4-186-872-11(2)
Home Audio
Docking System
Operating Instructions
FST-GTK2i
FST-GTK1i
RDH-GTK1i
©2010 Sony Corporation
NOTE
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers)
that produce heat.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in
a particular installation.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
13) Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Important Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
Continued
l
3GB
For customers in Australia
Table of Contents
Disposal of Old
Electrical &
Electronic
Equipment
(Applicable in the
EuropeanUnionand
other European
countries with
separate collection
systems)
Getting Started
Hooking up the system
securely...................................9
Operations
On copyrights
iPod is a trademark of Apple Inc., registered
in the U.S. and other countries.
Listening to music of a USB
device....................................13
Using optional audio
Adjusting the sound...................17
Controlling the Speaker Light
Illumination ..........................17
Changing the display .................18
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
“WALKMAN” and “WALKMAN” logo are
registered trademarks of Sony Corporation.
Additional Information
MICROVAULT is a trademark of Sony
Corporation.
Troubleshooting.........................18
Messages....................................22
Precautions.................................23
Specifications.............................23
Compatible USB devices with this
unit........................................26
Compatible iPod models with this
unit........................................27
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
Windows Media is a registered trademark of
Microsoft Corporation in the United States
and/or other countries.
All other trademarks and registered
trademarks are trademarks or registered
trademarks of their respective holders.
®
In this manual, TM and marks are not
specified.
4GB
– Top view
5
6
*4
*1
7
8
qd qs qa
0
9
*
Except North American model
A On back panel: POWER
(page 10, 18, 19, 20, 21, 22)
Press to turn on or off the AC power.
D Standby indicator (except North
American model)
Lights up when the unit is in standby
Status of the POWER button
E
20, 22)
Connect an optional USB device.
(OFF)
The unit is turned off.
F iPod connector (page 11, 15, 16)
(ON)
Place an optional iPod to listen to
audio contents stored in the iPod.
(North American model)
The unit is turned on.
(Other models)
G FUNCTION (page 12, 14, 15, 16)
The unit is in standby mode.
Press to select a function.
On top panel: "/1 (on/standby)
(except North American model)
(page 10, 19, 22)
Press to turn on the unit or set it to
standby mode.
H NX (play/pause) (page 12, 14,
15, 16, 20, 22)
Press to start or pause playback.
Press and hold to stop USB playback
or turn off the iPod.
B Display (page 18)
C Remote sensor (page 19)
6GB
I m/M (rewind/fast forward)
Remote
(page 14, 15)
Hold down to find a point in a track
or file during playback.
– RM-AMU098 (North American
model only)
– RM-AMU092 (Other models)
./> (go backward/go
forward) (page 14, 15)
Press to select a track or file.
qk
1*
qj
qh
qg
EQ
GROOVE
2
3
TUNING +/– (page 12)
Press to tune in the station you want.
ENTER
4
5
J VOLUME (page 12, 14, 15, 16,
19)
qf
qd
qs
qa
q;
REPEAT
iPod
USB
Turn to adjust the volume.
6
K SPEAKER LIGHT (North
7
8
9
TUNER
American model only) (page 17)
Press to turn on or off the speaker
light when the unit is turned on.
AUDIO
IN
DEMO/SPEAKER LIGHT (Other
models) (page 17, 18)
*
RM-AMU092 only
Press to turn on or off the demo mode
when the unit is in standby mode.
Press to turn on or off the speaker
light when the unit is turned on.
1 "/1 (on/standby)
(RM-AMU092 only) (page 10, 19)
Press to turn on the unit or set it to the
standby mode.
L GROOVE (page 17, 22)
B TUNING MODE (page 12, 13)
Press to reinforce the bass.
Press to select the tuning mode.
M PRESET EQ (page 12, 17)
C FM MODE (page 12, 21)
Press to select a preset sound effect.
Press to select the FM reception
mode (monaural or stereo).
D V/v/B/b, MENU (page 16)
Press to select the menu items on the
iPod.
ENTER (page 13, 16)
Press to enter the settings.
E REPEAT (page 14)
Press to listen to a USB device, a
folder, a single track or file
repeatedly.
Continued
l
7GB
F VOLUME +/– (page 12, 14, 15,
16, 19)
Press to adjust the volume.
G ./> (go backward/go
forward) (page 14, 15)
Press to select a track or file.
+/– (tuning) (page 12, 13)
Press to tune in the station you want.
H m/M (rewind/fast forward)
(page 14, 15)
Hold down to find a point in a track
or file during playback.
I
+/– (page 14)
Press to select a folder.
J AUDIO IN (page 16)
Press to select the AUDIO IN
function.
K TUNER/BAND (page 12)
Press to select the TUNER function.
Press to select the FM or AM band.
L USB (page 14)
Press to select the USB function.
