Samsung Security Camera SCC B5396 User Guide

SCC-B5396  
SCC-B5398  
DIGITAL COLOR DOME  
CAMERA  
user manual  
imagine the possibilities  
Thank you for purchasing this Samsung product.  
To receive more complete service,  
please register your product at  
 
Safety information  
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately  
disconnect the power source and contact the service center. Continued use in such a condition may cause  
fire or electric shock.  
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify  
this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or  
attempted repair.)  
S
10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.  
CAUTION  
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to  
excessive vibrationor magnetic interference.  
nt  
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high  
humidity. Doing so may cause fire or electric shock.  
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall  
it.  
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or  
damage to the product.  
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.  
6. Install it in a place with good ventilation.  
er  
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the  
CCD image sensor.  
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,  
shall be placed on the apparatus.  
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.  
English 3  
 
Important Safety Instructions  
WARNING  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
s
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including  
amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide  
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult  
an electrician for replacement of the obsolete outlet.  
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and  
the point where they exit from the apparatus.  
11.Only use attachments/accessories specified by the manufacturer.  
12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or  
sold with the apparatus.  
13.Unplug this apparatus when a card is used. Use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been  
damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have  
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or  
has been dropped.  
4 – DIGITAL COLOR DOME CAMERA  
 
s
Contents  
Introduction  
Features  
Product & Accessories  
Part Names and Functions  
6
7
8
Installation  
s
Installation procedure  
Adjusting the camera direction  
11  
12  
How to use OSD Menu  
Using Icons in the Menu  
Main Menu  
14  
14  
15  
17  
24  
27  
28  
29  
29  
e
Profile  
Camera Setup  
Intelligence  
nd  
Privacy Zone Setup  
Other Set  
System Information  
Language  
Specifications  
Specifications  
30  
ve  
or  
English 5  
 
Introduction  
FEATURES  
C
High Resolution  
This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special  
algorithm technologies.  
Intelligent Motion Detection & Tracking  
This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it displays an  
alert if an object passes / enters /exits the virtual fence or virtual area.  
XDR (eXtended Dynamic Range)  
Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel  
unit to determine the optimal visibility.  
High Sensitivity  
It implements images of high sensitivity using the up-to-date SONY Super-HAD IT CCD..  
Low Illumination  
It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify  
objects even in the worst environment.  
Superior Backlight Adjustment  
When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object  
picture quality.  
Digital Power Synchronization  
The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operationability  
and reliability of this camera.  
Output Signal Setting  
You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/  
Vertical profiling, and digital zooming.  
OSD(On Screen Display) Menu  
OSD menu is provided to display the status of camera and to configure the functions interactively.  
Coaxial Cable Communication  
This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the  
control signal. In installation or repair, this helps you control the communication controller (optional) without  
additional cabling.  
6 – DIGITAL COLOR DOME CAMERA  
 
Introduction  
Components  
Checking components in the package  
Camera  
Test Monitor Cable  
User’s Guide  
Image  
Part name  
Standard  
Quantity  
4 (EA)  
8
Usage  
Attach each piece to screw connection holes for  
strengthening connection  
Plastic anchor  
HUD 5  
BH M5 X L6.  
(White+o-ring)  
ASSY screw  
machine  
Used for lling in the holes when installing  
pipe and wall mount  
TH M4xL30 (Black+  
o-ring)  
ASSY screw  
tapping  
Used when installing your camera on the  
4
1
ceiling or wall。  
Used for assembling/disassembling the  
Dome cover  
L-Wrench  
TROX T-20  
Template  
1
1
Used for guiding the installation  
Used to make a wiring hole when installing  
the camera on the ceiling or wall  
Gasket-pipe hole  
T2.5 W56  
NOTE  
The test monitor cable is used to test the camera by connecting to a portable display. If you  
really want to connect the camera to a monitoring display, use the BNC cable.  
English 7  
 
