SK 500
Instructions for use
Contents
Selecting the frequencies to be stored
Error checklist ................................................................ 24
Polar diagrams and frequency response curves
3
The SK 500 G2 bodypack
transmitter
The SK 500 G2 bodypack transmitter is part of the
evolution wireless series ew 500 G2. With this series,
Sennheiser offers high-quality state-of-the-art RF
transmission systems with a high level of operational
reliability and ease of use. Transmitters and receivers
permit wireless transmission with studio-quality sound.
The excellent transmission reliability of the ew 500 G2
series is based on the use of
y further optimized PLL synthesizer and microprocessor
technology,
y the HDX noise reduction system,
y and the pilot tone squelch control.
The channel bank system
The transmitter is available in five UHF frequency ranges
with 1440 transmission frequencies per frequency range.
Please note: Frequency usage is different for each country.
Your Sennheiser agent will have all the necessary details on
the available legal frequencies for your area.
Range A:
Range B:
Range C:
Range D:
Range E:
518 to 554 MHz
626 to 662 MHz
740 to 776 MHz
786 to 822 MHz
830 to 866 MHz
The transmitter has nine channel banks with up to 20
switchable channels each.
channel 1
channel 2
preset frequency
preset frequency
channel bank 1...8
preset frequency
channel 20
channel 1
channel 2
freely selectable frequency
freely selectable frequency
channel bank U
freely selectable frequency
channel 20
Each of the channels in the channel banks “1” to “8” has
been factory-preset to a transmission frequency (see
enclosed frequency table). These transmission frequencies
cannot be changed but have been preset so that e.g.
country-specific regulations on frequency usage are taken
into account.
The channel bank “U” (user bank) allows you to store
frequencies that are freely selectable.
4
Safety instructions
Never open an electronic unit! If units are opened by
customers in breach of this instruction, the warranty
becomes null and void.
Use the unit in dry rooms only.
Use a damp cloth for cleaning the unit. Do not use any
cleansing agents or solvents.
Delivery includes
The packaging contains the following items:
y 1 SK 500 G2 bodypack transmitter
y 2 batteries
y 1 BPP 1 bodypack pouch
y 1 Instructions for use
5
Areas of application
The transmitter can be combined with receivers of the
ew 500 G2 series (EM 500 G2 rack-mount receiver or
EK 500 G2 bodypack receiver). The receivers are available in
the same five UHF frequency ranges and are equipped with
the same channel bank system with factory-preset
frequencies. An advantage of the factory-preset
frequencies is that
y a transmission system is ready for immediate use after
switch-on,
y several transmission systems can be operated
simultaneously on the preset frequencies without
causing intermodulation interference.
Together with a matching receiver and a microphone or an
instrument cable, the transmitter is suitable for the
following areas of applications:
Transmitter Receiver (to be
ordered separately)
Area of
application
EM 500 G2
y Theater
y Presentation
y Sports (aerobic)
y Vocals
SK 500 G2
y Using instruments
wirelessly
y Speech
EK 500 G2
y Vocals
y Presentation
y Camera-mounted
applications
Four different microphones and an instrument cable are
available for the transmitter:
Microphone/ Type
instrument
cable
Pick-up
pattern
Area of
application
y Theater
ME 2 clip-on condenser omni-
y Presentation
(omni-
microphone
directional
directional)
professional use:
MKE 2-ew
clip-on
microphone
condenser omni-
directional
y Theater
y Presentation
y Sports
(aerobic)
y Vocals
ME 3
headmic
condenser super-
cardioid
y Theater
y Presentation
(high feedback
rejection)
ME 4 clip-on condenser cardioid
microphone
y Using
instruments
wirelessly
CI 1
instrument
cable
–
6
The operating controls
·
»
³
Ƹ
¹
¿
´
²
¶
¸
º
¾
µ
³ Microphone/line input (MIC/LINE),
3.5 mm jack socket
· Antenna
» Red LED for operation and
battery status indication (ON/LOW BAT)
¿ Yellow LED for audio peak (AF PEAK)
´ Charging contacts
² SET button
¶ ̄/̆ rocker button (UP/DOWN)
º Battery compartment
¾ Battery compartment cover
µ Unlocking button
¸ ON/OFF button
(serves as the ESC (cancel) key in the
operating menu)
¹ LC display
Ƹ MUTE switch
7
Indications and displays
LC display panel
ባ
ቤ
ቢ
ቩ
ብ
ቦ
ቧ
ቨ
ቢ Alphanumeric display
ባ “B.CH“ – appears when the channel bank and
the channel number are displayed
ቤ “MHz“ – appears when the frequency is displayed
ብ 4-step battery status display
ቦ Lock mode icon
(lock mode is activated)
ቧ “PILOT” display
(pilot tone transmission is activated)
ቨ “MUTE” display
(audio input is muted)
ቩ 7-step level display for audio signal “AF”
Operation and battery status indication
The red LED (LOW BAT/ON) ꢀ provides information on the
current operating state of the transmitter:
»
ብ
Red LED lit up:
The transmitter is switched on and
the capacity of the batteries/
BA 2015 accupack is sufficient.
