HD RadioTM Component Tuner
User Manual
381R20S-A
20070425_HDT-1&HDT-1X_381R20S-A_«Ê-1±.p65
2007/4/27, ¤U¤È 03:58
HD Radio™ Technology Manufactured Under License From iBiquity Digital Corporation.
iBiquity Digital and the HD Radio and HD logos are registered trademarks of iBiquity Digital
Corporation. HD RadioTM is a trademark of iBiquity Digital Corporation. U.S. and Foreign Patents.
20070425_HDT-1&HDT-1X_381R20S-A.p654
2007/4/30, ¤U¤È 01:43
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
11. Use only with the cart, stand, tripod, bracket or table specified by
the manufacturer or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally ,
or has been dropped .
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
14. To reduce the Risk of Fire or Electric Shock. Do not expose this
appliance to rain or moisture.
15. The Shock Hazard marking and Associated Graphical Symbol is
provided on the rear panel of unit.
9. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
16. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, shall not be placed on the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
2
20070425_HDT-1&HDT-1X_381R20S-A.p655
2007/4/30, ¤U¤È 01:43
Main Unit Controls
(Front & Remote Control)
Unit Button
Remote Button
Action/Combination
Function
1
2
A
C
Turns unit on/off
10 Digit Keypad
FREQ
Programs Memory Presets
Allows Direct Entry of Channel Frequency
Allows recall of memory presets
Allows Direct Time Entry for Clock
Preset
Clock Set
3
4
5
N/A
N/A
G
Remote Sensor
LCDDisplay
Tuning
Step Tunes Up/Down
Advanced Menu Options
Seek Tuning
HD Seek Tuning
BAND
Activates/Deactivates Settings
6
7
8
9
H
I
Seeks to next detectable frequency
Seeks to next detectable HD Radio Broadcast Signal
Selects AM/FM Bands
D
B
INFO
Toggles through Display Modes
2 sec. hold
FREQ
Provides Access to Advanced Menu Options
Prepares Tuner for Direct Frequency Entry Using #2, Remote Keys “C”
Prepares Tuner to Recall Memory Presets Using #2, Remote Keys “C”
Indicates if Unit is On or Off
10
11
12
E
F
PRESET
N/A
Standby LED Indicator
3
20070425_HDT-1&HDT-1X_381R20S-A.p656
2007/4/30, ¤U¤È 01:43
4
20070425_HDT-1&HDT-1X_381R20S-A.p657
2007/4/30, ¤U¤È 01:43
Main Unit Controls
(Rear)
13.
14.
External FM antenna socket
External AM loop antenna socket
17. SPDIF Optical Connection (Optional on HDT-1X)
18. AC power cord socket
15. 16. Line Out socket
5
20070425_HDT-1&HDT-1X_381R20S-A.p658
2007/4/30, ¤U¤È 01:43
Accessories
Detachable power Cord x 1
FM Dipole Antenna x 1
AM Loop antenna x 1
6
20070425_HDT-1&HDT-1X_381R20S-A.p659
2007/4/30, ¤U¤È 01:44
RCA type audio cable x 1
Remote control unit x 1
Instruction manual x 1
Warranty cardSeek Function
To seek to another clear station, use the SEEK toggle button . Press
7
20070425_HDT-1&HDT-1X_381R20S-A.p6510
2007/4/30, ¤U¤È 01:44
Getting started
Step 1.
NOTE WHICH INPUT YOUARE USINGWHENCONNECTINGTHE
HDT-1/HDT-1X TUNER TO YOURAV SYSTEM FOR LATER
REFERENCE.
Inspect package to insure that all parts & accessories are included.
Step 2.
a. Using RCA Cables
Find a proper location for your new HDT-1/HDT-1X HD Radio Tuner
following the guidelines on table 1.1.
i. Connect included or premium RCA cables to your AV system.
ii. Connect opposite end of the included or premium RCA cables to
your new HDT-1/HDT-1X HD Radio Tuner to Figure 2, #15 & #16.
Step 3.
Connect the included or other external FM antenna to Figure 2, #13.
b. Using Optional SPDIF connection (On HDT-1X only). Always prevent
excessive bending of the optical cable as this may distort audio
and/ or cause damage to your AV system or HDT-1/HDT-1X HD
Radio Tuner.
Step 4.
Connect the included or other external AM antenna to Figure 2, #14.
i. Connect optical cable to your AV system according to the cables
manufacturers directions.
NOTE:
TO IMPROVE RECEPTIONANDDECREACE INTERFEARANCE FROM
YOURNEW HDT-1/HDT-1X PLACE THEAM LOOPANTENNAAT
LEAST 50MM AWAY FROM UNIT.
ii. Connect opposite end of the optical cable to your new
HDT-1/HDT-1X using connectors in Figure 2, #17
Step 6.
Step 5.