M iPod (page 15)
Press to select the iPod function.
N NX (play/pause) (page 14, 15,
16, 20)
Press to start or pause playback.
Press and hold to stop USB playback
or turn off the iPod.
O TUNER MEMORY (page 12, 13)
Press to preset the radio station.
P EQ (page 17)
Press to select a preset sound effect.
Q GROOVE (page 17)
Press to reinforce the bass.
R DISPLAY (page 18)
Press to change the information on
the display.
8GB
Getting Started
Hooking up the system securely
– Rear panel
*
A B C
ANTENNA
AUDIO IN
R
L
E
POWER
ON OFF
D
E
*
FST-GTK2i only
A Antennas
Find a location and an orientation that
provide good reception, and then set up
the antennas.
Keep the antennas away from the power
cord, the USB cable, the iPod and the
subwoofer cable (FST-GTK2i only) to
avoid picking up noise.
AM loop antenna
ANTE
NNA
Extend the FM lead
antenna horizontally
Continued
l
9GB
B AUDIO IN L/R jacks
Using the subwoofer
Use an audio cord (not supplied) to
connect the audio output of the optional
audio component to these jacks. You can
then output audio through this unit.
(FST-GTK2i only)
You can use the subwoofer to enhance the
bass.
Make sure the subwoofer cable is
connected before using the subwoofer.
C SUBWOOFER OUT jack
(FST-GTK2i only)
SUBWOOFER
ON/OFF
Use a supplied subwoofer cable to
connect the SUBWOOFER OUT jack on
the unit and INPUT jack on the
subwoofer.
Power indicator
SUBWOOFER
LEVEL
Notes
• Be sure to use only the supplied subwoofer
and subwoofer cable.
• Be sure to connect the subwoofer cable
securely and correctly to the unit and the
subwoofer.
• Do not connect other component to this jack.
D VOLTAGE SELECTOR
For models equipped with a voltage
selector, set VOLTAGE SELECTOR to
the local power line voltage.
Depending on the model, the VOLTAGE
SELECTOR may differ.
1
2
Connect the power cord of the
subwoofer to a wall outlet.
Press SUBWOOFER ON/OFF on
the subwoofer.
E Power
Connect the power cord to a wall outlet.
Press the POWER on the back panel to
turn on the AC power.
If the supplied adaptor on the plug does
not fit your wall outlet, detach it from the
plug (only for models equipped with an
adaptor).
The subwoofer turns on and the power
indicator lights up.
3
Turn SUBWOOFER LEVEL on
the subwoofer to adjust the
level.
Notes
• Place the subwoofer vertically to obtain a
better bass reproduction.
• Position the subwoofer
– on a solid floor where resonance is unlikely
to occur.
– at least a few centimeters away from the
wall.
(Except North American model)
The demonstration appears in the display.
When you press "/1, the unit turns on
and the demonstration automatically
ends.
– away from the center of the room or place a
bookshelf against a wall, to avoid
generating a standing wave.
10GB
Inserting the iPod Dock
Adapter
Using the remote
Slide and remove the battery
compartment lid, and insert the two
supplied R03 (size AAA) batteries, E
side first, matching the polarities shown
below.
Insert the iPod Dock Adapter (not
supplied) into the iPod connector on the
unit before you connect the iPod.
Use a Dock Adapter supplied with your
iPod. Otherwise, a compatible Dock
Adapter will need to be purchased
separately from Apple Inc.
Slot
Notes
• Do not mix an old battery with a new one or
mix different types of batteries.
• If you do not use the remote for a long period
of time, remove the batteries to avoid damage
from battery leakage and corrosion.
• With normal use, the batteries should last for
about six months. When the remote no longer
operates the unit, replace both batteries with
new ones.
• Batteries installed devices shall not be
exposed to excessive heat such as sunshine,
fire or the like.
To remove the iPod Dock Adapter, pull it
up with your fingernail or a flat object
using the slot inside the adapter.
Slot
11GB
To change the AM tuning interval
The factory setting for AM tuning interval
is 9 kHz (or 10 kHz for some areas).
Use the buttons on the unit for the
operation.
Operations
Listening to the radio
1 Press FUNCTION repeatedly to
select AM band.
1
Select FM or AM band.
2 Press and hold NX and PRESET
EQ at the same time for about 5
seconds.
“9K STEP” or “10K STEP” appears in
the display.
Press TUNER/BAND (or FUNCTION
on the unit) repeatedly.
2
Perform tuning.
For automatic scanning
When you change the interval, all the AM
preset stations are erased.
Press TUNING MODE repeatedly
until “AUTO” lights up in the display,
and then press +/– (or TUNING +/– on
the unit).
Tip
To improve broadcast reception, adjust the
supplied antennas.
Scanning stops automatically when a
station is tuned in, and then “TUNED”
and “ST” (for FM stereo programs
only) lights up in the display.
