4-114-319-11(1)
Startup Guide
The Startup Guide explains how to connect, setup and use your Wireless Link.
DMX-WL1
© 2008 Sony Corporation
Connecting
1
the Receiver unit
Attaching the Receiver Unit to the
Rear of the TV
3
4
Slide the receiver unit onto the bracket.
Power off your TV before beginning setup.
1
Attach the supplied TV Mounting bracket to
the bottom left side of the TV rear panel.
Plastic Fastener
Connect the receiver unit and TV with the
supplied HDMI cable.
Guide Pin
• Do not push on the head of the Plastic Fastener until you
have inserted the fastener into the hole of the TV.
OUT
IN
IN
2
Align the slider on the bottom of the receiver
unit with the groove of the TV Mounting
bracket.
5
Connect the AC power adapter with AC
power cord between the receiver unit and the
wall outlet.
DC IN 9V
to wall outlet
AC power cord
AC power adapter
• See the Reference Guide for information for alternate
attachment methods.
3
Choosing
2
A
your setup type
Controlling the equipment using the supplied remote control
Other Equipment
You can connect up
to 5 sources to the
transmitter.
TV
Transmitter unit
Cable Box
Supplied remote control
Controlling the equipment using the supplied remote control and sending the
audio output to your Home Theater System
B
OPTICAL Cable
Other Equipment
TV
Transmitter unit
Cable Box
Supplied remote control
Controlling the equipment using your Home
Theater System
C
Other Equipment
TV
Cable Box
Transmitter unit
Supplied remote control
4
You can operate equipment
connected to the transmitter unit
with the supplied remote control.
Some equipment may not be
supported.
You can operate equipment
connected to the transmitter unit
with the supplied remote control.
Use your Home Theater System
remote control to control the
Volume.
Home Theater System
Home Theater System remote
control
Use your Home Theater System
remote control to select the sources
attached to your Home Theater
System.
• You cannot operate any equipment connected
to the transmitter unit with the supplied remote
control.
Home Theater System
Home Theater System remote
control
5
Connecting
3
the Transmitter unit
A
IR Blaster
Transmitter unit
5
COMPONENT IN
IR BLASTER
R
AUDIO
L
R
-
AUDIO
-
L
PR
PB
Y
(1080i/720p/480p/480i)
3
DIGITAL AUDIO OUT
(OPTICAL)
4
2
1
HDMI
SERVICE
DC IN 9V
IN
Component
B
IR Blaster
HDMI
Transmitter unit
5
COMPONENT IN
IR BLASTER
R
AUDIO
L
R
-
AUDIO
-
L
PR
PB
Y
(1080i/720p/480p/480i)
3
DIGITAL AUDIO OUT
(OPTICAL)
4
2
1
SERVICE
DC IN 9V
IN
Component
OPTICAL AUDIO
C
HDMI
HDMI
Transmitter unit
5
COMPONENT IN
IR BLASTER
R
AUDIO
L
R
-
AUDIO
-
L
PR
PB
Y
(1080i/720p/480p/480i)
3
DIGITAL AUDIO OUT
(OPTICAL)
4
2
1
SERVICE
DC IN 9V
IN
HDMI
HDMI
Component
Home Theater System
ꢀ
Place the IR Blaster
near the IR receiver
of the equipment.
Connecting to the
AC power outlet
When you finish connecting the equipment
to the transmitter unit, connect the AC
power adapter to the wall outlet.
VCR/DVD/Blu-ray Disc/
Satellite receiver/
Cable box
DC IN 9V
Transmitter unit
Place the IR Blaster
near the IR receiver
of the equipment.
to wall outlet
AC power cord
AC power adapter
VCR/DVD/Blu-ray Disc/
Satellite receiver/
Cable box
• Set the output resolution of the equipment to
480i, 480p, 720p or 1080i.
If you currently use equipment connected
directly to your TV with 1080p resolution,
make sure to change the equipment’s
resolution to 1080i or less before connecting
it to the transmitter unit.
Home Theater System
You should connect the equipment directly
to the TV to change the resolution.
DVD
Blu-ray Disc
Cable box
VCR
7
Turning
4
the TV and the Transmitter unit on
1
Turn the power of the TV on.
3
Press POWER on the transmitter unit.
Set Control for HDMI in the Settings menu
of the TV On.
POWER button
Then select the HDMI input that the receiver
unit is connected to.
POWER
TV
When the power of the transmitter unit is
turned on, the POWER LED will light up in
green, along with the white lamp on the front.
• If POWER LED of the receiver unit does not light up,
confirm Control for HDMI setting of the TV is On.