Red LED flashing:
The batteries are/the BA 2015
accupack is going flat (LOW BAT)!
In addition, the 4-step battery status display ብ on the
display panel provides information on the remaining
battery/BA 2015 accupack capacity:
3 segments:
2 segments:
1 segment:
capacity approx. 100 %
capacity approx. 70 %
capacity approx. 30 %
Battery icon flashing: LOW BAT
8
“MUTE” display
The “MUTE” display ቨ appears on the display panel when
the transmitter is muted (see “Muting the transmitter” on
ቨ
Modulation display
The level display for audio signal “AF” ቩ shows the
modulation of the transmitter.
When the transmitter’s audio input level is excessively
high, the level display for audio signal “AF” ቩ shows full
deflection for the duration of the overmodulation. In
addition, the yellow LED (AF PEAK) ꢁ at the front of the
transmitter lights up.
¿
ቩ
“PILOT” display
The “PILOT” display ቧ appears on the display panel when
the pilot tone transmission is activated (see “Activating/
Display backlighting
After pressing a button, the display remains backlit for
approx. 15 seconds.
9
Preparing the bodypack
transmitter for use
Inserting and replacing the batteries
For powering the transmitter, two 1.5 V AA size batteries
are required.
̈ Press the two unlocking buttons µ and open the
battery compartment cover ᕩ.
µ
¾
ᕩ
´
̈ Insert the two batteries as shown above. Please observe
correct polarity when inserting the batteries.
̈ Close the battery compartment. The battery
compartment cover ᕩ locks into place with an audible
click.
Inserting and charging the accupack
The transmitter can also be powered via the rechargeable
Sennheiser BA 2015 accupack. Insert the accupack into the
battery compartment as described above.
The transmitter has two charging contacts ᕥ and a sensing
contact on its short sides. The accupack can be recharged
while remaining in the transmitter. Insert the transmitter
into the L 2015 charger (see operating manual of the
L 2015 charger).
Note:
For accupack operation of the transmitter, only use the
BA 2015 accupack in order to ensure optimum
operational reliability. For charging the accupack, only
use the L 2015 charger. Both the accupack and the
charger are available as accessories.
The accupack is fitted with an integrated sensor which is
– via a third contact – monitored by the electronics of
the transmitter and the charger. The sensor is necessary
for the following control purposes:
10
y The taking into account of the different voltage
characteristics of primary cells (batteries) and
accupacks. The battery status indications on the
displays, the transmission of transmitter battery
status information to the rack-mount receivers and
the switch-off thresholds at the end of the operating
time are corrected correspondingly. Due to the
missing sensor, individual rechargeable battery cells
will not be identified as accupacks.
y The monitoring of the accupack temperature during
charging in the L 2015 charger.
y The prevention of improper charging of inserted
primary cells (batteries). Due to the missing sensor,
individual rechargeable battery cells will also not be
charged in the L 2015 charger.
Connecting the microphone/line cable
The microphone/line input is designed for the connection of
both condenser microphones and instruments (e.g.
guitars). DC powering of the condenser microphones is via
the microphone/line input.
̈ Connect the 3.5 mm jack plug ƹ from the microphone/
line cable to the 3.5 mm jack socket (MIC/LINE) ᕡ.
ƹ
ƺ
³
̈ Lock the 3.5 mm jack plug by screwing down the
coupling ring ƺ.
̈ Via the operating menu, adjust the sensitivity of the
microphone/line input (MIC/LINE) (see “Adjusting the
Attaching the microphones
Use the microphone clips ꢂ to attach the ME 2 or ME 4 clip-
on microphones to clothing (e.g. tie, lapel).