Introduction  
Components of your camera  
Dome cover: Covers the inner cover, lens, and  
1.  
main body to protect them.  
Your camera has the following components:  
Cover screw: Use it to assemble or  
2.  
disassemble both dome cover and case.  
Inner cover: Covers the main body to protect it.  
3.  
1
3
.Wing locker: Push a long thin screwdriver into  
4
its narrow spot and press it outward when you want  
to remove the inner cover.  
Main body: Includes a lens, a switch board, a  
5.  
PCB board, screws, and such.  
2
4
5
Screws for assembly and disassembly: Using  
6.  
these 2 screws, the Main  
7
body is closely connected to the Case.  
6
6
Hooker: By pulling the left/right levers in the  
7.  
arrow direction, the Main body can be detached  
from the Case.  
7
Case: Used as a ceiling or wall xture. It is  
8.  
8
xed using four screws provided in the package.  
Zoom lever: Using this lever, the lens zoom can  
9.  
be adjusted and xed.  
Focus lever: Using this lever, the lens focus can  
10.  
be adjusted and xed.  
Lens  
Tilt xing screw: Using this screw, the slope of  
11.  
the lens can be adjusted and xed.  
Cable: Connect the Video connector to BNC  
12.  
cable and Power connector to power adapter.  
9
10  
11  
12  
Video connector  
Power connector  
8 – DIGITAL COLOR DOME CAMERA  
 
Introduction  
Setting switches  
SETUP Switch  
This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the  
MAIN MENU appears.  
ef (Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the  
displayed value.  
cd (Up/Down) : By pressing this switch up or down, you can move up or down on the menu.  
: When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press  
this button..  
English 9  
 
Installation  
Installing camera  
Before installation  
B
a
T
1.  
Before installing your camera, you have to read the following cautions:  
You have to check whether the location (ceiling or wall) can bear ve times the weight of your camera.  
Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may  
cause a breakdown or re. You can use wall mount adaptor (SADT-102WM), and pole mount adaptor (SADT-  
100PM) for installing the camera on the wall or pipeline.  
When installing your camera, don’t allow any person to approach the installation site. If you have any valuable  
em away.  
things under the place, move th  
About the installation holes  
A:Use these holes when directly installing your camera on the ceiling or  
wall.  
While those are not used, ll in the holes using the screw machine (M5  
X L6.) for waterproong.  
Bottom of camera  
B: Use four holes when directly installing your camera on the junction box  
You can use the 4 1/8 diameter round type junction box for assembly.  
(The junction box, gasket, and cover are separately purchased items.)  
2
A
B
C: Use these holes when installing the wall mount adapter (SADT-  
102WM)  
While those are not used, ll in the holes using the screw machine (M5  
for waterproong.  
X L6.)  
The holes that are not used should be tightly  
sealed up using the screws provided for  
waterproong. When the screws don’t have rubber  
rings inside or are not closely attached, note that it  
can cause waterproong problem.  
C
F o r a t t a c h i n g s c r e w s , s e e p a g e 1 6  
“Disassembling/assembling the Main body from  
the Case.”  
10 – DIGITAL COLOR DOME CAMERA  
 
n
Installation  
Installing on a pipe  
Before installation, you have to be familiar with the above cautions and ll in the holes that  
are not used for installation.  
To install your camera bottom on a pipe  
3. Attach the Dome cover. (Screw the connection bolts  
tightly using the L-Wrench for waterproong.)  
1.  
After connecting the power and video cables,  
To change the SAMSUNG logo position, move the  
location of the connection rubber band as show  
below and rotate for assembly. (The rotation limit  
is 180 degree.)  
throw them inside the pipeline and screw the male  
thread pipe into the female pipe thread in your  
camera tightly to fix the Main body. (In this case,  
be sure to tape with Teon tape before assembly for  
waterproong. Be careful for the wiring cable not to  
be stuck in the connection area.)  
2. Adjust the angle of the camera in search of a better  
view.  
1) Separate the Dome cover using the L-Wrench  
provided. (To make loose the screws, rotate  
counterclockwise.)  
2) Adjust the lens direction. For more information,  
see page 17 “Adjusting the camera direction.”  
English 11  
 
