
to start seek tuning op-
eration.
PTY 16 to PTY 30 are not yet assigned.
42
If the system is unable to find a station of- will be released. The station received be- PTY priority
fering the selected programme type, the dis- fore starting seek tuning will be tuned in.
play will show “NO PTY” and a beep tone
will be released. The station received be- Storing programme types
Situation:
PTY is switched on and lights up in the dis-
play.
fore starting seek tuning will be tuned in.
One programme type was assigned to each
No station offering the selected programme
type can currently be received (with seek
tuning or scan).
The set will switch back to the previous sta-
tion.
As soon as a programme with such PTY can
be received within the broadcasting network,
the unit will switch over to the correspond-
ing station for the duration of the pro-
gramme.
You can assign different programme types
to each preset position. Please refer to the
next chapter “Storing programme types”.
of the preset buttons 1-6 at the factory.
If desired, you can also store other availa-
ble programme types.
To do so, make sure that “PTY” lights up in
the display.
b) Using the << >> buttons of the rocker
switch
•
•
•
If necessary, press the PTY button to
switch on the function.
When PTY is switched on, you can se-
lect a programme type using buttons
<< >>.
Select a programme type using but-
tons << >> and
•
•
•
Press << or >>; the programme
type selected last will be displayed
for three seconds.
hold down the desired preset button
(1-6) until you hear a beep.
Example:
German broadcasting network NDR:
Now the selected programme type can be
recalled by pressing this preset. For this the
PTY function must be active.
-
-
-
-
-
Station tuned in: NDR3.
During this period press >> (for-
wards) or << (backwards) to select
the desired type.
“PTY” lights up in the display.
Programme type “POP” selected.
Seek tuning is started.
Press << or >> as many times as
required.
Scanning stations with PTY-SCAN
Condition: “PTY” must appear in the display.
No station with “PTY-POP” can be
If you wish to listen to a station offering
the selected PTY,
•
Press the SC button.
found.
All received stations offering the selected
programme types will be scanned.
-
-
-
-
The display shows “NO PTY” and
automatically switches back to NDR3.
NDR2 airs a “PTY-POP” programme.
•
press
/
to start seek tuning op-
eration.
To switch off PTY-SCAN:
If the system is unable to find a station of-
fering the selected programme type, the dis-
play will show “NO PTY” and a beep tone
•
Press SC once again.
The system will switch to the linked
station NDR2 for the duration of the
“POP” programme.
43
Receiving traffic programme stations with RDS-EON
During tape or CDC operation, the set will The abbreviation “EON” stands for En- Traffic announcement priority
also automatically switch to the programme hanced Other Networks, meaning the on/off
offering the selected PTY within the broad- exchange of information within a radio net-
If the priority for traffic announcement pro-
grammes is activated, “TA” will light up in
the display.
casting network.
work.
After the PTY programme the system will Many FM broadcasters offer traffic messag-
remain in the radio mode.
es for their service area at regular intervals.
All traffic programme stations transmit a
special carrier signal alongside their pro-
To switch the priority on or off:
•
Press the TA button.
Notice:
When pressing TA while a message is be-
ing broadcast, this message will be interrup-
ted. The unit will then switch back to the pre-
vious condition. The priority for other traffic
messages remains active.
Please note that several buttons have no
function while a traffic announcement is
broadcast.
As earlier mentioned, these functions are grammes, which is decoded by your car ra-
currently only supported by a limited number dio. If this signal is identified, “TP” will ap-
of RDS stations.
pear in the display (Traffic Programme).
In addition to these, there are also stations
which do not actually transmit traffic pro-
grammes themselves, but by using RDS-
EON they offer the possibility to receive the
traffic messages broadcast by another traf-
fic programme station in the same radio
network.
Warning beep
If you wish to have the priority for traffic an-
nouncements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic programme station (in this case,
NDR2) for the duration of the message and
return to the original programme (NDR3)
afterwards.
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a warning beep after approximate-
ly 30 seconds.
This alarm tone will also be released when
pressing a preset button which has no traf-
fic programme allocated to it.
44
Switching the warning beep off
Adjusting the volume for traffic
announcements and the warning
beep
a) Tune into another station offering traf-
fic information:
This volume was preset at the factory,
though you can alter the value using the
DSC function (see “DSC programming, TA
VOL”).
•
•
Press the rocker switch or
press a preset button which has a
traffic programme station allocated
to it.
Alternatively:
Adjusting GEO for traffic mes-
sages and the warning beep
b) Switch off the priority for traffic an-
nouncements:
You can separately adjust the balance and
fader settings for both traffic announcements
and the warning beep.
•
Press TA.