To reduce static noise on a weak FM
stereo station
Press FM MODE repeatedly until
“MONO” lights up in the display.
There will be no stereo effect, but the
reception will improve.
TUNED ST
AUTO
MHz
If “TUNED” does not light up and the
scanning does not stop, press +/– (or
TUNING +/– on the unit) to stop
Presetting radio stations
scanning, then perform manual tuning.
You can preset your favourite radio
stations and tune them in instantly by
selecting the corresponding preset
number.
Use the buttons on the remote for this
operation.
For manual tuning
Press TUNING MODE repeatedly
until “AUTO” and “PRESET”
disappear from the display, and then
press +/– (or TUNING +/– on unit)
repeatedly to tune in the station you
want.
1
2
Tune in the station you want.
Press TUNER MEMORY.
3
Adjust the volume.
A preset number flashes in the display.
The stations are stored from preset
number 1.
Press VOLUME +/– (or turn
VOLUME on the unit).
TUNED ST
AUTO
MHz l
Preset number
12GB
3
4
Press +/– repeatedly to select
the preset number you want.
USB device
If another station is already assigned to
the selected preset number, the station
is replaced by the new station.
You can listen to music stored in the USB
device by connecting it to the
port on the unit.
(USB)
Press ENTER.
“COMPLETE” appears in the display.
The audio formats that can be played back
by this unit are as follows:
MP3*/WMA*/AAC*
* Files with copyright protection (Digital
Rights Management) cannot be played back
by this unit. Files downloaded from an online
music store may not be played back by this
unit.
5 The station is stored.
Repeat steps 1 to 4 to store other
stations.
You can preset up to 20 FM and 10
AM stations.
6
To call up a preset radio station,
press TUNING MODE repeatedly
until “PRESET” lights up in the
display. Then, press +/–
repeatedly to select the preset
number you want.
Before using the USB device with
this unit
• See “Compatible USB devices with this unit”
(page 26) for a list of USB devices that can be
connected to this unit.
• Operation may not always be ensured even
when using these USB devices.
To cancel presetting
Press TUNER MEMORY.
• When USB cable connection is necessary,
connect the USB cable supplied with the USB
device to be connected. Refer to the operating
instructions supplied with the USB device to
be connected for details on the operation
method.
• Do not connect the unit and the USB device
through a USB hub.
• When the USB device is connected,
“READING” appears and “USB MEMORY”
lights up in the display.
• It may take about 10 seconds before
“READING” appears depending on the type
of USB device connected.
• When the USB device is connected, the unit
reads all the files on the USB device. If there
are many folders or files on the USB device, it
may take a long time to finish reading the
USB device.
• The unit can recognize up to
–
–
–
100 folders (including “ROOT” folder).
100 audio files for each folder.
8 folder levels (tree structure of files,
including “ROOT” folder).
The maximum number of audio files and
folders may vary depending on the file and
folder structure.
Do not save other types of files or unnecessary
folders on a USB device.
Continued
l
13GB
• Compatibility with all encoding/writing
softwares, recording devices, and recording
media cannot be guaranteed. Incompatible
USB device may produce noise or interrupted
audio or may not play at all.
To
Do this
Find a point in a Hold down m/M (or
file
. m or M > on
the unit) during playback,
and release the button at
the point you want.
1
2
Press USB (or FUNCTION on the
unit repeatedly).
Select Repeat
Play
PressREPEATrepeatedly
until “REP”, “
or “REP1” lights up in the
display.
REP”
Connect an optional USB device
to the
(USB) port on the unit.
USB device
* When playing a VBR (variable bit rate) audio
file, the unit may resume playback from a
different point.
Notes on the USB device
• Some time may be needed to start playback
when:
– the folder structure is complex.
– the memory capacity is excessive.
• This unit does not necessarily support all the
functions provided in a connected USB
device.
• The playback order for the unit may differ
from the playback order of the connected USB
device.
• Folders that have no audio files are skipped.
• The unit can play the following format of
audio files:
– MP3 with file extension “.mp3”.
– AAC with file extension “.m4a”, “.3gp”,
“.mp4”.
When the USB device is connected,
the display changes as follows:
“READING” t “1”
3
4
Press NX to start playback.
Press VOLUME +/– (or turn
VOLUME on the unit) to adjust
the volume.
– Windows Media Audio (WMA) with file
extension “.wma”.
Other operations
If the audio files have the above file extension
but are not the respective formats, the unit
may produce noise or may malfunction.
• When playing a very long track, some
operations may cause playback delay.
To
Do this
Pause playback Press NX. To resume
playback, press the button
again*.
Note on Repeat Play
All files on a USB device are repeated until you
pause or stop playback.
Stop playback
Press and hold NX for 2
seconds or more. Resume
play is canceled.