Installation  
When the camera is xed on the ceiling, you can adjust the camera viewing angle.  
You can rotate your camera leftward or rightward (Panning), and can change the  
slope of your camera upward or downward (Tilting).  
H
Adjusting the camera direction  
U
In case of panning, the rotation limit of your camera is set to 355 degree (100  
degree clockwise and 255 degree counterclockwise). The rotation is stopped by  
the Stopper inside of the camera. For panning control, rst unfasten two screws  
located on the bottom and rotate in the direction you want, and then fasten them to  
x the camera.  
In case of tilting, you can change the slope of your camera from zero to 90 degree.  
However if the slope angle is under 17 degree, you can encounter a partial image  
hide problem. To x the location after adjusting the tilting angle, use the Tilt fixing  
screws.  
To adjust the focus and zoom of your camera, use the Zoom lever and Focus  
lever. When you install the camera on the inclined ceiling or wall, you can rotate the  
camera lens to see a correct direction image.  
Panning  
Tilting  
Lens rotation  
12 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
USING ICONS IN THE MENU  
MAIN MENU  
e.  
e
(EXIT)  
ꢃꢃMAIN MENUꢃꢃ  
PROFILE  
CAMERA SET  
INTELLIGENCEꢅ  
PRIVACY ZONEꢅ  
OTHER SETꢅ  
Exits the menu setting.  
Before you exits the menu setting, select SAVE to  
save your settings, or select QUIT to cancel.  
0
by  
ws  
to  
(RET)  
Returns to the previous menu.  
SYSTEM INFOꢅ  
LANGUAGEꢅ  
(HOME)  
e.  
e
g
Returns to the main menu.  
(SAVE)  
PROFILE  
You can set a mode according to the camera  
Used to save your settings of MASK AREA,  
PRIVACY ZONE and more.  
installation conditions.  
us  
e
Once you save your settings, they will remain  
even if you select QUIT in the menu.  
CAMERA SET  
Configure Camera related functions and data.  
(DEL)  
INTELLIGENCE  
You can configure the settings of motion  
detection, tracking and more.  
Used to deletes your settings of MASK AREA,  
PRIVACY ZONE and more.  
Once you delete your settings, they will not be  
restored even if you select QUIT in the menu.  
PRIVACY ZONE  
You can configure the privacy related settings.  
OTHER SET  
You can configure for Factory Defaults, and more.  
SYSTEM INFO.  
Displays the system information including the  
camera version and communication settings.  
LANGUAGE  
Select a preferred one from the supported  
languages.  
English 13  
 
How to use OSD Menu  
PROFILE  
e
PROFILEf  
STANDARD  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
CUSTOM  
In the PROFILE menu, you can configure the following camera settings at once.  
CAMERA SET Menu  
STANDARD  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
Previous  
Menu  
Sub-menus  
IRIS  
ALC  
-
ALC  
-
ALC  
-
ALC  
-
ALC  
-
ALC  
LENS  
DC  
DC  
DC  
DC  
DC  
LEVEL  
0
0
0
0
0
BACKLIGHT  
OFF  
OFF  
BLC  
NORM  
MID  
OFF  
AUTOx4  
MID  
OFF  
OFF  
SLOW  
MID  
OFF  
AUTOx4  
MID  
MOTION  
DNR  
(F.FAST)---  
MID  
(F.FAST)---  
MID  
(F.FAST)---  
MID  
SHUTTER  
SENS-UP  
XDR  
OFF  
AUTO1/250  
AUTOx2  
MID  
OFF  
AUTOx4  
MID  
AUTOx4  
MID  
DAY/  
NIGHT  
AUTO  
AUTO  
DAY  
AUTO  
DAY  
NIGHT  
BURST  
-
-
-
-
-
OFF  
ON  
OFF  
OFF  
OFF  
14 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
CAMERA SET Menu  
STANDARD  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
Previous  
Menu  
Sub-menus  
WHITE  
BAL  
DAY  
DAY/NIGHT  
DAY  
DAY/NIGHT  
DAY  
DAY  
-
-
-
-
-
MODE  
RED  
ATW2  
ATW1  
ATW1  
ATW1  
ATW1  
0
0
-
0
0
-
0
0
-
0
0
-
0
0
-
BLUE  
NIGHT  
User setting  
allowed  
User setting  
allowed  
User setting  
allowed  
BRIGHTNESS  
MODE  
MID  
ATW2  
0
MID  
ATW2  
0
OFF  
OFF  
OFF  
User setting  
allowed  
User setting  
allowed  
User setting  
allowed  
RED  
User setting  
allowed  
User setting  
allowed  
User setting  
allowed  
BLUE  
0
2
0
2
DETAIL  
2
2
2
ITS  
It will be set automatically so you can easily check the traffic conditions.  
BACKLIGHT  
It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.  
DAY/NIGHT  
It will be set automatically so it optimizes to the day or night conditions, respectively.  
GAMING  
It will be set automatically to help you take a picture in a regular indoor lighting condition.  
English 15  
 