ꢂ
̈ Adjust the ME 3 headmic so that a comfortable and
secure fit is ensured.
11
Positioning the microphones
The ME and ME microphones are directional
3
4
microphones, i.e. their sound inlet should always be
directed towards the sound source (e.g. mouth).
The ME 2 with omni-directional pick-up pattern picks up
sound equally from all directions. It is the best choice if
movements of the speaker’s head have to be compensated
for. However, it should be attached as close as possible to
the sound source.
Adjust the sensitivity correctly for all microphones/usages
Attaching the transmitter to clothing
The transmitter is attached to clothing (e.g. belt,
waistband) with the supplied belt clip.
The clip is detachable so that you can also attach the
transmitter with the antenna pointing downwards. To do
so, withdraw the clip from its fixing points and attach it the
other way round.
The supplied BPP 1 bodypack pouch helps to protect the
transmitter against moisture.
12
Using the bodypack transmitter
Switching the transmitter on/off
The transmitter can only be switched off when the standard
display is shown on the display panel. When in the
operating menu, briefly pressing the ON/OFF button will
cancel your entry (ESC function) and return you to the
standard display with the last stored settings.
Note:
Remove the batteries or the accupack when the
transmitter will not be used for extended periods of
time.
̈ Press the two unlocking buttons µ and open the
battery compartment cover ¾.
»
¸
¾
µ
̈ Press the ON/OFF button ¸ to switch the transmitter
on. The red LED » lights up.
̈ To switch the transmitter off, press the ON/OFF
button ¸ until “OFF” appears on the display. The red
LED » goes off.
̈ Close the battery compartment. The battery
compartment cover ¾ locks into place with an audible
click.
13
Muting the transmitter
The transmitter has a MUTE switch that noiselessly mutes
the transmitter’s audio signal without switching the
transmitter off.
̈ Set the MUTE switch ¹ to the position “MUTE”. The
“MUTE” display appears on the display panel. Provided
that the pilot tone function is activated on both the
transmitter and the receiver, the “MUTE” display also
appears on the receiver display panel.
Ƹ
̈ Set the MUTE switch Ƹ back to the original position to
retransmit the audio signal.
Activating/deactivating the lock mode
The transmitter has a lock mode that can be activated or
deactivated via the operating menu (see “Activating/
deactivating the lock mode” on page 23). The lock mode
prevents that the transmitter is accidentally programmed
or switched off during operation.
14
The operating menu
A special feature of the Sennheiser ew 500 G2 series is the
similar, intuitive operation of transmitters and receivers. As
a result, adjustments to the settings can be made quickly
and “without looking” – even in stressful situations, for
example on stage or during a live show or presentation.
The buttons
Buttons Mode
To...
ON/OFF Standard display switch the transmitter on
and off
Operating menu cancel the entry and return
to the standard display
Setting mode
cancel the entry and return
to the standard display
SET
Standard display get into the operating menu
Operating menu get into the setting mode of
the selected menu
Setting mode
store the settings and
return to the top menu level
̆/̄
Standard display without function
Operating menu change to the previous
menu (̆) or change to the
next menu (̄)
Setting mode
adjust the setting of the
selected menu:
option (̆/̄)
Overview of menus
Display
Function of the menu
BANK
Switching between channel banks
Switching between the channels in a
channel bank
CHAN
TUNE
Setting a transmission frequency for
the channel bank “U” (user bank)
SENSIT
DISPLY
NAME
Adjusting the sensitivity (AF)
Selecting the standard display
Entering a name
Loading the factory-preset default
settings
RESET
Activating/deactivating the pilot tone
transmission
PILOT
LOCK
EXIT
Activating/deactivating the lock mode
Exiting the operating menu and
returning to the standard display
15
Working with the operating menu
By way of example of the “TUNE” menu, this section
describes how to use the operating menu.
After switching the transmitter on, the standard display is
shown on the display panel.
Getting into the operating menu
̈ Press the SET button to get from the standard display
into the operating menu. The last selected menu flashes
on the display.
Selecting a menu
̈ Press the ̆/̄ rocker button to select a menu.
̈ Press the SET button to get into the setting mode of the
selected menu. The current setting that can be adjusted
flashes on the display.
