Sears Power Supply 20071521 User Guide

OPERATOR’S MANUAL  
®
Universal Power and Adapter Kit  
2 Amp DC to DC Converter  
Model No.  
200.71521  
CAUTION:  
Read all Safety Rules and Operating Instructions,  
and follow them with each use of this product.  
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.  
00-99-000868/0808  
 
IMPORTANT: READ AND SAvE THIS SAfETY AND INSTRUCTION MANUAL.  
1.  
IMPORTANT SAfETY INSTRUCTIONS  
Before using your Universal Power and Adapter Kit converter, read and  
understand this Owner’s Manual.  
1.1  
Keep the Universal Power and Adapter Kit well ventilated in order to prop-  
erly disperse heat generated while it is in use. Make sure that there are  
several inches of clearance around the top and sides and do not block the  
slots of the converter.  
1.2  
Make sure the Universal Power and Adapter Kit is not close to any poten-  
tial source of flammable fumes, gases or clothing.  
1.3  
1.4  
Keep the Universal Power and Adapter Kit dry.  
DO NOT allow the Universal Power and Adapter Kit to come into contact with  
rain or moisture.  
1.5  
DO NOT operate the Universal Power and Adapter Kit if you, the con-  
verter, the device being operated or any other surfaces that may come in  
contact with any power source are wet. Water and many other liquids can  
conduct electricity, which may lead to serious injury.  
1.6  
1.7  
1.8  
1.9  
Do not place the Universal Power and Adapter Kit on or near heating  
vents, radiators or other sources of heat.  
Do not place the Universal Power and Adapter Kit in direct sunlight. The  
ideal air temperature for operation is between 50° and 80°F.  
Do not use the Universal Power and Adapter Kit near an open engine  
compartment.  
Only connect the Universal Power and Adapter Kit to a 12 - 16.5 volt ac-  
cessory outlet.  
1.10 Do not modify the adapter plugs or connectors in any way.  
1.11 Use only five amp fuses.  
wARNINg: Pursuant to California Proposition 65, this product contains  
chemicals known to the State of California to cause cancer and birth de-  
fects or other reproductive harm.  
NOTE: Nintendo®, PSP®, Game Boy®, IPod®, and Nintendo DS® are  
registered trademarks of independently owned and operated companies.  
This product has not been licensed or endorsed by these companies or  
their manufacturer.  
1 •  
 
2.  
PRODUCT fEATURES  
7
8
1
5
9
3
6
1. Nintendo game boy® Adapter  
Plug*  
2. Mini-USb Adapter Plug  
3. Nintendo DS® Adapter Plug*  
4. USb Adapter Plug  
(Adapter Plugs 1-4 come  
assembled in bag)  
2
1
4
3
5. Six Piece Adapter Plug Set  
6. Carrying Case  
7. Connector Plug  
8. Selector Knob  
9. Converter  
*Adapter plugs 1&3 are compat-  
ible with but not manufactured by  
Nintendo®  
3.  
bEfORE USINg THE UNIvERSAL POwER AND ADAPTER KIT  
3.1  
It is important to know that this converter only supplies DC power at the  
voltage you set it to. Read the specifications in the “input” section of the  
device’s manual you are about to power before plugging it in.  
3.2  
This converter only charges  
devices (positive center pin, and  
negative outside). If the polarity of the device you are trying to power has  
a negative center pin and positive outside  
not work.  
the converter will  
O.K.  
3.3  
Make sure that the device is turned OFF before inserting plugs. Failure to  
do so may cause damage that isn’t covered by the manufacturer’s normal  
warranty.  
2 •  
 
4.  
OPERATINg INSTRUCTIONS  
The Universal Power and Adapter Kit comes in a carrying case with 10  
adapter plugs. Select the appropriate connector for the device you would  
like to operate.  
4.1  
4.2  
Setting the Converter voltage  
Determine the proper voltage setting by checking the electronic device  
rating plate, owner’s manual, or number of batteries.  
Plugging Adapter Plugs into the Universal Power and Adapter Kit  
and Electronic Device:  
After selecting the appropriate adapter plug, push into the Universal Pow-  
er and Adapter Kit’s cord plug. NOTE: Each connector has a tab guide so  
that they will only fit into the plug one way. Forcing the connector into the  
plug the wrong way (reversed polarity) will cause damage to your device  
and/or Universal Power and Adapter Kit.  
Make sure the electronic device is turned off. Firmly push the selected  
adapter into the device input socket.  
4.3  
Plugging Universal Power and Adapter Kit in vehicle:  
Make sure that the 12V accessory (cigarette) outlet in your vehicle is free  
of any materials and debris. Particles in the accessory outlet could cause  
a short; blowing the fuse in your vehicle and/or Universal Power and  
Adapter Kit.  
Make sure that the vehicle’s engine is off and there is not anything  
plugged into the Universal Power and Adapter Kit other than the selected  
connector.  
Firmly plug the 12V end of the Universal Power and Adapter Kit into the  
12V accessory outlet.  
NOTE: Some vehicles’ 12V outlets are not live unless the key is turned  
to the ACC position. If the red LED does not illuminate on the Universal  
Power and Adapter Kit, turn the vehicle’s key to the ACC position without  
starting the engine.  
The Red LED illuminates when the Universal Power and Adapter Kit  
converter receives power from the 12V accessory outlet. The Universal  
Power and Adapter Kit is equipped with a five amp fuse, located in the  
neck of the converter, for overload protection. See the Troubleshooting  
section for instructions on how to replace the fuse.  
Turn on the electronic device.  
It is not recommended to leave the Universal Power and Adapter Kit  
plugged into the vehicle’s 12V accessory outlet while the car is not run-  
ning. Doing so may drain the vehicle’s battery.  
WARNING: To ensure that damage will not occur, check voltage and  
polarity of electronic device before using this product. ALWAYS SWITCH  
OFF APPLIANCES PRIOR TO INSERTION OF PLUGS. Failure to do so  
may cause damage that is not covered by the normal warranty. It is best to  
3 •  
 
