WASHING MACHINE
User’s Manual
SW68ASP / SW57APP
Please read this manual before using and note how to use in the proper manner.
Please be careful of keeping the manual.
Otherwise, it should be bought separately.
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DESCRIPTION OF PARTS . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION & MAINTENANCE . . . . . . . . . . . . . . . . . 4
ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IN CASE OF PUMP-DRAINED WASHER . . . . . . . . . . . . . . . . . . 4
HOW TO CONNECT WATER SUPPLY HOSE . . . . . . . . . . . . . . . . 4
HOW TO CLEAN THE FILTER . . . . . . . . . . . . . . . . . . . . . . . . . 5
CLEANING THE FILTER (pump drained washer) . . . . . . . . . . . . . . . 5
HOW TO ADD THE DETERGENT . . . . . . . . . . . . . . . . . . . . . . . 5
LEVELLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
HOW TO ADD THE FABRIC SOFTENER . . . . . . . . . . . . . . . . . . 5
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CONTROL PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WASHING INSTRUCTION. . . . . . . . . . . . . . . . . . . . . . . 8
PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WASH PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WASHING PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 9
OPTIONAL CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 10
SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Register your product at
CODE NO. : DC68-02290A
SW68ASP-02290A-EN.indd
1
2006-08-21 ¿ÀÈÄ 8:33:06
DESCRIPTIONOFPARTS
LID
WATER SUPPLY HOSE
RED-HOT WATER
DRAIN HOSE
WATER SUPPLY HOSE
BLUE-COLD WATER
DETERGENT BOX
CONTROL PANEL
FABRIC SOFTENER
DISPENSER
BLEACH INLET
POWER PLUG
MAGIC FILTER
PULSATOR
HEIGHT
ADJUSTING FEET
2
SW68ASP-02290A-EN.indd
2
2006-08-21 ¿ÀÈÄ 8:33:08
SAFETYINSTRUCTIONS
Please note that the following precautions for safety intend to prevent unpredictable danger and damage
by helping the proper use in safety.
When using hot water in washing, please make sure that the water should not exceed 50˚C.
• Plastic parts may be deformed or damaged, and an electric shock or a fire may take place.
WARNING
CAUTIONS
There might be a slight injury or damage when you
violate this instruction.
There might be serious injury or fatal accident when
you violate this instruction.
• If the plug (power supply cord) is damaged, it
must be replaced by the manufacturer or its
service agent or a similarly qualified person in
order to avoid a hazard.
• Don’t install it in the area with moisture or outdoor
where it has rain or snow
- An electric shock or a fire may take place.
• Please unplug the power supply cord when you
do not use it.
- An electric shock or a fire may take place.
• Do not pull the cord off or touch it with moist
hands.
- An electric shock or a fire may take place.
• Do not bend the power supply cord by force or
press it with heavy things.
• If there is dust or water on the power supply plug
and its connected part, please remove it completely.
- An electric shock or a fire may take place.
- An electric shock or a fire may take place.
• Do not install the washer nearby electric
implement or don’t put a candle light or
cigarette light on the washer.
• Do not make your kids look into the inside of the
washer.
- If your kid falls into the washer, his life could be
in danger.
- A fire may take place.
• During operation, do not put your hands or metal
materials under the washer.
- You may be hurt by spinning board beneath the
washer.
• Ventilate immediately without touching the power
plug if gas is leaking.
- An electric shock or a fire may take place if it
catches flame.
• Stay away from the washer when the bottom of
the washer sinks into the water.
- There might be an electric shock. Please wait
until the water drains out completely.
• If the washer makes strange noise, smell or
smoke, unplug it promptly and call service agent.
- An electric shock or a fire may take place.
• Do not put laundry stained with gasoline,
benzene, or alcohol in the washer, and keep the
materials away from the washer.
• When cleaning, don’t spray water to the parts of
the washer directly.
- An explosion or a fire may take place.
- It may make it’s life span shorten.
Also an electric shock or fire may take place
• During spinning, don’t put your hand in the
spinning tub.
- It may hurt your hands. If it does not stop within
15 seconds after you open the lid, call service
agent immediately.
• Don’t use several appliances together with an
outlet.
- A fire may take place due to unusual heat.
• This appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they can use the appliance safely.
Young children should be supervised to ensure
that they do not play with the appliance.
• Don’t press the button with an awl or pin.
- An electric shock or a fire may take place.
• Use the new hose-sets and old hose-sets should
not be reused.
• This appliance has to be connected to the plug
endurable to proper power consumption.
• If the damage is found on the current cord in use,
it should be replaced by manufacturer, service
cener or authorized person in order to avoid the
risk.
• This appliance has to be positioned so that the
plug is accessible after installation.
• No user-serviceable parts inside. Refer any servicing
to qualified service personnel.
