FULL MANUAL
OPERATING INSTRUCTIONS
DIRECT DRIVE TURNTABLE
T.8O
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
21. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
CAUTION: To reduce the risk of electric shock, do not
CAUTION
remove any cover. No user-serviceable parts inside. Refer
servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
CAUTION
To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.
ŸThis device complies with Part 15 of the FCC Rules Operation is Subject to the following two conditions (1) This
device may not Cause harmful interference, and (2) this device must accept any Interference received. Including
interference that may cause Undesired operation.
ŸThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
ŸUnauthorized modification of this unit may cause it to no longer comply with FCC regulations and void your
authority to use this device.
ŸCet appareil numérique de la classe B respecte toutes les exigencies du Rèsur le materiel brouilleur du Canada.
ASSEMBLY
Remove all the parts from the box. Please check to make sure the following items are included with the main unit in
the carton:
(1) Platter
(2) Slip mat
(3) Counterweight
(4) 45-rpm adapter
(5) 500B Cartridge and Headshell
(6) AC cord
(7) RCA cable
(8) Target light
(9) Operating instructions
(10) Cloth dust cover
CONNECTIONS
1) Connect the power cord to an AC outlet.
2) Connect the RCA cable to the PHONO input of your mixer. You can also use a line input by setting the phono/line
switch at the rear of the turntable to Line.
Note: This turntable has separate analog and digital circuits. If you are looking for a purely analog signal, use the
Phono output. For access to the Key Lock feature use the Line output or S/P DIF output.
TONE ARM AND CARTRIDGE SETTINGS
The major cause of problems in sound and skipping on the vinyl is the lack of proper set up of the needle and
turntable adjustments. The needle is designed to operate at a specific angle to the vinyl. The T.80 has several
adjustments to correctly position the needle to the vinyl.
The first adjustment is the correct installation of the cartridge.
Your cartridge is to be mounted into the headshell as pre the mounting instructions included with the cartridge. The
Stanton 500,680 and 890 series of cartridges require the use of the two screws mounting into the headshell. For your
convenience, some of these products can be purchased already mounted and pre-adjusted from your local Stanton
dealer. If you are using these 1/2” mounted products with a headshell in a mobile application or you are doing heavy
scratching, May want to use an extra shell weight. The Master series of products (Trackmaster, Groovemaster, etc.)
are designed with their own mounting that eliminates the need for a separate headshell and the wiring to the
cartridge.
The body of the cartridge should be parallel with the centerline of the headshell-tone arm, when viewed from the
front to the back.
The second adjustment is at the installation of the cartridge-head-shell assembly into the tone arm tube lock.
Holding the tone arm tube in one hand, insert the cartridge-headshell into the tube lock with the other hand. Turn
the lock ring clockwise (when viewed from the rear) until the headshell is locked tightly into the tone arm. Remove
the needle protector from the cartridge and place the needle on record. View the needle from the front and insure
that the needle is perpendicular to the record surface. If some adjustment is needed, simply loosen the lock ring and
rotate the cartridge-headshell until the needle is perpendicular to the record surface. Then re-tighten the lock ring.
The third adjustment is the needle (or stylus) pressure. Start with the cartridge-headshell assembly mounted into
the tone arm. Remove any needle protectors provided. With tone arm free, adjust the tone arm counterweight by
rotating the rear section until the tone arm floats in a balanced condition above the record or mat. Do not allow the
needle to drop onto the mat or the turntable platter during this adjustment. You might damage the needle tip. Now,
carefully hold the tone arm in one hand while rotating the numbered ring on the front of the counter-weight with the
other hand to the “0” setting. Next, without touching the numbered ring, Rotate the rear counterweight until the
desired needle pressure reading is next to the line on top of the tone arm tube, see the instructions. Included with
your cartridge for proper settings.
PART NAMES & FUNCTIONS
18 17
1
2
16
15
3
4
5
14
13
12
11
6
2
10
7
8
9
1) REVERSE
This button is used to reverse the direction of the platter rotation.
2) START/STOP
Press this button to start or stop the platter.
3) STROBE DOTS
The dots around the edge of the platter are used in conjunction with the light located inside the motor ON/OFF
switch. While the platter is in rotation, the dots help to indicate the speed of rotation. The speed is lower than the
displayed speed (33,45,78) when the dots are flowing to the right. It is higher than the displayed speed (33,45,78)
when the dots are flowing to the left. When the strobe is stopped, the platter is rotating at the displayed speed.
4) SLIP MAT
5) CENTER SPINDLE
6) MOTOR ON/OFF SWITCH
As opposed to fully analog turntables, this is not the power switch. This switch only turns on or off the motor.
Rotate clockwise to turn on the motor. The platter will not start spinning until the start/stop button has been
pressed. Rotate counter-clockwise during playback (off position) for a slow winding down effect.
