S3251
S3251_11_ENG_IB_101117.indd
1
10-11-17 1:58 PM
11. DO NOT unplug by pulling on
power cord. To unplug, grasp
the plug not the power cord.
Do not use extension cords or
outlets with inadequate current
carrying capacity.
21. Extreme caution should be
exercised when using this
appliance to clean stairs.
22. Never use steam mop without
micro-fiber pad attached.
23. Keep your work area well lit.
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
24. Store steam mop indoors in a
cool, dry place.
25. To avoid circuit overload, do
not operate another appliance
on the same socket (circuit) as
the steam cleaner.
13. DO NOT put hands or feet
under the steam mop. Unit
gets very hot.
14. Use ONLY on flat, stable
horizontal surfaces. Do not use
on walls, counters, windows,
chairs or tables.
26. If an extension cord is
absolutely necessary, an
extension cord rated a
minimum of 15 ampere, 14
gage cord should be used.
Cords rated for less amperage
may overheat. Care should be
taken to arrange cord so that
it cannot be pulled or tripped
over.
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or
other delicate, steam sensitive
materials.
16. DO NOT add cleaning
solutions, scented perfumes,
oils or any other chemicals to
the water used in this appliance
as this may damage the unit
or make it unsafe for use. If
you live in a hard water area,
we recommend using distilled
water in your steam mop.
27. DO NOT leave unattended
when the system is connected
to a power supply or electrical
outlet. Turn off all controls
before unplugging the unit.
28 DO NOT store unit with damp
or wet micro-fiber cleaning
pad attached. Never leave the
steam mop in one spot on any
surface for any period of time
with a damp or wet micro-
17. When in use, NEVER turn
the appliance over or on its
side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS
OR PLANTS.
fiber cleaning pad attached as
this will damage your floors
18. Carefully remove the micro-
fiber pad immediately after you
have unplugged and allowed
the product to cool.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand
high heat. Do not use on
19. When cleaning the steam mop,
unplug the power cord from
the electrical outlet and clean
with a dry or damp cloth. Do
not pour water or use alcohol,
benzene or paint thinner on the
unit.
unsealed wood or unglazed
ceramic floors. On surfaces
that have been treated with
wax or some no wax floors,
the sheen may be removed
by the heat and steam action.
It is always recommended
to test an isolated area of
the surface to be cleaned
before proceeding. We also
recommend that you check the
use and care instructions from
the floor manufacturer.
20 To reduce the risk of fire,
DO NOT use a flammable or
combustible liquid to clean a
floor.
S3251_11_ENG_IB_101117.indd
3
10-11-17 1:58 PM
Quick Start
fig. 3
fig. 2
fig. 1
ASSEMBLE
FILL
1
Fit together the extension tubes
as shown in the illustration.
(fig. 1)
3
Remove the cap to fill the
water tank. Use the filling flask
and funnel to fill the tank with
water to the “MAX” fill line.
Replace the water tank cap.
(fig. 3)
2
Place the micro-fiber cleaning
pad underneath the mop head,
with quick fastener strips facing
up. Simply press the mop to the
pad to attach it. (fig. 2)
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
4
10-11-17 1:58 PM
QUICK TIP:
For easier
pushing
and pulling,
extend the
handle length.
fig. 4
STEAM CLEANING
NOTE: Do not leave your
Steam Mop unattended
during use.
4 For your comfort, you can adjust
the height of the mop. Just lift
the latch on the tube 90 degrees
to the open position. Holding the
handle, extend the tube to the
desired height and then close the
latch to the locked position.
IMPORTANT: Never leave
the steam mop in one spot
for any period of time with
a damp or wet micro-fiber
pocket attached as this will
damage your floors.
5
Plug in the mop. Wait 30
seconds for the unit to heat up
and the steam to be ready.
Push the handle toward the
mop head in a pumping motion.
Customize steam output by slow
or fast mopping with a forward
and backward motion. (fig. 4)
S3251_11_ENG_IB_101117.indd
5
10-11-17 1:58 PM
This manual covers model number:
S3251 11
TECHNICAL SPECIFICATIONS
Voltage:
120V., 60Hz.
1550 Watts
Power:
Water
Capacity:
250 ml (8 oz.)
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
6
10-11-17 1:58 PM
Contents
GETTING STARTED.................................................................2
USING YOUR STEAM MOP...................................................6
STORAGE AND CARE OF YOUR STEAM MOP ............8
TROUBLESHOOTING ...........................................................10
WARRANTY AND REGISTRATION...................................13
Thank you for
purchasing
the Shark®
™
Light & Easy
Steam Mop.