How to use OSD Menu  
Setup the general functions of zoom camera module.  
Use the cdef switch to select a menu item.  
CAMERA SETUP  
eCAMERA SETf  
CAMERA ID  
[OFF, ON]  
CAMERA ID  
IRIS  
MOTION  
DNR  
SHUTTER  
SENS-UP  
FLICKERLESS  
XDR  
OFF  
ALCꢅ  
(F.FAST)---  
CAMERA IDꢀ  
ABCDEFGHIJKLMNOPQRSTUVWXYZ0  
123456789 :?-+*()/  
MID  
OFF  
AUTO X4  
(OFF)---  
MID  
SPffeeSP LOCATION  
CAMERA-1..................  
d
...........................  
c
DAY/NIGHT  
WHITE BAL  
DIGITAL ZOOM  
DETAIL  
V-SYNC  
AGC COLOR SUP  
REVERSE  
POSI/NEGA  
PIP  
AUTOꢅ  
OFF  
The CAMERA ID menu is used for you to assign  
a unique name to a camera. If you press the  
SETUP switch with the CAMERA ID menu  
selected, you will see the appropriate screen.  
[2]  
INT  
LOW  
H/V  
+
OFF  
You can enter up to 54 alphanumeric or  
special characters for the CAMERA ID. Select  
LOCATION and press the SETUP switch to  
move the display position of the CAMERA ID.  
d
c
IRIS  
[ALC]  
DIS  
OFF  
The IRIS menu is used if you want to adjust the  
intensity of radiation incoming to the camera.  
ALC (Automatic Light Control)  
If you press the SETUP switch with an ALC-  
based sub menu selected, you will see the  
appropriate screen.  
16 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
.
displayed dark on the monitor affected by the  
backlight. To solve this problem, you can use  
the BLC(Back Light Compensation) function  
to improve the sharpness of the image in  
such a high contrast scene.  
ALCꢀ  
[00]----I----  
LEVEL  
BACKLIGHT  
OFF  
AGC  
[OFF, VERY LOW, LOW, MID, HIGH, VERY  
HIGH, USER, FIX]  
The AGC (Auto Gain Control) menu is used to  
set the AGC level of the camera. When the AGC  
is active, the camera automatically increases the  
sensitivity by amplifying the Video signal when  
the strength of the signal falls below the normal  
value.  
The LEVEL menu is used to adjust the  
overall brightness, where “+” will increase the  
brightness and “–” will decrease it.  
If you set the BACKLIGHT option to BLC,  
you will see a menu where you can set the  
BLC area.  
n
If OFF or FIX mode is selected in the SENS-UP  
menu, you can specify the AGC level.  
If you press the SETUP switch with a USER  
sub menu selected, you will see the appropriate  
screen.  
you can set the desired BLC zone by defining  
the size and location.  
ALCꢀ  
AGC USERꢀ  
LEVEL  
BACKLIGHT  
AREA  
[00]----I----  
BLC  
LEVEL  
[16]  
USER  
<SIZE>  
<LOCATION>ꢅ  
-
In USER mode, you can break down the level in  
16 steps from VERY LOW to VERY HIGH to your  
preference.  
If you use an ordinary camera in a scene  
with an intensive backlight, the object will be  
English 17  
 