“TA” will disappear from the dis-
play.
For example, it is possible to listen to traffic
reports via the front left (right) speaker only.
This provides the driver with the important
traffic information without bothering the rear
passengers too much.
Automatic seek tuning start
(tape and CD changer operation)
When leaving the reception area of the
tuned in traffic programme station while
listening to a tape or CD, the system will
automatically start searching for a new TA
programme.
If no such station is found within approxi-
mately 30 seconds, tape or CD operation
will be stopped and a warning beep will
sound. To switch the warning beep off, pro-
ceed as described above.
To make a setting:
•
During an announcement, adjust the
balance and fader settings to suit your
personal preferences.
45
Tape operation
Fast Forward/Rewind
portion of at least three seconds between
the individual titles.
The car stereo has to be switched on.
The unit automatically switches to tape op-
eration when a cassette is inserted.
Switching the tape side
(autoreverse)
Inserting a tape
To change the tape direction during cassette
playback:
•
•
Turn on the set.
Insert a tape.
•
Press
.
Fast forward
Fast rewind
The tape will be automatically transported
to the playback position. Side A or 1 starts
to play.
During tape operation, “TR 1” or “TR 2”
(track) will show on the display panel.
At the end of a tape side, the mechanism
changes directions automatically to play the
other side (autoreverse). The display shows
“TR1-PLAY” for track (side) 1 or “TR2-PLAY”
for track 2.
/
Title selection (S-CPS)
Up
Down
Stop function by pressing
.
Insert the tape with side A or 1 facing up, the
open side showing to the right.
Notice:
Selecting titles with S-CPS
If there is too much tension on the tape
during playback, the set may switch over by
itself before having reached the end of the
tape side. In this case check the condition
of the cassette tape. Sometimes it helps to
rewind it completely.
(Super Cassette Programme Search)
Use this function to skip ( ) and repeat ( )
recorded titles.
A maximum of nine titles can be skipped.
To do so,
Removing a tape
•
press the rocker switch as many times
as required.
•
Press
.
Tape equalisation
The cassette will eject.
The number of titles to be skipped appears
on the display panel.
If necessary, you can correct your entry by
pressing the opposite rocker switch button.
When a metal or CrO2 tape is inserted, the
tape mechanism automatically adjusts to
metal/CrO2 tape equalisation.
The “MTL” indicator will illuminate.
Stop by pressing
.
For a proper operation of the S-CPS func-
tion there has to be an unrecorded tape
46
Scanning cassette titles with
SCAN
Skipping unrecorded tape por-
tions with Blank Skip
Care notes
To avoid possible problems, we recommend
You can have the cassette titles played brief- This function senses an unrecorded tape you to use C-60/C-90 type cassette tapes
ly by using the scan function. If you like a portion continuing for more than 15 seconds only. Store your tapes in a cool place away
title, stop the scan to continue listening to and automatically fast forwards the cassette from dirt, dust and temperatures exceeding
that track.
to the beginning of the next track.
During fast tape winding, “B-SKIP” will be up before playing them in order to avoid
indicated on the display panel.
50 °Celsius. Allow very cold tapes to warm
To start/stop the scan function:
uneven tape transport. After approximately
100 hours of use, dust particles collected
on the playback head or roller may lead to
tape run problems and sound distortions.
Use a head cleaning tape to remove nor-
mal dirt build-up. For tougher cases, use a
cotton swab (Q-Tip) soaked with alcohol. Do
not attempt to clean by inserting a hard ob-
ject into the player!
•
Press the SC button briefly.
To switch the Blank Skip function on and
off:
You can individually adjust the scan time in
the DSC menu (see “DSC programming -
SCANTIME”).
•
Press the RM button for approximately
one second until you hear a beep.
When the function has been activated, “BLS”
will appear in the display.
Dolby B NR*
With this unit you can play back tapes re-
corded with Dolby-B NR or without noise
reduction.
Cassette tapes recorded with Dolby NR*
stand out by their reduced tape hiss and the
improved dynamics.
Listening to the radio during fast
tape winding with RM
(Radio Monitor)
When the tape is fast forwarded or rewound
If Dolby-B NR is switched on, “B” will light (also with S-CPS), the radio will normally
up in the display.
be muted. To listen to the radio during fast
winding, activate the Radio Monitor function.
To switch RM on and off:
To switch on/off:
•
Press RM.
•
Press B (not during scan operation).
When the function is active, “RM” will light
up in the display.
*
Noise Reduction system manufactured under license
from Dolby Laboratories Licensing Corporation. “Dol-
by” and the double-D symbol are trademarks of Dol-
by Laboratories Licensing Corporation.
