SunSwift™ SBusAdapter
Installation andUser’sGuide
The Network Is the Computer™
Sun Microsystems Computer Company
2550 Garcia Avenue
Mountain View, CA 94043 USA
415 960-1300
fax 415 969-9131
Part No.: 802-4535-10
Revision A, December 1995
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
1. Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 If Solaris 2.5 is Not Installed on Your System . . . . . . . . . . 1-3
1.3 If Solaris 2.5 is Installed on Your System . . . . . . . . . . . . . . 1-3
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2. Installing the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Performing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Verifying the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 Booting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4 Installing the Solaris 2.5 Software . . . . . . . . . . . . . . . . . . . 2-4
2.5 Post-Installation Procedures (Optional) . . . . . . . . . . . . . . 2-5
2.5.1 Watching Network Activity . . . . . . . . . . . . . . . . . . . . 2-5
iii
2.5.2 Running Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.5.3 Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.5.4 Configuring Driver Parameters. . . . . . . . . . . . . . . . . 2-6
A. Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
B. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
iv
SunSwift SBus Adapter Installation and User’s Guide—December 1995
Preface
This manual describes how to install and use your SBus card.
The procedures in this manual assume that you are a system or network
administrator experienced in installing similar hardware and that you are
familiar with Solaris administration.
UNIX Commands
This document may not include specific software commands or procedures.
Instead, it may name software tasks and refer you to operating system
documentation or the handbook that was shipped with your new hardware.
The type of information that you might need to use references for includes:
• Shutting down the system
• Booting the system
• Configuring devices
• Other basic software procedures
See one or more of the following:
• Solaris 2.x Handbook for SMCC Peripherals contains Solaris™ 2.x software
commands.
• On-line AnswerBook™ for the complete set of documentation supporting
the Solaris 2.x software environment.
• Other software documentation that you received with your system.
v
Typographic Conventions
The following table describes the typographic changes used in this book.
Typeface or
Symbol
Meaning
Example
AaBbCc123
The names of commands,
files, and directories;
on-screen computer output
Edit your.loginfile.
Use ls -ato list all files.
machine_name% You have mail.
AaBbCc123
AaBbCc123
AaBbCc123
What you type, contrasted
with on-screen computer
output
machine_name% su
Password:
Command-line placeholder:
replace with a real name or
value
To delete a file, type rmfilename.
Book titles, new words or
terms, or words to be
emphasized
Read Chapter 6 in the User’s Guide.
These are called class options.
You must be root to do this.
Shell Prompts
The following table shows the default system prompt and superuser prompt
for the C shell, Bourne shell, and Korn shell.
Shell
Prompt
C shell
machine_name%
machine_name#
C shell superuser
Bourne shell and Korn shell $
Bourne shell and Korn shell #
superuser
vi
SunSwift SBus Adapter Installation and User’s Guide—December 1995
Related Documents
The following documents contain topics that relate to the information
in the SunSwift SBus Adapter Installation and User’s Guide.
Title
Part Number
Your system installation or service manual
Solaris 2.5 Handbook for SMCC Peripherals
SMCC Open Issues Supplement Solaris 2.5
Solaris 2.5 on Sun Hardware AnswerBook
SunVTS 1.0 User’s Guide
802-3725
802-3708
801-7271
Platform Notes: The hme Fast Ethernet Device Driver 802-3970
Ordering Sun Documents
The SunDocs Order Desk is a distribution center for Sun Microsystems
technical documents. You can use major credit cards and company purchase
orders. You can order documents in the following ways.
In the U.S.A.
Outside the U.S.A.
Fax 1-801-373-6798
Call 1-801-342-3450
Fax 1-801-373-6798
Call 1-800-247-0250
Sun Welcomes Your Comments
Please use the Reader Comment Card that accompanies this document. We are
interested in improving our documentation and welcome your comments and
suggestions.