How to use OSD Menu  
Note :  
If the DAY/NIGHT menu of the CAMERA SET is set to  
AUTO, the MOTION menu will be deactivated.  
AGC FIXꢀ  
[01]  
LEVEL  
DNR  
[OFF,LOW,MID,HIGH, USER(1~16)]  
You can configure the DNR (Digital Noise  
Reduction) related settings.  
Reduces the noise on the screen.  
This is especially useful for a severely distorted screen.  
If you press the SETUP switch with a FIX sub  
You can set the level if you set DNR to USER.  
menu selected, you will see the appropriate screen.  
SHUTTER  
As a fixed value of the AGC gain is used in FIX  
mode, you can select one of the 16 detailed levels  
from VERY LOW to VERY HIGH before fixing it.  
[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,  
AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO  
1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,  
1/500, 1/1000, 1/2000, 1/4000, 1/10K]  
Note :  
The SHUTTER menu is used to configure settings  
of the fixed / auto high-speed electronic shutter.  
If the DAY/NIGHT menu of the CAMERA SET is set to  
AUTO, the AGC menu will be deactivated.  
You can select one of 7 options from 1/100(PAL:1/120)  
to 1/10K for the fixed high speed electronic shutter,  
which is mostly used for imaging a fast moving object.  
If FLICKERLESS is set to ON, the AGC FIX mode will be  
disabled.  
The auto high speed electronic shutter operates  
as the fixed high speed shutter in a high contrast  
scene but automatically focuses the target if the  
iris opens fully in a low contrast scene like in ELC  
mode. When it gets brighter back, the mode will  
switch to the fixed high speed electronic shutter  
mode.  
MOTION  
[S.SLOW, SLOW, NORM, FAST, F.FAST]  
The MOTION menu is used to adjust the strength  
of the AGC level for a control of the camera motion.  
This is available only if the SENS-UP menu is set  
to AUTO.  
You can select one from S.SLOW, SLOW, NORM,  
FAST and F.FAST for the AGC level.  
However, the auto high speed shutter operates  
properly only in a camera featuring a DC or VIDEO  
lens.  
If you monitor a fast moving object in a low contrast  
scene, select F.FAST while select S.SLOW for a  
hardly moving object in the same lighting condition.  
18 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
Note :  
FLICKERLESS  
[OFF, ON]  
If the SENS-UP function is set to AUTO, only items of  
If set to ON, the shutter speed will be fixed to  
OFF and AUTO are available in the SHUTTER menu.  
1/100(PAL:1/120) second. This will prevent possible screen  
distortion due to a mismatch between the vertical sync  
frequency and the blinking frequency of the lighting.  
If the SENS-UP mode is set to FIX, the SHUTTER menu  
will be deactivated.  
If the FLICKERLESS function is set to ON, the SHUTTER menu  
will be deactivated.  
Note :  
If the SHUTTER menu is set to AUTO or FIX mode, the  
FLICKERLESS menu will not be available.  
SENS-UP  
en.  
If the SENS-UP function is set to FIX mode, the Flickerless  
menu will be deactivated.  
[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO  
X8, AUTO X12, AUTO X16, AUTO X24, AUTO  
X32, AUTO X48, AUTO X64, AUTO X96, AUTO  
X128, AUTO X256, AUTO X512, FIX X2, FIX  
X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24,  
FIX X32, FIX X48, FIX X64, FIX X96, FIX X128,  
FIX X256, FIX X512]  
If AGC is set to FIX mode, the FLICKERLESS function will  
be disabled.  
XDR (eXtended Dynamic Range)  
[OFF, LOW, MID, HIGH]  
O
Actively controls the gamma compensation in the  
way it operates the ambient luminance contrast  
in a certain pixel unit to determine the optimal  
visibility.  
Automatically detects the ambient level of  
darkness in the dark or low contrast scene to  
extend the accumulated time, keeping the image  
bright and sharp; It can be also used as FIX  
mode.  
s
0)  
.
Select one from OFF, LOW, MID and HIGH.  
Closing to HIGH will increase the compensation  
level.  
Note :  
If the SHUTTER menu is set to fixed electronic shutter  
DAY/NIGHT  
[DAY,NIGHT,AUTO,EXT]  
mode, the SENS-UP menu will not be available.  
If FLICKERLESS is set to ON, the FIX mode of the SENS-  
UP menu will be disabled.  
DAY  
If set to DAY, it will be fixed to DAY mode  
regardless of the ambient conditions.  
If the SHUTTER menu is set to AUTO, the SENS-UP  
menu can be set to either OFF or AUTO mode.  
NIGHT  
If set to NIGHT, it will be fixed to Black-and-White  
mode regardless of the ambient conditions.  
O
English 19  
 