check your owner’s manual.  
4.4  
Storage of Adapter Plugs and Converter:  
The carrying case is equipped with 10 pocket holders for the adapter  
plugs and a strap for the converter.  
• The first four pockets across the top are specifically labeled for each con-  
nector.  
The rest of the pockets have suggested labels, but the adapter plugs can  
be stored in any of the six pockets that you feel fit for your devices.  
5.  
POwER SOURCE AND OUTPUTS  
The Universal Power and Adapter Kit operates with any 12 - 16.5V DC  
power source. The converter’s power is dependant on and is determined  
by the charge and life of the vehicle’s battery.  
The Universal Power and Adapter Kit supplies DC voltage in the range of  
3V, 4.5V, 5V (USB), 6V, 9V and 12V DC at a maximum of 2 amps. Setting  
the wrong voltage may damage the device you are trying to power.  
Read the device’s owner’s manual specifications under the “input”  
section to determine proper voltage. Using devices rated over 2  
Amps will blow the fuse and could cause damage to the Universal  
Power and Adapter Kit.  
6.  
USAgE ExAMPLES  
Device Type  
Portable CD Player  
Estimated voltage  
3 Volts  
Camcorder  
4.5 Volts  
IPod®  
5 Volts (USB)  
5.4 Volts  
PSP®, Game Boy®, Nintendo DS®  
Camera  
GPS  
6 Volts  
9 Volts  
Radio  
12 Volts  
Some devices may have different specifications than the ones listed in the  
table. Please refer to device’s owner’s manual before using the converter.  
7.  
SPECIfICATIONS  
Input Voltage  
Output Voltage  
Fuse  
12 - 16.5V DC  
3V, 4.5V, 5V, 5.4V, 6V, 9V, 12V DC  
5A /250V  
Adapter Plugs  
Mini USB, USB, Game Boy®, Nintendo DS®, 2.3mm yellow,  
3.3mm orange, 4.0mm yellow, 5mm red, 5.5mm blue, 5.5mm  
white.  
Dimensions  
7 x 1.42 x 2.75”  
4 •  
 
8.  
REPLACEMENT PARTS  
5A fuse: 0099000549  
USb Adapter Plug: 0699000281  
Mini-USb Adapter Plug: 0699000284  
Nintendo game boy® Adapter Plug: 0699000282*  
Nintendo DS® Adapter Plug: 0699000283*  
Six Piece Adapter Plug Set: 2299001762  
*Nintendo Game Boy® and Nintendo DS® adapter plugs are compatible  
with but not manufactured by Nintendo®.  
9.  
TROUbLESHOOTINg  
Problem  
Cause  
Solution  
Device you’re trying to  
power doesn’t work.  
Converter is set to  
wrong voltage.  
Check device specifications.  
Device polarity doesn’t  
match.  
This unit only works with  
The LED is not illuminating  
and device doesn’t work in  
either converter or vehicle.  
Bad Fuse.  
Change Fuse (Directions  
below)  
Not inserted all the way. Make sure the converter is  
firmly pushed into the acces-  
sory outlet.  
12V accessory plug  
may be malfunctioning.  
Plug in a different device. If no  
results, then check outlet for  
debris and then check fuse.  
Damaged Cords  
Please take to a qualified  
service technician. Never use if  
cord is damaged.  
Call 1-800-SEARS-64 for  
troubleshooting assistance.  
Inverter may be defective.  
9.1  
Changing the fuse in the Universal Power and Adapter Kit:  
Make sure there are not any loads connected to the Universal Power and  
Adapter Kit.  
Unscrew the head. Be careful not to lose the tab and spring.  
Turn the Universal Power and Adapter Kit upside down and let the fuse  
fall in your hand.  
• Replace new fuse and reverse directions. Twist the head on finger tight.  
Be sure not to overtighten because it may cause damage to the con-  
verter.  
5 •  
 
6 •  
 

Radio Shack Cordless Telephone 43 3821 User Guide
RBH Sound Lawn Mower RBH 180 User Guide
RCA Telephone 25255 User Guide
Renesas Computer Hardware M30280T 85LGF User Guide
Ryobi Trimmer RY41140 User Guide
Samsung Home Theater System HT E6750W User Guide
Samsung Network Card SADT 100HM User Guide
Sanyo Battery Charger N 50AAAS User Guide
Sanyo VCR TLS 9924P User Guide
Senario Handheld Game System 20986 User Guide