Sharp Flat Panel Television LQ201U1LW01 User Manual

LQ201U1LW01  
TFT-LCD Module  
(Model Number: LQ201U1LW01)  
Specifications  
Spec No.: LD-14115  
Dated: May 29, 2002  
 
RECORDS OF REVISION  
LQ201U1LW01  
SPEC No.  
DATE  
SUMMARY  
NOTE  
REVISED  
No. PAGE  
LD-14115  
Feb. 25. 2002  
1 st Issue  
 
LD-14115-1  
1. Application  
This specification applies to the color 20.1 UXGA TFT-LCD module LQ201U1LW01.  
These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include  
materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in  
any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express  
written permission of SHARP.  
The device listed in these specification sheets was designed and manufactured for use in OA equipment.  
In case of using the device for applications such as control and safety equipment for transportation(aircraft,  
trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require  
higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and  
redundant system design should be taken.  
In case of using the device for equipment that requires an extreme level of reliability, such as aerospace  
applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or  
other equipment for life support, contact and consult with a SHARP sales representative.  
SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply  
with the instructions and the precautions specified in these specification sheets.  
Contact and consult with a SHARP sales representative for any questions about this device.  
2. Overview  
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).  
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.  
Graphics and texts can be displayed on a 1600×3×1200 dots panel with about 16 million colors by supplying 48  
bit data signals(8bit×2pixel×RGB) , two display enable signals, two dot clock signals, +12V DC supply  
voltages for TFT-LCD panel driving and supply voltage for back light.  
It is a wide viewing-angle-module (Vertical viewing angle:170°Horizontal viewing angle:170°,CR10).  
 
LD-14115-2  
3. Mechanical Specifications  
Parameter  
Specifications  
Unit  
cm  
Display size  
51 (Diagonal)  
20.1 (Diagonal)  
Inch  
mm  
408.0 (H)×306.0 (V)  
1600 (H)×1200 (V)  
(1 pixelRGB dots)  
0.255(H)×0.255 (V)  
R,G,B vertical stripe  
Normally black  
Active area  
Pixel format  
Pixel  
Pixel pitch  
mm  
Pixel configuration  
Display mode  
436(W)×335 (H)×27.5 (D)  
3.8 (MAX)  
Unit outline dimensions *1  
Mass  
mm  
kg  
Surface treatment  
Anti-glare And hard-coating 2H  
*1.Note: excluding back light cables.  
The thickness of module (D) doesn’t contain the projection.  
Outline dimensions are shown in Fig.1.  
 