Adjusting a setting
̈ Press the ̆/̄ rocker button to adjust the setting.
By briefly pressing the ̆/̄ rocker button, the display
jumps either forwards or backwards to the next setting.
In the “CHAN”, “TUNE” and “NAME” menu, the ̆/̄
rocker button features a “fast search” function. If you
hold down a button, the display cycles continuously,
allowing you to get fast and easily to your desired
setting.
16
Storing a setting
̈ Press the SET button to store the setting. “STORED”
appears on the display, indicating that the setting has
been stored. The display then returns to the top menu
level.
With most menus, new settings become effective
immediately without having to be stored. An exception
are the “BANK”, “CHAN”, “TUNE” and “RESET” menus.
With these menus, new settings only become effective
after they have been stored (“STORED” appears on the
display, indicating that the setting has been stored).
Exiting the operating menu
̈ Select the “EXIT” menu to exit the operating menu and
to return to the standard display.
When in the operating menu, briefly pressing the
ON/OFF button will cancel your entry (ESC function) and
return you to the standard display with the last stored
settings.
17
Operating menu of the transmitter
SET
EXIT
SET
BANK 1
BANK U
BANK
Changing the channel
bank
̆ /
̄
:
1...8, U (User
Bank)
Current channel bank
SET: Stores the setting
STORED
SET
B.CH
B.CH
1.02
CHAN
1.03
Current channel
(display depends on
"DISPLY" setting)
̆ /
̄
:
Channel 01...20
Changing the channel
SET: Stores the setting
STORED
SET
MHz
790.025
791.125
MHz
TUNE
Current frequency on
the selected channel
Setting the frequency
for channel bank "U"
̆ /
̄
:
Transmission
frequency in steps of
25 kHz
SET: Stores the setting
STORED
-10 dB
SET
-30 dB
SENSIT
Setting the sensitivity
Current sensitivity
setting
̆ / ̄: 0...-30 dB
SET: Stores the setting
STORED
SET
FREQ
NAME
DISPLY
Switching between the
standard displays
Current standard display
̆ /
̄
: FREQ, NAME,
CHAN
SET: Stores the setting
STORED
NAME
18
DISPLY
SET
NAME
VOCAL
GUCAL
Assigning the
Current transmitter name
̆ /
̄
:
Transmitter name
transmitter a name
(6 characters)
Letters w/o pronounciation
marks, numbers from 0...9,
special characters, spaces
STORED
SET: 5 x next character,
then store
SET
RST. NO
RST. OK
RESET
Security check
̆ /
̄:
OK, NO
Loading the factory-
preset default settings
"reset" = OK:
SET: Transmitter loads
factory-preset default
settings (only pilot tone
setting is kept), transmitter
is restarted, standard
display appears
"reset" = NO
SET: Reset is cancelled
SET
PLT. ON
PLT. OFF
PILOT
Pilot tone transmission
activated or deactivated
̆ /
̄:
ON, OFF
Activating/deactivating
the pilot tone
SET: Stores the setting
transmission
STORED
LOC.OFF
SET
LOC.ON
LOCK
Lock mode activated or
deactivated
̆ /
̄
:
ON, OFF
Activating the lock mode
Lock mode = ON:
SET: Stores the setting
("STORED"), returns to
standard display
Lock mode = OFF:
SET: Stores the setting
STORED
SET
EXIT
Exiting the operating
menu
BANK
19
Adjustment tips for the
operating menu
Switching between channel banks – BANK
Via the “BANK” menu, you can switch between the
transmitter’s nine channel banks. Each of the channel
banks “1” to “8” has up to 20 switchable channels that are
factory-preset to a transmission frequency (see “The
The channel bank “U” (user bank) has up to 20 switchable
channels to store your selection out of 1440 transmission
frequencies that are freely selectable within the preset
frequency range.
When switching from one channel bank to another, the
channel with the lowest channel number is automatically
displayed.
Switching between the channels – CHAN
Via the “CHAN” menu, you can switch between the different
channels in a channel bank. When switching between the
channels, please observe the following:
Always set the transmitter and the receiver of a
transmission link to the same channel.
Multi-channel operation
Combined with ew 500 G2 receivers, the transmitter can
form transmission links that can be used in multi-channel
systems. For multi-channel operation, only use the free
channels in a channel bank.
Before putting the transmission links into operation, we
recommend performing an auto scan (see operating
manual of the receiver).
