Step 1 : Conꢀgure the Network
To reset to the factory default settings
This Setup Guide explains how to conꢀgure C-6700WG
(this product) to be used in a wireless LAN environment.
Perform the factory default conꢀguration according to the connection between this product
and the PC.
This product has 3 methods of initial conꢀguration as listed below:
1. Remove the AC plug from the electric outlet.
- To perform the factory default conꢀguration with a wireless LAN connection, refer to
- Conꢀguration through a wireless LAN
- Conꢀguration through a wired LAN
- Conꢀguration using a USB memory
Important:
.
2. Push and hold the button on the print server while re-inserting the AC plug
into the electric outlet. Continue holding.
Conꢀgure Through a Wireless LAN
The print server only needs to be configured on
one computer.
- To perform the factory default conꢀguration with a wired LAN connection, refer to
Conꢀgure Through a Wired LAN.
Setup Guide
3. The Status LED(Orange) will light when the factory default conꢀguration
settings have been restored. Release the push switch.
This Setup Guide describes how to conꢀgure this product through a
wireless LAN or wired LAN.
After setup is complete, go to:
‘Step 2: Install the Applications’for each computer
that will use the printer.
If this product has been used in another network, reset it to the factory default settings.
For details on the factory default conꢀguration, refer to To reset to the factory default settings.
For other conꢀguration methods, please refer to the users manual.
5.
2.
3.
4.
Conꢀgure Through a Wireless LAN
1.
The following item is required:
W A 0 3 7 9 0 X X
Warranty Booklet
Contents
Verify the Wireless LED(Green) blinks.
Insert the CD-ROM (CX User Software) into your Windows PC.
Check the message and click OK.
Install the printer driver on your PC.
For details, refer to the manual that came with
your printer.
Connect the AC adapter to this product and the power
plug to the outlet.
C-6700WG
Power Supply
Rubber Feet
Stand
CX User Software
Setup Guide
-USB cable
(Do not connect the printer to this product yet. Printer
will be connected in ‘18’)
(Install the printer driver on your PC and make
sure you can print with a directly attached USB
connection from your computer before using
this product.)
When the product is placed in the horizontal (side) position, please use the rubber feet provided to prevent the unit from sliding.
Place one on each corner.
Use to connect this product and a printer.
There is no need to purchase a new USB cable when a cable was
bundled with the printer to be connected to this product.
For User Registration
Customer Support
7.
8.
10.
6.
9.
USA : silex technology america, Inc.
E-mail : [email protected]
Phone: 801-748-1199
US Toll Free Phone: 866-765-8761
Note: A more detailed manual including troubleshooting tips can be found on the CD
(Insert the CD, and click on Manual when the Autorun menu appears) of this product.
Read the SOFTWARE LICENSE AGREEMENT and click
Yes.
If the screen above is displayed, select the wireless
network card to be used and click OK.
CX Wireless Setup screen is displayed.
Check the notes on the screen and select
Conꢀgure print server wirelessly from your
computer and click Next.
Click Wireless.
Startup menu is displayed.
Click Print Server Setup.
* In a Windows XP (SP2 or higher) or Vista environment, the above message
will be displayed. Sele. ct Yes
* The User Account Control screen is displayed when conꢀguration is performed
on Windows Vista. Select Continue.
Safety instructions are noted in the Readme ꢀle on the CX User Software . Be sure to read
them before using this product.
* This screen is displayed only when two or more
network cards are installed on your PC.
Select this product and click Next.
- Safety instructions regarding the radio waves
Please note the following instructions:
- Do not use this product near medical devices such as a heart pacemaker. The radio
wave generated by this product may interfere with the operation of these devices and
may threaten one's life.
11.
12.
14.
13.
- Do not use this product near microwave ovens. The radio wave used by microwave
ovens may cause interference to this product.
Introduction
If the wireless settings on the PC diꢁer from the
conꢀguration information on the screen above, change
the PC wireless settings to match those displayed on
the screen.
Select the SSID for your home or oꢂce
wireless network. If your network is security
enabled, enter the network key or password
Select a product to be conꢀgured and click Next.
Select Get IP Address Automatically
and click Next.
* If the wireless network that you wish to use is not shown in
the list, click Detailed Conꢀg and conꢀgure each setting.
If the screen above is displayed, you need to change
the wireless settings on the PC manually.
Read the message and click OK.
Collect wireless LAN setting information
* If your product is not displayed on the list, click Refresh.
Next.
and conꢀrm it.
Click
Verify the wireless settings on the PC and click Next.
*
If multiple products are displayed in the list, check the
* If you use Windows XP or Vista and the setup utility automatically
changed the wireless settings on the PC, this screen is not displayed.
Ethernet Address on the label of this product.
To use this product over the wireless LAN network, you need to conꢀgure wireless LAN
settings as appropriate for your network. This information needs to be identical to the
communication devices such as an access point.
Please refer to your wireless network adapter documentation for
instructions on how to temporarily change your computer’s wireless
settings to match those of the print server.
*
Please collect the following information before the setup.
Important: When you make this temporary change, your computer will
no longer be connected to the wireless network or Internet. After you
have completed the setup for the print server, you will need to change
your computer’s wireless settings back to their current settings. Please
make sure you write down the settings for your wireless network before
you make these changes for the print server configuration.
Write down your network conꢀguration
<< If you did not need to change the
<< If you changed the wireless settings
on the PC manually in ‘11’, this
screen will appear
17.
18.
15.
16.
wireless settings on the PC manually
in ‘11’, this screen will appear
Wireless mode
Ad hoc (ch. ) / Infrastructure
>>
>>
The initial conꢀguration of
this product is complete and
you do not need to conꢀgure
the print server any more.
SSID
After setup is complete on one
computer, each user that wants
to use the Canon printer:
Encryption
method
WEP
/ WPA / WPA2
Go to
(Open / Shared)
Click Finish.
Select Yes and click Finish.
To ensure these settings take eꢁect,
unplug the AC adapter from the electrical
outlet and then plug it back in.
Connect the printer to be shared over the network along
with this product via a USB cable and insert the power
plug of this product into the outlet.
Step 2: Install the Applications
on the next page
Conꢀrm the conꢀguration parameters and
click Execute.
Encryption
method
Change the wireless settings on the PC
(that you have manually changed) back
to the previous settings written down in
‘11’.
* Application install screen will be displayed as
shown in Step 2 - 3.
WEP KEY
or
Pre-Shared
Key
Note: If you manually changed
the wireless settings at ‘11’
on your PC, go straight to
‘3’ in Step 2.
|