LD-14115-3  
4. Input Terminals  
4-1. TFT-LCD panel driving  
CN7A,CN7B (Interface signals and +12VDC power supply)  
Using connectors DF19G-20P-1H (Hirose Electric Co., Ltd.)  
Corresponding connectors DF19G-20S-1C (Hirose Electric Co., Ltd.)  
DF19G-20S-1F (Hirose Electric Co., Ltd.)  
Using LVDS receiverContained in a control IC  
Corresponding LVDS transmitterTHC63LVDM83R(Thine) or compatible  
CNA  
Pin No.  
1
Symbol  
Vcc  
Vcc  
Function  
Remark  
+12V power supply  
+12V power supply  
Gnd  
2
3
Vss  
4
Vss  
Gnd  
5
6
RAIN0-  
Negative (-) LVDS differential data input (A port)  
LVDS  
LVDS  
RAIN0+  Positive (+) LVDS differential data input (A port)  
7
Vss  
Gnd  
8
9
RAIN1-  
Negative (-) LVDS differential data input (A port)  
LVDS  
LVDS  
RAIN1+  Positive (+) LVDS differential data input (A port)  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Vss  
RAIN2-  
Gnd  
Negative (-) LVDS differential data input (A port)  
LVDS  
LVDS  
RAIN2+  Positive (+) LVDS differential data input (A port)  
Vss  
CKAIN-  
CKAIN+  Positive (+) LVDS differential clock input (A port)  
Vss  
RAIN3-  
RAIN3+  Positive (+) LVDS differential data input (A port)  
Vss  
BLON  
Gnd  
Negative (-) LVDS differential clock input (A port)  
LVDS  
LVDS  
Gnd  
Negative (-) LVDS differential data input (A port)  
LVDS  
LVDS  
Gnd  
Back light ON signal (output) Note1】  
Pull Up  
Note1BLON:It change from L to H at 7 frames after Vcc ON.  
CNB  
Pin No.  
1
Symbol  
Vcc  
Vcc  
Function  
Remark  
+12V power supply  
+12V power supply  
Gnd  
2
3
Vss  
4
Vss  
Gnd  
5
6
RBIN0-  
Negative (-) LVDS differential data input (B port)  
LVDS  
LVDS  
RBIN0+  Positive (+) LVDS differential data input (B port)  
7
Vss  
Gnd  
8
9
RBIN1-  
Negative (-) LVDS differential data input (B port)  
LVDS  
LVDS  
RBIN1+  Positive (+) LVDS differential data input (B port)  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Vss  
RBIN2-  
Gnd  
Negative (-) LVDS differential data input (B port)  
LVDS  
LVDS  
RBIN2+  Positive (+) LVDS differential data input (B port)  
Vss  
CKBIN-  
CKBIN+  Positive (+) LVDS differential clock input (B port)  
Vss  
RBIN3-  
RBIN3+  Positive (+) LVDS differential data input (B port)  
Vss  
SELLVDS  
Gnd  
Negative (-) LVDS differential clock input (B port)  
LVDS  
LVDS  
Gnd  
Negative (-) LVDS differential data input (B port)  
LVDS  
LVDS  
Gnd  
Select LVDS data order Note2】  
Pull Up  
Note2This module has dual pixel port to receive dual pixel data at the same time . A port receives first  
pixel data and B port receives second pixel data in dual pixel data.  
 
LD-14115-4  
 
 【Note2SELLVDS(Thine:THC63LVDM83R)  
Transmitter  
SELLVDS  
=L  
R0(LSB)  
R1  
Pin No  
51  
52  
54  
55  
56  
3
Data  
TA0  
TA1  
TA2  
TA3  
TA4  
TA5  
TA6  
TB0  
TB1  
TB2  
TB3  
TB4  
TB5  
TB6  
TC0  
TC1  
TC2  
TC3  
TC4  
TC5  
TC6  
TD0  
TD1  
TD2  
TD3  
TD4  
TD5  
TD6  
=H  
R2  
R3  
R4  
R5  
R2  
R3  
R4  
R5  
R6  
R7(MSB)  
G2  
G0(LSB)  
G1  
4
6
7
G3  
G4  
G5  
G6  
G2  
G3  
G4  
G5  
11  
12  
14  
15  
19  
20  
22  
23  
24  
27  
28  
30  
50  
2
G7(MSB)  
B2  
B0(LSB)  
B1  
B3  
B4  
B5  
B6  
B2  
B3  
B4  
B5  
B7(MSB)  
(NA)  
(RSV1)  
DE  
R0(LSB)  
R1  
G0(LSB)  
G1  
B0(LSB)  
B1  
(NA)  
(RSV1)  
DE  
R6  
R7(MSB)  
G6  
G7(MSB)  
B6  
B7(MSB)  
(NA)  
8
10  
16  
18  
25  
(NA)  
 