Selecting the frequencies to be stored
in the channel bank “U” – TUNE
Via the “TUNE” menu, you can select the frequencies to be
stored in the channel bank “U” (user bank).
When you have selected one of the channel banks “1” to
“8” and then select the “TUNE” menu, the transmitter
automatically switches to channel 01 of the channel bank
“U”.
In this case, “U.01” briefly appears on the display.
20
̈ Use the ̆/̄ rocker button to select the desired
transmission frequency. Transmission frequencies are
tunable in 25-kHz steps within a switching bandwidth
of 36 MHz max. For intermodulation-free frequencies,
please refer to the enclosed frequency table.
Adjusting the sensitivity – SENSIT
Via the “SENSIT” menu, you can adjust the transmitter’s
input sensitivity.
The input sensitivity is adjusted too high when close talking
distances, speakers with loud voices or loud music passages
cause overmodulation in the transmission link. In this case,
the transmitter’s yellow LED (AF PEAK) ꢁ will light up.
¿
If, on the other hand, the sensitivity is adjusted too low, the
transmission link will be undermodulated, which would
result in a signal with high background noise.
The sensitivity is correctly adjusted when the level display
for audio signal “AF” ቩ shows full deflection only during
the loudest passages.
Note:
For monitoring the adjusted sensitivity, the
transmitter’s level display for audio signal “AF” always
indicates the audio level – even if the transmitter is
muted.
The following figures are a guide to the best settings:
y Loud music/vocals:
y Presentations:
–30 to –20 dB
–20 to –10 dB
–10 to 0 dB
y Interviews:
y Musical instruments:
y electric guitars with
single coil pickups:
–10 bis 0 dB
y electric guitars with
humbucker pickups:
–20 to –10 dB
y guitars with active
electronics (active pickups,
active EQs, piezo pickups):
–30 to –20 dB
21
Selecting the standard display – DISLPY
Via the “DISPLY” menu, you can select the standard display:
Contents of standard
Selectable standard display
display
“FREQ”
“NAME”
“CHAN”
Entering a name – NAME
Via the “NAME” menu, you can enter a freely selectable
name for the transmitter. You can, for example, enter the
name of the performer for whom the adjustments have
been made.
The name can be displayed on the standard display and can
consist of up to six characters such as:
y letters (without pronounciation marks),
y numbers from 0 to 9,
y special characters e.g. () - . _ and spaces.
To enter a name, proceed as follows:
̈ Press the SET button to get into the setting mode of the
“NAME” menu. The first segment starts flashing on the
display.
̈ With the ̆/̄ rocker button you can now select a
character. By briefly pressing a button, the display
jumps either forwards or backwards to the next
character. If you hold down a button, the display starts
cycling continuously.
̈ Press the SET button to change to the next segment and
select the next character.
̈ Have you entered the name completely? Press the SET
button to store your setting and to return to the top
menu level.
Loading the factory-preset default
settings – RESET
Via the “RESET” menu, you can load the factory-preset
default settings. Only the selected setting for the pilot tone
22
remains unchanged. After the reset, the transmitter is
restarted and the standard display is shown on the display
panel.
Activating/deactivating the pilot tone
transmission – PILOT
Via the “PILOT” menu, you can activate or deactivate the
pilot tone transmisssion.
The pilot tone supports the receiver’s squelch function
(Squelch) and protects against interference due to RF
signals from other units. The transmitter adds an inaudible
signal, known as the pilot tone, to the transmitted signal.
The receiver detects and evaluates the pilot tone.
Transmitters of the ew 500 series (first generation) do not
transmit a pilot tone and the receivers of the ew 500 series
(first generation) cannot evaluate the pilot tone.
Nevertheless, you can combine the transmitter with a
receiver of the first generation by observing the following:
y With the ew 500 G2 transmitter and an ew 500 G2
receiver:
Activate the pilot tone function with both transmitter
and receiver.
y With the ew 500 G2 transmitter and an ew 500 receiver
or vice versa:
Deactivate the pilot tone function with the ew 500 G2
transmitter or receiver.
Activating/deactivating the lock mode – LOCK
Via the “LOCK” menu, you can activate or deactivate the
lock mode.
The lock mode prevents that the transmitter is accidentally
programmed or switched off during operation. The lock
mode icon ቨ on the display indicates that the lock mode is
activated.
