4-471-977-11(1)
Head
Mounted
Display
Reference Guide
Before Initial Use
Refer to the “Startup Guide” for instructions on
connecting the system, wearing the unit, and
completing initial settings.
HMZ-T3W
Important Safety Instructions
1) Read these instructions.
The following FCC statement applies only
to the version of this model
manufactured for sale in the U.S.A. Other
versions may not comply with FCC
technical regulations.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10) Protect the power cord (mains lead) from
being walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
12) Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
If you have any questions about this
product, you may call: Sony Customer
Information Center 1-800-222-SONY
(7669) or
below is for the FCC related matters only.
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
3
Regulatory Information
Notice for customers in Canada
CAN ICES-3 B/NMB-3 B
Declaration of Conformity
Trade Name: SONY
Model No.: HMZ-T3W
Responsible Party: Sony Electronics Inc.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired
operation of the device.
Address:
16530 Via Esprillo, San
Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part15 of the FCC
Rules. Operation is subject to the following
two conditions.: (1)This device may not
cause harmful interference, and (2)this
device must accept any interference
received, including interference that may
cause undesired operation.
Notice for customers in the United
Kingdom
A molded plug complying with BS1363 is fitted
to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or BSI to
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
BS1362, (i.e., marked with
must be used.
or
mark)
If the plug supplied with this equipment has a
detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never
use the plug without the fuse cover. If you
should lose the fuse cover, please contact
your nearest Sony service station.
This transmitter must not be co-located or
operated in conjunction with any other
antenna or transmitter.
The following FCC/IC statement applies only
to the version of this model manufactured for
sale in the U.S.A. and Canada. Other versions
may not comply with FCC/IC technical
regulations.
Notice for customers: the following
information is only applicable to
equipment sold in countries applying EU
directives.
For Processor Unit
This product has been manufactured by or on
behalf of Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan. Inquiries
related to product compliance based on
European Union legislation shall be addressed
to the authorized representative, Sony
Deutschland GmbH, Hedelfinger Strasse 61,
70327 Stuttgart, Germany.
This equipment complies with FCC/IC
radiation exposure limits set forth for an
uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines in
Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy
that it deemed to comply without maximum
permissive exposure evaluation (MPE). But it is
desirable that it should be installed and
operated keeping the radiator at least 20cm or
more away from person's body (excluding
extremities: hands, wrists, feet and ankles).
For any service or guarantee matters, please
refer to the addresses provided in the
separate service or guarantee documents.
This equipment has been tested and found to
comply with the limits set out in the EMC
Directive using a connection cable shorter
than 3 meters.
For Battery Unit
This equipment complies with FCC/IC
radiation exposure limits set forth for an
uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines in
Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules.
4
Disposal of waste batteries
and electrical and electronic
equipment (applicable in the
European Union and other
European countries with
separate collection systems)
This symbol on the product, the battery or on
the packaging indicates that the product and
the battery shall not be treated as household
waste. On certain batteries this symbol might
be used in combination with a chemical
symbol. The chemical symbols for mercury
(Hg) or lead (Pb) are added if the battery
contains more than 0.0005% mercury or
0.004% lead. By ensuring these products and
batteries are disposed of correctly, you will
help prevent potentially negative
consequences for the environment and
human health which could otherwise be
caused by inappropriate waste handling. The
recycling of the materials will help to conserve
natural resources.
In case of products that for safety,
performance or data integrity reasons require
a permanent connection with an incorporated
battery, this battery should be replaced by
qualified service staff only. To ensure that the
battery and the electrical and electronic
equipment will be treated properly, hand over
these products at end-of-life to the applicable
collection point for the recycling of electrical
and electronic equipment. For all other
batteries, please view the section on how to
remove the battery from the product safely.
Hand the battery over to the applicable
collection point for the recycling of waste
batteries. For more detailed information about
recycling of this product or battery, please
contact your local Civic Office, your household
waste disposal service or the shop where you
purchased the product or battery.
5
For customers in China:
For customers in other countries/
regions:
Health Precautions
Age Limitations
Correct Use
Watching video images or playing
games by this device may affect the
health of growing children. This device
should not be used by children 15 and
under.
Use password protection feature
(page 35) of this device to restrict
children from using this device.
• Ensure that you are wearing the head
mounted unit correctly.
– For instructions on wearing the unit,
refer to the “Startup Guide.”
– To avoid watching with the screens
skewed, check screen alignment by
referring to the confirmation screen
displayed initially.
– Note that dropping the unit or
handling it roughly may skew the
screens.
• Do not touch the processor unit, the
battery unit or the AC adaptor for a long
time when it is in use. Continuous contact
of skin with the unit may cause low
temperature burn.
Watching Video with the Head Mounted
Display
• Some people may experience discomfort
(such as eye strain, fatigue, nausea, or
motion sickness) while watching video
images or playing games. Sony
recommends that all viewers take regular
breaks while watching video images or
playing games. The length and frequency
of necessary breaks will vary from person
to person. You must decide what works
best. If you experience any discomfort,
you should stop watching the video
images or playing games until the
discomfort ends; consult a doctor if you
believe necessary.
• Avoid wearing the unit in environments
where your head may shake, or while you
are walking or performing exercise,
because there is a higher possibility that
you experience discomfort.
• The head mounted unit can be adjusted
in a range of 53.0 mm – 76.7 mm (2 1/8 in.
– 3 1/8 in.) to suit the distance between
your eyes (interpupillary distance). If you
cannot use the system within this range,
refrain from using the system.
• By default, a warning message for
automatic shutdown will be displayed
after three hours of continuous viewing.
If you clear the message and continue
watching, the system will automatically
turn off after another 3 hours.
For Comfortable Viewing
Images are perceived as appearing some
distance from the viewer.
• You should also review (i) the instruction
manual of any other device or media
used with this device and (ii) our website
below for the latest information.
If you normally wear glasses or contact
lenses, wear them as usual during use
(with the exception of reading glasses).
Note that watching with bifocals may be
less than optimal.
For customers in Europe, Russia, Ukraine
and UK:
For customers in the U.S.A. and Latin
America:
For customers in Canada:
6
Installation Environment
Avoid installation in the following
environments.
• Places subject to vibration
• In direct sunlight, or where it is very hot
or humid
• Places that are extremely cold
Also avoid putting liquid-filled containers
(such as flower vases) on top of the
processor unit or the battery unit, or using
the system where it may be splashed. The
system may be damaged if splashed with
water.
Precautions
Power Supply
Position the AC adaptor near the wall
outlet (mains) used. In case of strange
noises, fumes, or smoke from the system,
immediately unplug the AC power cord
(mains lead) to turn all power off. Only
pressing the power button on the head
mounted unit or the processor unit will not
turn the system off completely.
Transport
Do not move the product pulling it by the
cable or the headband. The product may
fall or crash, causing damage to the
product.
AC Adaptor
• Do not use any unspecified adaptor. It
may cause failure of the product.
• Performance and safety are not
guaranteed if any other USB cable or AC
power cord (mains lead) than those
exclusive to this system is used.
Condensation
Condensation occurs when moisture in the
air condenses on metal panels or other
parts, forming droplets. Condensation may
form on outer surfaces or internally if the
system is suddenly moved from a cold to a
warm environment, or when a heater is
turned on in a cold room where the system
is installed. If condensation forms, do not
use the system until the droplets
evaporate.
• Do not disassemble or modify the AC
adaptor.
• Do not touch metal parts of the AC
adaptor. Especially keep in mind that
touching it with a metal tool may cause a
short-circuit, damaging the AC adaptor.
• Operations are not guaranteed if any USB
hub or USB extension cable is used. Be
sure to use the exclusive USB cable
supplied with the system and follow the
connecting instructions specified by the
device to be connected.
• If the system is not plugged into a wall
outlet (mains)
Leave the system unplugged, and wait
until the droplets evaporate.
• If the system is not on
Leave the system off, and wait until the
droplets evaporate.
• If the system is on
Leave the system on, and wait until the
droplets evaporate.
Built-in Battery
• It is recommended to replace the battery
if the operation time with the battery fully
charged becomes almost half that with
initial use. Consult your nearest Sony
service center.
