The setup guide
If at any time during this warranty period the
equipment proves to be defective for any reason
other than accident, misuse, neglect, unauthorised
modification or fair wear and tear, we will repair
any such manufacturing defect or, at our option,
replace it without charge for labour, parts or
return carriage.
.14. Warning: To reduce the risk of fire or electric
shock, this apparatus should not be exposed to
rain or moisture and objects filled with liquids,
such as vases, should not be placed on
the apparatus.
If you suspect a problem with a Tannoy product
then, in the first instance, discuss it with your
Tannoy dealer. If you require further assistance
then we ask that you deal directly with your local
Tannoy distributor. If you cannot locate your
distributor please contact Customer Services,
Tannoy Ltd at the address given below.
15. To completely isolate this apparatus from the
mains, disconnect the power supply plug from
the receptacle.
16. The mains plug of the power supply cable shall
remain readily operable.
Customer Services, Tannoy Ltd., Rosehall
Industrial Estate, Coatbridge, Strathclyde
ML5 4TF, Scotland
17. Store complete packaging in case it is needed
for re-use.
Tel:
01236 420199
+44 1236 420199
01236 428230
(National)
(International)
(National)
18. Due to the powerful drive unit magnet, do not
place within 1m (3 feet) of a television or
computer monitor.
Fax:
+44 1236 428230
(International)
E-mail:
Warranty
Do not ship any product to Tannoy without
previous authorisation.
All of our products have been produced and tested
with care and precision to give first-class service.
Our policy commits us to incorporating
improvements to our products through continuous
research and development. Please confirm current
specifications for critical applications with
your supplier.
All passive components are guaranteed for a
period of five years from the date of purchase from
an authorised Tannoy dealer subject to the
absence or evidence of misuse, overload, or
accidental damage.
All active and electronic components are
guaranteed for a period of one year from the date
of purchase from an authorised Tannoy dealer
subject to the absence of, or evidence of, misuse,
overload or accidental damage.
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage " within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
Warning: Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage.
Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, liquids, moisture,
excessive heat, or naked flame.
5.1 system setup guide
This high performance 5.1 system has been built
and tested with care and precision, to provide first class
performance and reliable operation. To ensure
maximum benefit from ownership, and for reasons of
safety, please read the following information before
using for the first time.
AV RECEIVER/DECODER OUTPUT PANEL
SUB OUT
FRONT
REAR
CENTRE
REAR
FRONT
LEFT
LEFT
RIGHT
RIGHT
_
_
_
_
_
+
+
+
+
+
_
Connecting the subwoofer
to your system
The SFX5.1 system subwoofer may be connected in
any one of the following ways:
Line levels
•
•
•
Using the subwoofer output on your A/V receiver or
decoder connect a single RCA interconnect to either
the left or right line input on the subwoofer rear
panel. This is the ideal connection type as the sub
woofer output contains the low frequency
information from all channels.
High levels
If no subwoofer or spare line outputs exist you may
connect using a Y-split connector on the main pre
amplifier output connections. Use a Y-split on both
right and left outputs and connect these via an RCA
interconnect to the left and right inputs on the
subwoofer rear panel.
Alternatively, if your preamplifier has a spare set of
line level outputs, connect left and right to the SFX
subwoofer L and R inputs using screened cable.
•
Use your amplifier's speaker out terminals.
To accommodate the connection of two sets of
cables, red (+) goes to red (+), and black (-) to
black (-), twist wires together and connect to the
amplifier terminals.
•
Alternatively use the 'A & B' speaker outputs on the
amplifier if provided - A to your main speakers and B
to the SFX subwoofer. Do this using a length of
speaker cable for each channel, wire your amplifier
outputs to the HIGH LEVEL input terminals, on the
subwoofer amplifier panel. Ensure there are no
stray wire strands that could possibly short together
and damage both the amplifier and subwoofer.
Warnings
•
Double-check all connections before switching on
the SFX system and your amplifier.
•
Ensure that the polarity of the speaker cables from
your amplifier to the subwoofer is correct - failure to
observe this will result in damage to your amplifier.