LD-14115-5  
4-2 Interface block diagram  
Using receiverContained in a control IC.  
Corresponding TransmitterTHC63LVDM83R(THine electronics),DS90C383,DS90C383A(National semiconductor)  
Computer side)  
(TFT-LCD side)  
8
RAIN0+(5)  
RA0RA7  
8
8
8
8
RA0RA7  
GA0GA7  
BA0BA7  
RAIN0-(6)  
GA0GA7  
RAIN1+(8)  
RAIN1-(9)  
RAIN2+(11)  
RAIN2-(12)  
8
BA0BA7  
RAIN3+(17)  
DEA  
CLK  
RAIN3-(18)  
DEA  
CLK  
RACLKIN+(14)  
PLL  
PLL  
RACLKIN-(15)  
A Port  
B Port  
RBIN0+(5)  
RBIN0-(6)  
8
RB0RB7  
GB0GB7  
BB0BB7  
8
8
8
RB0RB7  
GB0GB7  
BB0BB7  
8
8
RBIN1+(8)  
RBIN1-(9)  
RBIN2+(11)  
DEB  
TxIN18~20  
RBIN2-(12)  
RBIN3+(17)  
DEB  
RBIN3-(18)  
RBCLKIN+(14)  
RBCLKIN-(15)  
PLL  
PLL  
 
LD-14115-6  
< SELLVDS= Low >  
1 cycle  
CKAIN+  
CK^AIN-  
RAIN0+  
RAIN0-  
RA1  
GA2  
BA3  
RA7  
RA0  
GA1  
BA2  
RA6  
GA0  
BA1  
DEA  
NA  
RA5  
BA0  
NA  
RA4  
GA5  
NA  
RA3  
GA4  
BA5  
GA7  
RA2  
GA3  
BA4  
GA6  
RA1  
GA2  
BA3  
RA7  
RA0  
GA1  
BA2  
RA6  
GA0  
RAIN1+  
BA1  
DEA  
NA  
RAIN1-  
RAIN2+  
RAIN2-  
RAIN3+  
RAIN3-  
BA7  
BA6  
Tcsq  
CKBIN-  
CKBIN+  
RBIN0+  
RBIN0-  
RB1  
GB2  
BB3  
RB7  
RB0  
GB1  
BB2  
RB6  
GB0  
BB1  
DEB  
NA  
RB5  
BB0  
RSV1  
BB7  
RB4  
RB3  
GB4  
BB5  
GB7  
RB2  
GB3  
BB4  
GB6  
RB1  
GB2  
BB3  
RB7  
RB0  
GB1  
BB2  
RB6  
GB0  
BB1  
DEB  
NA  
RBIN1+  
GB5  
NA  
RBIN1-  
RBIN2+  
RBIN2-  
RBIN3+  
RBIN3-  
BB6  
DE: Display Enable  
RSV1: Reserve (Fixed GND)  
NA: Not Available  
 
LD-14115-7  
< SELLVDS= High >  
1 cycle  
CKAIN+  
CKAIN-  
RAIN0+  
RAIN0-  
RA3  
GA4  
BA5  
RA1  
RA2  
GA3  
BA4  
RA0  
GA2  
BA3  
DEA  
NA  
RA7  
BA2  
NA  
RA6  
GA7  
NA  
RA5  
GA6  
BA7  
GA1  
RA4  
GA5  
BA6  
GA0  
RA3  
GA4  
BA5  
RA1  
RA2  
GA3  
BA4  
RA0  
GA2  
RAIN1+  
BA3  
DEA  
NA  
RAIN1-  
RAIN2+  
RAIN2-  
RAIN3+  
RAIN3-  
BA1  
BA0  
Tcsq  
CKBIN-  
CKBIN+  
RBIN0+  
RBIN0-  
RB3  
GB4  
BB5  
RB1  
RB2  
GB3  
BB4  
RB0  
GB2  
BB3  
DEB  
NA  
RB7  
BB2  
RSV1  
BB1  
RB6  
RB5  
GB6  
BB7  
GB1  
RB4  
GB5  
BB6  
GB0  
RB3  
GB4  
BB5  
RB1  
RB2  
GB3  
BB4  
RB0  
GB2  
BB3  
DEB  
NA  
RBIN1+  
GB7  
NA  
RBIN1-  
RBIN2+  
RBIN2-  
RBIN3+  
RBIN3-  
BB0  
DE: Display Enable  
RSV1: Reserve (Fixed GND)  
NA: Not Available  
 