• The completely discharged battery can
be recharged normally 500 times. The
number of times varies depending on the
conditions of use.
Using the system when condensation has
formed may damage it.
Static Electricity
You may feel a tingling sensation in your
ears in dry seasons. It does not indicate
that the system is damaged, but is due to
static electricity accumulated in your body.
The influence of static electricity may be
reduced by wearing clothes made of
• If the product will not be used for an
extended period, recharge the battery
every six months to eliminate battery
degradation.
7
natural materials that generate less static
electricity.
Packaging Materials
Keep the original box and protective
cushioning for future use, in case you
move or need to ship the system for repair
or other reasons.
Lens Care
• Handle the lenses on the head mounted
unit carefully to avoid smears or
scratches. If the lenses become dirty,
wipe them gently with a soft lens-
cleaning cloth.
HDMI Jacks and Connectors
Take these precautions to avoid damaging
HDMI jacks and connectors.
• Do not use liquid solutions, such as lens-
cleaning fluid, water, or alcohol-based
cleaners.
• Do not impart excessive shock or force to
the lenses. A chipped or cracked lens
could cause injury. If the lens is chipped
or cracked, stop using the system
immediately and do not touch the
damaged part.
• When inserting cables, note the shape
and orientation of the connector and the
HDMI jack on the battery unit or the
processor unit.
HDMI input and output
Cleaning the System
The connector is upside-down
HDMI input and output
Clean outer surfaces of the system using a
soft cloth lightly moistened with a mild
detergent. Do not use solvents, such as
thinner, benzine, or alcohol, which may
damage surfaces.
Headphone Care
The connector is not straight
• A dirty headphone plug may cause static
or skipping. To ensure optimal sound,
clean the plug with a soft cloth
occasionally.
• Before moving the processor unit, always
disconnect the HDMI cable.
• Also clean the earbuds. Remove the
earbuds from the headphones and hand-
wash them using a mild detergent. After
washing, dry the earbuds thoroughly
before use.
• When connecting or disconnecting HDMI
cables, hold the connector straight. Do
not hold the connector at an angle or
force it into the HDMI jack.
• Use either the supplied HDMI cable or a
commercially available High-Speed HDMI
cable.
Extended Listening at High Volume
Listening at high volume over extended
periods may harm hearing. To protect your
hearing, avoid listening at excessive
volume.
Headphone Handling
Initial Volume
• If you experience an allergic reaction to
the supplied headphones, stop using
them at once and contact a doctor.
To avoid sudden loud output, keep the
initial volume low. Increase the volume
gradually until the desired level is reached.
• When you unplug the headphones from
the head mounted unit or the processor
unit, make sure to hold the headphone
8
plug to unplug it. Pulling by the
headphone cord itself may damage it.
• Earbuds may deteriorate after extended
use or storage.
Restrictions on use on wireless
communication function in countries/
regions
• In the U.S.A, Canada, Puerto Rico,
Mexico, Australia, and Turkey, wireless
communication is restricted in indoor
use. Wireless communication in outdoor
use is inhibited by the law, and illegal
operation is punished.
• The wireless communication function of
this system is only used in the countries
below. Use in other countries may be
against the law of the country and be
punished.
Wireless Communication
• Although this system is equipped with an
encryption function for its wireless
communication, pay high attention to
possible interception. Do not use the
system for sending/receiving sensitive
data or intelligence or for any usage fatal
to human life.
• Interception means that a third party
intentionally or inadvertently obtains the
content of wireless communication with
a receiver.
• This system uses the 60 GHz frequency
band for wireless communication. This
band may be used by other wireless
communication devices. To prevent
signal interference between this system
and those devices, note the following:
The 60 GHz frequency band used by this
system employs the OFDM system for
modulation.
• If 3 or more pairs of 60 GHz band wireless
devices including this product are
activated in an area of 20 meters (66 feet)
square, wireless communication may be
disabled by signal interference.
For customers using the HMZ-T3W sold in
the U.S.A., Canada, or Puerto Rico
The wireless communication function of
this system is only used in U.S.A., Canada,
and Pureto Rico.
For customers using the HMZ-T3W sold in
the EU or other European countries,
Turkey, Australia, or New Zealand
The wireless communication function of
this system is only used in the following
countries: Germany, France, Italy, Spain,
Switzerland, Portugal, Austria, Greece,
the Netherlands, Belgium, Luxembourg,
Denmark, Sweden, Norway, Finland,
Poland, Hungary, Romania, the Czech
Republic, Turkey, Bulgaria, the United
Kingdom, Australia, and New Zealand.
• Keep the wireless communication
function of this system turned off in an
aircraft.
For customers using the HMZ-T3W sold in
other countries
The wireless communication function of
this system is only used in the country
where you purchased the system.
9
Contents
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
10
• HDMI cable (1)
Supplied Accessories
Make sure the following items are
included with the system after
purchase. If any items are missing,
contact your Sony dealer or a local
authorized Sony service center.
• Light blocker (Bottom) (1)
For installation of the supplied
accessories, refer to the “Startup
Guide.”
• AC power cord (mains lead) (2)
Use the supplied AC power cord
(mains lead) only with this system,
not with other electronics.
• Connecting cord holder (1)
• Headphones (1)
• AC adaptor (large) (AC-L200D) (1)
• Earbuds (1 set)
• AC adaptor (small) (AC-UD10) (1)
• Micro USB cable (for AC-UD10) (1)
Medium-sized earbuds are initially
attached, at the time of purchase.
• Carrying case (1)
• Stand (1)
• Reference Guide (this guide)
• Startup Guide
11
Parts and Controls
For connection and wearing of the system, refer to the “Startup Guide.”
Head Mounted Unit
Top headband adjuster
Top headband strap
Forehead supporter
Bottom headband
strap
Bottom headband adjuster
Attachment sensor
Do not block the sensor hole.
VOL +/– buttons
(Power On/Standby)
button
Press and hold the button for
more than one second to turn
the system power on/off.
Lens span adjusters
Control buttons (///,
MENU*)
*
The MENU button serves two purposes. Press the MENU button to view setting menus as well
as to confirm setting changes (when it functions as an Enter button).
RELEASE (Forehead
supporter release) lever
(Headphone) jack*
Lenses
*
Either the supplied headphones or your own stereo mini-plug headphones can be connected.
Note
• The cord connecting the head mounted unit and the battery unit cannot be
disconnected.
12
Battery Unit (Front)
Ventilation slot (top)
Ventilation slot
(rear)
(Power) indicator
HDMI IN/MHL jack
Micro USB jack
WIRELESS (Wireless
Link) indicator
Processor Unit (Front/Top)
/ (Power On/Standby) button
INPUT button
POWER indicator
(Headphone) jack
PASS THROUGH indicator
HDMI INPUT 1/2/3 indicators
HDMI OUT (HMD) jack
WIRELESS (Wireless link)
indicator
Processor Unit (Rear)
HDMI IN 1/2/3 jacks
HDMI OUT (TV) jack
DC IN 8.4V jack
13
Indicators
The indicators on the battery unit and processor unit show the statuses of this
system.
Indication
Status
Battery Unit
(Power) indicator
Lit in green
Power On (not charging)
Power On or Off (during charging)
Power Off (not charging)
Wireless link established
Lit in orange
Unlit
WIRELESS (Wireless
link) indicator
Lit in blue
Fast flashing in blue Wireless link established (with no
video input to the selected input
jack)
Flashing in blue
Unlit
Establishing Wireless link
Wireless link off
Processor Unit
POWER (Power)
indicator
Lit in green
Lit in red
Unlit
Power On
Standby with Power Off
Power unconnected
PASS THROUGH
indicator
Lit in orange
Power Off (Standby) with “HDMI
pass-through” set at “On”
Unlit
In cases other than the
mentioned above
HDMI INPUT 1/2/3
indicators
Lit in orange
Unlit
The indicator for the selected
HDMI input lights.