47
CD changer control A05
Switching to CDC operation
MIX playback
Selecting the display mode
Make sure that at least one CD has been You can have the CD tracks played in ran- You can select the desired display mode for
inserted into the magazine.
dom order.
CD operation:
Press SRC to go through the available au-
dio sources:
MIX CD – The titles of the selected CD
will be played at random.
“NAME”
– The specified name, for
example “MADONNA”
will be displayed.
•
Press as many times until the display
The next disc will be select-
ed in numeric order.
briefly shows “CDC ON”.
“TIME”
– The elapsed playback
time of the title is dis-
played, for example
“2 : 32”.
MIX MAG – All CD titles will be played at
random.
Selecting CDs and titles
The next disc will then also
be selected and played ran-
domly, etc.
“NUMBER” – The CD position in the
magazine (disc number)
is displayed, for example
“CD8 T5”.
MIX OFF – The Mix function is deactivat-
ed. Discs and titles will be
selected in numeric order.
To switch the display mode:
•
Press DIS during CD playback.
CD selection
Up
To alter the setting:
The display mode and the corresponding
setting or value will briefly show on the dis-
play panel, e.g. “TIME”, “2 : 32”.
•
Press MIX as many times until the de-
sired function is briefly displayed.
Down
If the function is active, “MIX” will appear in If you have selected “NAME” without hav-
the right display corner.
ing specified a name for the corresponding
disc, “CD PLAY” will appear in the display.
Please read also the chapter “Entering CD
names”.
Title selection
Upwards: Press briefly.
CUE - fast advance (audible): Keep
depressed.
Downwards: Press as many times as
required.
To restart a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
48
Storing the display mode
Entering CD names
Deleting CD names with
DSC-UPDATE
You can store your preferred display mode You can name up to 99 discs.
which will then be active each time the ra- The specified name (e.g. VIVALDI) will then You can delete a CD name with the help of
dio is switched on.
If required,
appear in the display.
the DSC update function. Use “CDC UPD”
Be sure to select the display mode “NAME” to confirm all of the CDs for which the spec-
using the DIS button.
ified name is not to be deleted.
•
press DIS as many times until the de-
sired setting is displayed.
•
Insert a magazine with CDs for which
the stored information is to be main-
tained.
To start the entry:
•
Hold down the DIS button until you
hear a beep.
•
Press the DSC button.
“CDC-NAME” will be displayed.
•
•
•
Press the DSC button.
•
Press
.
Press
/
to select “CDC UPD”.
SCAN operation
The first underscore character will flash.
•
Select the first character with the help
of the rocker switch / .
Press << >>.
Use this function to scan all of the CD tracks.
After the update has been completed,
You have the choice between the capital “NEXT MAG” appears in the display.
To start the Scan function:
•
Press SC.
letters A to Z, special characters and the
numbers 0 to 9.
•
Press the button on the changer for
approximately two seconds.
The titles will be scanned one after the oth-
er in ascending order.
•
Use the rocker switch << >> to move
to the next underscore and select a
character.
The magazine will eject.
Insert the next magazine.
To stop the Scan function:
•
•
Press SC briefly.
Proceed as described above for all of the
CDs/magazines for which the entered name
is to be maintained.
You can select up to seven characters.
Once you have completed the name as de-
sired:
The track currently being scanned is con-
tinued to be played.
SCAN will also be terminated by
•
After having updated the last maga-
zine, press
To quit the function,
press DSC.
•
Press
To quit the naming mode,
leave the DSC menu by pressing DSC.
If you would like to name another CD,
select a new disc.
in order to store it.
.
•
pressing one of the buttons AUD,
GEO, DSC, SRC, , << >> or / .
•
•
The system has saved the name informa-
tion for all of the CDs which were inserted.
•
You can change any existing name by en- For all other discs the CD names have been
tering and storing a new one (overwriting). deleted.
49
DSC programming
CDC NAME Only available for CD
changer playback.
SPEECH
In future many RDS radio
stations will differentiate be-
tween music and speech
programmes.
You can alter the tone for
speech programmes from
between “SPEECH 0 ... 4”.
DSC (Direct Software Control) allows you
to customise certain programmable, basic
settings to suit your personal needs and
preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to these if desired.
Use this function to name
your CDs. (See “Entering
CD names”).
LOUDNESS Loudness - When listening
at a low level, the Loudness
function creates a more nat-
ural sound by boosting the
low frequency range.
SPEECH 0:
Music/speech off
If you wish to alter any of the programming,
SPEECH 1:
•
press DSC.