ቨ
To deactivate the lock mode, first press the SET button and
then press the ̆/̄ rocker button to select “LOC.OFF”. If
you confirm your selection by pressing the SET button, the
buttons can be operated as usual.
Exiting the operating menu – EXIT
Via the “EXIT” menu, you can exit the operating menu and
return to the standard display.
23
Troubleshooting
Error checklist
Problem
Possible cause
Possible solution
No
Batteries are flat or Replace the
operation
indication
accupack is flat
batteries or
recharge the
accupack
No RF signal Transmitter and
receiver are not on
Set transmitter and
receiver to the same
channel
the same channel
Transmitter is out of Check the squelch
range
threshold setting
or reduce the
distance between
transmitter and
receiving antenna
RF signal
available,
no audio
signal,
“MUTE”
display
appears on
the display
panel
Transmitter is muted Deactivate the
(“MUTE”)
muting function
Receiver’s squelch
Reduce the squelch
threshold is adjusted threshold
too high
Transmitter doesn’t Activate the pilot
transmit a
pilot tone
tone transmission
Audio signal Transmitter
See “Adjusting the
has a high
level of
sensitivity is
adjusted too low
background
noise
Receiver’s AF output Increase the audio
level is adjusted too output level
low
Audio signal Transmitter
is distorted sensitivity is
See “Adjusting the
adjusted too high
Receiver’s AF output Reduce the AF
level is adjusted too output level
high
If problems occur that are not listed in the above table or if
the problems cannot be solved with the proposed solutions,
please contact your local Sennheiser agent for assistance.
24
Recommendations and tips
... for the ME 2 and ME 4 clip-on microphones
y To reduce level variations to a minimum when the user
turns his or her head away from the microphone, attach
the microphone as centrally as possible.
y To protect the microphone against excessive sweat/
moisture, avoid direct skin contact.
y Attach the microphone carefully and conduct the cable so
that noise due to friction is avoided.
y Always use the ME 4 directional microphone with a
windshield and direct the microphone towards the sound
source (e.g. mouth).
... for the ME 3 headmic
y Always use the microphone with a popshield and position
the microphone at the corner of the mouth.
y You can vary the bass reproduction by increasing/
decreasing the talking distance.
y Make sure that the sound inlet is directed towards the
mouth. The sound inlet is marked with a little dot.
... for the bodypack transmitter
y Make sure that the antenna and the microphone cable do
not cross.
y The antenna should hang freely and be at least 1 cm away
from the body. The antenna must not be in direct contact
with the skin.
y For best results, make sure that the transmitter
sensitivity is correctly adjusted.
... for optimum reception
y Transmission range depends to a large extent on location
and can vary from about 10 m to about 150 m. There
should be a “free line of sight” between transmitting and
receiving antennas.
y To avoid overmodulating the receiver, observe
a
minimum distance of 5 m between transmitting and
receiving antennas.
... for multi-channel operation
y For multi-channel operation, you can only use the
channels in a channel bank. Each of the channel banks “1”
to “8” accommodates up to 20 factory-preset
frequencies which are intermodulation-free. For
alternative frequency combinations, please refer to the
enclosed frequency table. The freely selectable
frequencies can be selected via the “TUNE” menu and can
be stored in the channel bank “U”.
y When using several transmitters simultaneously,
interference can be avoided by maintaining a minimum
distance of 20 cm between two transmitters.