Standby with “HDMI pass-
through” set at “Off”
WIRELESS (Wireless
link) indicator
Lit in blue
Wireless link established
Fast flashing in blue Wireless link established (with no
video input to the selected input
jack)
Flashing in blue
Unlit
Establishing Wireless link
Wireless link off
For alerts by the indicators, see “Warning by the indicator” in “Troubleshooting”
14
Charging time and operating time
The charging time and the operating
time are as follows at room
Charging the Battery
temperature of 23 °C (74 °F).
When the system is to be used for the
first time or the battery is exhausted,
recharge the battery.
For details on charging, refer to the
“Startup Guide.”
Charging
time
Approx. 5.5 hours (in
wired operation)
Approx. 4.5 hours (in
standby mode)
Operating Approx. 3 hours (in
Connect the AC-UD10 AC adaptor
(small) and the AC power cord to the
battery unit to start charging.
The (power) indicator is lit in orange
during charging, and the indicator
goes dark when charging is
completed (if the system power was
off).
time
wireless operation)
Approx. 7 hours (in
wired operation)
Approx. 3 hours (in
MHL operation)
Notes
• The charging time and operating time
may differ, depending on ambient
temperature, the battery condition and
other conditions of use.
• Longer charging time is required or
charging is not completed in the
following cases:
Tip
• Charging is possible even while the
system is turned on, but longer charging
time is required. We recommend
charging with the system turned off
when the system is not to be used.
– when the system is used in wireless
communication mode
– when equipment is connected to the
battery unit and operated in MHL
connection
– under high ambient temperatures
• The operating time is shorter when
wireless communication conditions are
poor.
Notes
• Charging may not be possible or longer
charging time may be required
depending on ambient temperature or
other conditions of use.
– Perform charging under temperatures
from 5 °C to 35 °C (41 °F to 95 °F).
– Charging may not be performed in
wireless communication mode. In this
case, turn off the system power, or try
charging in wired communication
mode.
• The battery unit and the AC adaptor
become warm when the system is in use
or while charging. This is not a problem
for safety.
If the battery unit or the AC adaptor is
excessively hot, stop using the system
and turn off the system power.
Checking the remaining battery capacity
Press the MENU button on the head
mounted unit to display the menu
then select “Information.”
The remaining battery capacity
appears on the top right of the
Information screen (page 28).
Remaining battery indicator
Fully charged
Battery exhausted
15
Using in Wireless Communication
Connect the processor unit and the battery unit wirelessly.
Installation Examples and Communication Distance
The processor unit and the battery unit of this system each has an antenna for
wireless communication on the side with the SONY logo. When wirelessly
connecting the processor unit and the battery unit, install them referring to the
following installation examples.
The gray portions in the following diagrams indicate the areas in which wireless
communication is possible.
Flat placement
Top view
Placement with the Supplied
Stand
Top view
Approx. 2.5 m (8.2 feet)
Approx. 3.5 m (11.5 feet)
SONY logo
Approx. 5 m (16.4 feet)
Approx. 7 m (23 feet)
SONY logo
Approx. 2.5 m (8.2 feet)
Side view
Approx. 3.5 m (11.5 feet)
Side view
Ceiling
Face the SONY logo side
toward the battery unit.
Face the SONY logo
side toward the
processor unit.
Radio wave
Radio wave
Approx. 5 m (16.4 feet)
With the
SONY logo
side upward
Approx. 7 m (23 feet)
Tip
• When the battery unit is placed flat on a horizontal surface, wireless communication is
achieved mainly through radio waves reflected off the ceiling or walls. If the
communication distance is shortened due to your room environment, use the supplied
stand for a longer communication distance.
16
Using the Stand
Checking the Strength of Radio
Waves
Press the MENU button on the head
mounted unit to display the menu,
then select “Information.” The
strength of radio waves appears on
the top right of the Information screen
1 Fix the supplied stand to the
battery unit.
Insert the projection of the stand into
the hole on the bottom of the battery
unit.
Strength of radio waves
Level of radio wave strength
4
3
2
1
0
Strong
Weak
2 Place the battery unit facing the
SONY logo side toward the
processor unit.
To maintain stable connection, use
the system where radio waves are as
strong as possible. The recommended
level of radio wave strength is 2 or
higher as a guide.
SONY logo
Processor unit
Notes on Wireless Communication
• The system cannot achieve wireless
communication if there is an obstruction
between the processor unit and the
battery unit (e.g. room-to-room
communication).
• In the following cases, the status of
wireless communication between the
processor unit and battery unit is
adversely affected, decreasing the
possible communication distance and
generating disturbances in video and/or
audio (picture degradation, signal
interruption, noise, etc.).
After using
Remove the stand from the battery
unit and hook it on the cable of the
battery unit.
– When the system is used in a room of
reinforced concrete or stone walls or
floor, or with floor heating activated
– When there is some obstruction, such
as a partition, door, fireproof glass,
furniture with metal materials, or an
electric appliance, between the
processor unit and the battery unit
17
– When the processor unit or battery unit
is installed in a rack with a door or in a
metal rack
– When the processor unit and the
battery unit are installed in the same
rack
Using in Wired
Communication
• In the following cases, the condition of
wireless communication is temporarily
degraded owing to a change in the
environment, causing disturbance in
video and audio or affecting operations
of the system.
Connect the processor unit and the
battery unit, using an HDMI cable.
Processor unit (Front)
– If the panel with the SONY logo of the
processor unit or the battery unit is
blocked by a human body or some
object
– If a person, animal, or object (e.g.
curtain, door, or partition) in the room
moves
HDMI cable*
HDMI IN/
MHL
• If video and audio are disturbed, check
the locations and directions of the
processor unit and battery unit.
• Wireless communication is enabled only
between the processor unit and battery
unit purchased in combination.
• Only two sets of units, including this
system, can be used in the same single
room.
Battery unit
*
Use a High-Speed HDMI cable sold
separately.
18
Using the Carrying Case
You can pack the system in the
supplied carrying case. Put the battery
unit in the pocket and fix the head
mounted unit with the hook and loop
fastener.
Using with a Portable
Device
The system can be used by connecting
the battery unit directly to playback
equipment using an HDMI cable.
With this connection, you can use the
system where there is no AC power
supply.
Head mounted unit
Battery unit
An MHL device can be connected
using the MHL cable (sold separately).
Smartphone, etc.
Connecting cable*
HDMI IN/
MHL
Battery unit
*
For connecting an MHL device, use the
MHL cable (sold separately), or for
connecting other playback equipment,
use the supplied HDMI cable.
Notes
• When using the system in an aircraft or
any other place where radio wave
transmission is prohibited, be sure to set
“Wireless Connection” in “General Setup”
to “Off” (page 37).
• With this connection method excluding
the processor unit, some setting items in
available and you cannot use those
functions.
19
Fitting the Head Mounted Unit
The head mounted unit can be adjusted in several ways to ensure a personalized,
comfortable fit. For a more comfortable fit, always adjust the head mounted unit
before putting it on.
When fitting the head mounted unit for the first time after purchase, refer to the
“Startup Guide.”
Adjusting the forehead supporter
The forehead supporter can be
adjusted back and forth or up and
down.
To adjust up and down
To adjust back and forth
Move the forehead supporter up and down.
Tip
• Adjust the position of the forehead
supporter forward or downward if the
head mounted unit contacts your glasses
or nose.
To move the forehead supporter back and forth,
slide the RELEASE (forehead supporter release)
lever toward the right, then move the forehead
supporter.
20
Light blocker
Attaching the connecting cord holder
To keep the connecting cords of the
head mounted unit out of the way,
use the supplied connecting cord
holder and attach the connecting cord
to the bottom headband.
The top light blockers are detachable.
If external light reflected on the
screens is distracting, attach the light
blockers.
“L” Light blocker (Top)
Connecting
cord holder
“R” Light blocker (Top)
The upper-left light blocker is labeled “L,” and
the upper-right one, “R.” Attach the correct top
light blocker on each side by pushing the tabs
into the three holes on the top of the lens
section.
Light blocker (Bottom)
To attach the bottom light blocker, push the
tabs into the 8 holes on the bottom and side of
the lens, and hook on the right and left ends.
Notes
• It may not be possible to attach the light
blockers when wearing some sorts of
glasses.
• If external light is still distracting with the
light blockers on, dim the room lights or
move away from external light.