• Connect the grounding wire to the shell plate, and
bury it under at least 25cm of earth:elternatively,
connect the ground wire to the appropriate pin on
a properly grounded power receptacle. Never
connect the wire to a telephone line, lightning rod,
or gas pipe.
- Otherwise this may cause a mechanical error,
electric shock, fire or physical damage.
- The product warranty does not cover problems
resulting from disassembling the product.
• Do not use this product for business purposes.
• For washing machines with ventilation openings in
the base, that a carpet must not obstruct the
openings.
3
SW68ASP-02290A-EN.indd
3
2006-08-21 ¿ÀÈÄ 8:33:08
INSTALLATION &MAINTENANCE
ENVIRONMENT
IN CASE OF PUMP-DRAINED WASHER
Leave some space.
Takeoutthe Be sure to join tightly Install the drain
Maintain at least 10cm between the washer and the wall.
cap-hose and
connect the
outlet-hose
the drain hose into the
drain-outlet on the left
side of the machine.
hose in the position
of about 70~80cm
above the ground.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak
surface, noise and vibration can occur
(allowable slope is 1 degree)
Never install the washer in a very steamy
environment or where it might be open to the rain.
Excessive moisture may cause an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected
by direct heat,never place the washer near furnaces,
boilers,etc.Do not place under direct sunlight.
HOW TO CONNECT WATER SUPPLY HOSE
Checkthetypeoftapfittingwhichisinyourlaundryandthenseeappropriateinstructionbelow:
A tap of ordinary type is desirable In case of square tap
ake out the internal part of the connector
T
and join it in the following way.
Internal part
ORDINARY TAP SQUARE TAP
ROTATING TAP
1.Remove the adaptor from the
water supply hose.
4.Connect the water supply hose to
the adaptor. Pull down the part
(c) of the water supply hose .
When you release part (c) the
hose is automatically connects to
the adaptor making a 'click' sound.
2. First,using a "+" type screw
driver, loosen the four screws on
the adaptor.
5. Connect the other end of the water
supply hose to the inlet water valve
at the top of the washer.
Next,take the adaptor and
turn part(b) following the
arrow for gap about 5mm
between them.
Screw the hose clockwise all the
way in.
3. Connect adaptor to the water
tap by tightening the screws
firmly.
6. If the water tap is a screw type,
assemble a water supply hose that
fits to the tap as shown.
Then,turn part (b) following
the arrow and put (a) and
(b)together.
Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not
be used.
4
SW68ASP-02290A-EN.indd
4
2006-08-21 ¿ÀÈÄ 8:33:11
HOW TO CLEAN THE FILTER
CLEANING THE FILTER (pump drained washer)
Clean the filter net often to keep the washer clean.
1. Place a rag under washer filter not to wet the floor.
2. Turn the filter-cap to the left.
3. Take out the filter and remove any sludge.
4. Reassemble in reverse order.
1. Push the upper 2. Open the cover 3. Clean the filter. 4. Close the cover and
part of the filter
and pull in.
as shown in the
figure.
insert the lower part
of the filter in the
basket first and then
push the filter with
"click" sound .
HOW TO ADD THE DETERGENT
1. Open the detergent box
by pulling in the direction of the
arrow as shown in the figure.
2. Add the amount of detergent for one
washing evenly in the box so that the
detergent does not overflow the box.
LEVELLING
1. Pull down the adjusting handles of
the adjusting feet which are located
at the right and left of the front side.
2. Adjust the height of the
HOW TO ADD THE FABRIC SOFTENER
machine upwards or downwards.
3. When the adjustment is finished,
push back the handles to fix the
When a proper amount of fabric softener is stored
in the box, it is automatically added in at the
final rinse cycle.
In case the hot water only is connected,
this function will not be operated.
adjusting feet.
Note
Do not kick or step on the adjusting
handles.
When too much softener is stored above the
base line, it may not be operated properly.
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
Open the lid of the machine, pour water into the tub
up to the level just below the pulsator, and adjust the
legs so that the pulsator is positioned at the center of
the water as shown in the figure.
Place the machine more than 10cm away from the
wall.
5
SW68ASP-02290A-EN.indd
5
2006-08-21 ¿ÀÈÄ 8:33:13
PRECAUTIONS
WARNING! NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY
LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK.
Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine.
How to earth an outlet with earthing terminals
when an earthed power load is not fitted.
Outlet with earthing terminals:
Even when the internal wires of the earthing terminals are
joined, connect the earthing conductor (green) of the
machine to the tap.
When using an extension cord and a boosting transformer:
Make sure that the earthing conductor is connected.
Never make an earthing to
The telephone line, lightning rod, or gas pipe as it is
extremely dangerous in case of lightning strikes.
