Sonance Speaker MARINERSST User Manual

I N S T R U C T I O N M A N U A L  
®
S O N A N C E S Y M P H O N Y  
S S T R / S S T / S R S 1  
IN-CEILING/IN-WALL SPEAKERS  
SRS1: 5.1-Channel Home Theater System  
INTRODUCTION  
®
Locate the left and right SRS1 surround speakers on the ceiling between 2 feet  
and 6 feet behind the listening position. The speakers should be between 6 feet  
and 10 feet apart. Orient the speakers so the tweeters face the front and rear  
walls of the room. Use Figure 3 as a guide.  
Thank you for purchasing Sonance Symphony SSTR/SST/SRS1-series speakers.  
When properly installed your new speakers will give you years of entertainment  
pleasure. This manual covers the following speaker models: Symphony S623SSTR;  
Symphony S621SSTR, Symphony S623SST and Symphony SRS1.  
Left & Right  
Surround  
Speakers  
SAFETY WARNING:  
®
These speakers have FastMount tabs that prevent the speaker from falling out  
of the mounting hole during the installation process.  
The edges of the FastMount tabs are very sharp.  
Use caution when handling the speaker.  
6' – 10'  
TV  
apart  
BOX CONTENTS  
Sonance Symphony SSTR and SST speaker boxes contain (1) Symphony speaker, (1)  
plastic paint plug (installed on the front of the speaker), (1) paintable grille and  
(1) mounting cutout template (in packaging).  
2' – 6'  
Sonance Symphony SRS1 speaker boxes contain (2) Symphony speakers, (2) paint  
plugs (installed on the fronts of the speakers), (2) paintable grilles and (1) mount-  
ing cutout template (in packaging).  
FI G U R E 3: 5.1-CH A N N E L HOM E TH E AT E R SP E A K E R PL AC E M E N T  
SPEAKER PLACEMENT  
S623SST/S623SSTR/S621SSTR  
SRS1: 7.1-Channel Home Theater System  
®
Sonance Symphony Single Stereo Technology SST and SSTR speakers are ideal for  
Left & Right Surround Speakers: Place the left and right surround speak-  
use in hallways, bathrooms, closets, or in any location where a pair of stereo speak-  
ers would be impractical. Because a single Symphony SST/SSTR speaker reproduces  
both stereo channels from a single location, it will deliver outstanding perform-  
ance from an extremely wide variety of mounting locations. The chart in Figure 1  
shows how far apart the speakers can be placed at different ceiling heights while  
still providing good coverage for distributed audio (as shown in Figure 2).  
ers directly to the sides of the listening position, between 6 feet and 10 feet apart.  
Surround Back Speakers: Place the surround back speakers between 2 feet  
and 6 feet behind the listening position. The surround back speakers should be  
closer together than the left and right surround speakers — between 3 feet and  
6 feet apart.  
Use Figure 4 as a guide.  
Speaker Spacing (in feet) for a Distributed Audio System  
Standing Listener Seated Listener  
Left & Right  
Surround Speakers  
8-foot ceiling  
10-foot ceiling  
12-foot ceiling  
14-foot ceiling  
5.7'  
9.7'  
9.5'  
Surround  
Back  
13.5'  
17.5'  
21.5'  
Speakers  
13.7'  
17.7'  
3' – 6'  
TV  
apart  
FI G U R E 1: DI S T R I B U T E D AU D I O SP E A K E R SPAC I N G  
2' – 6'  
S
SPPAEACIKNEGR  
COVERAGE  
AREA  
COVERAGE  
AREA  
FI G U R E 4: 7.1-CH A N N E L HOM E TH E AT E R SP E A K E R PL AC E M E N T  
FI G U R E 2: DI S T R I B U T E D AU D I O COV E R AG E AR E A  
1
 
®
SONANCE SYMPHONY SSTR, SST & SRS1  
SPEAKER ADJUSTMENTS  
SPECIFICATIONS  
Pivoting Woofer  
S623SSTR  
Tweeter:  
Two 1" (25mm) Silk domes, Ferrofluid-cooled  
The Symphony S623SSTR, S621sstr and SRS1 mocels have a pivoting woofer assem-  
bly. These pivoting drivers allow you to direct sound toward or away from the  
listening area, depending on how the speakers are being used:  
Woofer:  
6½" (165mm) Carbon fiber cone, dual voice coil, rubber  
surround, pivoting  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
Grille Material:  
Adjustments:  
Dimensions (Dia. x Depth): 9¾" (248mm) x 53/16" (132mm)  
Cutout Diameter:  
Shipping Weight:  
43Hz – 20kHz ±3dB  
• Pivoting the woofer towards the listening position will maximize the speaker’s  
clarity and definition.  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 135 Watts maximum  
90dB SPL (2.83V 1 meter)  
Perforated aluminum  
• If you’re using the speakers as surround channel speakers in a home theater,  
you can create a more diffuse, spacious surround effect by aiming the woofers  
towards a wall or window,  
away from the listeners.  