S3251_11_ENG_IB_101117.indd
1
10-11-17 1:58 PM
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you
buy them, so you get a quality
Shark® Light & Easy™ Steam Mop.
a
b
c
b
e
d
f
fig. 1
FIRST THINGS FIRST, YOU NEED TO
KNOW WHAT’S IN THE BOX YOU
JUST OPENED:
ASSEMBLY
1
Remove all the parts from the
package. Verify all the listed parts
are included.
a Upper Extension Tube
b Lower Extension Tube (Telescopic)
c Steam Mop Base
2 Slide the upper extension tube
(the tube with the handle) into the
lower extension tube (the short
tube). Push the two extension tubes
together in until you hear it click into
place. (fig. 1)
d 2 All-Purpose Cleaning Pads
e Filling Flask
f Funnel
2
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
2
10-11-17 1:58 PM
English
fig. 3
fig. 2
3 Insert the assembled handle piece
into the steam mop base. Push the
tube base together until you hear a
click. (fig. 2)
IMPORTANT: Never use the Light &
Easy™ Steam Mop without attaching
a micro-fiber cleaning pad to avoid
damage to your floor and mop.
4 For your comfort, you can adjust the
height of the mop. Just lift the latch
on the tube 90 degrees to the open
position. Holding the handle, extend
the tube to the desired height and
then close the latch to the locked
position. (fig. 3)
IMPORTANT: Do not use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by the
heat and steam action. It is always
recommended to test an isolated area
of the surface to be cleaned before
proceeding. We recommend that you
check the use and care instructions
from the floor manufacturer.
QUICK TIP: For easier pushing and
pulling, extend the handle length.
3
S3251_11_ENG_IB_101117.indd
3
10-11-17 1:58 PM
Getting Started
Your micro-fiber cleaning pads
should be replaced every 3
months to maximize cleaning
performance.
fig. 1
ATTACHING THE MICRO-FIBER PAD
Replacement micro-fiber pads are
by calling 1-800-798-7398.
1
Place the micro-fiber cleaning pad
on the floor with the quick fastener
strips facing up. Place the Light &
Easy™ Steam Mop on the top of the
pad to attach. (fig. 1)
IMPORTANT: Only add water to the
tank. Chemicals or cleaning solutions
may be unsafe or cause damage.
IMPORTANT: Please wait 3-5 minutes
for your Light & Easy™ Steam Mop to
cool off before removing the micro-
fiber pad.
4
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
4
10-11-17 1:58 PM
English
Calcium and mineral deposits
can build up and impact the
performance of your steam mop
over time. To extend the life of
your product we recommend that
you use distilled water or Shark®’s
Water Filtration Bottle. Visit www.
sharkclean.com to order.
fig. 2
fig. 3
FILLING THE WATER TANK
2 A filling flask and funnel are included
with your Light & Easy™ Steam Mop
to make filling the water tank easy.
Fill the flask with water and use the
funnel to pour it into the tank. Keep
the water level under the MAX’ fill
line.
IMPORTANT: Unplug the Light &
Easy™ Steam Mop before filling the
water tank with water. (fig. 2)
1
Remove the water tank cap by
turning it counter-clockwise to the
unlocked position. (fig. 3)
3 Replace the water tank cap and turn
it clockwise to the locked position.
5
S3251_11_ENG_IB_101117.indd
5
10-11-17 1:58 PM
Using Your Light & Easy™ Steam Mop
When you use your steam mop for the
first time or if you have not used the unit
in awhile, it may take a minute or two
for the water to travel through the pump
and into the heater to create steam. Get
it started by pumping the handle a few
times. If you have waited a few minutes
and you still do not see any steam,
reference the troubleshooting section
on page 10.
fig. 1
fig. 2
fig. 3
IMPORTANT: Your steam mop needs
water to make steam! Never use your
steam mop without water in the tank.
1
Pull and twist the quick release
cord holder to unwrap the power
cord completely. (fig. 1) Plug into
a 120-volt electrical outlet. (fig. 2)
The “On” light will turn blue. If the
light does not turn on, reference the
troubleshooting section on page 10.
(fig. 3)
Sweep or vacuum your floors prior
to cleaning with your Light & Easy™
Steam Mop.
great quick cleaning products to
complement your Light & Easy™
Steam Mop, such as the Shark®
Navigator.