TO DO A CLEAN WASHING
Press the POWER botton.
Pour a little detergent into case-detergent.
Turn on water supply to the wshing machine.
Choose the SOAK in CYCLE button and the HIGH in WATER LEVEL button.
Press the START/PAUSE button.
6
SW68ASP-02290A-EN.indd
6
2006-08-21 ¿ÀÈÄ 8:33:14
CONTROLPANEL
Formoredetails,seecontrolpanelofyourwashingmachine.
1. POWER BUTTON
Press this button once to operate.
Press once again to turn the power off.
2. START/HOLD BUTTON
Use to pause and restart the operation.
To change the washing procedure during operation, press this button to stop, and once again to restart after
changing the procedure.
3. DELAY START BUTTON
Press this button when delay start washing is needed.
4. PROGRAM BUTTON
With every press of this button, the washing course changes;
SENSOR HEAVY DUTY ECONO WASH WOOL DELICATE SENSOR
5. SUPER CLEAN BUTTON
Press the button once to perform SUPER CLEAN.
To release the function, change the course by pressing a Program button, or press the Cycle Select button.
6. CYCLE SELECT BUTTON
With every press of this button, the function changes:
SOAK&WASH&RINSE&SPIN WASH RINSE SPIN RINSE&SPIN WASH&RINSE&SPIN
SOAK&WASH&RINSE&SPIN
7. WATER LEVEL SELECT BUTTON
According to the wash load, select the water level;
AUTO EXTRA LOW LOW MEDIUM HIGH
8. TEMPERATURE SELECT BUTTON
As you press this button, the type of water is selected as follows.
COLD COLD + HOT HOT COLD
9. REMAINING TIME INDICATOR LIGHT
The indicator light shows the remaining time (in minutes) of each wash cycle.
At the end of the cycle, the power automatically switches off.
7
SW68ASP-02290A-EN.indd
7
2006-08-21 ¿ÀÈÄ 8:33:16
WASHINGINSTRUCTION
PROCEDURE
1. Sort the laundry into separate wash loads.
Each load of washing should contain clothing which needs the same washing conditions.
For example, you should not wash delicate clothes with very dirty work clothes.
2. Load the laundry into washing.
Before load, check all pockets, and close zippers, hooks and eyes.
3. Add the detergent.
4. Add the fabric softener.
5. Close the lid.
6. Press power button.
7. Choose the wash program & optional cycle.
If you choose “SENSOR”program you don’t need to select water level.
Water level is set automatically at “SENSOR”program.
Press the START/PAUSE button.
8. Select the water level.
Before choosing the water level, remember following things.
When you choose SENSOR, HEAVY-DUTY, ECONO-WASH, DELICATE program,
water level is selected “AUTO”automatically, but if you want to choose water
level manually you can select. HIGH, MEDIUM, LOW, EXTRA LOW
9. Select the water temperature.
Before choosing thr water temperature remember the following:
1) You can choose HOT, HOT+COLD, COLD on all programs except for delicate program.
HOT is hot wash and cold rinse.
COLD is cold wash and cold rinse.
2) When you choose delicate program, water temperature is selected automatically.
10. Close the lid and press the START/PAUSE button.
11. Do you want extra rinse?
For extra rinses press the cycle key 1 to 5 times
(depending on the number of extra rinses required).
You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key.
The time left display will show the number of rinses selected.
Note that the extra rinse program is not available when pause is selected or during the spin cycle.
WASH PROGRAM
SENSOR
18 min
Normal
HEAVY DUTY
21 min
ECONO WASH
18 min
WOOL
6 min
DELICATE
6 min
SUPER CLEAN
6 min
Wash Time
Wash Action
Normal
Normal
Gentle
Gentle
Normal
HOT
HOT + COLD
COLD
HOT
HOT + COLD
COLD
HOT
HOT + COLD
COLD
HOT
HOT + COLD
COLD
Wash Temp.
HOT + COLD HOT + COLD
COLD COLD
HOT + COLD HOT + COLD
Deep Rinse
Spin Time
COLD
6 min
COLD
6 min
COLD
6 min
COLD
6 min
COLD
COLD
6 min
6 min
Total Time
(High Water
level)
56 min
59 min
55 min
8
41 min
42 min
60 min
SW68ASP-02290A-EN.indd
8
2006-08-21 ¿ÀÈÄ 8:33:18
WASHINGPROGRAM
SENSOR Program
HEAVY DUTY Program
The best washing program is chosen automatically
Load size and water level is determined automatically
Unplug the power cord after washing.
This program is suitable for heavily soiled laundry
Load size and water level are determined utomatically
or you can choose the water level you want
Unplug the power cord after washing.