Select a folder Press
+/– repeatedly.
Select a file
Press ./> (or
. m or M > on
the unit) repeatedly.
14GB
• Depending on the connected iPod, you may
not able to use m or M while playing
video. In this case, you can fast rewind or fast
forward by holding down . or >.
• To change the volume level, use
VOLUME +/– (or turn VOLUME on the
unit). The volume level does not change even
if adjusted on the iPod.
• This iPod connector is designed for iPod only.
Do not connect any other portable audio
players to the iPod connector.
• To use an iPod, refer to the operating
instructions of your iPod.
• Sony cannot accept responsibility in the event
that data recorded to iPod is lost or damage
when using an iPod with this unit.
• Some iPod operations may not be performed
using buttons on the unit or remote.
• Depending on the connected iPod, operations
may differ.
Playing the iPod
You can listen to audio contents stored in
the iPod on this unit.
Update your iPod with the latest software
before using it.
1
2
Press iPod (or FUNCTION on the
unit repeatedly).
Place the iPod.
Note
If your iPod has a protect case, we
recommend you to remove the protect case
before you place the iPod onto the unit.
Other operations
You can control your iPod using the
buttons on the remote or unit. The
following buttons have the similar
function with the buttons on the iPod
(except for iPod Touch).
To
Do this
Pause playback Press NX. To resume
playback, press the button
again.
3
4
Press NX to start playback.
Select a track or Press . or > (or
chapter of
audiobook/
podcast
. m or M > on
the unit) repeatedly.
Press VOLUME +/– (or turn
VOLUME on the unit) to adjust
the volume.
Locate a point Hold down m or M
while listening (or . m or M >
Notes
• When you connect an iPod to the unit, the
iPod is automatically turned on if the unit is
turned on.
• When placing or removing the iPod
– handle the iPod in the same angle as that of
the iPod connector on the unit and do not
twist or sway the iPod to prevent connector
damage.
to the music
(fast forward/
fast rewind)
on the unit) during
playback, then release it at
the point you want.
Locate a point Hold down . or >
while viewing (or . m or M >
the iPod display on the unit) when
(except for iPod playback is paused, then
– brace the unit with one hand and take care
not to press the controls of the iPod by
mistake.
Touch)
release it at the point you
want.
• Before carrying the unit, be sure to disconnect
the iPod.
• Before disconnecting the iPod, pause
playback.
Continued
l
15GB
To
Do this
Select the iPod Press MENU and V/v to
Using optional audio
components
You can enjoy the sound from an optional
audio component through the speakers of
this unit.
Be sure to turn off the power of the
component before making any
connections.
menu item
select a menu, then press
ENTER or b.
Note
You can confirm menu and
item selections on the iPod
display during operation.
Return to
previous menu
Press MENU or B.
For details, refer to the operating
instructions supplied with the connected
component.
Turn off the
iPod
Hold down NX.
Tip
1
Connect an optional audio
component to the AUDIO IN L/R
jacks using an audio cord (not
supplied).
Press and hold V or v on the remote has the
similar function of turning the Click Wheel on
the iPod counterclockwise or clockwise.
To use the unit as a battery charger
2
3
Turn on the unit and the
connected component.
You can use the unit as a battery charger
for the iPod when the unit is on.
The charging begins when the iPod is
placed on the iPod connector. The
charging status appears in the iPod
display. For details, refer to the operating
instructions of your iPod.
Press VOLUME – repeatedly (or
turn VOLUME on the unit
counterclockwise) to turn down
the volume.
4
5
Press AUDIO IN (or FUNCTION
on the unit repeatedly).
To stop charging the iPod
Remove the iPod.
Start playing the connected
component.
The sound from the connected
component is output from the speakers
of this unit.
6
Press VOLUME +/– (or turn
VOLUME on the unit) to adjust
the volume.
16GB
Adjusting the sound
Controlling the
Speaker Light
Illumination
You can turn on or off the speaker light
when the unit is turned on.
Use the button on the unit for the
operation.
To add a sound effect
To
Do this
Reinforce the
Press GROOVE
bass and create repeatedly to select
a more powerful “GROOVE”*.
sound
Select the preset Press EQ (or PRESET
(North American model only)
Press SPEAKER LIGHT repeatedly.
sound effect
EQ on the unit)
repeatedly to select the
preset effect you want.
The preset effect name
appears in the display.
To cancel the effect,
press EQ (or PRESET
EQ on the unit)
(Other models)
Press DEMO/SPEAKER LIGHT
repeatedly.
Each time you press the button, the
display changes as follows:
repeatedly to select
“FLAT”.
LIGHT ON* y OFF
* The speaker light will create lighting effect
according to the music source.
* The volume switches to power mode and the
equalizer curve changes.