Connect the AC power cable to the HDT-1/HDT-1X using connector in
Figure 2, #18. Connect the opposite end into an AC outlet located near
the unit.
Connect your new HDT-1/HDT-1X to your AV system using either the
RCA Connection or Optional SPDIF Connection (On HDT-1X Model
Only). Always connect to your AV system first, then to your new
HDT-1/HDT-1XTuner.
8
20070425_HDT-1&HDT-1X_381R20S-A.p6511
2007/4/30, ¤U¤È 01:44
Navigating the Display
There are many display functions. This will help you understand what
the display is telling you, making navigation and setup easier.
(A)Radiotext, (B)Time, (C)Signal quality, (D)Frequency,
(E)and Audio spectrum.
: HD RADIO Indicator
: Siqnal Indicator
: Station Name-MulticastSetIndex
: Artist
: Title
: Program Type
: Sterei Indicator(For HDT-1X only)
: RDS Indicator
: Program Station
: Program Type
: Callsign
: Radio Text
9
20070425_HDT-1&HDT-1X_381R20S-A.p6512
2007/4/30, ¤U¤È 01:44
Setting up and Programming your HDT-1/HDT-1X
Setting the clock
Clock setting can be done when the tuner is in Standby (power off)
1. Press and hold “INFO” button for approx. 2 seconds until display
flashes “clock set “to enter Clock Set mode.
2. Press Tuning UP or Down button to select AM or PM.
3. Press number keys to set required clock time.
4. Press INFO button again to complete clock time set.
e.g. to set 9.45 AM
a. Press INFO to enter clock set mode.
b. Press Tuning UP to get AM.
c. Press 0,9,4,5.
d. Press INFO again to complete clock time set.
Display will appear ERROR if the input is incorrect.
10
20070425_HDT-1&HDT-1X_381R20S-A.p6513
2007/4/30, ¤U¤È 01:44
Radio Controls
To turn the radio on, press the Standby button. Pressing the Standby
button again will put the unit into standby. In standby, the tuner will
display the time, dim the backlight and standby LED will be on.
Selecting the radio band
Press the BAND button to select the appropriate band . At each press of
the BAND button, the band switches from AM1 AM2 FM1 FM2.
When you switch from one band to another, the radio will return to the
last tuned station used in the band.
11
20070425_HDT-1&HDT-1X_381R20S-A.p6514
2007/4/30, ¤U¤È 01:44
Manual Tuning
Press the TUNING rocker switch UP or DOWN to tune up or down to
select a radio station. Tuning step per press for AM band is 10 kHz
and 100 kHz for FM band.
Direct Tuning
By using numbered key pad, you can directly tune to a radio station.
For example, to tune to station 93.30 FM, press BAND button to
select FM band followed by pressing FREQ button and numbered
buttons 9-3-3. To tune to 1120 AM, press BAND button to select
AM band, followed by pressing FREQ button and buttons 1-1-2-0.
Display will appear ERROR if the input frequency is incorrect or out
of coverage.
12
20070425_HDT-1&HDT-1X_381R20S-A.p6515
2007/4/30, ¤U¤È 01:44
Receiving HD radio stations
When the radio is tuned to a station broadcasting HD radio signal,
the LCD will display a blinking “HD “logo. Once the tuner acquires the
HD radio signal, the “HD” logo will stay on and a Signal Strength
indication will appear in the top right hand corner.
Receiving Multicast Stations
When the radio is tuned to an HD radio compatible station and it
determines that one or more Multicast stations are available,
the Frequency or the Call Letters will be followed by a “-1” designator,
indicating that there is at least one Multicast station available.
The TUNE UP button will tune up from a station’s Main Program Service
Station to the Multicasting programs.
13
20070425_HDT-1&HDT-1X_381R20S-A.p6516
2007/4/30, ¤U¤È 01:44
Seek Function
HD SEEK function
To seek to another clear station, use the SEEK toggle button.
Press and release the SEEK UP or DOWN will go to the next available
station with good signal. Press any key to stop SEEK function.
Using the HD SEEK button, the tuner will seek to the next available HD
station. This function will also scan to the Multicast program if available.
Press and release HD SEEK UP or DOWN will go to the next available
HD station with good signal. Press any key to stop HD SEEK function.
Using AM and FM presets
Presetstations
There are 20 preset stations for FM (10 x FM1, 10 x FM2) and 20 preset
stations for AM (10 x AM1, 10 x AM2). First select the AM/FM using the
band selection button ( AM1, AM2, FM1, FM2 ) , then press and hold for
3 seconds for the number 0-9 of where you would like to store this
station until display indicating the station is stored.
For HDT-1 only:
Note:
If presets are full, the display will appear FULL. Press and hold the
number key for more than 5 seconds, the current station will replace
the previous memorized station. And the display will show
PRESET – X stored.