21
you pull the right end of the strap out
a little.
For a Comfortable Fit
To tighten, simply push the right end
of the strap in a little.
Have the weight of the head mounted unit
balanced between your forehead and the
back of your head
To adjust the straps on the left
Forehead
supporter
To loosen
To tighten
To loosen, hold down the fastener
button on the bottom of the
Bottom headband
headband adjuster as you pull the left
end of the strap out a little.
To tighten, hold down the fastener
button on the bottom of the
headband adjuster and push the left
end of the strap in a little.
Wear the head mounted unit so that it
feels balanced between the forehead
supporter and bottom headband, and
after repositioning it to bring the
lenses in front of your eyes, make sure
it fits securely.
Note
Be sure to leave a space between the
bridge of the head mounted unit
(between the lenses) and your face, so
that the unit does not touch your
nose.
• The circles on the headband adjusters are
the caps for the accessory fixing screw
holes for future use. They are not buttons
and are inoperative when pressed.
Ensure a secure fit
If either headband is too loose or too
tight, adjust the strap length for a
better fit.
To adjust the straps on the right
To loosen
To tighten
To loosen, hold down the fastener
button on the headband adjuster as
22
To attach an earbud
Attaching and Replacing
Earbuds
Bass may be inaudible unless earbuds
fit well. For a better listening
Push the parts inside of the earbud into the
headphone until the projecting part of the
headphone is fully covered.
experience, try a different earbud size
or adjust the position of the earbuds,
so that they fit perfectly in your ears.
Medium-sized earbuds are initially
attached to the headphones, at the
time of purchase. If the earbuds feel
uncomfortable, try replacing them
with the supplied large or small
earbuds. Earbud sizes are color-coded
and can be identified by the color
inside.
About noise isolation earbuds
Supplied noise isolation earbuds
provide a snug fit for effective
attenuation of ambient noise.
To avoid having the earbuds come off
in your ear, be sure to attach earbuds
securely to the headphones when
replacing them.
Pressure-relieving
urethane cushion
S (Orange) M (Green) L (Light blue)
Earbud sizes (inside color)
Colored parts
Notes
• Prolonged use of snugly fitting earbuds
may strain your ears. If you experience
discomfort, discontinue use.
• The pressure-relieving urethane cushion
is extremely soft. If it breaks or detaches
from the earbuds, it will not take its
correct position and the earbuds will lose
their noise isolation function.
Small
Large
SS
(Red)
S
M
L
(Orange) (Green) (Light
blue)
• The urethane cushion may deteriorate
over time. If the pressure-relieving power
is lost and the urethane cushion hardens,
the earbuds may lose their noise isolation
function.
To detach an earbud
While holding the headphone securely,
twist the earbud as you pull it off.
• Do not wash the earbuds. Keep them dry,
otherwise they may deteriorate quickly.
Replacing Consumables
The following replacement parts are
available.
• Earbuds*
• Light blocker (Top) (1 each for the left
and right)
Tip
• If the earbud slips in your fingers and
remains attached, try holding it with a dry
cloth for a better grip.
• Light blocker (Bottom)
23
• Connecting cord holder
• Forehead supporter cushion
• Headband adjuster cushion
• Stand
When these consumables break or
show signs of wear, consult your
nearest Sony dealer or Sony service
center.
*
Optional replacement earbuds can be
ordered from your nearest Sony dealer.
Replacing the forehead supporter cushion
or headband adjuster cushion
The cushion is attached with double-
back tape. To replace the cushion,
peel off the old cushion from the
forehead supporter or the headband
adjuster then put a new cushion in the
same place.
Forehead supporter cushion
Headband adjuster cushion
24
Confirming Screen Alignment
Confirm screen alignment by referring to the confirmation screen displayed
initially after lens span adjustment. Screens on the head mounted unit are
described below, with an explanation of how to confirm alignment.
The display section of the head mounted unit consists of two small screens, on the
left and right. Images on each screen overlap to form a single image.
Always check screen alignment by referring to the confirmation screen before use
to make sure the screens are aligned properly.
Left image
Right image
Image perceived with both eyes
25
Correct Display
For correct display, slide the lens span adjusters as needed so that all three “”
marks and the horizontal line intersect.
It is acceptable if the “” marks and the horizontal line intersect in a position other
than the center of the screen.
Incorrect Display
If even one of the “” marks and the horizontal line do not intersect, recheck if you
are wearing the head mounted unit correctly, referring to the “Startup Guide.” If
they still do not intersect, stop using the system. as the head mounted unit may
have been bent out of shape, or it may be damaged. If this condition occurs,
contact your nearest Sony dealer or local authorized Sony service center.
“” marks and the horizontal
line do not intersect.
The horizontal line appears to
be extremely slanted.
The middle “” mark does not
intersect the horizontal line.
26
Note
• After 90 seconds of inactivity, the setting
menu will automatically close.
System Settings
Tips
Setting menus can be accessed at any
time to change or adjust a variety of
system settings, such as video picture
quality, audio output format, and 3D
display format. To view the menus,
press the MENU button on the head
mounted unit.
• To return to the previous menu, press the
button.
• To exit the setting menu, press the
button in the setting category menu.
Basic Menu Operations
1 Press the MENU button on the
head mounted unit.
2 Press the / button to select the
desired setting category, and then
press the MENU button.
3 Press the / button to select the
desired menu, and then press the
MENU button.
4 Press the /// button to
change or adjust settings as
needed, and then press the MENU
button to enter your changes.
27
Menus
Default settings are underlined.
Information
Identifies input signals (video and audio signals) from equipment connected to the
system and shows various types of information. “Unsupported signal” indicates
that the input signal is incompatible with the system, and “No signal” is shown
when no signals are input.
AC power operation
Input video signal
External input
Input audio signal
Lens span adjustment
Lens span
adjustment
Adjusts the lens span of the head mounted unit to
match the distance between your eyes (interpupillary
distance), for an optimal viewing experience. Use the
lens span adjusters on the head mounted unit for
adjustment. For details, refer to the “Startup Guide.”
Notes
• Without the lens span adjusted correctly, you cannot enjoy
an optimal viewing experience. Always adjust the lens span
before use.
• Audio is muted during adjustment.
• The volume cannot be changed during adjustment.
28
3D Settings
Reset
Resets all “3D Settings” items to the original default
values.
3D Display
Manually select the display format for 3D content.
Available settings vary depending on whether the
source signal includes a 3D format identification signal,
as follows.
Example of 3D display
For 3D content without a 3D format identification
signal
Side-by-Side: Select for side-by-side 3D content, with
similar images displayed side by side.
Off: Select to display content in 2D format.
Over-Under: Select for top-and-bottom 3D content,
with similar images displayed on top and bottom.
For 3D content with a 3D format identification signal
On: Select to display content in 3D format.
Off: Select to display content in 2D format.
Notes
• If 3D content is not displayed correctly using the selected
settings, try changing “Side-by-Side” to “Over-Under” or
vice-versa.
• When selecting “Side-by-Side” or “Over-Under,” change the
setting to “Off” after viewing 3D content.
29
Auto 3D
On: Automatically switches to 3D display mode when a
3D format identification signal is detected. If the
3D format identification signal is no longer
detected, the system will automatically switch to
2D display mode.
Off: Deactivates this function.
Note
• If images do not appear in 3D when “Auto 3D” is set to “On,”
try changing the “3D Display” setting.
Display
Picture Mode
Vivid: Vivid colors and sharp contrast, for concerts,
sports, and other televised content.
Standard: Emphasizes a natural picture. Standard
picture quality for a variety of video sources.
Cinema: Picture quality designed especially for
cinematic content.
Custom1/Custom2: Stores your customized preferred
picture quality, adjusting from original flat picture.
Game1: Picture quality designed for games.
Game2: Picture quality for improving visibility of dim
scenes of games.
Details of the “Picture
Mode” option you
choose here can be
adjusted in the settings
from “Reset” to
“Contrast Remaster”
below.
Game3: Picture quality for improving visibility of dark
scenes of games.
Game4: Picture quality for improving visibility of
extremely dark scenes of games.