LD-14115-8  
4-2. Back light driving  
CN 1, 2, 3 (Upside)  
CN 4, 5, 6 (Downside)  
:
:
The module-side connector  
The user-side connector  
BHSR02VS01  
SM02BBHSS1TB  
Function  
(JST)  
(JST)  
Pin no. symbol  
I/O  
high  
low  
1
2
I
I
Power supply (High voltage side)  
Power supply (Low voltage side)  
1pin  
1pin  
CN1  
CN2  
CN3  
1pin  
TFT LCD  
1pin  
1pin  
CN4  
CN5  
CN6  
1pin  
5. Absolute Maximum Ratings  
Parameter  
Symbol Condition  
Ratings  
Unit  
Remark  
VI  
Ta=25℃  
Ta=25℃  
0.3 +3.6  
0 ~ +14.0  
25 ~ +60  
0 ~ +50  
Input voltage  
SELLVDS  
+12.0V supply voltage  
Storage temperature  
Vcc  
Tstg  
Note1】  
Operating temperature (Ambient) Topa  
Note1Humidity95%RH Max. ( Ta40)  
Maximum wet-bulb temperature at 39or less. ( Ta>40)  
No condensation.  
 
LD-14115-9  
6. Electrical Characteristics  
6-1. TFT-LCD panel driving  
Parameter  
Ta25℃  
Symbol Min.  
Typ. Max. Unit  
Remark  
Note1】  
Note2】  
Vcc  
Supply voltage  
Vcc  
Icc  
+11.4 +12.0 +12.6 V  
Current dissipation  
390  
600  
mA  
0
Permissive input ripple voltage  
Input voltage (Low)  
VRF  
VIL  
100 mVp-p  
+0.6  
+3.3  
500  
V
V
SELLVDS  
SELLVDS  
SELLVDS  
VI=GND  
VIH  
IIL  
Input voltage (High)  
+2.7  
μA  
Input current (Low)  
IIH  
μA  
Input current (High)  
100  
SELLVDS  
VI=Vcc  
VOL  
VOH  
Output voltage (Low)  
Output voltage (High)  
0.4  
V
V
BLON:IOL=-1mA  
BLON:IOH=1mA  
2.4  
Note1】  
1On-off sequences of Vcc and data  
Vcc  
Vcc  
11.4V  
11.4V  
0t160ms  
DE,CK ,Data  
DE,CK,Data  
0t210ms  
1.0V  
1.0V  
0t31s  
t4100ms  
t3  
t4  
t1  
t2  
Vcc  
2Dip conditions for supply voltage  
Vmin,Vth=11.4V, 9.6V  
1) Vth VccVmin  
td20ms  
2) VccVth  
Vth  
Vmin  
The LCD module shuts down.  
td  
RGB  
RGB  
RGB  
GS2  
RGB RGB  
GS254 GS255  
Note2Typical current situation : 256-gray-bar pattern  
Vcc=+12.0V  
....  
GS0 GS1  
The explanation of each gray scale ,GS,  
is described below section 8.  
 
