AC603A
Mini Cat5 VGA Transmitter
With Local Port
Transmit VGA, HDTV Component Video, or
Composite Video via UTP Twisted Pair Cable
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
Web site: www.blackbox.com
•
E-mail: [email protected]
UMA1105 Rev. n/c
Mini Cat5 VGA Transmitter w/ Local Port
Trademarks Used in this Manual
BLACK BOX and its logo
are registered trademarks of Black Box
Corporation. Any other trademarks mentioned in this manual are
acknowledged to be the property of the trademark owners.
FCC and Canadian Dept of Communications Radio
Frequency interference statements
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio
communication. It has been tested and found to comply with the limits
for a Class A computing device in accordance with the specifications in
Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which case the user
at his own expense will be required to take whatever measures may be
necessary to correct the interference. Changes or modifications not
expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio
noise emission from digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe
A prescrites dans le Règlement sur le brouillage radioélectrique publié
par le ministère des Communications du Canada.
European Union Declaration of Conformity
This product complies with the requirements of the European EMC
directive 89/336/EEC
1
Model AC603A
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el
aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia
futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación
deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina
de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean
recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su
uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie
similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que
impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)
que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del
equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados
ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular
atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones
del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de
energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por
un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados
sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
2
Mini Cat5 VGA Transmitter w/ Local Port
Contents
1. Introduction ..............................................................................page 4
1.1 General ................................................................................page 4
1.2 Features ...............................................................................page 4
2. Installation .................................................................................page 5
2.1 Setup Connections ...............................................................page 5
2.2 Dip Switch Settings .............................................................page 6
3. Troubleshooting.........................................................................page 7
4. Specifications.............................................................................page 8
5. Appendix ...................................................................................page 9
EIA/TIA 568B WIRING STANDARD
3
Model AC603A
1. Introduction
1.1 General
The AC603A extends video + phantom power over UTP (Cat5/5e/6)
cable up to 500 feet. The unit has a local output port on an HD15
connector. The AC603A can support the following video signals
ꢀ
ꢀ
PC’s VGA video (RGBHV) at any resolution
Component video (Y Pb Pr, or RGB), at any resolution - an
adapter cable HD15-to-3RCA will be required
ꢀ
NTSC, PAL, or SECAM Composite video and stereo audio -an
adapter cable HD15-to-3RCA (video and R/L Audio) will be
required
At the receiving (remote) end the Cat5 signal is converted back to
VGA for connection to monitors, projector or other display devices
using a compatible unit (Black Box Model AC602A).
The AC603A includes a power supply that powers itself and the
AC602A Receiver (phantom power) for a clean and easy setup (note
that if the length of Cat5 cable is longer than 300 feet, the receiver may
require its own power supply). Alternatively, the power supply can be
connected to the AC602A remote receiver, in which case, the sender is
powered through the cat5 cable.
1.2 Features
•
•
•
•
•
Local VGA port available for local display
Differential signaling eliminates ground loops and noise
Handles resolutions up to 1600x1200 at any refresh rate
Rugged, Reliable, Compact size
Only one end requires power in most applications. Power supply
can be connected at the sending or the receiving end, whichever is
convenient.
•
Drive standard CAT5 cables to 500 feet (for VGA and Component
Video) or to 1200 feet (for Composite Video + Audio)
4
Mini Cat5 VGA Transmitter w/ Local Port
2. Installation
Figure 1 – AC603A Front
2.1 Setup Connections
1. Connect the VIDEO INPUT to the computer's video port using a
male-male VGA cable (not included).
2. If desired, connect a local display to the VGA out port of the
Transmitter unit.
3. Using Category 5 cables connect the RJ45 port of the Transmitter
to the Model AC602A Receiver.
4. Connect the Remote displays to the VGA output port of the
AC602 Receivers.
5. Plug in the supplied Power supply to the Power Input jack of the
Transmitter unit (can also be connected to Receiver instead).
6. Turn on the local and remote displays, then the PC
Note: If the source is Component Video (YPbPr) an HD15 to 3 RCA
cable will be required for each HD15 connector.
If the source is composite video with stereo audio, a similar
cable will be needed. The RCA connectors are typically yellow
(instead of green) for video and red/white for audio. To transmit
CV and stereo audio, you must set a dip switch per the
following section.
5
Model AC603A
2.2 Dip Switch Settings
The AC603A can be used to transmit Composite Video and Stereo
Audio instead of VGA to the receiver. However since the Video
signals are terminated differently than audio, you need to move the dip
switch to the proper position.