14
20070425_HDT-1&HDT-1X_381R20S-A.p6517
2007/4/30, ¤U¤È 01:44
Recall preset stations
To recall preset stations, select required band by pressing BAND
selection button. Press PRESET button to enter PRESET recall mode.
Display will show “GO TO PRESET”. Then followed by using one of the
following methods to recall the stations.
1. Press and release the number station you like to recall.
2. Press TUNING UP or DOWN button to select required preset station.
Note:
If the preset station you like to recall has no preset station, display will
show EMPTY.
Exchange preset stations position
You may use the Presets exchange function to change the position of
the preset stations.
E.g. preset 1: 93.10 MHz and preset 2: 100.70 MHz
If you like to exchange preset 1 to be preset 2. First to recall Preset 1
station, then long press number button 2 for more than 2 seconds until
display indicating the new preset has been stored.
For HDT-1 only:
Note: If memory is full during preset station exchange, display will
appear FULL, then press number button 2 for more than 5 seconds until
display indicating the new preset has been stored.
15
20070425_HDT-1&HDT-1X_381R20S-A.p6518
2007/4/30, ¤U¤È 01:44
Advanced Information
Long press INFO button for 2 seconds to enter Advanced Information.
Press and release INFO button will cycle through information of RESET,
LCD Contrast Adjust, Backlight Brightness Control, (For HDT-1X:
Stereo/Mono Mode, Analog Mode, Split Audio Mode), Bit Error Rate,
The carrier to noise ratio, FUSE Bit Check , Transmission Mode,
Station ID and Software version.
a. RESET –
in RESET mode, press PRESET button to RESET the tuner.
The tuner setting will be reset to its initialized factory setting.
b. LCD Contrast –
pressing TUNING UP or DOWN button to adjust LCD contrast.
c. Back Light Setting –
pressing TUNING UP or DOWN button to adjust Back Light.
(for HDT-1X only)
d. Stereo/Mono Mode –
pressing TUNING UP or DOWN button to adjust Stereo/mono.
(only for HDT-1X )
e. Analog Mode –
pressing TUNING UP or DOWN button to turn on/off HD.
(for HDT-1X only)
f. Split Audio Mode –
pressing TUNING UP or DOWN button to split audio on/off.
(for HDT-1X only)
g. Bit Error Rate
h. The carrier to noise ratio
i. Fuse Bit Check
j. Transmission Mode ,
k. Station IDand HDT-1/HDT-1X
l. Software version are for factory and after sales service reference.
16
20070425_HDT-1&HDT-1X_381R20S-A.p6519
2007/4/30, ¤U¤È 01:44
Advanced Menu Options
Menu Option
Backlight
Function
Controls
Controls Backlight Brightness
Mono/Stereo switch
Mono/Stereo Mode
Tuning Up to activate option
Tuning Down to deactivate
Tuning Up to activate option
Tuning Down to deactivate
Tuning Up to activate option
Tuning Down to deactivate
Analog Mode (HD OFF)
Split Audio Mode
Bit Error Rate
Eliminated HD Radio Signal Tuning
Provides Digital Signal in Left Audio Channel
Provides Analog Signal in Right Audio Channel
The number of bits incorrectly received to the total number of bits sent during a
specified time interva
Carrier to Noise Ratio
Fuse Bit Check
Transmission Mode
Station ID
A measure of the received carrier strength relative to the strength of the received noise
Used for Diagnostic Purposes Only
This indicates the digital mode being used to transmit the audio
Used for Diagnostic Purposes Only
Software Version
Used for Diagnostic Purposes Only
17
20070425_HDT-1&HDT-1X_381R20S-A.p6520
2007/4/30, ¤U¤È 01:44
Troubleshooting
Issue
Possible Solutions
Possible Causes
Power Won’t Turn On
Check AC power cord connection
AC Power Cable is not properly connected
AC Outlet power not turned on
Defective/Malfunctioning Unit
Remote Battery Not Activated
Battery is Dead
Check circuit breakers/fuses
Call Sangean Service Department at 888-SANGEAN
Remove plastic piece located at bottom of remote
Replace battery
Remote Doesn’t Work
Check the area of the IR sensor and ensure there are no
obstructions and the area surrounding it is clean by using a
glass or all purpose cleaner
IR Sensor Obstructed
Call Sangean Service Department at 888-SANGEAN
Call Sangean Service Department at 888-SANGEAN
Check “Power won’t turn on”
IR Sensor Malfunctioning
Remote isDefective
I don’t hear any audio
Power is not on
I only hear audio in one speaker
Check to make sure audio cables are properly connected.
Make sure Left is Left, and Right is Right.If using optical,
make sure cable is not bent or kinked.