Note
• When “Picture Mode” is set to “Game1” to “Game4,” you can
switch over among these modes by pressing , , , or
(page 12) during viewing. This operation is not available
when the setting menu is displayed.
Reset
Restores all the values (except for values of “Display
Size,” “Screen,” “24p True Cinema,” “Cinema
Conversion,” “Overscan,” and “Wide Mode” in “Display”)
of the selected mode in the “Picture Mode” menu to the
default settings when selecting “Yes.”
Picture
Brightness
Color
Adjusts image contrast.
Adjusts the brightness of the image.
Adjusts the color intensity of the image.
30
Color
Temperature
Adjusts image color temperature.
Natural: Automatically optimizes color temperature for
each “Picture Mode,” based on characteristics of
human vision.
Cool: Cool blue color tones.
Medium: Color tones between “Cool” and “Warm 1/
Warm 2.”
Warm 1/Warm 2: Warm red color tones. “Warm 2” is
redder than “Warm 1.”
Panel Drive Mode Select the type of display method for image motion.
Normal: Standard image appearance.
Clear: Reduces blurring of fast-moving images.
Notes
• Although selecting “Clear” reduces blurring of fast-moving
images, it also darkens the screen as a whole. If this is
distracting, select “Normal.”
• The screen as a whole may appear to flicker, depending on
the source signal. If this is distracting, select “Normal.”
Clear Black
Adjusts the appearance of dark image areas to fit the
selected “Picture Mode.”
Sharpness-Hi
Sharpness-Mid
Noise Reduction
Controls thin edges and fine texture of images to make
the images stand out or softer.
Controls thick edges and rough texture of images to
make the images stand out or softer.
Reduces random image noise, similar to static.
High/Medium/Low: Select the level of this effect.
Off: Deactivates this function.
Contrast
Remaster
Automatically optimizes black and white levels, for
good contrast without faded blacks or whites.
High/Medium/Low: Select the level of this effect.
Off: Deactivates this function.
Display Size
Selects the image display size.
100%: Displays the image in full-screen.
90%/80%/70%: The display size is reduced to 90%,
80%, or 70%, respectively.
Screen
Normal: Displays the original image.
Not available during 3D
playback.
The setting returns to
“Normal” if you perform
an adjustment using
the “Lens span
Theater1: Outputs the image simulated as in a theater,
viewed thorough a curved screen.
Theater2: Outputs the image simulated as in a theater
with a CinemaScope screen more than “Theater1.”
adjustment” menu
31
24p True Cinema
On: Displays 24 fps video faithfully at 24 fps. Cinematic
content of this kind is available on Blu-ray disc.
Provides a viewing experience similar to that in
theaters.
Off: Deactivates this function. 24 fps video signals are
displayed after upconversion to 60 fps.
Note
• When “Panel Drive Mode” is set to “Clear,” the screen may
appear to flicker (depending on the source signal), which
may be distracting. In such a case, either deactivate this
function or set “Panel Drive Mode” to “Normal.”
Cinema Conversion
Auto: The system automatically detects whether you
are watching video content (such as TV dramas
and animation) or film content (movies) and
switches to the corresponding conversion
method.
Video: The system always displays in a format for video
content, whether playing video or film content.
Overscan
Adjusts the display area.
On: Hides image edges. Select in case of issues such as
noise at images edges.
Not available during 3D
playback.
Off: Displays the entire image.
Wide Mode
Not available during 3D
playback.
Normal: Displays the images at the original 4:3 aspect
ratio.
Full: Displays 4:3 content in full-screen, stretching the
images horizontally. 16:9 content is also displayed
full-screen, at the original aspect ratio.
Zoom: Enlarges the images vertically and horizontally,
preserving the original aspect ratio.
Note
• “Normal” is not available with HD input sources (1080i, 720p,
or 1080p).
32
Sound
Note
• The Sound menu items (except “A/V SYNC”) are available only when the processor unit is
connected.
Reset
Resets all “Sound” settings to the original default
values.
Surround
Standard: Standard acoustic setting, providing a
spacious sound stage for a range of content.
Cinema: Emphasizes a natural sound stage rivaling the
impressive acoustics of movie theaters, especially
for spoken dialog. Immersive, with each channel
blended naturally. A good choice for movies.
Game: Ideal for games. Provides pinpoint sound
localization, for a clear sense of where sounds
originate. For immersive gameplay in games with
multi-channel surround-sound effects. Especially
suitable for games that have a multi-channel
soundtrack.
Music: Emphasizes detail and purity of source audio.
Faithful reproduction, similar to monitor
equipment at recording studios. A good choice for
music.
Off: Deactivates surround-sound effects.
Note
• Volume may vary depending on the source audio signal and
selected surround-sound mode.
Dolby Pro Logic IIx
Selects matrix decoder operation. You can easily enjoy
surround effects even when the input signal is in 2
channels, by simply activating the matrix decoder.
Movie: Performs Movie-mode processing of Dolby Pro
Logic IIx. Suitable for playing movie music with
Dolby Surround encoded. Movies dubbed in
another language or videos of old movies can be
played in 7.1-channel mode.
Music: Performs Music-mode processing of Dolby Pro
Logic IIx. Suitable for normal stereo sound sources
such as CDs.
Off: Deactivates the matrix decoder.
Note
• “Dolby Pro Logic IIx” is fixed to “Off” if the “DTS Neo:6”
setting is not “Off.”
33
DTS Neo:6
Selects matrix decoder operation. You can easily enjoy
surround effects even when the input signal is in 2
channels, simply activating the matrix decoder.
Cinema: Performs Cinema-mode processing of DTS
Neo:6.
Music: Performs Music-mode processing of DTS Neo:6.
Off: Deactivates the matrix decoder.
Note
• “DTS Neo:6” is fixed at “Off” if the “Dolby Pro Logic IIx”
setting is not “Off.”
Treble
Bass
Adjusts high-frequency audio output.
Adjusts low-frequency audio output.
Harmonics Equalizer On: Retrieves the tail shape of the waveform which
would likely be omitted by audio compression
algorithms due to its low amplitude.
Off: Deactivates this function.
A/V SYNC
Corrects out-of-sync audio and video signals by
delaying audio output. Audio output can be delayed in
10-millisecond increments, in a range of 0-100 ms.
Note
• Some out-of-sync audio and video cannot be corrected with
this function, depending on the source signal.
Type of
Headphones
Switches to the optimal virtual surround-sound setting
for the type of headphones used.
Inner Ear: Ideal for headphones worn in your ears, such
as the supplied headphones.
Overhead: Ideal for headphones worn over or on your
ears.
Note
• Surround-sound effects may not be produced correctly
unless this setting matches the type of headphones used.
Dual Mono
Switches the main or sub audio output for audio source
signals other than linear PCM.
Main: Both left and right headphone output consists
solely of the main audio content.
Sub: Both left and right headphone output consists
solely of the sub audio content.
Available only with dual
mono audio source
signals.
Not available for linear
PCM source signals.
Main/Sub: Headphone output on one side consists of
the main audio content. Output on the other side
consists of the sub audio content.
34
General Setup
Set password
A password can be set to restrict use of the system.
Once a password is specified, it must be entered each
time the system is turned on.
To cancel password protection, select “Cancel
password” and enter the password.
Cancel password
“Set password” is not
available when a
password has been set.
“Cancel password” is
not available when no
password has been set.
Note
• The system automatically turns off in the following
situations. Either turn the system on and enter the password
again or cancel password protection.
– When the password is entered incorrectly, and you close
the displayed setting menu by using the button
– After 90 seconds of inactivity on the password input screen
Input
Selects the input to the processor unit. The signal input
to the selected input jack is displayed on the head
mounted unit.
HDMI1: Input via the HDMI IN 1 jack
HDMI2: Input via the HDMI IN 2 jack
HDMI3: Input via the HDMI IN 3 jack
Not available when the
processor unit is
disconnected.
HDMI Dynamic
Range
Selects the video signal input level.
Auto: The system automatically detects the input level.
Normally set to “Auto.”
Full: Select this option when the highlights in the image
are blown out or the shadows are blocked.
Limited: Select this option when the highlights in the
image are dull or the shadows are outstanding.