±3dB Tweeter level  
To pivot the woofer, apply  
pressure on the outer edge  
of the tweeter support brack-  
et, as shown in Figure 7. Do  
not touch or apply pressure  
to the woofer cone.  
85/32" (207mm)  
5 lbs. (2.3kg) Each  
S621SSTR  
Tweeter:  
Two ¾" (19mm) Silk domes, Ferrofluid-cooled  
Woofer:  
6½" (165mm) Polypropylene cone, dual voice coil, rubber  
surround, pivoting  
To Pivot the Woofer:  
Apply pressure on the outer  
edge of the tweeter support  
bracket, as shown in  
Figure 8. Do not touch or  
apply pressure to the woofer  
cone.  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
Grille Material:  
Adjustments:  
Dimensions (Dia. x Depth): 9¾" (248mm) x 53/16" (132mm)  
Cutout Diameter:  
Shipping Weight:  
50Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 100 Watts maximum  
88dB SPL (2.83V 1 meter)  
Perforated aluminum  
FI G U R E 7:  
PI VOT I N G T H E WO O F E R  
None  
Tweeter Level Control  
85/32" (207mm)  
4.5 lbs. (2.0kg) Pair  
The S623SSTR has a tweeter level  
control switch (see Figure 8) that lets  
you boost or cut the tweeter’s level by  
3dB. This allows you to adjust the  
speaker’s brightness to better match  
your listening room or personal taste.  
S623SST  
Tweeter:  
Woofer:  
Two 1" (25mm) Silk domes, Ferrofluid-cooled  
6½" (165mm) Carbon fiber cone, dual voice coil, rubber  
surround  
Tweeter  
Level Control  
Once you have installed the speakers,  
listen to a variety of music that you  
are familiar with. If the music all  
tends to sound too bright or dull, use  
the Tweeter Level Control to compensate. If some recordings sound dull and some  
sound bright the speaker is accurately reproducing differences in the recordings,  
and you should leave the control in the middle (0dB) position.  
FI G U R E 8:  
TW E E T E R LE V E L CO N T RO L  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
43Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 135 Watts maximum  
90dB SPL (2.83V 1 meter)  
Perforated aluminum  
Grille Material:  
Dimensions (W x H x D): 8¼” x 123/16" x 33/8" (210mm x 310mm x 86mm)  
Cutout Dim. (W x H):  
Shipping Weight:  
613/16" x 1011/16" (172mm x 270mm)  
5 lbs. (2.3kg) Each  
SRS1  
Tweeter:  
Woofer:  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
Two 1" (25mm) Silk domes, Ferrofluid-cooled  
6½" (165mm) Carbon fiber cone, rubber surround, pivoting  
55Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 150 Watts maximum  
90dB SPL (2.83V 1 meter)  
Grille Material:  
Perforated aluminum  
Dimensions (Dia. x Depth): 9¾" (248mm) x 53/16" (132mm)  
Cutout Diameter:  
Shipping Weight:  
85/32" (207mm)  
11 lbs. (5.0 KG) Pair  
3
 
Freight collect shipments will be refused. It is preferable to ship this product in  
the original shipping container to lessen the chance of transit damage. In any case,  
the risk or loss or damage in transit is to be borne by the purchaser. If upon  
examination at the factory or Authorized Sonance Dealer it is determined that the  
unit was defective in materials or workmanship at any time during this warranty  
period, Sonance or the Authorized Sonance Dealer will, at its option, repair or  
replace this product at no additional charge, except as set forth below. If this  
model is no longer available and can not be repaired effectively, Sonance, at is  
sole option, may replace the unit with a current model of equal or grater value.  
In some cases where a new model is substituted, a modification to the mounting  
surface may be required. If mounting surface modification is required, Sonance  
assumes no responsibility or liability for such modification. All replaced parts and  
product become the property of Sonance. Products replaced or repaired under this  
warranty will be returned to the original retail purchaser, within a reasonable time,  
freight prepaid.  
TECHNICAL ASSISTANCE AND SERVICE  
If you any have questions about the operation or installa-  
tion of this product, please call our Technical Assistance  
Department on any business day at (800) 582-0772 or (949)  
492-7777; from 7 a.m. to 5 p.m., PST.  