7) PLATTER REVOLUTION SPEEDS (rpm)
33 rpm – Press 33
45 rpm – Press 45
78 rpm – Press 33 and 45 buttons simultaneously.
To return to 33 or 45-rpm play mode, just press the desired button.
PART NAMES & FUNCTIONS
8) TARGET LIGHT BASE
Insert target light to the deck and it will light up.
9) KEY LOCK
Press to enable Key Lock. When Key Lock is on, the pitch slider will only affect the speed of the platter. The key
(tone) will remain at 0%.
Note: Key Lock processing is only available when the LINE output is used.
10) PITCH LOCK
The ON setting will allow use of the pitch adjust. When set of OFF, the pitch control will be locked at 0%.
11) PITCH SLIDER
The pitch slider is used to speed up or slow down the turntable platter.
12) HEADSHELL LOCKING NUT
Attach the headshell by inserting into the front end of the tone arm. Turn the locking nut clockwise with the head
shell firmly held horizontally.
13) TONE ARM
This is a fully manual tone arm. To start playback, gently place the stylus on the record using the headshell finger
support. Do not drop the stylus onto the record as it may cause damage to the diamond tip and to the record.
14) PITCH SELECT
Press the button to select between +/-8% and +/-12% pitch range.
15) TONE ARM BASE
The tone arm base includes tone arm rest.
16) COUNTERWEIGHT
Use this to balance the tone arm and to adjust the stylus pressure. See “tone arm and cartridge settings” for
proper adjustments.
17) 45-RPM ADAPTOR HOLDER
Place on the attached 45-rpm adaptor here. Push down the rear side of 45 rpm adaptor to take it.
18) EXTRA STYLUS HOLDER
Place extra headshells here.
19 20 21
22 23
19) PHONO/LINE OUTPUT L & R
This is the standard analog output (RCA jacks) which can be connected either to a phono or line input on any DJ
mixer, depending on the setting of the phono / line selector.
Note: Key Lock processing is only available when the LINE output is used.
PART NAMES & FUNCTIONS
20) PHONO/LINE SWITCH
Note: Key Lock and Digital output processing is only available when the LINE output is used.
21) DIGITAL OUT
Use this output to connect your T.80 to any SPDIF in equipped digital device.
22) POWER CORD CONNECTOR
Used to connect the included power cord.
23) POWER SWITCH
This switch turns the power on or off, including the motor and audio signal.
SPECIFICATIONS
APPLICATION:
This specification applies to the direct drive turntable unit T.80
STANDARD TEST CONDITION:
Ambient Temperature
Relative Humidity
20 +/- 2 degC
65% +/- 5%
NOTE: Measurements can be carried out between 5 degC to 35 degC and 45% to 85% relative humidity.
TURNTABLE SECTION:
Type
3-speed full manual
Motor
Speeds
8pole, 3phase,brushless DC motor
33 /3 and 45rpm and 78rpm
1
1
Wow and Flutter
Pitch Controls
Starting Torque
Starting Time
Braking Time
Braking System
Time for Speed Change
Less than 0.15% WRMS (JIS WTD) with 33 /3rpm
+/- 8%, +/-12%
More than 1.6kgf.cm
Less than 1 sec. with 33 /3 rpm
Less than 1 sec. with 33 /3 rpm
1
1
Electronic brake
Less than 1 sec. from 33 /3 to 45 rpm.
Less than 1 sec. from 45 to 33 /3 rpm.
Less than 1 sec. from 33 /3 to 78 rpm
1
1
1
Audio Output
Phono/Line output
TONEARM SECTION:
Type
Effective Arm Length
Applicable Cartridge Weight
Static balanced straight shaped tone arm with cardan’s suspension
191mm
6~10g
AUDIO SECTION:
Digital Output
Preamp Frequency Response
Preamp Distortion
Preamp Noise Floor
0.5Vp-p (LOAD 75 Ω)
+1/-2dB 30Hz-20KHz/RIAA filter
Less than 0.03% at 1KHz
<-65dBv
CARTRIDGE SECTION:
Channel Separation
Channel Balance
More than 15dB
Within 2.5dB at 1KHz
1.5~2g
Needle Pressure Range
SPECIFICATIONS
GENERAL SECTION:
Power Supply
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K.)
10 Watts
Power Consumption
Dimensions
452 (W) x 370 (D) x 86 (H) mm
Weight
8.6 Kgs
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement
WARRANTY
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the
date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and
Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
RETURNS
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and
follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation
from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
c u t a l o n g d o t t e d l i n e
PLACE
STAMP
HERE
Stanton Magnetics, Inc.
3000 SW 42nd Street
Hollywood, FL 33312
U.S.A.
|