When using the HIGH LEVEL inputs, ensure
that your amplifier is not configured in bridge mode;
damage could result to either the amplifier or the
subwoofer. If in doubt consult your dealer.
•
Setting up
Ensure the POWER switch is in the OFF position. You
can operate the SFX subwoofer in two modes, AUTO
and ON. Set to AUTO, the unit remains switched off until
a signal is present (power saving), set to ON the unit
runs continuously. Connect the SFX subwoofer to a con-
venient mains socket using the lead and plug supplied.
Positioning
As the SFX subwoofer produces low frequencies only,
it is difficult to detect its location by ear. It can therefore
be placed anywhere in the room, but optimum perform-
ance will be gained by locating the subwoofer between
the front pair of speakers. Bass output will increase
next to a wall or especially in a corner; so use the
volume control to compensate if moving your sub-
woofer around.
Set the SFX subwoofer VOLUME to MIN, PHASE
SWITCH to 0°, CROSSOVER to AV/LFE. Set your 5.1
or 6.1 receiver/decoder to SMALL SPEAKERS, LFE or
SUB output to ON and play a favourite disc. Switch the
SFX subwoofer to ON and set the VOLUME to AV/LFE.
Assess the bass signal strength and adjust VOLUME
accordingly. The purpose of a subwoofer is to enhance
the bass or low frequencies but not to overpower the
music or film dialogue. Set up can be checked by using
the noise signal calibration facility in most 5.1 or 6.1
receivers/decoders.
Auto power/Sleep functions
The SFX subwoofer can be left permanently on in
AUTO mode, under which conditions it will revert to
'sleep' mode after approximately 20 minutes. If not
using your subwoofer for some time, switch off and
remove the power cable from the mains outlet.
Power requirements
Check that the voltage rating displayed on the rear
panel is correct for your area before connecting. If it is
incorrect, move the voltage selector on the rear panel
to the appropriate voltage. The panel mounted fuse
should also be changed to the correct rating (see
below, under FUSE PROTECTION). If in any doubt,
consult your Dealer or Authorised Service Agent.
Centre & Satellites
PERFORMANCE
Recommended amplifier power
Maximum Sensitivity (2.83Volts @ 1m)
Nominal impedance
15 - 100 Watts
85dB
6 Ohms
Frequency response (-6dB)
Drivers
140Hz - 78kHz
HF: 15mm (0.59”) titanium dome, neodymium magnet system
LF: 75mm (2.95”) paper cone
4.5kHz (mid to high) 140Hz (to subwoofer)
Yes
Crossover frequency
Magnetic shielding
Satellite Weight
750gms (1.65lbs)
Satellite Dimensions H x W x D
Centre Weight
140 x 97 x 95mm (5.51 x 3.82 x 3.74”)
1.5kg (3.3lbs)
Centre Dimensions H x W x D
Finish
120 x 230 x 95mm (4.72 x 9.06 x 3.74”)
Black
White
Supplied accessories
Optional accessories
Wall mounting brackets
25 metres (82ft 6”) speaker cable
Satellite floor stands available in black
Subwoofer
PERFORMANCE
Power output
100 Watts
Frequency response (-6dB)
Driver
Inputs
Power requirements
Fuse ratings
45Hz - 140Hz
200mm (8.00”) paper cone
Twin line or speaker level
160VA max
AC100-120V / 60Hz - Fuse: T1.6A L /250V
AC 220-240V / 50Hz - Fuse: T800mA L /250V
ON / OFF/ AUTO power function
9.0kg (20.0lbs)
Additional features
Weight
Dimensions H x W x D
Finish
345 x 250 x 370 mm (13.58 x 9.84 x 14.57”)
Black
White
How it all adds up
TC Group International T: 00 45 8742 7000
TC Group Americas
Tannoy Middle East
T: 00 1 (519) 745 1158
T: 00 971 (04) 4401208
tannoy.com
Tannoy adopts a policy of continuous improvement and product specification is subject to change.
|