ECONO WASH Program
WOOL Program
This program is suitable for woollen clothes
Only high and medium water levels are available
Saving your time and energy
This program is suitable for saving water consumption
Load size and water level are determined automatically
or you can choose the water level you want
Unplug the power cord after washing.
Unplug the power cord after washing.
DELICATE Program
Washing action is very gentle, so this program is suitable for
delicate clothes like lingerie.
Load size and water level are determined automatically
or you can choose the water level you want
Unplug the power cord after washing.
OPTIONALCYCLE
SOAK
WASH ONLY
When you choose this cycle, only wash cycle is operated.
Pressing optional cycle key during washing changes the wash
time in two minute intervals.
The wash time can be changed to between 3 and 25 minutes.
Load size and water level is determined automatically.
Unplug the power cord after washing.
The laundry is soaked in water so that heavy dirt can be
eliminated sufficiently.
You can choose soak cycle after choosing wash program.
When you select soak function, 5 minute cycle (1 min. washing
then 4 min. pause) continue for 30 minutes before main wash
program.
Load size and water level is determined automatically.
Unplug the power cord after washing.
RINSE ONLY
SPIN ONLY
When you choose this function, only rinse cycle is operated.
Pressing function key during rinsing changes the number of
rinses. Up to 5 rinses can be optionally selected.
Unplug the power cord after washing.
When you choose this cycle, only spin cycle is operated.
Pressing cycle key during spinning only cycle changes the
spin dry time.
The spin dry time can be changed to between 1 and 7 minutes.
Unplug the power cord after washing.
DELAY START
This function allows you to delay the start of your chosen wash
program for 3, 4, ... 18 hours.
RINSE AND SPIN ONLY
When you choose this cycle, only rinse & spin cycle are operated
without wash cycle.
By pressing the delay start key you can select delayed period for When the CYCLE button is pressed during operation, the rinse
3, 4, ... 17, 18 hours, and your washing machine will finish
the selected wash program after the delayed period.
times can be changed to between 1 to 5 times in duration.
Unplug the power cord after washing.
SUPER CLEAN
If you pressing the Super Clean button after selecting a program, the program changes to the Super Clean course.
To release the function, change the course by pressing a program button, or press the Cycle Select button.
When Super Clean is selected, the total time is extended with the addition of a specific period of time.
When Super Clean is selected, the LOW water level is selected by default and detecting the volume of laundry is skipped.
The wash proceeds in five steps. (You can only select HIGH, MEDIUM, or LOW for the water level.)
CHILD LOCK
This is a device to protect children from being accidentally hurt while playing with the washer.
How to start the Child-Lock function:
- Press the “Power”button to go to an initial washing mode.
- By pressing “Start/Hold”button, you start washing and in case Child Lock function is needed during the laundry
- Press both the “Water level”and “Function”buttons at the same times. (for 3 seconds)
(Note: You cannot perform the function without the “Power”button on.)
In the event that you would like to modify the Child-Lock function, “L”signal flashes in the “signal window showing the rest of the set
time”every two seconds, which means it is locked and indicates how much time is left until the function is released.
To release the function of Child-Lock:
- In case the “Child-Lock”is programmed, press both the “Function”and “Water level”buttons at the same time.
9
SW68ASP-02290A-EN.indd
9
2006-08-21 ¿ÀÈÄ 8:33:18
TROUBLESHOOTING
Spinning does not work
Washing machine won’t work
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is the laundry spread out evenly
in the washer?
Is the washer set on a sturdy
flat surface?
Is the fuse all right?
Is there enough water?
Is the lid closed?
Water does not drain
Water is not supplied
Is the drain hose down? (No pump)
Is the drain hose frozen?
Is the water tap opened?
Is the water cut off?
Is the drain hose clogged?
If the water does not drain in 15
minutes, a buzzer will sound,
and the remaining time
Is the water supply hose or hose
connection clogged?
Is the water tap frozen?
If water is not supplied in 60
minutes, a buzzer will sound,
and the remaining time indicator
will shown “4E”.
indicator will show “5E”
While lid is opening, the washing
machine won’t work
Water is overflowed
Restart after spinning.
If the error sign still indicates,
call agency.
Make sure to close the lid while washing
machine is operating.
SPECIFICATION
SW68ASP
6.5
SW57APP
Load capacity(kg)
Bowl
5.5
Stainless Steel
PP
Power input(Watts)
Size (WxDxH)(mm)
Net Weight (kg)
450
600x660x1010
48
Water Consumption(liters)
Water Pressure(min-max)
134(high)
137(high)
50~780KPa
10
SW68ASP-02290A-EN.indd 10
2006-08-21 ¿ÀÈÄ 8:33:19
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Samsung Electronics Australia
1300 362 603
SW68ASP-02290A-EN.indd 11
2006-08-21 ¿ÀÈÄ 8:33:20
|