I N S T A L L A T I O N I N S T R U C T I O N S
S S 4 V C / S S 6 V C
PN.33-2900 11.02
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: Read all of these instructions before you operate and
save instructions for later use.
1. Read Instructions - all the safety and operating instructions should be read
before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating
instructions should be adhered to.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
4. Follow Instructions - All operating and use instructions should be followed.
5. Water and Moisture- The appliance should not be used near water - for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, and the like.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
6. Carts and Stands - The appliance should be used only with a cart or stand
that is recommended by the manufacturer. An appliance and cart
combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
SERVICE PERSONNEL.
7.Ventilation - The appliance should be situated so that its location or position
does not interfere with its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similar surface that may block
the ventilation openings; or, placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air through the ventilation
openings.
The lighting flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
8. Heat - The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.
9. Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
10. Object and Liquid Entry - Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through openings.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
11. Damage Requiring Service - The appliance should be serviced by qualified
service personnel when:
A. Objects have fallen or liquid has been spilled into the appliance; or
B. The appliance has been exposed to rain; or
WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. THE APPARATUS SHALL NOT
BE EXPOSED TO DRIPPING OR SPLASHING. NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
C. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
D. The appliance has been dropped or the enclosure damaged.
12. Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should be
referred to qualified service personnel.
Note: With the SS6VC (not shown), you can add up to 2 more rooms.
B. Speaker Connection:
PLACEMENT
Because the SS4VC and SS6VC both contain resistors which
consume power and dissipate current in the form of heat, the unit
should be placed in a location that won’t heat other source
equipment and where there is good ventilation. If placing it in an
enclosed cabinet or between shelving, make sure there is adequate
space (at least two inches) on all sides and between the top of the
switcher and any shelving, cabinetry, or components placed above
it. A fan may be needed to draw air through the cabinet or shelving
unit if components get too warm. We recommend that you do not
place the unit on top of your receiver or amplifier.
1. With appropriate speaker wire, connect the first pair of speakers
to the left SPEAKER 1 connections on the back of the
SS4VC/SS6VC. Make sure the speaker positive (+) is connected to
the SS4VC/SS6VC positive (+), the speaker negative (-) to the
SS4VC/SS6VC negative (-).
2. Repeat step 1 for the remaining speaker pairs.
FRONT PANEL OPERATION
Since your SS4VC and SS6VC will be used as a central switcher for
multiple speaker pairs, it should be easily accessible. When placing
it with other electronics, the SS4VC and SS6VC should be placed in
a location that will accommodate the mass of speaker wires that will
be connected between it, the speakers, and receiver or amplifier.
Operation of the SPEAKER Buttons:
To e ng a ge a ny p a i r of speakers, push in the button which
corresponds to the pair of speakers you want to turn on. The “in”
position means the speakers are on.Any combination of the speaker
pairs may be played at once. To disengage any pair of speakers, push
in the button which corresponds to the pair of speakers you want to
turn off. The “out” position means the speakers are off.
WIRING
Note: A slight decrease in volume may occur when additional
speakers are engaged.
IMPORTANT: Always use high grade speaker wire such as Sonance
MediaLinQ™.We recommend 18 GA wire for runs of 50 feet or less,
16 GA for runs of 50-100 feet, or 14 GA for runs over 100 feet.
A. Source Connection:
1. Connect the left speaker output of the receiver or amplifier to the
left INPUT connector of the SS4VC/SS6VC (see diagram above).
Make sure that the positive (+) terminal of the receiver or amplifier
connects to the positive (+) terminal of the input connector of the
SS4VC/SS6VC. The negative (-) connection should be connected to
the negative (-) terminal of the input connector of the
SS4VC/SS6VC.
2. Repeat step 1 for the right side, connecting the right speaker
output of the receiver or amplifier to the right INPUT connector of
the SS4VC/SS6VC (see diagram above).
TROUBLESHOOTING
WARRANTY COVERAGE (USA ONLY)
• Verify that the input connection is properly attached to the
receiver or amplifier and that the receiver or amplifier is
operating properly.
If, within five (5) years from the date shown on the bill of sale, the
unit fails due to a defect in workmanship or materials, Sonance will,
at its option and at no charge to the purchaser, repair or replace the
components of such unit which proves to be defective.
• Verify that the speaker selector button is pushed “in” (on position)
and then verify that your speakers are properly wired.
For this warranty to be effective, the bill of sale must show that the
unit was purchased from an authorized Sonance retailer. This
warranty shall apply exclusively to the original purchaser and shall
not apply to units purchased for industrial or commercial use.
SERVICE
Furthermore, this warranty shall not apply if:
If you have any questions about the operation or installation of your
SS4VC/SS6VC, please call our Technical Assistance Department on
any business day at: (800)582-0772 or (949)492-7777 from
7 a.m. to 5 p.m. PST.
1. Damage to the unit was caused by accident, abuse, or misuse;
2. The unit was modified or repaired by unauthorized personnel; or
3. The unit was not used as outlined in the operating instructions
Should your product require repair or service, contact your
authorized Sonance retailer for help or use the following procedure:
Exclusions and Limitations
The warranty set forth above is in lieu of all other warranties,
express or implied, of merchantability, fitness for a particular
purpose, or otherwise. The warranty is limited to Sonance products
registered herein and specifically excludes any damage to any
associated equipment, which may result for any reason from use
with this product.
1. Prior to calling, note the product model number, serial number,
purchase date, and original retailer’s name and address.
2. Contact our Technical Assistant Department at the number(s) above
and describe the problem. If required a Return Merchandise
Authorization (RMA) number will be issued. IMPORTANT: Do not
return the unit to Sonance without first obtaining an RMA number.
Sonance shall, in no event, be liable to incidental or consequential
damages arising from any breach of this warranty or otherwise.
This warranty gives you specific legal rights, and you may have
other rights, which vary from state to state.
3. If you are directed to return the unit to Sonance for repair, pack the
unit in its original shipping cartons (inner & outer). Replacement
packaging can be obtained from Sonance for a small charge. Note, it
is best if you place it into an additional outer "overcarton"
before shipment to minimize the chance of theft in shipment.
SPECIFICATIONS
4. Contact United Parcel Service, Federal Express, or RPS to arrange
prepaid (not collect) shipping. Do not use the United States Postal
Service. IMPORTANT: Freight collect shipments will be refused.
Power Rating:
Switch Type:
75 Watts RMS Maximum input per channel
12 Position light touch silent rotary switch
“Make Before Break”
Te rminal Type:
Toggle Quick Disconnect 20-14 AWG wire capacity
20-20KHz+1dB
5. Write the Return Merchandise Authorization number on the
outside of the shipping carton.
Frequency Response:
Speaker Impedance:
Total Attenuation:
8 Ω per zone
-42 dB; full clockwise position is straight-through, full counter
clockwise position is off
6.For warranty work, please include a copy of the original bill of sale
inside the package.
Attenuation by step:
top 7 steps are -3dB per step, lowest 4 steps are -6dB per step
Dimensions (W x H x D):
RMF (W x H x D):
16 7/8" x 2 3/16" x 10 1/4" (429mm x 56mm x 260mm)
19" x 1 3/4" x 10 1/4" (483mm x 45mm x 260mm)
Ship the packaged unit to:
Te c hnical Assistance Department
Sonance
212 Avenida Fabricante
San Clemente, CA 92672-7531
Specifications and features subject to change without notice.
SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 Technical Support (800) 582-0772 ©2002 All rights reserved. Sonance is a registered trademark of Dana Innovations
www.sonance.com
|