Audio cables are not properly connected
Check to make sure power is connected and retry
Make sure to set your AV Receiver to corresponding inputs
used during installation
AV Receiver is not powered on
AV Receiver is not set to proper input
Check speakers to make sure that they are all properly
connected
Speakers improperly connected
I only hear static
Poor audio quality
Check all antennas to ensure proper connection
Check to see that you are on a frequency that is broadcasting
in your area
Antenna not connected properly
Tuner not tuned to a station
Call station engineer, or try another station
Check to make sure you are using the proper cables for the
inputs you chose.
Station is temporarily not broadcasting
Bad/Improper Connections
Check to verify that all connections are to same format (RCA is
to RCA, Coaxial is to Coaxial, Antenna to Antenna input, etc.)
18
20070425_HDT-1&HDT-1X_381R20S-A.p6521
2007/4/30, ¤U¤È 01:44
Using the signal strength indicator or the Carrier to Noise
indicater, try different positions and orientations of the antenna
Contact radio broadcaster to inquire about poor audio quality
See above
Poor audio quality
(Cont.)
Antenna not correctly installed or oriented
Radio station is broadcasting poor signal
HD Signal Keeps Fading in and Out Antenna not correctly installer or oriented
Poor environmental conditions
There are certain environmental factors that will effect
radio reception. You should always try your tuner in a
different location, alter the orientation of the antenna,
and check all connections.
If all else fails, in the advanced menu on the HDT-1X, adjust turn
“Force Analog” setting to “ON”
If the HDT-1/HDT-1X is making a stange but detectable when the
unit is on and off disconnect power immediately and contact
Sangean ServiceDepartment at 888-SANGEAN
Stange sound when radio is off
Malfunctioning component
19
20070425_HDT-1&HDT-1X_381R20S-A.p6522
2007/4/30, ¤U¤È 01:44
Specifications
Power:
Antenna System:
Mains: AC 120 Volts 60 Hz only, 10 Watt maximum
Battery ( remote control ): 3.0V CR 2025
FM - Dipole type ( supplied )
AM - Loop type ( supplied )
Frequency coverage:
FM 87.50 - 108.10 MHz
AM 520 - 1710 kHz
Dimension ( W x H x D ): 430x70x256 mm
Weight: 2.6 kg.
HD FM 87.50 - 108.10 MHz
HD AM 520 - 1710 kHz
20
20070425_HDT-1&HDT-1X_381R20S-A.p6523
2007/4/30, ¤U¤È 01:44
HDT-1/HDT-1X Brief User Interface:
UI KEY function
NO Button
Action
short
Function Status
StandBy /
PowerOn
Function
Note
1
standby
PowerOn / StandBy toggle
recall the last station
on last band
2
Band
short
short
PWR ON
FM1 FM2 AM1 AM2
PWR ON
RT CT SSI Freq Spectrum
System Reset Contrast
Bit Error Rate Carrier To Noise Ratio
Fuse Bit Check Transmission Mode
Station ID SW version & DSP version
& SDK version
for HDT-1 only
for HDT-1X only
3
Info
long 2s
PWR ON
(To use info key to jump next status)
System Reset Contrast
Back Light Setting Stereo/Mono Mode
Analog Mode Split Audio Mode
Bit Error Rate Carrier To Noise Ratio
Fuse Bit Check Transmission Mode
Station ID SW version & DSP version
& SDK version
short(To use number key and tune
select clock time, then to press Info
button finish setting)
PWR OFF
PWR ON
PWR ON
To modify clock time
Reset system
long 2s(To use info key to jump next
status,when the status is RESET,
to press Preset button reset)
long 2s(To use info key to jump
next status, when the status is
LCD Contrast Adjust, to press tune
adjust contrast)
4
5
Info
Info
LCD Contrast Adjust
21
20070425_HDT-1&HDT-1X_381R20S-A.p6524
2007/4/30, ¤U¤È 01:44
1.To press preset button then to
press number button finish setting
2.To press number button long 2s
store channel
Recall Preset 0~9
Recall Preset 0~9
Store to Preset 0~9
Store to Preset 0~9
Store to Preset 0~9
FM1 BFM2
AM1 BAM2
FM1 BFM2
AM1 BAM2
for HDT-1 only
6
7
Preset
Tune
PWR ON
3.When preset memory is full. To press
number button long 5s store channel
short
PWR ON
PWR ON
PWR ON
PWR ON
PWR ON
PWR ON
PWR ON
"Tune up/down" for services up/down
Turn up or down to next Freq
"Tune up/down" for services up/down
Fast tuning up or down, 8 steps per sec
Auto scan to next strongest station
Auto scan to next HD station
Frequency tune
short
Push and Hold
Push and Hold
8
9
Seek
short
HD Seek
short
10 Freq
To press Freqt button then to press
number button select frequency
22
20070425_HDT-1&HDT-1X_381R20S-A.p6525
2007/4/30, ¤U¤È 01:44
|