SHARP MICROWAVE TRIM KIT
MODEL NO. RKJ39S
WARRANTY
Consumer Electronic Products
PART IDENTIFICATION SHEET
4
Congratulations on Your Purchase!
This Sharp product is warranted against faults in materials and manufacture for a period of twelve (12) months
from the date of original purchase.
1. FASCIA ASSEMBLY
2. 4 off PLASTIC FEMALE CLIPS
3. BASE ASSEMBLY
4. 8 off 6 GAUGE SCREWS
5. 2 off BUTTON HEAD SCREWS
2
If service is required during the warranty period, please contact your nearest Sharp Approved Service Cen-
tre. These repairs would be carried out at no charge to the owner, subject to the conditions specified herein.
The owner is responsible for any transportation and insurance costs if the product has to be returned for
repair.
1
This warranty does not extend to accessories or defects or injuries caused by or resulting from causes not
attributable to faulty parts or the manufacture of the product, including but not limited to, defect or injury
caused by or resulting from misuse, abuse, neglect, accidental damage, improper voltage, liquid spillage,
vermin infestation, software, or any alterations made to the product which are not authorised by Sharp.
3
Please retain your sales documentation, as this should be produced to validate a warranty claim.
5
This warranty is in addition to and in no way limits, varies or excludes any express and implied rights and
remedies under any relevant legislation in the country of sale.
“The RKJ39S is designed for the R395YW and R395NS. Should you wish to use it for
the R395FS please contact Sharp Customer Care Australia on 1300 135 022
(for Sharp Customer Care New Zealand contact 09 920 4147) for an alternate base”
IMPORTANT
DO NOT RETURN THIS DOCUMENT TO SHARP
CAUTION
For your reference, please enter the particulars of your purchase below and retain, with your purchase
documentation.
Model No.
Serial No.
Date of Purchase
Retailer
1. Read and follow all of the instructions completely.
2. The Sharp Built-in Trim Kit must be installed in accordance with the full set of instructions listed and meet
the regulations laid down by electrical authorities, building regulations and the requirements of state and local
government authorities.
3. The microwave oven must be unplugged before installation of the Sharp Built-in Kit.
4. For safe use of the microwave oven, DO NOT modify or alter any part of this kit.
5. The kitchen cabinetry that houses the microwave oven must be constructed to allow the microwave oven to
operate to Australian Standards 3350.1-2002, 60335.1, 3350.2.25-2001 and 60335.2.25.
FOR LOCATION ENQUIRIES WITHIN
FOR PRODUCTS PURCHASED IN
AUSTRALIA
REGARDING YOUR
LOCAL
NEW ZEALAND
CARE AND CLEANING
CONTACT YOUR SELLING DEALER/RETAILER
OR CALL
Use a mild stainless steel cleaner applied with a soft damp cloth. Wipe in the stainless steel grain direction. DO
NOT USE CAUSTIC CLEANERS, ABRASIVE OR HARSH CLEANERS OR SCOURING PADS.
SHARP APPROVED SERVICE CENTRE
CALL THE
SHARP CUSTOMER SERVICES
TELEPHONE: 09 573 0111
TRIM KIT SPECIFICATIONS
SHARP SERVICE REFERRAL CENTRE
FACSIMILE: 09 573 0113
or contact our web site
LOCAL CALL 1 300 135 022
Cavity Dimensions
Internal Width
External Front Height
Depth
Overall Kit Dimensions;
or visit our website
600mm
381mm
500mm (minimum)
Width
Height
Depth
596mm
380mm
22mm (Fascia)
SHARP CORPORATION OF AUSTRALIA PTY. LIMITED
ABN 40 003 039 405
SHARP CORPORATION OF NEW ZEALAND LIMITED
59 Hugo Johnston Drive
1 Huntingwood Drive Blacktown NSW 2148
Penrose, Auckland
Cabinetry Ventilation
An opening on the upper cavity panel must be cut for air circulation. This opening should be placed at the
rear– minimum 600mm x 100mm.
IMPORTANT NOTICE: This warranty applies only to products sold in Australia & New Zealand.
|