6
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
6
10-11-17 1:58 PM
English
™
If your Light & Easy Steam
Mop stops steaming, it could
be out of water. Unplug the
power cord from the electrical
outlet and refill the water tank
at anytime.
fig. 4
fig. 5
2 Wait 30 seconds for the boiler to
heat the water. Pump the handle
a few times to prime the pump,
activate steam and moisten the
micro-fiber pad. (fig. 4)
3 Mop with a forward and backward
motion to customize steam output
automatically. (fig. 5)
IMPORTANT: Never leave the Light &
Easy™ Steam Mop with a damp/wet
micro-fiber pad on any floor surface
for any amount of time as this may
damage the floor.
7
S3251_11_ENG_IB_101117.indd
7
10-11-17 1:58 PM
Care of Your Light & Easy™ Steam Mop
fig. 1
fig.2
fig.3
AFTER USE AND STORAGE
4 To store the cooled Shark® Light &
Easy™ Steam Mop, hang on a large
hook. (fig. 3)
1
When you have finished using the
Light & Easy™ Steam Mop, unplug
the cord from the outlet and place
the mop into the upright position
(fig. 1) and let the unit cool 3-5
minutes. Release steam by pumping
the handle several times.
NOTE: If you want to store the
Light & Easy™ Steam Mop standing
upright, make sure it is leaning
against a wall for added support and
safety. Always store your Shark®
Light & Easy™ Steam Mop with the
micro-fiber cleaning pad removed.
Store away from children and high
traffic areas.
2 Carefully separate micro-fiber
cleaning pad from steam mop,
avoiding contact with the hot pad or
dirt. (fig. 2)
3 Empty the water tank before storage.
Remove the water tank cap and
empty the tank over a sink. Replace
the water cap.
8
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd
8
10-11-17 1:58 PM
English
Care of Your Light & Easy™ Steam Mop
fig. 4
fig. 5
CARE OF YOUR MICRO-FIBER
CLEANING PAD
ORDERING REPLACEMENT PARTS
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or call
1-800-798-7398.
1
Wash pads in warm water. Wash
separately from other laundry. Only
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting. (fig. 4)
NOTE: Some parts may be available
at your local retailer. Contact customer
service for any other servicing.
2 If there are loose threads on the
pad carefully cut the threads with
scissors. Do not pull on them or cut
at the base. (fig. 5)
IMPORTANT: The micro-fiber
cleaning pad may be very hot
from the steam. Use caution when
removing. Let the unit cool for 3-5
minutes first before removing.
9
S3251_11_ENG_IB_101117.indd
9
10-11-17 1:58 PM
Trouble Shooting
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Your steam-mop should be securely plugged into a
120V AC electrical outlet only.
The Light & Easy™
Steam Mop will
not turn-on.
Check your fuse or breaker.
If your unit still does not work, call 1-800-798-7398.
Light & Easy™
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your
steam mop following instructions on page 5.
Light & Easy™
Steam Mop leaves
water on the floor.
Is your micro-fiber cleaning pad too wet? Unplug your
steam mop and change the micro-fiber cleaning pad.
Do not leave your steam-mop on the floor with a damp or
wet cleaning pad.
Light & Easy™
Steam Mop left
white spot on
the floor.
Do you have hard water? If you do, you might want to
switch to distilled water.
Make sure the water is securely on the water tank.
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent, then the
pad may have residual detergent left on it. Wash it again
with liquid detergent.
If you are cleaning in a kitchen area where there might be a
build-up of grease, use a de-greasing agent such as an all-
purpose cleaner or dish soap and paper towels to clean the
area first.
Floors are cloudy,
streaky or spotty
after steaming.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to
switch to distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed.
Make sure the steam pad is attached correctly.
Light & Easy™
Steam Mop is
hard to push.
Check to see if the cleaning pad is excessively dirty.
Replace if the pad is too dirty or wet.
10
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd 10
10-11-17 1:58 PM
Notes
12
TOLL FREE: 1-800-798-7398
S3251_11_ENG_IB_101117.indd 12
10-11-17 1:58 PM
English
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and a check payable to EURO-PRO
Operating LLC in the amount of $ 9.95 to cover the cost of return shipping and handling must be
included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………............
ADDRESS: ………………………………………………………………………………………………...............
S3251 11
DATE OF PURCHASE: …………………….. MODEL: ………………...................................
NAME AND ADDRESS OF STORE: …………………………………………………………………..
13
S3251_11_ENG_IB_101117.indd 13
10-11-17 1:58 PM
U.S.:
EURO-PRO Operating LLC
Newton, MA 02459
Canada: EURO-PRO Operating LLC
4400 Bois Franc
Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
COPYRIGHT© EURO-PRO OPERATING LLC 2010
PRINTED IN CHINA
S3251.E.101117
Illustrations may differ from actual product.
S3251_11_ENG_IB_101117.indd 14
10-11-17 1:58 PM
|