If a card is not available, you can email or fax your comments to us. Please
include the part number of your document in the subject line of your email or
fax message.
• Fax:
SMCC Document Feedback
1-415-786-6443
Preface
vii
!
FCC Class B Notice—United States
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Note - This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed an used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a power outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ television technician for help.
Shielded Cables
Connections between the workstation and peripherals must be made using shielded cables in order to maintain compliance
with FCC radio frequency emission limits.
Modifications
Modifications to this device, not approved by Sun Microsystems, Inc. may void the authority granted to the end user by the
FCC to operate the equipment.
DOC Class B Notice—Canada
This digital apparatus does not exceed Class B limits for radio noise emission for a digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Avis Concernant les Systèmes Appartenant à la Classe B du DOC—Canada
Le présent appareil numérique n´émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
viii
SunSwift SBus Adapter Installation and User’s Guide—December 1995
x
SunSwift SBus Adapter Installation and User’s Guide—December 1995
Preparingfor Installation
1
The SunSwift™ SBus Adapter offers fast Ethernet and FastWide SCSI-2
capabilities on the same SBus card.
SBus
connector
SCSI-2
connector
Ethernet
connector
This SBus card offers the following features:
• Switchable 10BASE-T/ 100BASE-TX Ethernet. Automatically sets
10/ 100 Mbps speed. Conforms to IEEE 802.3u Ethernet standard.
• 20 Mbytes/ s, 16-bit, single-ended SCSI-2 controller. Conforms to ANSI
X3T9.2 SCSI-2 standard.
• SBus interface to host system. Complies with IEEE 1496 SBus specification.
1-1
1
1.1 Requirements for Using the SBus Adapter
Before installing the adapter, make sure your system meets the following
hardware and software requirements:
Systems
Sun™ Ultra™ 140, Sun Ultra Creator 170E,
SPARCstation™ 4, SPARCstation 5, SPARCstation 10
models, SPARCstation 20 models, SPARCserver™
600MP series, SPARCserver 1000 or SPARCcenter™ 2000
Firmware
OpenBoot™ PROM Version 2.9 or greater
Solaris™ 2.5 environment
Operating System
Peripherals
Only Sun SCSI-2 devices
SCSI Cables
Only standard, Sun-supported cabling to ensure reliable
SCSI interface connections
Part Numbers
530-2115-02 (1.2 m 50-pin to 68-pin cable)
530-1884-03 (0.8 m 68-pin to 68-pin cable)
530-2228-01 (2 m 50-pin to 68-pin cable)
530-1885-03 (2 m 68-pin to 68-pin cable)
SCSI Cabling
You can daisy chain up to 15 devices on the SunSwift SBus Adapter as follows:
Wide-to-wide devices
Use a 68-pin to 68-pin cable.
Always put wide SCSI devices closest to the host system.
Use a 68-pin to 50-pin cable.
Wide-to-narrow devices
You can include only one wide-to-narrow cable along a
chain of peripherals.
Always put the narrow SCSI devices at the end of the
chain.
The SCSI bus must be terminated at the end of the chain.
Note – If you use the SunSwift SBus Adapter for SCSI purposes only, you must
change the device name from SUNW,hmeto SUNW,hme_idleto avoid a “Link
Down — cable problem?” message. Refer to SMCC Open Issues Supplement
Solaris 2.5 for more detailed information.
1-2
SunSwift SBus Adapter Installation and User’s Guide—December 1995
1
Ethernet Cabling
An additional Ethernet cable is required if you want to use your system’s
existing Ethernet interface and the SunSwift SBus Adapter Ethernet interface.
Disabling Your Current Ethernet Device
If you remove your system’s existing Ethernet cable (either from its on-board
Ethernet device or from an existing Ethernet card) and insert it into the
SunSwift SBus Adapter Ethernet connection, you must disable your current
card’s Ethernet device. For example, if your current Ethernet device is called
le0, you would remove its IP address and host name from the /etc/hosts
file and remove the /etc/hostname.le0file itself.