If your speakers should need repair or service, contact your Sonance Authorized  
Dealer for help, or use the following procedure:  
1. Prior to calling, note the product’s model number, serial number, purchase date,  
and the name and address of the dealer where you purchased the product.  
2. Contact our Technical Assistance Department at the above number(s) and  
describe the problem the unit is experiencing. If applicable, they will issue a  
Return Authorization Number.  
IMPORTANT: YOU MUST HAVE PRIOR AUTHORIZATION  
TO RETURN YOUR SPEAKER TO SONANCE!  
This Warranty does not include service or parts to repair damage caused by acci-  
dent, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures,  
commercial use, voltage inputs in excess of the rated maximum of the unit, or  
service, repair or modification of the product which has not been authorized or  
approved by Sonance. This Warranty also excludes normal cosmetic deterioration  
caused by environmental conditions. This Warranty will be void if the Serial Number  
on the product has been removed, tampered-with or defaced. This Warranty is in  
lieu of all other expressed warranties. If the product is defective in materials or  
workmanship as warranted above, the purchaser’s sole remedy shall be repair or  
replacement as provided above. In no event will Sonance be liable for any inci-  
dental or consequential damages arising out of the use or inability to use the  
product, even if Sonance or an Authorized Sonance Dealer has been advised of the  
possibility of such damages, or for any claim by any other party.  
3. If you’re directed to return the unit to Sonance for repair, pack the unit in its  
original shipping carton. If needed, you can obtain replacement packaging from  
us for a small charge. Note: it is best if you place the box into an additional  
outer “overcarton” before shipment to minimize a chance of theft in shipment.  
Please include a copy of the original bill of sale inside the package.  
4. Contact a package delivery company such as United Parcel Service or Federal  
Express to arrange prepaid (not collect) shipping. Do not use the U.S. Postal  
Service.  
IMPORTANT: Freight collect shipments will be refused.  
5. Write the Return Authorization Number on the outside of the  
shipping carton.  
6. Ship the packaged unit to:  
Some states do not allow the exclusion or limitation of consequential damages, so  
the above limitation and exclusion may not apply. All implied warranties on the  
product are limited to the duration of this expressed Warranty. Some states do not  
allow limitation on the length of an implied warranty. If the original retail pur-  
chaser resides in such a state, this limitation does not apply.  
QUALITY ASSURANCE DEPARTMENT  
SONANCE  
212 AVENIDA FABRICANTE  
SAN CLEMENTE, CA 92672-7531  
EXCLUSIONS AND LIMITATIONS  
LIMITED LIFETIMEWARRANTY COVERAGE  
(U.S. ONLY)  
The warranty set forth above is in lieu of all other warranties, express or implied,  
of merchantability, fitness for a particular purpose, or otherwise. The warranty is  
limited to Sonance products registered herein and specifically excludes any dam-  
age to loudspeakers and other allied or associated equipment which may result for  
any reason from use with this product. Sonance shall, in no event, be liable for  
incidental or consequential damages arising from any breach of this warranty or  
otherwise. This warranty gives you specific legal rights, and you may have other  
rights which vary from state to state.  
SONANCE WARRANTS TO THE ORIGINAL RETAIL PURCHASER ONLY THAT THIS  
SONANCE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIALS AND WORK-  
MANSHIP, PROVIDED THE SPEAKER WAS PURCHASED FROM A SONANCE  
AUTHORIZED DEALER.  
Defective products must be shipped, together with proof of purchase, prepaid  
insured to the Authorized Sonance Dealer from whom they were purchased, or to  
the Sonance factory at the address listed on this instruction manual.  
©2007 Sonance. All rights reserved. Sonance, Sonance Symphony, Single-Stereo Technology, RotoLock and FastMount are registered trademarks of Dana Innovations.  
Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product specification information visit  
212 Avenida Fabricante • San Clemente, CA 92672-7531 USA • (800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772  
33-4341  
06/07  
 

Sennheiser Microphone MKH 8000 User Manual
Shark Vacuum Cleaner EP600 User Manual
Sharp Blu ray Player BD HP21U User Manual
Shure Microphone 515BSLX User Manual
SIIG TV Cables 04 0841A User Manual
Sony Car Video System SDM X52 User Manual
Sony Music Mixer 267 User Manual
Spectra Headphones TW4080 User Manual
Stamina Products Treadmill 45 1003 User Manual
SV Sound Car Speaker PB12 ISD V User Manual