17GB
Changing the display
Additional Information
Changing the display mode
Troubleshooting
(Except North American model)
Press DEMO/SPEAKER LIGHT on
the unit repeatedly while the unit is
in standby mode.
Should you encounter a problem with
your system, do the following:
1 Make sure the power cord and
subwoofer cable (FST-GTK2i only)
are connected correctly and firmly.
Demonstration
The demo display appears and the speaker
light flashes even when the unit is set to
standby mode.
2 Find your problem in the
troubleshootingchecklistbelowand
take the indicated corrective action.
No display
If the problem persists after doing all of
the above, consult your nearest Sony
dealer.
The demo display and speaker light are
turned off.
Note that if service personnel changes
some parts during repair, these parts may
be retained.
Viewing the display
information
If “PROTECT” appears on the
display
Immediately press POWER on the
back panel to turn off the unit and
unplug the power cord. Then perform
the following items.
Press DISPLAY repeatedly while
the unit is turned on.
You can view the USB device
information as follows:
• track or file number
• track name (“ ”)
• file name (“ ”)
• artist name (“ ”)
• album name (“ ”)
• folder name (“ ”)
• Remove anything that is blocking
the ventilation hole.
• If your unit has a voltage selector,
set the voltage selector to the correct
voltage.
• Disconnect the USB device and
iPod.
• Disconnect audio cord from the
AUDIO IN L/R jacks.
Notes on the display information
• Characters that cannot be displayed appear as
“_”.
• The following are not displayed correctly:
– elapsed playing time of a file encoded using
a VBR (variable bit rate).
– folder and file names that do not follow
either the ISO9660 Level 1, Level 2 or Joliet
in the expansion format.
After checking the above items and
fixing any problems, plug in the power
cord again and turn on the unit. If the
“PROTECT” still appears, or if the
cause of the problem cannot be found
even after checking all the above
items, consult your nearest Sony
dealer.
18GB
General
USB device
(Except North American model)
The display starts flashing as soon as
you plug in the power cord even
though you have not press ?/1 to
turn on the unit.
Are you using a supported USB
device?
• If you connect an unsupported USB
device, the following problems may
occur. See “Compatible USB devices
with this unit” (page 26) for the
supported device types.
• The demonstration mode started. Press
?/1 (page 10).
– The USB device is not recognized.
– File or folder names are not displayed
on this unit.
– Playback is not possible.
– The sound skips.
There is no sound.
• Make sure you press the POWER on the
back panel.
• Press VOLUME + repeatedly (turn
VOLUME clockwise on the unit).
– There is noise.
– A distorted sound is output.
There is severe hum or noise.
• Move the unit away from the source of
noise.
• Connect the unit to a different wall
outlet.
• Install a noise filter (commercially
available) to the power cord.
• Turn off surrounding electrical
equipment.
“OVER CURRENT” appears.
• A problem has been detected with the
level of electrical current from the
(USB) port. Press POWER on the back
panel to turn off the unit and remove the
USB device from the
(USB) port.
Make sure there is no problem with the
USB device. If this display pattern
persists, contact your nearest Sony
dealer.
The remote does not function.
• Remove the obstacles between the
remote and the unit.
There is no sound.
• Move the remote closer to the unit.
• Point the remote at the unit’s sensor.
• Replace the batteries.
• Move the unit away from the
fluorescent light.
• The USB device is not connected
correctly. Press POWER on the back
panel to turn off the unit and reconnect
the USB device, then turn on the unit
and check if “USB MEMORY” lights
up in the display.
• Place the USB device and iPod to the
port/connector firmly.
There is noise, skipping, or distorted
sound.
• Press POWER on the back panel to turn
off the unit and reconnect the USB
device, then turn on the unit.
• The music data itself contains noise, or
the sound is distorted.
(FST-GTK2i only)
There is no sound from the
subwoofer.
• Adjust the subwoofer level to the
appropriate level.
• Check that the subwoofer cable and
power cord are connected securely and
correctly.
• Make sure you have turned on the
subwoofer by pressing SUBWOOFER
ON/OFF on the subwoofer.
Continued
l
19GB
The USB device cannot be
Playback does not start.
connected into the
(USB) port.
• Press POWER on the back panel to turn
off the unit and reconnect the USB
device, then turn on the unit.
• Connect the supported USB device
(page 26).
• The USB device is being connected
backwards. Connect the USB device in
the correct orientation.
“READING” is displayed for an
extended time, or it takes a long time
before playback starts.
• The reading process can take a long time
in the following cases.
– There are many folders or files on the
USB device.
– The file structure is extremely
complex.
– The memory capacity is excessive.
– The internal memory is fragmented.
Thus, we recommend following these
guidelines.
– Total folders on USB device: 100 or
less (including “ROOT” folder)
– Total files per folder: 100 or less
• Press NX to start playback.