HDMI pass-through
Not available when the
processor unit is
On: Activates pass-through, enabling you to watch or
listen to content on a TV or other display device
when the system is in standby mode. For details,
refer to the “Startup Guide.”
disconnected.
Off: Deactivates this function. To save power, select
“Off” when a TV or other display device is not
connected to the processor unit.
35
Control for HDMI
On: Activates control for HDMI CEC (Consumer
Electronic Control)-compatible equipment
connected to the system using the ///
button: Starts playback.
button: Pauses playback.
button: Jumps to the previous chapter. Hold the
button down for fast-rewind.
button: Jumps to the next chapter. Hold the
button down for fast-forward.
Off: Deactivates this function. Use the remote control of
the connected equipment to control it.
Notes
• If control is not possible with this setting activated, the
connected equipment is not compatible with the system’s
“Control for HDMI” function. Control connected equipment
directly.
• The connected equipment cannot be controlled when
“Picture Mode” is set to “Game1,” “Game2,” “Game3,” or
Power off when
unmounted
On: Turns the system off automatically 20 minutes after
you take the head mounted unit off.
Off: Deactivates this function.
Tip
• Regardless of this setting, the screens will go off
automatically 10 seconds after you remove the head
mounted unit.
No signal Standby
Language setting
On: Turns the system off automatically when 30
minutes elapse without signal input.
Off: Deactivates this function.
Sets the language used for menus and other interface
elements.
Notes
• Audio is muted while this setting is configured.
• The volume cannot be adjusted while this setting is
configured.
Menu Display
3D: Displays the menu in 3D format.
2D: Deactivates the 3D format of the menu display.
36
Prolonged viewing
warning
On: Activates automatic display of a warning about
whether to turn the power off after 3 hours of
continuous viewing. Selecting “Yes” on the
warning screen will turn the power off. Selecting
“No” will cause the power to be turned off 3 hours
later, after 6 hours of continuous viewing.
Off: Deactivates this function.
Note
• When the warning is displayed after 3 hours of viewing, if no
response is made in 90 seconds, the power will automatically
be turned off.
Startup viewer
warning
On: Activates automatic display of a startup warning.
Off: Deactivates this function.
Wireless Connection On: Turns on wireless connection of the battery unit.
Off: Turns off wireless connection of the battery unit.
Wireless Standby
Not available when the
processor unit is
On: When the system is in standby mode, the processor
unit starts up in synchronization with starting up
the head mounted unit in wireless operation.
Off: Deactivates this function. This mode reduces
power consumption.
disconnected.
Reset to factory
settings
Resets all settings to the original default values.
Note
• The password set in “Set password” (in “General Setup”) will
also be cleared.
37
Troubleshooting
If the following symptoms occur when using the system, check the cause and
action before requesting service. If the issue persists, contact your Sony dealer or
local authorized Sony service center.
For the troubles with video or audio, see through the multiple sections below.
Troubles with video
•
Frequently Asked Question, Audio/Video (in
common), Video, or Wireless
Troubles with audio
•
Frequently Asked Question, Audio/Video (in
common), Audio, or Wireless
Frequently Asked Question
FAQ
No video or audio. No 3D image.
1 Turn the power of this system on.
2 Turn off the playback equipment, and turn it on again.
• When PlayStation 3 is used with this system, turn off the PlayStation 3, and then
®
®
turn it on again by pressing its power button for at least 5 seconds until you hear a
beep sound twice. (If the PlayStation 3 is connected via an AV amplifier, also turn
off the amplifier and turn it on again.)
®
Troubles with 3D display
The same image is displayed side by side or top and bottom.
The 3D display format setting may be incorrect. Try changing the“3D Display”
The image is not shown in 3D.
Check the settings on the playback equipment. Refer also the Operation
Manual of that equipment.
FAQ
Video or audio of the playback equipment cannot be viewed on the TV
connected via the HDMI OUT (TV) jack of the processor unit.
1 Make sure that the “HDMI pass-through” setting in “General Setup” is set to
2 Turn off the power of this system then set it to standby mode.
• The HDMI pass-through function is enabled only when the “HDMI pass-through”
setting is set to “On,” then the system is turned off.
• Simultaneous viewing on this system and the TV is not possible.
3 Turn off the playback equipment, and turn it on again.
• If the playback equipment is a PlayStation 3, hold down the power button on the
®
PlayStation 3 for at least 5 seconds until you hear a beep sound twice to turn it on
®
again.
38
FAQ
The “” marks and the horizontal line do not intersect on the confirmation
screen that appears when the system is turned on.
1 Adjust the length and position of the headbands, referring to “For a
Comfortable Fit” and “2 Adjust and Wear” in the “Startup Guide.”
2 Adjust the lens span while checking the display. Refer to “3 Setup and View”
in the “Startup Guide.”
• If no “” mark intersects with the horizontal line after performing actions 1 and 2,
Power Supply
Symptom
Cause/Action
The system does not turn
on
Confirm that the AC adaptor is connected properly,
referring to the “Startup Guide.”
Hold down the (Power On/Standby) button on the
head mounted unit for at least one second.
The system does not go
off
Hold down the (Power On/Standby) button on the
head mounted unit for at least one second.
Audio/Video (in common)
Symptom
Cause/Action
No audio or video, or
audio or video is distorted
Refer to the “Startup Guide” and confirm that the AC
adaptor and HDMI cable are connected correctly.
Make sure that equipment connected to the HDMI IN
jack on the processor unit is on.
Make sure that equipment from which you wish to view
is selected correctly with the INPUT button on the
processor unit when the processor unit is used.
Confirm that the input signal is supported with this
system. For available signals, see “Video input” and
signal is not supported with this system, check the video
output and/or audio output settings on the connected
equipment.
Confirm that the HDMI cable is firmly plugged in. If video
quality does not improve, the HDMI cable may be
damaged. In that case, try a new cable.
If equipment is connected to the processor unit via an
AV amplifier (receiver), try connecting the equipment
directly to the processor unit instead. For details, refer to
the instruction manual of the equipment used.
Use either the supplied HDMI cable or a commercially
available HDMI cable identified as a High-Speed cable.
Also check section Video, Audio, or Wireless.
39
Video
Symptom
Cause/Action
No video, or output video
is distorted
When selecting “Side-by-Side” or “Over-Under” in “3D
Display” (in “3D Settings”), change the setting to “Off”
Make sure to disable video output with the Deep Color
signal on the connected equipment. If this option is not
available on the equipment and the content is being
output at 1080FP (Frame Packing), change the resolution
to 720FP.
Also check section Audio/Video (in common), or
Wireless.
The screen is dark or
blurry
Refer to the “Startup Guide” and confirm that the AC
adaptor and HDMI cable are connected correctly, and
that you are wearing the head mounted unit correctly.
The lens span may have been adjusted incorrectly
(page 26). Perform adjustment again by accessing “Lens
span adjustment” in the setting menu (page 28).
If the lenses in the head mounted unit are dirty, wipe
them with a soft dry cloth to clean them.
A bright portion of an
image is too bright, or a
dark portion of an image
is too dark
The phenomenon may appear when the RGB signal level
of the input signal is beyond the level specified by the
HDMI standards. Adjust the RGB signal output level on
the connected equipment or change the “HDMI Dynamic
Check the “Picture Mode” setting and change it to an
The screens suddenly go
off
After 3 hours of continuous viewing, the system will
display a warning screen and go off after 90 seconds of
inactivity. If you clear the message and continue
watching, the system will automatically go off after
another 3 hours to encourage healthy viewing habits.
For details, see “Prolonged viewing warning” (page 37).
Wear the head mounted unit correctly. 10 seconds after
the sensor in the head mounted unit detects that you
have removed the unit, the displayed screen will
automatically go off. For details, see “Power off when
The system will be turned off automatically if 30 minutes
elapse without signal input when “No signal Standby” is
Image display dims over
time
Although image display of photos or nearly motionless
images may dim over time, this does not indicate
system damage. To restore normal brightness, perform
some operation on the head mounted unit or the
connected equipment directly.