• The power of the receiver unit turns on or off in
conjunction with TV, if Control for HDMI setting of the
TV is On and the unit is connected to the TV by HDMI
cable.
POWER LED
• When Control for HDMI is enabled on your TV, the
power of the receiver unit will follow the power state of
the TV. When the TV is turned on or off, the receiver unit
will also turn on or off. To manually control the power of
the receiver unit using the receiver’s POWER button, you
must turn off the TV’s Control for HDMI.
POWER
• If Control for HDMI of the TV is Off, you must turn
the power of the receiver unit on or off by pressing the
POWER button on the unit.
• The supplied remote control cannot be used to turn on or
off the receiver unit separately from the TV.
White lamp
2
Confirm the POWER LED automatically lights
up in green on the receiver unit.
POWER
8
Optimal environment for placement
of the units
4
Verify the Wireless LINK LEVEL.
The LINK LEVEL LEDs located on the front
of the transmitter unit allows you to verify
the Wireless LINK LEVEL between the
transmitter and the receiver units.
Follow the suggestions below to create an
optimal environment for your Wireless Link.
Proper placement of the receiver and transmitter
units will ensure a strong Wireless LINK LEVEL
for superior performance.
LINK LEVEL LED
LINK LEVEL
• Use one system per room, placing the
transmitter and receiver units for each system
in the same room.
• If you use a 5 GHz WLAN or cordless phone,
place those in a different room.
• Do not place either unit on a metallic rack.
• Place the transmitter unit as high up as
possible.
• Maximum operating distance is approximately
ꢀ5 feet (20 m), depending on the environment.
• Be sure to keep at least 1 foot (30 cm)
minimum distance between the transmitter and
receiver units.
When the units are establishing a link, the
LINK LEVEL LED blinks.
After the wireless connection is established,
the LED stops blinking.
To ensure good picture quality, make
sure that all three LEDs light up in green,
indicating a good link.
Recommended placement of the receiver
and transmitter units is within ꢀ5 feet (20 m)
of each other. If you experience problems
with the LINK LEVEL, removing obstructions
from the path between the units may improve
the LINK LEVEL.
If the Wireless LINK LEVEL is less than three
or the picture is noisy or the sound quality
is diminished, press CONNECT to switch to
another wireless channel.
If you experience problems finding a suitable
LINK LEVEL, see the Troubleshooting
section in the Reference Guide for more
information.
9
Running
5
Initial Setup
Initial Setup instructions will appear on the
screen when the receiver and transmitter
units are turned on for the first time.
1
Press INPUT SELECT on the transmitter
unit to highlight your language choice. Then,
press CONNECT on the transmitter unit to
continue the setup.
Initial Setup
Step 1: Select
a
language
Highlight choice by pressing
a
INPUT SELECT on your
transmitter. Press CONNECT to
continue.
English
Español
Français
INPUT SELECT button
INPUT SELECT
CONNECT button
CONNECT
• The supplied remote control cannot be used at this
stage.
2
Insert batteries into the remote control.
Push to open
10
3
On your remote control, press and hold the
IN 1 button. While holding IN 1, press the
RETURN button. Hold both for at least 2
seconds.
4
Initial Setup is complete.
Initial Setup
Activation complete
To set up IR Blaster, press
SETUP; otherwise press
RETURN to exit.
Initial Setup
Step2: Activate your remote
control
On your remote, press and
hold IN 1. While holding IN 1,
press RETURN. Hold both
for at least
2
seconds.
Keep your remote control within
10 feet of the transmitter.
To use the supplied remote control to operate
equipment connected to the transmitter unit,
proceed to the next page.
• To display Initial Setup again, press CONNECT and
INPUT SELECT on the transmitter unit simultaneously.
IN 1
IN 1 button
RETURN button
11
Configuring
6
the remote control
Configure the IR Blaster to control your
connected equipment using the supplied
remote control.
1
2
3
Press SETUP on the remote control to
display the Setup menu.
Setup
You can control connected equipment
with your remote by using the IR Blaster
(supplied).
IR Blaster
Language
HDMI
HDMI
HDMI
HDMI
1
2
3
4
Component
If you chose setup type C, you cannot use the
IR Blaster to control connected equipment.
Exit the Setup menu by pressing SETUP on
the remote control to skip these steps.
Software Version
1.00.00
Press to highlight IR Blaster, and press
. The following screen appears.
Setup/IR Blaster
HDMI
HDMI
HDMI
1
2
3
2-8
Press to highlight an input to configure,
and press
.
Setup/IR Blaster/HDMI
1
Categor y
Maker
Code
Test (Power On/Off)
Save and Exit
Open the lid of the
remote control
SETUP
1
12
4
Press to highlight Category (equipment
type), and press
Select an equipment type from the list, and
press
7
Press to highlight Test (Power On/Off)
and press
Test to see if the selected equipment power
turns on and off.