Audio file cannot be played back.
• MP3 files in MP3 PRO format cannot be
played back.
• The audio file is a multiple track audio
file.
• Some AAC files may not be played back
correctly.
• WMA files in Windows Media Audio
Lossless and Professional format cannot
be played back.
• USB device formatted with file systems
other than FAT16 or FAT32 are
unsupported.*
• If you use partitioned USB device, only
audio files on the first partition can be
played back.
• Playback is possible up to 8 levels
(including “ROOT” folder).
• The number of folders has exceeded 100
(including “ROOT” folder).
• The number of files in a folder has
exceeded 100.
Erroneous display.
• The data stored in the USB device may
have been corrupted.
• The character codes that can be
displayed by this unit are as follows:
– Upper cases (A to Z)
– Numbers (0 to 9)
– Symbols (’ < > * + , – . / @ [ \ ] _ `)
Other characters may not be displayed
correctly.
• Files that are encrypted or protected by
passwords, etc. cannot be played back.
* This unit supports FAT16 and FAT32, but
some USB device may not support all of these
FAT. For details, refer to the operating
instruction of each USB device or contact the
manufacturer.
The USB device is not recognized.
• Press POWER on the back panel to turn
off the unit and reconnect the USB
device, then turn on the unit.
• Connect the supported USB device
(page 26).
• The USB device does not work
properly. Refer to the USB device
operating instruction on how to deal
with this problem.
20GB
iPod
Tuner
If the iPod does not operate properly,
check that you have removed the protect
case of the iPod. If the problem persists,
use the following troubleshooting guide to
remedy the problem.
Severe hum or noise, or stations
cannot be received. (“TUNED” or
“ST” flashes in the display)
• Set the proper band and frequency
(page 12).
• Connect the antenna properly (page 9).
• Find a location and an orientation that
• The supplied FM lead antenna receives
signals along its entire length, so make
sure you extend it fully.
cord, the USB cable, the iPod and
subwoofer cable (FST-GTK2i only) to
avoid picking up noise.
There is no sound.
• Make sure the iPod is connected
securely.
• Make sure the iPod is playing music.
• Adjust the volume.
• Depending on the contents of the iPod,
it may take time to start playback.
• You are using an unsupported iPod. See
“Compatible iPod models with this
unit” (page 27) for the supported device
types.
• Consult your nearest Sony dealer if the
supplied AM antenna has come off the
plastic stand.
The sound is distorted.
• Reduce the volume.
• Set the “EQ” setting of the iPod to “Off”
or “Flat”.
• Turn off nearby electrical equipment.
A stereo FM program cannot be
received in stereo.
• Press FM MODE repeatedly until
“MONO” disappears from the display.
The iPod cannot be operated.
• Disconnect the iPod and connect the
iPod again.
• You are using an unsupported iPod. See
“Compatible iPod models with this
unit” (page 27) for the supported device
types.
Optional components
There is no sound.
The iPod cannot be charged.
• Make sure you press the POWER on the
back panel.
• See general item “There is no sound.”
(page 19) and check the condition of the
unit.
• Make sure the iPod is connected
securely.
• Connect the component properly
(page 9) while checking:
– if the cords are connected properly.
– if the cord plugs are firmly inserted all
the way.
• Turn on the connected component.
• Refer to the operating instructions
supplied with the connected component
and start playing.
“OVER CURRENT” appears.
• A problem has been detected with the
level of electrical current from the iPod.
Press POWER on the back panel to turn
off the unit and remove the iPod. Make
sure there is no problem with the iPod. If
this display pattern persists, contact
your nearest Sony dealer.
Continued
l
21GB
To reset the unit to factory settings
If the unit still does not operate properly
after performing the above measures or
other troubles not described above occur,
reset the unit as follows:
Use the buttons on the unit for the
operation.
Messages
One of the following messages may
appear or flash in the display during
operation.
COMPLETE
The radio preset operation ended
normally.
1 Press POWER on the back panel to
turn off the AC power.
2 Press POWER again to turn on the
DEVICE ERROR
The memory of the USB device could not
be recognized (page 19).
AC power.
3 (Except North American model)
NoDEVICE
No USB device is connected.
Press ?/1 to turn on the unit.
4 Press and hold NX and GROOVE
at the same time for about 5
seconds.
NO TRACK
No playable audio file is loaded in the
unit.
“RESET” appears in the display.
NO ARTIST
Playable file on the USB device do not
has artist information.
The unit is reset to the factory settings.
You need to readjust all the settings you
made, such as the preset stations.
NOT SUPPORT
An unsupported USB device is connected,
an unknown device is connected, or the
USB device is connected through a USB
hub (page 26).
OVER CURRENT
An over current from the
or iPod was detected.
(USB) port
PROTECT
The following causes can be considered:
• The ventilation holes may be blocked.