Use the Mode Dip Switch to select the video type for transmission.
The Sync Dip Switch is used to change the polarity of sync at the
receiver. If your remote display has trouble positioning the right and
left edges of the screen, then try putting the switch is +/+
NOTES
If the length of Cat5 Cable is longer than 300 feet you
may need to attach a power supply to the receiver unit. The
power supply will need to be the same as the sending unit (i.e.
9VDC regulated, Center Positive with 2.5mm connector). If there
is no image at the remote or the image is intermittent, you may
need a power supply at the receiver, please contact Black Box
to purchase one. Generally if the remote display device is
referenced to ground (i.e. the VGA connector ground or case, is
connected to power line ground) you should not need an
additional power supply to the specified maximum length of 500
feet
Do not connect this unit to any LAN device such as
network cards or hubs as this may damage the AC155A and/or
the LAN device. Use EIA/TIA 568B standard straight-through
patch wiring. Do not use crossover cables.
For cable runs of 300 feet or longer it is recommended
that you use a UTP cable that is optimized for video (low skew
cable).
We recommend Belden Cable’s “Brilliance®
VideoTwist(tm)” Category 5 Cable for best results.
6
Mini Cat5 VGA Transmitter w/ Local Port
3. Troubleshooting
1. Fuzzy, blurry, or ghosting image at remote location
If you have a stable image but it looks blurry (object or character edges
are smearing), adjust the compensation on the receiver. If you still have
a fuzzy image, try reducing the refresh rate and/or the resolution setting
of the video. For Best results use either low-skew cable (such as
Belden Brilliance® VideoTwist), or Cat5 (instead of Cat6).
2. Shaking image or periodically blanking monitor
A strong electromagnetic noise field can cause instability in the signal.
Usual sources of this form of noise coupling are high current AC lines
or other high-density data and/or control cables that run adjacent to and
parallel with a substantial length of the CAT5 cable.
To eliminate this, either separate the Cat 5 cable of Mini-CAT5
Extender from the interfering source or use shielded CAT5 cables.
Usually separating the CAT5 cable from the interfering source by a
few inches is sufficient to eliminate this problem.
If the length of Cat5 run exceeds 300 feet you may need an additional
power supply at the receiver.
Contacting Black Box
If you determine that your extender is malfunctioning, do not attempt
to repair the unit. Contact Black Box at 724-746-5500. Before you do,
make a record of the problem. We will be able to provide more
efficient and accurate assistance if you have a complete description.
Shipping and Packaging
If you need to transport or ship your extender:
• Package it carefully. Use the original container if possible.
• Before you shipping the unit, contact us to get a Return
Authorization (RA) number.
7
Model AC603A
4. Specifications
Video Types VGA through UXGA (RGBHV, or YPbPr), or CV and
line level stereo audio
Resolution
Bandwidth
Up to 1600 x 1200 at up to 85 Hz PC or 1080i HDTV
DC to 250 MHz
Max. Distance Up to 328 ft. (100 m) with Phantom Power, or 500 ft
(150 m) with additional power supply at receiver for
VGA or 1200 feet for CV and audio
Connectors
Interfaces
HD15 female for video in and out; Shielded RJ45
Standard Analog VGA; Proprietary CAT5
Compliance CE; FCC Part 15 Subpart B Class A, IC Class
Max. Altitude 10,000 ft. (3048 m)
Temperature Operating: 32 to 122°F (0 to 50°C);
Storage: –40 to +185°F (–40 to +85°C)
Humidity
Enclosure
MTBF
Up to 95% non-condensing
Aluminum and Steel
100,000 hours (calculated estimate)
Power
From utility-power (mains) outlet, through included
Universal power adapter. Input Voltage: 100~240
VAC Output Voltage: 9v DC regulated Center-Positive
at 1.7A Max
Dimensions
Weight
1.1" H X 2.75" W X 3.1" L
1.6 lbs
8
Mini Cat5 VGA Transmitter w/ Local Port
5. Appendix
EIA/TIA 568B WIRING STANDARD
PIN
Wire Color
1
2
3
4
5
6
7
8
White w/ Orange Stripe
Orange
White w/Green Stripe
Blue
White w/Blue Stripe
Green
White w/Brown Stripe
Brown
9
Model AC603A
10
Mini Cat5 VGA Transmitter w/ Local Port
11
© Copyright 2007. Black Box Corporation. All rights reserved.
1000 Park Drive Lawrence, PA 15055-1018 724-746-5500
Fax 724-746-0746
|