40
Symptom
Cause/Action
Some pixels on the
screens are not lit, or
some pixels are always lit
The panel fitted to this system is
manufactured with high-precision
technology, giving a functioning
pixel rate of at least 99.99%. Thus,
a very small proportion of pixels
may be “stuck”, either always off
(black), always on (red, green, or
blue), or flashing. This
Always-lit, or unlit
pixel
phenomenon occurs owing to the structure of this
system and does not indicate a malfunction. Sony is not
liable for replacement or return of the system because of
that phenomenon.
Some scenes on a Blu-ray
disc recorded at 24 fps
(matching the original
movie) look unnatural
In this case, try activating “24p True Cinema.” For details,
The screen flickers
Some source signals may cause the screen as a whole to
appear to flicker when “Panel Drive Mode” is set to
“Clear,” or when “24p True Cinema” is activated. For
Video is not shown in 3D
If the same image is displayed side by side or on top and
bottom, the 3D display format setting may be incorrect.
Try changing the “3D Display” setting in “3D Settings”
3D perception varies by viewer.
If the “3D Settings” menu is displayed but images are
not shown in 3D, try restarting the connected equipment
used for 3D playback.
The system does not support 2D to 3D conversion
(simulated 3D).
Viewing anaglyphic images in 3D requires anaglyphic
glasses (with red and blue lenses, for example).
Also check the settings of playback equipment
connected to the processor unit.
3D display is not activated
automatically
Make sure the “Auto 3D” setting in “3D Settings” is set to
3D content without a 3D format identification signal is
not automatically displayed in 3D. Try changing the “3D
Display” setting in “3D Settings” to “Side-by-Side” or
“Over-Under” (page 29).
41
Audio
Symptom
Cause/Action
There is no sound /
There is static /
Volume cannot be
increased
Adjust the volume using the VOL +/– buttons on the
head mounted unit.
Insert the headphone plug securely (Refer to “1 Connect”
in the “Startup Guide.”). The playback sound may not be
heard correctly if the headphone connection is wrong.
The headphone plug is dirty. Clean the headphone plug
with a soft dry cloth.
When the system is connected to HDMI CEC-compatible
home theater systems or AV amplifiers (receivers), check
the following settings.
– Make sure the “Control for HDMI” setting in “General
– Make sure “Control for HDMI” is activated on the AV
amplifier (receiver) or other equipment. For details,
refer to the instruction manual of the equipment used.
When the headphone jack on the processor unit is used,
there is a slight delay in volume change in response to
volume adjustment.
Also check section Audio/Video (in common), or
Wireless.
There is no surround-
sound effect
Make sure the “Surround” setting in “Sound” is not set to
“Off” (page 33).
Make sure the “Type of Headphones” setting in “Sound”
Sound perception varies by listener.
There is no bass
Make sure that the earbuds fit snugly in your ears
Audio signals are not
input in a “codec” audio
format*
The playback equipment may be configured to convert
audio output signals of a “codec” audio format to linear
PCM signals. In that case, in the playback equipment
settings, disable “codec” audio format conversion then
resume playback. For details, refer to the instruction
manual of the equipment used.
*
The “codec” audio format
represents the audio formats
other than linear PCM that are
described in “Audio input” of
Audio playback is not in
the right format
For dual mono audio, change the “Dual Mono” setting in
settings of connected equipment.
42
Wireless
Symptom
Cause/Action
No wireless connection
Make sure that the processor unit and the battery unit
are turned on.
It may take a while before the image appears on the
screen.
Audio or video interrupted
or stops
The WIRELESS indicator
does not light
The radio waves become weakened or interrupted,
depending on the distance or orientation of the
processor unit and the battery unit, or an obstruction
between the two units.
Make the positions of the processor unit and the battery
unit nearer (approximately 3 m or less), and orient the
two units with their SONY logos facing each other.
Wireless communication quality degrades if the panel
with the SONY logo (the side with antenna installed) of
the battery unit faces the floor, or away from the
processor unit.
If wireless communication cannot be achieved
successfully with the battery unit positioned flat, attach
the supplied stand to the battery unit and adjust its
orientation so that the SONY logo faces the processor
Use the system where there are no obstructions
between the processor unit and the battery unit.
There may be interference from other wireless devices.
Turn off those devices and check if the phenomenon
improves.
The transmission of audio and video signals, or the
correct operation of the unit may be affected by
interference if more than three wireless devices using
the same frequency band (60 GHz), including this
system, are used.
43
Charging
Symptom
Cause/Action
Charging cannot be
performed
Make sure that the AC adaptor and AC power cord are
firmly connected.
Charging may not be performed in excessively cold or
hot places. Perform charging under temperatures from
5 °C to 35 °C (41 °F to 95 °F).
Charging time is extended
Longer charging time is required if you charge with the
system turned on. Turn off the system before charging.
Charging may not be possible when the processor unit
and the battery unit are connected in wireless mode. To
perform charging, turn off the power of the units, or use
wired connection.
The battery may be deteriorated if the system has not
been used in more than one year. Contact your Sony
dealer or local authorized Sony service center.
HDMI Control
Symptom
Cause/Action
Connected equipment
cannot be controlled using
the buttons on the head
mounted unit
Make sure the “Control for HDMI” setting in “General
Make sure the connected equipment supports the HDMI
CEC functions.
Make sure “Control for HDMI” setting of the connected
equipment is configured correctly. For details, refer to
the instruction manual of the equipment used.
The connected AV amplifier (receiver) may not be
compatible with the system’s “Control for HDMI”
function. “Control for HDMI” function will not work
correctly in this case.
Controlling connected equipment by pressing buttons
on the head mounted unit may not be possible
immediately after turning the system on, or immediately
after activating “Control for HDMI” in “General Setup.”
Controlling connected equipment is not possible when
“Picture Mode” is set to “Game1,” “Game2,” “Game3”, or
44
Other Issues
Symptom
Cause/Action
“Control for HDMI” on a TV Refer to the instruction manual supplied with your TV,
cannot be used to control
the playback equipment
even when the system’s
HDMI pass-through is
used
and in the TV’s “Control for HDMI” setting, specify
playback equipment connected to the processor unit as
the controlling device.
Head mounted unit
Buttons on the head mounted unit do not function
buttons are unresponsive
unless you are wearing it.
“DEMO” appears in the
upper-right corner of the
setting menu screen
Contact your Sony dealer or local authorized Sony
service center.
Cannot adjust “Language
setting” because the
setting menu is in an
unfamiliar language
If initial setup is not finished, press the button
repeatedly to return to the language selection screen,
and then select your preferred language again.
If you have finished initial setup, follow these steps to
restore the system to the original, factory settings and
specify the correct language.
1 Press the MENU button to display the setting menus.
2 Press the button, select “ General Setup,” and
then press the MENU button.
3 Press the button and move the cursor to the bottom
setting.
4 Press the MENU button. (A “Reset to factory settings”
confirmation message is displayed.)
5 Press the button, and then press the MENU button.
(The system will restart.)
6 After the initial setting screen is displayed, press the
/ buttons to select your preferred language, and
then press the button.
7 Follow the instructions displayed to finish initial setup.
Discomfort in the nose or
forehead from contact
with the head mounted
unit
Adjust the position of the forehead supporter forward or
45
Warning by the indicators
The indicators on the battery unit and processor unit alert unusual conditions of
the system.
Indication
Error/Action
Battery unit
(power)
indicator
(orange)
Repeats flashing twice
every 3 seconds
Contact your Sony dealer or local
authorized Sony service center. The
battery unit may be damaged.
Repeats flashing three
times every 3 seconds
Temperature error in the battery unit.
Leave the unit for a while. Flashing
stops when the unit cools off.
Use the battery unit in a well-
ventilated location to prevent
blocking of the ventilation slots.
Repeats flashing five
times every 3 seconds
Battery error.
Stop using the system and contact
your Sony dealer or local authorized
Sony service center.
Processor unit
POWER
indicator
(red)
Repeats flashing twice
every 3 seconds
Contact your Sony dealer or local
authorized Sony service center.
The processor unit may be damaged.
Repeats flashing three
times every 3 seconds
Temperature error in the processor
unit.
Leave the unit for a while. Flashing
stops when the unit cools off.