LD-14115-10  
6-2. Back light driving  
The back light system is an edge-lighting type with six CCFTs (Cold Cathode Fluorescent Tube).  
The characteristics of the lamp are shown in the following table.  
The value mentioned below is at the case of one CCFT.  
CCFT Model NameKTBE26MSTFA424NE209Z3STANLEY.ELECTRIC.CO.,LTD)  
Parameter  
Lamp current range  
Lamp voltage  
Symbol  
IL  
Min.  
3.0  
Typ.  
6.0  
790  
4.7  
60  
Max.  
6.5  
Unit  
mArms  
Vrms  
W
Remark  
Note1】  
VL  
30  
70  
Ta=25℃  
Lamp power consumption  
Lamp frequency  
PL  
Note2】  
FL  
KHz  
Note3】  
Kick-off voltage  
Vs  
1,500 Vrms  
2,000 Vrms  
Ta=25℃【Note4】  
Ta=0℃【Note4】  
Lamp life time  
TL  
50,000  
Hour  
Note5】  
Note1A lamp can be light in the range of lamp current shown above.  
Maximum rating for current is measured by high frequency current measurement equipment  
connected to VLOW at circuit showed below.  
(Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.)  
Lamp frequency : 3070kHz  
Ambient temperature : 050℃  
CN1:1,2,3,4,5,6:  
1pin(Vhigh)  
Inverter  
CN1:1,2,3,4,5,6:  
Module  
2pin(Vlow)  
Note2Referential data per one CCFT by calculation ( IL × VL ) .  
The data doesn’t include loss at inverter .  
Note3Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and  
this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far  
as from module or use electronic shielding between inverter and module to avoid interference.  
Note4Kick-off voltage value is described as the index in the state of lamp only.  
The kick-off voltage is estimated to be risen up as approx. +200V in the state of module only, and the  
further rise up can be seen according to the assembling status of user cabinet. Please set the kick-off  
voltage of inverter to avoid the lighting failures in the state of operation. Please design the inverter so  
that its open output voltage can be connected for more than 1 second to startup. Otherwise, the lamp  
may not be turned on. But, please set as 100ms when the ambient luminance around the lamp is more  
than 1lux.  
Note5Lamp life time is defined as the time when either or occurs in the continuous operation under  
the condition of Ta=25and IL=6.0 mArms .  
Brightness becomes 50% of the original value under standard condition.  
Kick-off voltage at Ta=0exceeds maximum value,2000Vrms .  
Note》  
The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics  
of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting  
caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you  
confirm it, the module should be operated in the same condition as it is installed in your instrument.  
Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit  
or lamp voltage waveform detection circuit, which should have individual control of each lamp.  
In case one circuit without such individual control is connected to more than two lamps, excessive current may  
flow into one lamp when the other one is not in operation.  
Synchronize frequency and phase of two CCFT in the same connector.  
Otherwise it may exceed rated voltage of connector.  
 
LD-14115-11  
7. Timing characteristics of input signals  
7-1-1. Timing characteristics  
Parameter  
Symbol  
1/Tc  
Min.  
60.0  
–4  
Typ.  
81.0  
0
Max.  
85.0  
4
Unit  
MHz  
ns  
Remark  
Clock  
Frequency  
Skew  
Note1】  
Tcsq  
TH  
Data enable Horizontal period  
signal  
830  
1080  
13.3  
800  
1600  
clock  
µs  
10.0  
800  
Horizontal period (High)  
THd  
TV  
800  
2000  
clock  
line  
ms  
Note2】  
Vertical period  
1205  
12.1  
1200  
1250  
16.7  
1200  
Vertical period (High)  
TVd  
1200  
line  
Note1Lvds (A port)– Lvds (B port) phase difference  
Note2In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.  
TH  
THd  
DEA,DEB  
DA  
1
3
4
1
(RA,GA,BA)  
1599  
1599  
DB  
(RB,GB,BB)  
2
2
1600  
Tc  
1600  
1
2
1200  
DEA,DEB  
1199  
TVd  
TV  
DEA  
DEB  
Tcsq  
 
LD-14115-12  
7-2 Input Data Signals and Display Position on the screen  
Graphics and texts can be displayed on a 1600 × 3× 1200 dots panel with 16M colors by supplying  
48 bit data signal (8bit/color [256 gray scales] × 3 × 2 pixels).  
RA GA BA RB GB BB  
Two pixel-data are sampled at the same time.  
DA(1,1)  
DB(2,1)  
DARA0RA7, GA0GA7, BA0BA7  
DBRB0RB7, GB0GB7, BB0BB7  
DA(1,1) DB(2,1)  
DA(1,2) DB(2,2)  
DA(1,3)  
DA(3,1)  
DB(1600,1)  
R G B  
DA(1,1200)  
DB(1600,1200)  
Display position of input dataH,V)  
 
