Sony Headphones MDR EX38IP User Manual

4-156-141-11(1)  
How to use the remote  
and microphone for an  
iPod (See fig. -)  
Specifications  
Receiver  
Type:  
Closed, dynamic  
You can control a connected iPod  
product.  
Operating Instructions  
Manual de instrucciones  
Driver unit:  
9 mm, dome type (CCAW)  
Stereo  
Parts and controls  
Power handling capacity:  
100 mW (IEC*)  
Impedance:  
Volume +  
Increases the volume of the connected  
iPod product.  
Headphones  
16 Ω at 1 kHz  
Center button  
Sensitivity:  
Plays/pauses a track of the connected  
iPod product with a single press. Skips  
to the next track with a double press.  
Skips to the previous track with a triple  
press. Starts the “VoiceOver*” feature  
with a long press (if available).  
Volume –  
100 dB/mW  
Frequency response:  
6 – 23,000 Hz  
Cord:  
Plug:  
Mass:  
1.2 m (3.9 ft), Litz cord  
Y-type  
Gold-plated L-shaped stereo  
mini plug  
MDR-EX38iP  
Decreases the volume of the connected  
iPod product.  
Microphone  
Approx. 3 g (0.11 oz)  
without cord  
©2009 Sony Corporation Printed in Thailand  
Microphone  
Compatible products  
You can use the unit with the following  
models.  
Open circuit voltage level:  
– 42 dB ( 0dB=1V/Pa)  
Supplied accessories  
Earbuds (S × 2, M × 2, L × 2)  
Cord adjuster (1)  
English  
iPod nano (4th generation)  
iPod classic (120 GB)  
iPod touch (2nd generation)  
iPod shuffle (3rd generation)  
Stereo headphones  
Carrying pouch (1)  
* IEC = International Electrotechnical  
Commission  
Design and specifications are subject  
to change without notice.  
Features  
* Availability of the “VoiceOver” feature  
depends on iPod model and its software  
version.  
Easy-to-use remote control for iPod  
only  
Clear and rich sound with deep bass  
Convenient cord adjuster supplied  
How to install the earbuds  
correctly (see fig. )  
If the earbuds do not fit your ears  
correctly, low-bass sound may not be  
heard. To enjoy better sound quality,  
change the earbuds to another size, or  
adjust the earbuds position to sit on  
your ears comfortably and fit your ears  
snugly.  
If the earbuds do not fit your ears, try  
another size. Confirm the size of the  
earbuds by checking color inside (see  
fig. -).  
When you change the earbuds, turn to  
install them firmly on the headphones  
to prevent the earbud from detaching  
and remaining in your ear.  
Precautions  
Please keep your headphones clean  
at all times especially inside the  
rubber earbud. (see fig. )  
If any dust or ear wax inside the  
earbud, you may experience some  
listening difficulties.  
How to use  
Wearing the headphones  
(see fig. )  
Wear the earpiece marked in your  
right ear and the one marked in  
your left ear.  
There is a tactile dot on the unit  
marked to distinguish the left side.  
Listening with headphones at high  
volume may affect your hearing. For  
traffic safety, do not use while  
driving or cycling.  
The earbuds may deteriorate due to  
long-term storage or use.  
How to use the cord slider  
(see fig. -)  
Move up and down to change the split  
position of the cord.  
Install the earbuds firmly onto the  
headphones. If an earbud  
accidentally detaches and is left in  
your ear, it may cause injury.  
Earbud sizes (inside color)  
Small  
SS*  
Large  
Note on static electricity  
In particularly dry air conditions, mild  
tingling may be felt on your ears. This  
is a result of static electricity  
accumulated in the body, and not a  
malfunction of the headphones.  
The effect can be minimized by  
wearing clothes made from natural  
materials.  
S
M
L
How to use the supplied  
cord adjuster  
(see fig. -)  
You can adjust the cord length by  
winding the cord on the cord adjuster.  
(The cord can be wound to the cord  
adjuster up to 50 cm. If you wind  
more, the cord comes off from the cord  
adjuster easily.)  
(Red)  
(Orange) (Green) (Light blue)  
* This size is optional and available at  
purchase.  
Sectional View  
To detach an earbud  
(see fig. -)  
While holding the headphone, twist  
and pull the earbud off.  
EP-EX10A is available (sold  
separately) as optional replacement  
earbuds.  
EP-EX10A offers 4 types of the  
earbuds: SS, S, M and L.  
Tip  
If the earbud slips and cannot be detached,  
wrap it in a dry soft cloth.  
1
2
Wind the cord.  
Colored parts  
Push cord into slot hole to  
secure in place.  
To attach an earbud  
(see fig. -)  
Note  
Push the parts inside of the earbud into  
the headphone until the projecting  
part of the headphone is fully covered.  
On copyright  
Do not wind the plug or split section of the  
cord, as it will strain the cord and may cause  
a wire break.  
iPod is a trademark of Apple Inc.,  
registered in the U.S. and other  
countries.  
Cleaning the earbuds  
Remove the earbuds from the  
headphones, and wash them with a  
mild detergent solution.  
 

Sharp Calculator ELW516XBSL User Manual
Silva GPS Receiver DGPS 200 User Manual
Silvercrest Microwave Oven SMW 800 A1 User Manual
Sony Cassette Player M 950 User Manual
Sony Headphones XBA1 User Manual
SOYO Computer Drive Lite Motherboard User Manual
Spracht Clothes Dryer CP 2016 003 User Manual
Star Trac Fitness Electronics IP L5002 User Manual
SunBriteTV CRT Television SB 5515HD User Manual
Tanaka Pole Saw TPS 260PF User Manual