1.2 If Solaris 2.5 is Not Installed on Your System
1. Install the SunSwift SBus Adapter as described in Chapter 2 first.
2. Install the Solaris 2.5 software environment after the adapter installation,
as described in Section 2.4, “Installing the Solaris 2.5 Software.”
1.3 If Solaris 2.5 is Installed on Your System
If the Solaris 2.5 software is already installed on your system, you must
perform the following installation tasks before installing the SunSwift SBus
Adapter.
• If you are using the SunSwift SBus Adapter as your only Ethernet interface,
perform the tasks in section 1.3.1.
• If you are using the SunSwift SBus Adapter and another Ethernet interface,
perform the tasks in section 1.3.2.
Preparing for Installation
1-3
1
1.3.1 Using the SunSwift SBus Adapter as Your Only Ethernet Interface
You will be installing software from the Solaris 2.5 CD-ROM. Make sure the
Solaris 2.5 CD-ROM is properly placed in the CD-ROM drive before
performing the following tasks.
1. As superuser, add the SUNWhmdand SUNWhmdupackages to your system:
# pkgadd -a none -d /cdrom/solaris_2_5_sparc/s0/Solaris_2.5 SUNWhmd SUNWhmdu
2. For both packages, answer /to the following question:
Enter path to package directory [?,q]
You will receive a message stating the process was successful.
3. Assign an IP address and host name for the SunSwift SBus Adapter
Ethernet channel.
For example, 123.456.78.90(IP address); zardoz(host name).
4. Edit the /etc/hostsfile and remove your existing Ethernet interface’s
IP address and host name.
5. Add an entry to the /etc/hostsfile containing the new IP address and
host name for the selected hmechannel.
This is the IP address and host name that you assigned in step 3.
6. Remove your existing Ethernet interface’s /etc/hostname.xx<num>file
from your system.
7. Create a /etc/hostname.hme<num>file for the Ethernet channel you are
planning to use for the SunSwift SBus Adapter.
• hostnameis literal. Type hostname.
• numis the instance number of the SBus card installation. Use 0for the first
SunSwift SBus Adapter installation, 1for the second instance, and so on.
8. In this file, add a line containing just the host name that you assigned for
the SunSwift SBus Adapter. For example, if your host name is zardoz,
enter just this word.
1-4
SunSwift SBus Adapter Installation and User’s Guide—December 1995
1
9. Power off your system, using standard shutdown procedures described in
Solaris 2.5 Handbook for SMCC Peripherals.
10. Install the SunSwift SBus Adapter as described in Chapter 2.
1.3.2 Using the SunSwift SBus Adapter and Existing Ethernet Interface
You will be installing software from the Solaris 2.5 CD-ROM. Make sure the
Solaris 2.5 CD-ROM is properly placed in the CD-ROM drive before
performing the following tasks.
If you want to use the SunSwift SBus Adapter Ethernet interface and your
existing Ethernet interface, you must perform the following tasks before
installing the SunSwift SBus Adapter.
Note – Make sure you have an Ethernet cable for each Ethernet interface.
1. As superuser, add the SUNWhmdand SUNWhmdupackages to your system:
# pkgadd -a none -d /cdrom/solaris_2_5_sparc/s0/Solaris_2.5 SUNWhmd SUNWhmdu
2. For both packages, answer /to the following question:
Enter path to package directory [?,q]
You will receive a message stating the process was successful.
3. Assign an IP address and host name for the SunSwift SBus Adapter
Ethernet channel.
For example, 123.456.78.90(IP address); zardoz(host name).
4. Edit the /etc/hostsfile and add an entry containing the new IP address
and host name for the selected hmechannel.
This is the IP address and host name that you assigned in step 3.
Preparing for Installation
1-5
1
5. Create a /etc/hostname.hme<num>file for the Ethernet channel you are
planning to use for the SunSwift SBus Adapter.