Use the processor unit in a well-
ventilated location to prevent
blocking the ventilation slots.
46
2 Remove the three screws and the
front panel, then disconnect the
connector.
When Disposing of the
System
Connector
Front panel
For environment protection, remove
the built-in lithium-ion battery from
the system.
Before removing the battery, drain the
battery by removing the AC adaptor
and using the system only with the
battery.
• Take out the lithium-ion battery
for recycling.
Do not open the cabinet other
than when disposing of the
system.
• Be careful not to touch the end of
a screwdriver to the lithium-ion
battery when removing the
battery case. If the battery is
damaged, there is risk of leakage,
heat generation, fire, or explosion.
Note
• Be careful not to damage the cord
cover with metallic tweezers, etc.
when you disconnect the connector.
3 Remove the six screws and the
battery case.
Drop off the remove battery case with
the battery attached for recycling.
Battery
Battery case
Removing the Battery Case
1 Remove the four screws, then
remove the bottom panel from the
battery unit.
Screw
Rubber foot
Bottom panel
Note
• Do not remove the battery from the
battery case.
47
Dimensions (W×H×D, including largest
protrusions)
Processor unit:
Specifications
Approx. 150 mm × 31 mm ×
107 mm
(6 in. × 1 / in. × 4 / in.)
Head mounted unit:
Power requirement
Processor unit:
1
1
4
4
DC IN jack 8.4 V
Approx. 189 mm × 148 mm ×
270 mm
Head mounted unit and battery unit:
Micro USB jack (for charging)
5 V DC
1
7
3
2
8
4
(7 / in. × 5 / in. × 10 / in.)
(excluding top headband, and
bottom headband length
adjusted in the center)
Power consumption
Processor unit:
Battery unit:
Approx. 80 mm × 26 mm ×
119 mm
8.0 W (in wireless operation)
4.0 W (in wired operation)
0.4 W (in standby mode)
5.0 W (in wireless standby
mode)
2.0 W (in HDMI pass-through
mode)
1
1
3
4
16
4
(3 / in. × 1 / in. × 4 / in.)
Mass
Processor unit:
Approx. 250 g (8.9 oz)
(excluding connecting cables)
Head mounted unit:
Head mounted unit and battery unit:
11 W (during charging)
Approx. 320 g (12 oz)
(including top light blockers,
and excluding connecting
cords)
Battery charging time
Head mounted unit and battery unit:
Approx. 4.5 hours (in standby
mode at 23 °C (74 °F))
Battery unit:
Approx. 210 g (7.5 oz)
(excluding connecting cord)
Approx. 5.5 hours (in wired
operation at 23 °C (74 °F))
Display resolution
Battery operating time
1,280 dots (horizontal) × 720 dots
(vertical)
Head mounted unit and battery unit:
Approx. 3 hours (in wireless
operation at 23 °C (74 °F))
Approx. 7 hours (in wired
operation at 23 °C (74 °F))
Approx. 3 hours (in MHL
Interpupillary distance
53.0 mm – 76.7 mm
1
1
8
8
(2 / in. – 3 / in.)
operation at 23 °C (74 °F))
Input and output connectors
Processor unit:
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
HDMI IN 1:
19-pin standard connector
HDMI IN 2:
19-pin standard connector
HDMI IN 3:
Operating humidity
25 % to 80 %
19-pin standard connector
HDMI OUT (TV)*:
19-pin standard connector
HDMI OUT (HMD):
19-pin standard connector (on
front panel)
48
1) not available for MHL input
Headphone jack:
Stereo phone jack
Head mounted unit:
Headphone jack:
Stereo minijack
Battery unit:
2) not available for MHL input, and Frame
Packing and Top-and-Bottom formats
3) not available for MHL input and Frame
Packing format
HDMI IN/MHL:
19-pin standard connector
MHL 1 supported
MHL: 5 V, 500 mA power
supply capacity
Wireless section
Compatible standards
WirelessHD 1.1
Modulation method
OFDM
Usable frequency
59.40 GHz - 63.72 GHz (ch2 to
ch3)
*
When HDMI pass-through is activated,
signals supplied to the processor unit are
passed through the processor unit to the
HDMI output. However, the following
signals are not compatible with pass-
through.
Communication distance
Approx. 7 m (23 feet)*
*
The communication distance varies
– Video signals at 4k resolution (at a high
resolution exceeding 3,840 (horizontal)
× 2,160 (vertical) pixels)
depending on the conditions of use.
Headphones
Video input
Video input (2D formats):
Frequency response:
4 Hz - 27,000 Hz
Impedance:
480/60p, 576/50p, 720/24p, 720/
50p, 720/60p, 1080/50i, 1080/60i,
1080/24p, 1080/50p , 1080/60p
16 Ω (1 kHz)
1)
1)
AC adaptor AC-UD10 (for the head
mounted unit and battery unit)
Rated input
100 V – 240 V AC, 50 Hz/60 Hz,
0.2 A
Rated output
Video input (3D formats: Frame
Packing, Side-by-Side and Top-and-
Bottom formats):
1)
1)
2)
720/50p , 720/60p , 1080/50i ,
3)
2)
1)
1080/60i , 1080/24p , 1080/50p ,
3)
1080/60p
5 V DC, 1.5 A
Audio input
Battery unit:
Linear PCM (2-channel):
32/44.1/48 kHz
Processor Unit:
Linear PCM (2-channel):
Up to 192 kHz
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
–20 °C to +60 °C (–4 °F to 140 °F)
Dimensions (W × H × D)
Approx. 78 mm × 22 mm ×
36 mm
1
7
7
Linear PCM (multi-channel)
MPEG-2 AAC
Dolby Digital
8
8
16
(3 / in. × / in. × 1 / in.)
Mass
Approx. 45 g (1.6 oz)
Dolby Digital EX
Dolby Digital Plus
Dolby TrueHD
DTS
DTS-ES
AC adaptor AC-L200D (for the processor
unit)
Rated input
100 V – 240 V AC, 50 Hz/60 Hz,
0.35 A – 0.18 A
Rated output
DTS 96/24
DTS-HD Master Audio
DTS-HD High Resolution Audio
DTS-HD LBR
8.4 V DC, 1.7 A
49
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
–20 °C to +60 °C (–4 °F to 140 °F)
Dimensions (W × H × D)
Approx. 48 mm × 29 mm ×
81 mm
Technology Used in This System
• The processor unit enables the user
to hear immersive multi-channel
virtual surround-sound with depth,
produced by the headphones and
7.1-channel Virtualphones
15
3
1
16
16
4
(1
/
in. × 1 / in. × 3 / in.)
Technology (“VPT”).
Mass
Approx. 170 g (6 oz)
• More immersive game play with
accurate sound localization can be
enjoyed by listening in Game mode,
which produces a sound stage
specifically designed for games with
multi-channel surround-sound
effects. Game mode sound stage
design for this system was
Supplied accessories
System specifications and appearance
are subject to change for
improvement without notice.
supervised by sound designers at
Sony Computer Entertainment.
50
Trademarks
• The terms HDMI™ and HDMI High-
Definition Multimedia Interface, and
the HDMI Logo are trademarks or
registered trademarks of HDMI
Licensing LLC in the United States
and other countries.
• MHL™, Mobile High-Definition Link
and the MHL Logo are trademarks or
registered trademarks of MHL
Licensing, LLC.
• Manufactured under license from
Dolby Laboratories.
Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby
Laboratories.
• For DTS patents, see
Manufactured under license from
DTS Licensing Limited.
DTS, DTS-HD, the Symbol, & DTS and
the Symbol together are registered
trademarks of DTS, Inc. © DTS, Inc.
All Rights Reserved.
• WirelessHD™ is a registered
trademark of Silicon Image, Inc.
• “PlayStation” is a registered
trademark of Sony Computer
Entertainment Inc. Also, “PS3” is a
trademark of the same company.
• “VPT,” Virtualphones Technology is a
trademark of Sony Corporation.
• Other system and product names
are generally trademarks or
registered trademarks of the
manufacturers. ™ and ® marks are
not indicated in this document.
51
© 2013 Sony Corporation Printed in Japan
4-471-977-11(1)
|