LD-14115-13  
8. Input Signals, Basic Display Colors and Gray Scale of Each Color  
Data signal  
Colors & Gray RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 GA0 GA1 GA2 GA3 GA4 GA5 GA6 GA7 BA0 BA1 BA2 BA3 BA4 BA5 BA6 BA7  
Gray scale Scale RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 GB0 GB1 GB2 GB3 GB4 GB5 GB6 GB7 BB0 BB1 BB2 BB3 BB4 BB5 BB6 BB7  
Black  
Blue  
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Green  
Cyan  
Red  
Magenta  
Yellow  
White  
Black  
GS0  
GS1  
GS2  
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker  
Brighter GS250  
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
GS251  
GS252  
Red  
Black  
GS0  
GS1  
GS2  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker  
Brighter GS250  
GS251  
Green GS252  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Black  
GS0  
GS1  
GS2  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker  
Brighter GS250  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
GS251  
GS252  
Blue  
0 : Low level voltage,  
1 : High level voltage.  
Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of  
total 48 bit data signals, the 16-million-color display can be achieved on the screen.  
 
LD-14115-14  
9. Optical Characteristics  
Parameter  
Ta=25, Vcc =+12V  
Remark  
Symbol  
θ11  
θ12  
θ21,θ22  
CR  
τd  
Condition  
Min.  
70  
Typ.  
85  
Max.  
Unit  
Deg.  
Deg  
CR10  
Viewing  
Vertical  
Note1,4】  
Angle range  
70  
85  
Horizontal  
70  
85  
Deg.  
θ=0°  
Contrast ratio  
350  
5
Note2,4】  
ms  
ms  
Response  
Time  
Rise  
25  
Note3,4】  
τr  
Decay  
20  
50  
0.283  
0.313  
0.343  
Chromaticity of  
Wx  
Note4】  
0.329  
white  
Chromaticity of  
red  
Wy  
0.299  
0.608  
0.309  
0.250  
0.570  
0.114  
0.057  
0.359  
0.668  
0.369  
0.310  
0.630  
0.174  
0.117  
Rx  
0.638  
0.339  
0.280  
0.600  
0.144  
0.087  
Ry  
Chromaticity of  
green  
Gx  
Gy  
Chromaticity of  
blue  
Bx  
By  
Luminance of white  
YL  
cd/m2  
IL=6.0mA rms  
Note4】  
180  
220  
δw  
White Uniformity  
1.25  
Note5】  
The measurement shall be executed 30 minutes after lighting at rating.  
The optical characteristics shall be measured in a dark room or equivalent state with the method  
shown in Fig.2 below.  
Photodetector  
Contrast ratio/Response Time(BM-5A)  
Luminance(BM-7)  
Chromaticity(SR-1)  
Photodetector(EZ-CONTRAST)  
400mm  
Field=2°  
Center of screen(θ=0°)  
Center of screen(θ=0°)  
TFT-LCD-Module  
TFT-LCD-Module  
Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity  
measurement method  
Fig2-1 Viewing angle measurement method  
Fig2 Optical characteristics measurement method  
 
LD-14115-15  
Note1Definitions of viewing angle range:  
Note2Definition of contrast ratio:  
The contrast ratio is defined as the following.  
Luminance (brightness) with all pixels white  
Luminance (brightness) with all pixels black  
Contrast Ratio (CR) =  
Note3Definition of response time:  
The response time is defined as the following figure and shall be measured by  
switching the input signal for "black" and "white".  
Note4This shall be measured at center of the screen.  
Note5Definition of white uniformity:  
White uniformity is defined as the  
following with five measurements  
(AE).  
400  
800  
1200 pixel  
A
B
D
E
300  
600  
C
900  
pixel  
Maximum Luminance of five points (brightness)  
Minimum Luminance of five points (brightness)  
δw=  
 