Linear reproduction (bass,
treble and Loudness set to
“0”)
LOUD 1 - Low boost
LOUD 6 - Max. boost
Use the rocker switch and the
button to
select and adjust the functions described in
the following. The display will show you the
adjusted condition.
SPEECH 2-4:
TA VOL
To adjust the traffic an-
nouncement and warning
beep volume from between
0 to 63.
Different settings for vol-
ume, bass and treble with
the Loudness being
switched off.
The message will then come
through at this volume, if the
standard volume is lower.
Should the standard volume
be higher than the TA VOL
level, then the traffic report
will be played slightly louder
than the standard volume.
Try out which SPEECH set-
ting you like most.
/
Select function
Adjust/recall value
<< >>
50
BEEP
Acknowledgement tone for
all functions which require a (Variocolour) For gradually matching the
COLOUR
READ KC
To read out the KeyCard
data.
button to be pressed for
more than one second.
The volume can be adjusted
from between 0 to 9. (0 =
off).
radio illumination with the
dashboard lighting.
The card supplied with the
radio is used to display the
model name, type number
(7 6..) and the serial
green ..............light orange................. red
number.
LED ON
Here you can choose be-
tween LED ON or LED OFF.
With LED ON, the KeyCard
tongue will flash for extra
anti-theft protection when
the unit has been switched
off and the KeyCard re-
moved.
With the extra card it is pos-
sible to display the Short
Additional Memory (S.A.M.)
data entered by your spe-
cialised dealer. See chapter
“Short Additional Memory
S.A.M.”.
If you remove the KeyCard
during the reading process,
“READ KC” will show on the
display panel. The unit con-
tinues to play but does not
accept any operations ex-
cept from being switched
off. Re-insert the card.
ANGLE
BRIGHT
Use this setting to alter the
viewing angle to your liking
from -1 to 0 to +1.
You can adjust the display
brightness from between 1
to 16. You can also select
different values for day and
night.
LEARN KC To “train” a second
KeyCard.
Please read the information
in chapter “KeyCard theft
protection system - “Train-
ing” a second KeyCard”.
Selecting the night bright-
ness:
Switch on the vehicle lights
and programme the bright-
ness value. The car radio’s
lighting connector must be
hooked up to the vehicle’s
electric system for this to
function properly.
PTY LANG To select the programme
type language:
DEUTSCH or ENGLISH
51
SCANTIME Use this function to set the
scan time for the radio or
CDC UPD
Use this function to delete
CD names during CDC op-
eration, in order to have
more storage capacity for
new discs available. See
“Deleting CD names with
DSC-UPDATE”.
Overview of the DSC factory
settings
CD player from between five
and 30 seconds.
CD NAME
LOUDNESS
TA VOL
-
3
35
S-DX
S-LO
To adjust the seek tuning
sensitivity for distant recep-
tion.
DX 1 - high sensitivity
DX 3 - low sensitivity
SPEECH
BEEP
0
4
ANGLE
0
BRIGHT
COLOUR
LED
16
green
ON
VOL FIX
Use this function to select
the volume at which the ra-
dio is set when it is switched
on. Adjust the desired vol-
ume level with << >>. When
adjusted to “VOL 0”, the
system will come on with the
volume selected before
LEARN KC
READ KC
PTY LANG
SCANTIME
S - DX
S - LO
CD UPD
VOL FIX
-
-
To adjust the seek tuning
sensitivity for local recep-
tion.
ENGLISH
10 sec.
1
1
-
LO 1 - high sensitivity
LO 3 - low sensitivity
The seek tuning sensitivity
values can be separately set
for AM and FM.
switching the radio off.
To quit the DSC programming mode
and store the adjustment:
0
•
Press DSC.
52
Appendix
Specifications
Blaupunkt
telephone hotline
Amplifier
Output power:
4 x 23 W RMS power
acc. to DIN 45324 at
14.4 V
Address of the next service
centre in your vicinity
(only for Germany)
4 x 35 W max. power
Tuner
Wavebands:
If you would like to know the address of
the next Blaupunkt service centre of
your area without having our service list
at hand:
FM
MW
LW
:
:
:
87.5 – 108 MHz
531 – 1602 kHz
153 – 279 kHz
FM sensitivity:
0.9 µV at 26 dB
signal-to-noise ratio
-
-
Find out your area code.
Then call the following chargeable
phone number: 01 80 / 5 25 56 66.
FM frequency response:
30 - 16 000 Hz
-
Using the area code to be entered
you will be automatically given the
address and phone number of the
next Blaupunkt service centre. You
can also request this information
by fax.
Tape player
Frequency response:
30 - 18 000 Hz
CD player
Frequency response:
5 - 20 000 Hz
Subject to modifications!
53
|