• hostnameis literal. Type hostname.
• numis the instance number of the SBus card installation. Use 0for the first
SunSwift SBus Adapter installation, 1for the second instance, and so on.
6. In this file, add a line containing just the host name that you assigned for
the SunSwift SBus Adapter. For example, if your host name is zardoz,
enter just this word.
7. Power off your system, using standard shutdown procedures described in
Solaris 2.5 Handbook for SMCC Peripherals.
8. Install the SunSwift SBus Adapter as described in Chapter 2.
1-6
SunSwift SBus Adapter Installation and User’s Guide—December 1995
InstallingtheAdapter
2
This chapter tells you how to install the adapter in your system, verify that the
adapter is correctly installed, and boot your system.
2.1 Performing the Installation
Note – Refer to your system installation or service manual (and the SCSI
device installation manual, as necessary) for detailed instructions for the
following tasks.
1. Power off your system, using the standard shutdown procedures
described in Solaris 2.5 Handbook for SMCC Peripherals.
2. If you are replacing an SBus card with the SunSwift SBus Adapter,
remove the old card now.
3. Install the SunSwift SBus Adapter in the selected SBus slot.
4. Attach the SCSI cable to the 68-pin SCSI connector on the adapter and to
the SCSI device, if necessary.
5. Connect the Ethernet cable to the SunSwift SBus Adapter RJ-45 connector
and to the hub.
Connect the new Ethernet cable if you are using two Ethernet interfaces.
2-1
2
2.2 Verifying the Installation
Refer to the Solaris 2.5 Handbook for SMCC Peripherals manual or your Solaris
documentation for detailed instructions for the following tasks.
1. Power on the system, and when the banner appears, press the Stop-A keys
to interrupt the boot process and get to the okprompt.
2. Use the show-devscommand to list the devices in the system.
You should see two lines (similar to the example below) in the display,
specific to the SunSwift SBus Adapter:
ok show-devs
...
/iommu@f,e0000000/sbus@f,e0001000/SUNW,fas@0,8800000
/iommu@f,e0000000/sbus@f,e0001000/SUNW,hme@0,8c00000
...
• fas@0identifies the adapter’s SCSI-2 device.
• hme@0identifies the adapter’s Ethernet device.
Note – In the above example, the number 0following fas@and hme@
corresponds to the instance number of the SunSwift SBus Adapter installation.
The numbers you see when listing the system devices may be different.
If you do not see these devices listed, check that the adapter is properly seated
and reinstall the adapter, if necessary.
2-2
SunSwift SBus Adapter Installation and User’s Guide—December 1995
2
2.3 Booting the System
Refer to the Solaris 2.5 Handbook for SMCC Peripherals manual for detailed
instructions for the following tasks.
• To boot the system from the default boot device, use the boot-rcommand.
• To use the SunSwift SBus Adapter Ethernet interface as the boot device,
specify the OpenBoot™ device name with the boot command, for example:
ok boot -r /iommu@f,e0000000/sbus@f,e0001000/SUNW,hme@0,8c00000
Note – A “SUNW,hme0:LinkDown - cable problem?” message means that the
Ethernet cable is disconnected either at the RJ-45 connector or at the hub.
Installing the Adapter
2-3
2
2.4 Installing the Solaris 2.5 Software
You will be installing software from the Solaris 2.5 CD-ROM. Make sure the
Solaris 2.5 CD-ROM is properly placed in the CD-ROM drive before
performing the following tasks.
♦ Install the Solaris 2.5 software.
Installing the software will automatically add the SUNWhmdand SUNWhmdu
packages.
The installation process will also create the necessary
/etc/hostname.hme<num> file and the hmechannel entries in the
/etc/hostsfile, only if you select hme<num> as the primary interface when
prompted during the installation.