LD-14115-16  
10. Handling Precautions  
a) Be sure to turn off the power supply when inserting or disconnecting the cable.  
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or  
twist.  
c) Since the front polarize is easily damaged, pay attention not to scratch it.  
d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.  
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.  
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with  
care.  
g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into  
consideration when handling.  
h) Make sure the mounting holes of the module are grounded sufficiently. Take electro-magnetic interference  
(EMI) into consideration.  
i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any  
stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs  
may be damaged.  
j) Observe all other precautionary requirements in handling components.  
k) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity  
issue , functional defect, etc. So, please avoid such design.  
l) If the stress is applied onto the panel under operating conditions, display defects such as black dots may  
occur. So, do not press the display with fingers.  
To recover this defect, turn off the power supply and restart after several seconds.  
11. Packing form  
a) Piling number of cartons : maximum 8 cartons  
b) Packing quantity in one carton : 2 module  
c) Carton size : 592mm(W) × 486mm(H) × 215(D)  
d) Total mass of one carton filled with full modules : 10.5kg  
e) Packing form is shown in Fig.3  
 
LD-14115-17  
12Reliability test items  
No. Test item  
Conditions  
Ta=60℃  
Ta=-25℃  
240h  
240h  
1
2
3
High temperature storage test  
Low temperature storage test  
High temperature  
Ta=40; 95%RH 240h  
& high humidity operation test  
High temperature operation test  
(No condensation)  
Ta=50℃  
(The panel temp. must be less than 60)  
Ta=0240H  
240h  
4
5
6
Low temperature operation test  
Vibration test  
Frequency : 1057Hz/Vibration width (one side) : 0.075mm  
: 58500Hz/Gravity : 9.8m/s2  
Sweep time : 11 minutes  
(non- operating)  
Test period : 3 hours  
(1 hour for each direction of X,Y,Z)  
Max. gravity : 490m/s2  
7
Shock test  
(non- operating)  
Pulse width : 11ms, sine wave  
Direction : ±X, ±Y, ±Z,  
once for each direction.  
Result Evaluation Criteria】  
Under the display quality test conditions with normal operation state, these shall be no change  
which may affect practical display function.  
 
LD-14115-18  
13Others  
1) Lot No. and indication Bar Code Label:  
SHARP  
LQ201U1LW01  
How to express Lot No.  
Model No.  
A production year  
(the last figures of  
the Christian Era)  
Bar Code(Lot No.)  
Lot No.  
Serial No.  
23 XXXXXX  
MADE IN JAPAN  
A production month (1~9,X,Y,Z)  
2) Packing Label  
  ① Model No. (LQ201U1LW01)  ② Lot No. (Date)  ③ Quantity  
社内品番(4S)LQ201U1LW01  
Bar Code(①)  
LotNO.  (1T)2002.03.01  
Bar Code(②)  
Quantity(Q)    2  pcs  
Bar Code(③)  
ユーザ品番   :  
シャープ物流用ラベルです。  
3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.  
If adjusted value is changed, the specification may not be satisfied.  
4) Disassembling the module can cause permanent damage and should be strictly avoided.  
5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.  
6) The chemical compound that causes the destruction of ozone layer is not being used.  
7) Warning of mercury and material information of LPG(Light Pipe Guide) are labeled on the back of the  
module.  
MATERIAL INFORMATION  
>PLASTIC LIGHT GUIDE:PMMA<  
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL  
CONTAINS A SMALL AMOUNT OF MERCURY,PLEASE FOLLOW  
LOCAL ORDINANCES OR REGULATION FOR DISPOSAL  
当該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自  
冶体の条例、または、規則に従って廃棄ください。  
8) When any question or issue occurs, it shall be solved by mutual discussion.  
 