• The voltage selector may not be set to
the correct local power line voltage.
See “If “PROTECT” appears on the
display” (page 18) to check what to do if
this message appears.
READING
The unit is reading information of the
USB device.
22GB
Precautions
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
On safety
• Completely disconnect the power cord (mains
lead) from the wall socket (mains) if it is not
going to be used for an extended period of
time. When unplugging the unit, always grip
the plug. Never pull the cord itself.
• Should any solid object or liquid get into the
system, unplug the system, and have it
checked by qualified personnel before
operating it again.
RDH-GTK1i USA model only
With 6-ohm loads, both channels driven,
from 120 Hz – 10 kHz; rated 30 watts per
channel minimum RMS power, with no
more than 0.7% total harmonic distortion
from 250 miliwatts to rated output.
• (For customers in United States and Canada
only)
One blade of the plug is wider than other for
the purpose of safety and will fit to the wall
outlet only one way. If you are unable to insert
the plug fully into the outlet, contact your
dealer.
Amplifier section
FST-GTK2i
The following are measured at
AC 127 V, 60 Hz
• The AC power cord can be changed only by a
qualified service facility.
Front speaker:
On placement
Power Output (rated)
• Do not place the system in an inclined
position or in locations that are extremely hot,
cold, dusty, dirty, or humid or lacking
adequate ventilation, or subject to vibration,
direct sunlight or a bright light.
• Be careful when placing the unit or subwoofer
on surfaces that have been specially treated
(for example, with wax, oil, polish) as staining
or discoloration of the surface may result.
35 W + 35 W (at 6 :, 1 kHz, 1% THD)
RMS output power (reference)
110 W + 110 W (per channel at 6 :,
1 kHz)
Subwoofer:
RMS output power (reference)
230 W (8 :, 100 Hz)
FST-GTK1i and RDH-GTK1i
On heat buildup
• Heat buildup on the unit during operation is
normal and is not a cause for alarm.
• Do not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
North American model only
The following are measured at
AC 120 V, 60 Hz
Front speaker:
• Do not obstruct the ventilation holes.
RMS output power (reference)
110 W + 110 W (per channel at 6 :,
1 kHz)
On the speaker system
This speaker system is not magnetically
shielded, and the picture on nearby TV sets may
become magnetically distorted. In this situation,
turn off the TV, wait 15 to 30 minutes, and turn
it back on. If there is no improvement, move the
speakers far away from the TV.
Cleaning the cabinet
Clean this system with a soft cloth slightly
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring
powder, or solvent, such as thinner, benzine,
or alcohol.
Continued
l
23GB
Brazilian model only
AM tuner section
The following are measured at
Tuning range
AC 127 V or 220 V, 60 Hz
Pan American and Oceanian models:
530 kHz – 1,710 kHz (with 10 kHz
tuning interval)
531 kHz – 1,710 kHz (with 9 kHz
tuning interval)
Front speaker:
RMS output power (reference)
75 W + 75 W (per channel at 6 :,
1 kHz, 10% THD)
Other models:
530 kHz – 1,610 kHz (with 10 kHz
tuning interval)
Other models
The following are measured at
531 kHz – 1,602 kHz (with 9 kHz
tuning interval)
Mexican model:
AC 127 V, 60 Hz
Intermediate frequency
53 kHz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Front speaker:
Power Output (rated)
USB section
Supported bit rate*
35 W + 35 W (at 6 :, 1 kHz, 1% THD)
RMS output power (reference)
110 W + 110 W (per channel at 6 :,
1 kHz)
MP3 (MPEG 1 Audio Layer-3):
32 kbps – 320 kbps, VBR
WMA: 48 kbps – 192 kbps
AAC: 48 kbps – 320 kbps
* Compatibility with all encoding/
writing software, recording devices
and recording media cannot be
guarantee.
Input
AUDIO IN L/R:
Voltage 1 V, impedance 47 kilohms
Sampling frequencies
Output
MP3 (MPEG 1 Audio Layer-3):
32 kHz/44.1 kHz/48 kHz
WMA: 44.1 kHz
SUBWOOFER OUT (FST-GTK2i only)
Tuner section
FM stereo, FM/AM superheterodyne tuner
AAC: 44.1 kHz
Transfer speed
Antenna:
Full-speed
FM lead antenna
Supported USB device
Mass Storage Class
Maximum current
500 mA
AM loop antenna
FM tuner section
Tuning range
North American and Brazilian models:
87.5 MHz – 108.0 MHz (100 kHz step)
Other models:
iPod section
DC5V 500 mA MAX
87.5 MHz – 108.0 MHz (50 kHz step)
Intermediate frequency
225 kHz
24GB
Mass (Approx.)