If you are going to use more than one Ethernet interface, you must manually
re-enter your existing Ethernet interface’s device name in the /etc/hostsfile
and create its hostname.xx<num> file. Perform the following tasks after
installing the Solaris 2.5 software.
1. As superuser, edit the /etc/hostsfile and add an entry for the existing
Ethernet device, for example, le0.
2. Create a /etc/hostname.xx<num> file for the Ethernet channel you are
planning to use for the existing Ethernet device.
• hostnameis literal. Type hostname.
• numis the instance number of the SBus card installation. Use 0for the first
SBus card installation, 1for the second instance, and so on.
3. In this file, add a line containing just the host name for the existing
Ethernet interface. For example, if your host name is zardoz, enter just
this word.
2-4
SunSwift SBus Adapter Installation and User’s Guide—December 1995
2
2.5 Post-Installation Procedures (Optional)
Perform the following tasks to verify and customize the performance of the
SunSwift SBus Adapter.
2.5.1 Watching Network Activity
Make sure that you are connected to an active network.
♦ You can watch network activity or incoming network packets by typing
the following:
ok watch-net-all
/iommu@f,e0000000/sbus@f,e0001000/SUNW,hme@0,8c00000
hme register test -- succeeded.
Internal loopback test -- succeeded.
Transceiver check -- Using Onboard Transceiver, 100 Mbps Link
Down, 10 Mbps Link Up, passed
Using Onboard Transceiver, 100 Mbps Link Down, 10 Mbps Link Up,
Looking for Ethernet packets.
'.' is a good packet. 'X' is a bad packet.
Type any key to stop.
...........
Note – The network speed is the same as the speed of the hub to which your
system is connected. See Section 2.5.3 “Auto-Negotiation” and Section 2.5.4
“Configuring Driver Parameters” for information on speed selection.
2.5.2 Running Diagnostics
Refer to the SunVTS 1.0 User’s Guide document for diagnostic tests for the
SunSwift SBus Adapter.
Installing the Adapter
2-5
2
2.5.3 Auto-Negotiation
A key feature of the SunSwift SBus Adapter is auto-negotiation. The auto-
negotiation protocol, as specified by the 100BASE-TX standard, automatically
selects the operation mode (half-duplex or full-duplex) and speed (10 Mbps or
100 Mbps) for the adapter.
The hmedevice driver operates the SUNW,hmedevice by default in half-
duplex mode only.
If the SunSwift SBus Adapter is connected to a remote system or interface that
is not capable of auto-negotiation, your system automatically selects the speed
and half-duplex mode.
If the SunSwift SBus Adapter is connected to a link partner with which the
auto-negotiation protocol fails to operate successfully, you can configure the
device to not use this protocol and force the driver to set up the link in the
mode and speed of your choice.
Refer to the Platform Notes: The hme Fast Ethernet Device Driver document (Part
No: 802-3970) for more information on the hmedevice driver and auto-
negotiation. (This document is also available on the Solaris 2.5 and the Solaris
2.5: 1/ 96 AnswerBook.)
2.5.4 Configuring Driver Parameters
The hmedevice driver, which is loaded from the Solaris 2.5 CD-ROM, controls
the SUNW,hmeEthernet device. The device driver automatically selects the link
speed using the auto-negotiation protocol with the link partner.
You can manually configure the hmedevice driver parameters to customize
each SUNW,hmedevice in your system in one of three ways:
• Configure the hmedriver parameters generally for all devices in the system
by entering the parameter variables in the /etc/systemfile.
• Set a parameter on a per-device basis by creating the hme.conffile in the
/kernel/drvdirectory.
• Use the nddutility to temporarily change a parameter. This change is lost
when you reboot the system.