25
Specifications
RF characteristics
Modulation
wideband FM
Frequency ranges
518–554, 626–662,
740–776, 786–822,
830–866 MHz
Transmission frequencies
8 channel banks with up
to 20 factory-preset
channels each
1 channel bank with up to
20 freely selectable
channels (1440
frequencies, tunable in
steps of 25 kHz)
Switching bandwidth
Nominal/peak deviation
Frequency stability
36 MHz
24 kHz / 48 kHz
≤
15 ppm
RF output power at 50 Ω
typ. 30 mW
AF characteristics
Noise reduction system
AF frequency response
Sennheiser HDX
40–18,000 Hz
≥ 110 dB(A)
S/N ratio (at 1 mV and peak
deviation)
THD (at nominal deviation
and 1 kHz)
≤ 0.9 %
Max. input voltage
(at peak deviation)
Microphone 1.8 V
unbalanced
rms,
rmsf
Line 2.9 V
Input impedance
Microphone 10 kΩ, unbalanced
Line 1 MΩ
Overall unit
Temperature range
Power supply
– 10 °C to + 55 °C
2 AA size batteries, 1.5 V
or BA 2015 accupack
Nominal voltage
2.4 V
Max. power consumption at
nominal voltage
≤ 170 mA
Power consumption with
switched-off transmitter
≤ 250 μA
Operating time (with batteries)
≥ 8 h
Operating time (with BA 2015
accupack)
≥ 8 h
Dimensions [mm]
82 x 64 x 24
Weight (incl. batteries)
approx. 158 g
27
Microphones
ME 2
MKE 2-ew ME 3
ME 4
Transducer
Principle
condenser condenser condenser condenser
Sensitivity 20 mV/Pa 5.6 mV/Pa 1.6 mV/Pa 40 mV/Pa
Pick-up
pattern
omni-
omni-
super-
cardioid
directional directional cardioid
130 dB SPL 140 dB SPL 150 dB SPL 120 dB SPL
Max. SPL
Connector assignment
3.5 mm jack plug:
Polar diagrams and frequency response
curves of microphones
Polar diagram
ME 3
Polar diagram
ME 4
28
Frequency response curve ME 2
Frequency response curve ME 3
Frequency response curve ME 4
Accessories
ME 2:
MKE 2:
ME 4:
Clip-on microphone,
condenser, omni-directional
Clip-on microphone , black or beige,
condenser, omni-directional
Clip-on microphone,
condenser, cardioid
ME 3:
CI 1:
Headmic, condenser, super-cardioid
Instrument cable,
with ¼” (6.3 mm) jack plug
CL 2:
DC 2:
Line input cable,
with XLR-3F connector
DC power adapter,
for external 12 V DC powering
(instead of two AA size batteries)
BA 2015:
L 2015:
CC 2:
Accupack
Charger for BA 2015 accupack
Carrying case
29
Manufacturer declarations
Warranty regulations
The guarantee period for this Sennheiser product is 24 months from the date
of purchase. Excluded are accessory items, rechargeable or disposable batte-
ries that are delivered with the product; due to their characteristics these pro-
ducts have a shorter service life that is principally dependent on the individual
frequency of use.
The guarantee period starts from the date of original purchase. For this reason,
we recommend that the sales receipt be retained as proof of purchase. Wit-
hout this proof (which is checked by the responsible Sennheiser service part-
ner) you will not be reimbursed for any repairs that are carried out.
Depending on our choice, guarantee service comprises, free of charge, the
removal of material and manufacturing defects through repair or replacement
of either individual parts or the entire device. Inappropriate usage (e.g. opera-
ting faults, mechanical damages, incorrect operating voltage), wear and tear,
force majeure and defects which were known at the time of purchase are exclu-
ded from guarantee claims. The guarantee is void if the product is manipulated
by non-authorised persons or repair stations.
In the case of a claim under the terms of this guarantee, send the device, inclu-
ding acces-sories and sales receipt, to the responsible service partner. To mini-
mise the risk of transport damage, we recommend that the original packaging
is used. Your legal rights against the seller, resulting from the contract of sale,
are not affected by this guarantee.
The guarantee can be claimed in all countries outside the U.S. provided that no
national law limits our terms of guarantee.
CE Declaration
of Conformity
This equipment is in compliance with the essential requirements and other
relevant provisions of Directives 1999/5/EC, 89/336/EC or 73/23/EC. The
Before putting the device into operation, please observe the respective coun-
try-specific regulations!
Batteries or rechargeable batteries
The supplied batteries or rechargeable batteries can be recycled.
Please dispose of them as special waste or return them to your spe-
cialist dealer. In order to protect the environment, only dispose of
exhausted batteries.
WEEE Declaration
Your Sennheiser product was developed and manufactured with
highquality materials and components which can be recycled and/
or reused. This symbol indicates that electrical and electronic equip-
ment must be disposed of separately from normal waste at the end
of its operational lifetime.
Please dispose of this product by bringing it to your local collection point or
recycling centre for such equipment. This will help to protect the environment
in which we all live.
30
Sennheiser electronic GmbH & Co. KG
30900 Wedemark, Germany
Phone +49 (5130) 600 0
Fax +49 (5130) 600 300
Printed in Germany
Publ. 02/06
090663/A2
|