HCD-GTK2i/HCD-GTK1i:
Speakers
Unit
12.5 kg (27 lb 9 oz)
SA-WGTK2i:
11.5 kg (25 lb 6 oz)
HCD-GTK2i (for FST-GTK2i)/
HCD-GTK1i (for FST-GTK1i/
RDH-GTK1i)
Speaker system
2-way, coaxial
Speaker unit
Woofer: 160 mm (6 / in), cone type
Tweeter: 40 mm (1 / in), cone type
Rated impedance
Supplied accessories
Remote Commander:
• RM-AMU098 (North American
model only) (1)
• RM-AMU092 (other models) (1)
FM lead/AM loop antenna (1)
R03 (size AAA) batteries (2)
Subwoofer cable (FST-GTK2i only)
(1)
1
2
5
8
6 ohms
Subwoofer
SA-WGTK2i (for FST-GTK2i)
Subwoofer system
1-way, 1-driver, Bass reflex
Speaker unit
Design and specifications are subject to
change without notice.
Subwoofer: 200 mm (8 in), cone type
Rated impedance
8 ohms
General
Power requirements
North American model: AC 120 V,
60 Hz
Oceanian model: AC 230 V – 240 V,
50/60 Hz
Mexican model: AC 127 V, 60 Hz
Brazilian model: AC 127 V or 220 V,
60 Hz, adjustable with voltage selector
Argentina model: AC 220 V, 50/60 Hz
Other models: AC 120 V, 220 V or
230 V – 240 V, 50/60 Hz, adjustable
with voltage selector
Power consumption
HCD-GTK2i/HCD-GTK1i: 150 W
SA-WGTK2i: 200 W
Dimensions (w/h/d) (Approx.)
HCD-GTK2i/HCD-GTK1i:
600 mm × 385 mm × 395 mm
(23 5/8 in × 15 1/4 in × 15 5/8 in)
SA-WGTK2i:
320 mm × 435 mm × 420 mm
(12 5/8 in × 17 1/4 in × 16 5/8 in)
25GB
Product name Model name
IC Recorder ICD-UX71 / UX81 /
Compatible USB
UX91
devices with this unit
ICD-SX68 / SX78 / SX88
You can use the following Sony USB
devices on this unit. Other USB devices
cannot be used on this unit.
ICD-SX700 / SX800 /
SX900
ICD-UX200 / UX300 /
UX400
Verified Sony USB device
Product name Model name
ICD-SX750 / SX850 /
SX950
®
Walkman
NWZ-B133 / B135 /
B133F / B135F
MICROVAULT USM1GL / 2GL / 4GL /
8GL / 16GL
NWZ-B142 / B143 /
B142F / B143F
USM1GLX / 2GLX /
4GLX / 8GLX / 16GLX
NWD-E023F / E025F
Notes
NWZ-E435F / E436F /
E438F
• The unit is unable to read data in NTFS
format.
• The unit is unable to read data other than that
saved in the first partition of a hard disk drive.
• Do not use USB devices other than these USB
devices. Operation of models not listed here is
not guaranteed.
NWZ-E343 / E344 / E345
NWZ-S636F / S638F /
S639F
NWZ-S736F / S738F /
S739F
• Operation may not always be ensured even
when using these USB devices.
• Some of these USB devices may not be
available for purchase in certain areas.
• When formatting the above models, be sure to
format using the model itself or the dedicated
formatting software for that model.
• Please do not connect iPod to USB port.
• When connecting a USB device to the unit, be
sure to connect after the display “Creating
Library” or “Creating Database” on the USB
device has disappeared.
NWZ-A726 / A728 /
A729 / A726B / A728B
NWZ-A826 / A828 /
A829
NWZ-W202
NWZ-X1050 / X1060
NWZ-S744 / S745
NWZ-E443 / E444 / E445
NWZ-S544 / S545
NWZ-A845 / A846 /
A847
NWZ-W252 / W253
NWZ-B152F / B153F
26GB
Compatible iPod models with this unit
You can use the following iPod models on this unit. Update your iPod with the latest
software before using it.
iPod touch
2nd generation
iPod touch
1st generation
iPod nano
4th generation
(video)
iPod nano
5th generation
(video camera)
iPod
5th generation
(video)
iPod nano
2nd generation
(aluminum)
iPod classic
iPod nano
3rd generation
(video)
iPod nano
1st generation
iPod
4th generation
(color display)
iPod
4th generation
iPod mini
Notes
• This unit is designed for iPod only. You cannot connect any other portable audio players.
• Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when
using an iPod connected to this unit.
• Use a Dock Adapter supplied with your iPod. Otherwise, a compatible Dock Adapter will need to be
purchased separately from Apple Inc.
• This product has been designed specifically to work with iPod and has been certified to meet Apple
performance standards.
• This unit is not compatible with iPhone.
27GB
Sony Corporation Printed in Malaysia
|