2-6
SunSwift SBus Adapter Installation and User’s Guide—December 1995
InterfaceSignals
A
A.1 SunSwift SBus Adapter Connectors
1
1
34
68
8
35
68-pin SCSI-2 Connector
RJ-45 Connector
A.2 RJ-45 Connector Signals
Pin
Signal
1
2
3
4
5
6
7
8
Transmit+
Transmit-
Receive+
No Connection
No Connection
Receive-
No Connection
No Connection
A-1
A
A.3 SCSI-2 Connector Signals
Pin
1
2
3
4
5
6
7
8
Signal
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Signal
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_TERMPOWER
SCSI_TERMPOWER
PULLUP
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_GND
SCSI_D<12>_
SCSI_D<13>_
SCSI_D<14>_
SCSI_D<15>_
SCSI_DATA_PARITY1_
SCSI_D<0>_
SCSI_D<1>_
SCSI_D<2>_
SCSI_D<3>_
SCSI_D<4>_
SCSI_D<5>_
SCSI_D<6>_
SSCSI_D<7>_
SCSI_DATA_PARITY0_
SCSI_GND
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
SCSI_GND
SCSI_TERMPOWER
SCSI_TERMPOWER
PULLUP
SCSI_GND
SCSI_ATN_
SCSI_GND
SCSI_BSY_
SCSI_ACK_
SCSI_RST_
SCSI_MSG_
SCSI_SEL_
SCSI_CD_
SCSI_REQ_
SCSI_IO_
SCSI_D<8>_
SCSI_D<9>_
SCSI_D<10>_
SCSI_D<11>_
A-2
SunSwift SBus Adapter Installation and User’s Guide—December 1995
Specifications
B
B.1 Physical Characteristics
Length
Width
Weight
5.78 in. (147.70 mm)
3.3 in. (83.82 mm)
4.0 oz. (113.40 g)
B.2 Power Requirements
Maximum Power Dissipation 9.5 Watt
Voltage Tolerance
Ripple
Operational Current
5V +/ - 5%
Maximum 100 mV
1.9A
B.3 Performance Specifications
Maximum Ethernet Transfer Rate 10/ 100 Mbps
Network Interface
100BASE-TX using Category 5 (data-grade) cable;
10BASE-T using Category 3 (voice-grade) cable or
better
Ethernet Version
SCSI Interface
SBus Clock
Conforms to IEEE 802.3u
20 Mbytes/ s, 16-bit single-ended
16.67 MHz to 25 MHz
SBus Burst Sizes
SBus Modes
SBus Parity
16/ 32/ 64 bytes
Master/ Slave, 64-bit support
Yes
SBus Version
Conforms to IEEE 1496
B-1
B
B-2
SunSwift SBus Adapter Installation and User’s Guide—December 1995
Reader Comments
We welcome your comments and suggestions to help improve this manual. Please let us
know what you think about the SunSwift SBus Adapter Installation and User’s Guide,
part number 802-4535-10.
■
■
■
■
■
The procedures were well documented.
Strongly
Agree
Strongly
Disagree
Not
Applicable
Agree
Disagree
❑
❑
❑
❑
❑
Comments
The tasks were easy to follow.
Strongly
Strongly
Disagree
Not
Applicable
Agree
Agree
Disagree
❑
❑
❑
❑
❑
Comments
The illustrations were clear.
Strongly
Strongly
Disagree
Not
Applicable
Agree
Agree
Disagree
❑
❑
❑
❑
❑
Comments
The information was complete and easy to find.
Strongly
Strongly
Disagree
Not
Applicable
Agree
Agree
Disagree
❑
❑
❑
❑
❑
Comments
Do you have additional comments about the SunSwift SBus Adapter Installation and
User’s Guide?
Name:
Title:
Company:
Address:
Telephone:
Email address:
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST CLASS MAIL PERMIT NO. 1 MOUNTAIN VIEW, CA
POSTAGE WILL BE PAID BY ADDRESSEE
SUN MICROSYSTEMS, INC.
Attn: Manager, Hardware Publications
MS MPK 14-101
2550 Garcia Avenue
Mt. View, CA 94043-9850
|