LD-14115-19  
14Carton storage condition  
Temperature  
0to 40℃  
Humidity  
95%RH or less  
Reference condition : 20to 35, 85%RH or less (summer)  
5to 15, 85%RH or less (winter)  
:
the total storage time (40,95%RH) : 240H or less  
Sunlight  
Be sure to shelter a product from the direct sunlight.  
Atmosphere  
Harmful gas, such as acid and alkali which bites electronic components and/or  
wires, must not be detected.  
Notes  
Be sure to put cartons on palette or base, don’t put it on floor, and store them with  
removing from wall.  
Please take care of ventilation in storehouse and around cartons, and control  
changing temperature is within limits of natural environment.  
1 year  
Storage period  
 
LD -14115-20  
 
LD -14115-21  
 
LD -14115-22  
 
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited  
Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.  
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,  
for any incidental or consequential economic or property damage.  
NORTH AMERICA  
EUROPE  
JAPAN  
SHARP Corporation  
SHARP Microelectronics of the Americas  
5700 NW Pacific Rim Blvd.  
Camas, WA 98607, U.S.A.  
Phone: (1) 360-834-2500  
Fax: (1) 360-834-8903  
SHARP Microelectronics Europe  
Division of Sharp Electronics (Europe) GmbH  
Sonninstrasse 3  
20097 Hamburg, Germany  
Phone: (49) 40-2376-2286  
Fax: (49) 40-2376-2232  
Electronic Components & Devices  
22-22 Nagaike-cho, Abeno-Ku  
Osaka 545-8522, Japan  
Phone: (81) 6-6621-1221  
Fax: (81) 6117-725300/6117-725301  
Fast Info: (1) 800-833-9437  
TAIWAN  
SINGAPORE  
KOREA  
SHARP Electronic Components  
(Korea) Corporation  
RM 501 Geosung B/D, 541  
Dohwa-dong, Mapo-ku  
Seoul 121-701, Korea  
SHARP Electronic Components  
(Taiwan) Corporation  
8F-A, No. 16, Sec. 4, Nanking E. Rd.  
Taipei, Taiwan, Republic of China  
Phone: (886) 2-2577-7341  
SHARP Electronics (Singapore) PTE., Ltd.  
438A, Alexandra Road, #05-01/02  
Alexandra Technopark,  
Singapore 119967  
Phone: (65) 271-3566  
Phone: (82) 2-711-5813 ~ 8  
Fax: (82) 2-711-5819  
Fax: (886) 2-2577-7326/2-2577-7328  
Fax: (65) 271-3855  
CHINA  
HONG KONG  
SHARP Microelectronics of China  
(Shanghai) Co., Ltd.  
SHARP-ROXY (Hong Kong) Ltd.  
3rd Business Division,  
28 Xin Jin Qiao Road King Tower 16F  
Pudong Shanghai, 201206 P.R. China  
Phone: (86) 21-5854-7710/21-5834-6056  
Fax: (86) 21-5854-4340/21-5834-6057  
Head Office:  
17/F, Admiralty Centre, Tower 1  
18 Harcourt Road, Hong Kong  
Phone: (852) 28229311  
Fax: (852) 28660779  
No. 360, Bashen Road,  
Xin Development Bldg. 22  
Shenzhen Representative Office:  
Room 13B1, Tower C,  
Waigaoqiao Free Trade Zone Shanghai  
200131 P.R. China  
Electronics Science & Technology Building  
Shen Nan Zhong Road  
Shenzhen, P.R. China  
Phone: (86) 755-3273731  
Fax: (86) 755-3273735  
 

Shure Headphones M75E 95C 7 User Manual
Shure Microphone 888TT User Manual
Soleus Air Dehumidifier SG DEH 70 2 DP2 70 03 User Manual
Sony Camcorder NEX VG10 User Manual
Sony Home Theater System DAV DX155 User Manual
Sony Satellite TV System DST HD500 User Manual
Sony TV Mount SU W200 User Manual
Sony VCR SLV 777HF User Manual
Sterling Plumbing Product E045000 User Manual
Sunbeam Egg Cooker EC1300 User Manual