.
.
.
You may need to test more than one code to
find the right code for your equipment.
Setup/IR Blaster/HDMI
1
Categor y
Maker
Cable Box
Satellite
VCR
• If the equipment’s supplied remote control has both
POWER ON and POWER OFF buttons, using Test
(Power On/Off) might not work to test the IR code.
Select Save and Exit then check if any other remote
buttons will operate your equipment.
Code
Test (Power
DVD
Save and Ex BD
Receiver
Setup/IR Blaster/HDMI
1
Categor y
Maker
BD
Sony
5
6
Press to highlight Maker, and press
Select a manufacturer from the list, and press
.
.
Code
BD
1
Test (Power On/Off)
Save and Exit
Setup/IR Blaster/HDMI
1
Categor y
Maker
Sony
LG
Code
Panasonic
Philips
8
When you have found the right code, press to
highlight Save and Exit, and press
Save the setting and exit from the Setup
Test (Power
.
Save and Ex Pioneer
Samsung
menu.
Setup/IR Blaster/HDMI
1
Categor y
Maker
BD
Press to highlight Code, and press
Select a code from the list, and press
.
.
Sony
Code
BD
1
Test (Power On/Off)
Save and Exit
Setup/IR Blaster/HDMI
1
Categor y
Maker
BD
BD
BD
1
2
3
Code
Test (Power On/Off)
Save and Exit
• Do not connect two of the same equipment from
the same manufacturer (Eg. two Sony Blu-ray disc
players), you will not be able to control each equipment
individually.
See page 15 on Reference Guide if your
code is not on the list.
• To erase the code, select Category, then press to
highlight “----” and press
in step 4.
• When more than one code is available for your
manufacturer, start checking from the top of the list for
the code that operates your equipment.
13
Using
7
the supplied remote control
Operating your TV
TV POWER
The following buttons are for operating your TV.
Press the TV button before using them.
TV
Button
Description
TV POWER
TV
Press to turn the TV on and off.
You must first press the TV function
PICTURE WIDE
FREEZE
button to operate the TV.
INPUT
Press to select the input of the TV.
Press to change the picture mode.
Press to change the wide mode.
PICTURE
WIDE
FREEZE
Press once to display a frozen image
with the current program in a window.
Press again to return to the current
program.
MENU
1
4
7
2
5
8
0
3
6
9
0-9, ENT
Press 0-9 to select a channel; the
channel changes after two seconds,
press ENT to change channels
immediately.
ENT
CH +/-
Press to scan through channels.
Press to display the TV Home menu.
Press to adjust the volume.
VOL
CH
HOME/MENU
VOL+/-
MUTING
MUTING
Press to mute the sound. Press again or
press VOL+ to restore the sound.
Press the SETUP button to display the Setup
menu if you need to change Language or IR
Blaster settings.
CONNECT SETUP
If the Wireless LINK LEVEL is less than three or
the picture is noisy, press CONNECT to switch to
another wireless channel.
• You can use the SETUP or CONNECT buttons when any input is
selected.
14
Operating equipment connected
to the transmitter unit
• You must connect the IR Blaster and complete setup for all connected
equipment before you can operate them.
The connected
AV POWER
HDMI
POWER
equipment can be
operated without
aiming the remote
control directly at
the equipment.
1
2
Press POWER to turn the transmitter unit on.
IN 1
IN 2
IN 3
IN 4
COMPO-
Press IN 1-4 HDMI or IN 5 COMPONENT to
select the desired input source.
NENT
IN 5
3
Press AV POWER to turn on the equipment
connected to the selected input source.
Button
Description
/
Goes to the beginning of the previous/
next title/chapter/scene/track.
/
Replays the scene/briefly fast forwards
the scene.
MENU
/
Fast reverses/fast forwards the disc
when pressed during playback.
Plays a disc at normal speed.
Pauses the playback.
Stops the playback.
HOME/MENU
Displays menus of selected external
equipment.
Moves the on-screen cursor of selected
external equipment. Press
confirm an item.
to select/
15
ForYour Convenience
Please contact Sony Customer Support directly if you:
• Have questions on the use of your module after reading the Startup Guide or Reference Guide
• Experience difficulty operating your module
For United States
or to speak with a support representative: 1-866-918-2485
For Canada
or to speak with a support representative: 1-877-899-SONY (7669)
Sony will work to resolve your questions more quickly than your retailer or place of purchase.
Please Do Not Return the Product to the Store
On-line Registration
United States
Canada
Printed in Japan
|