How to use OSD Menu  
If you press the SETUP switch with a NIGHT sub  
menu selected, you will see a menu where you can  
set Burst to OFF/ON.  
If BURST is set to ON, the Burst signal will output  
together with the black-and-white composite video  
signal. If BURST is set to OFF, the Burst signal does  
not output.  
You can set the BURST option to OFF/ON, or  
select to output the Burst signal in NIGHT mode.  
for which you can select from LOW, MID, and  
HIGH. As you adjust it from HIGH to LOW, the  
screen switches to black and white mode under  
the darker situation.  
DWELL TIME of DAYÆNIGHT sets the time to  
maintain switched black and white mode.  
The BRIGHTNESS of NIGHTÆDAY sets the  
brightness degree of BW to color switching,  
for which you can select from LOW, MID, and  
HIGH. As you adjust it from HIGH to LOW, the  
screen switches to color mode under the darker  
situation.  
AUTO  
The camera will automatically switch between  
DAY and NIGHT mode, according to the lighting  
condition.  
DWELL TIME of NIGHTÆDAY sets the time to  
maintain switched color mode.  
If you press the SETUP switch with an AUTO-  
based sub menu selected, you will see the  
appropriate screen.  
The MASK AREA menu is used to prevent  
unintended mode switching or inability of  
determining the switching due to existence of  
high spot light source at night.  
AUTOꢀ  
BURST  
OFF  
If you press the SETUP switch in item 1 or 2 of  
the MASK AREA menu, you will see a menu  
where you can specify an area to MASK.  
DAYÆNIGHT  
BRIGHTNESS  
DWELL TIME  
NIGHTÆDAY  
BRIGHTNESS  
DWELL TIME  
MASK AREA  
MID  
2S  
MID  
5S  
2
MASK AREAꢀ  
1
<SIZE>  
<LOCATION>ꢅ  
You can set the BURST option to OFF/ON, or  
select to output the Burst signal in NIGHT mode.  
The BRIGHTNESS of DAYÆNIGHT sets the  
brightness degree of color to BW switching,  
20 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
You can specify MASK 1 and 2 simultaneously.  
The MASK is only for determining the mode  
switching, and any excessive bright area at night  
will be excluded by the configured MASK.  
NIGHT  
Use the NIGHT mode if you want to set the white  
balance differently according to the ambient  
luminance.  
If the NIGHT mode is set to OFF, the white  
balance will always operate as set in DAY mode;  
if not to OFF, the camera will switch to as set in  
DAY/NIGHT mode according to the brightness.  
In NIGHT mode, you can set the values of RED,  
BLUE and BRIGHTNESS. The screen will be  
displayed in colors according to your settings.  
r
o
Note :  
If BACKLIGHT is set to BLC, the MASK AREA function will  
be deactivated.  
WHITE BAL  
[DAY/NIGHT]  
If you want to adjust the color scheme, use the  
WHITE BALANCE function.  
r
DAY  
o
WHITE BALꢀ  
In DAY mode, you can set the color values of  
RED and BLUE. The screen will be displayed in  
colors according to your settings.  
DAY/NIGHT  
BRIGHTNESS  
MODE  
NIGHT  
MID  
AWCꢅ  
RED  
[00]----I----  
[00]----I----  
[0248]  
WHITE BALꢀ  
BLUE  
R-GAIN  
B-GAIN  
DAY/NIGHT  
MODE  
DAY  
AWCꢅ  
[0247]  
RED  
[00]----I----  
[00]----I----  
[0248]  
BLUE  
R-GAIN  
B-GAIN  
[0247]  
Note :  
You can set the values of R-GAIN and B-GAIN only in  
AWC mode.  
If AGC is set to OFF or FIX, you can not access the  
NIGHT menu.  
Note :  
You can set the values of R-GAIN and B-GAIN only in  
AWC mode.  
For adjusting the white balance, the following  
5 modes are provided:  
English 21  
 
How to use OSD Menu  
ATW1(Auto Tracing White Balance mode  
1): The camera can automatically adjust the  
color temperature in real time, according to  
the ambient conditions. The color temperature  
ranges from approx. 2500K to 9300K.  
DIGITAL ZOOMꢀ  
RATIO  
[X1.0]  
< LOCATION >  
ATW2: The color temperature ranges from  
approx. 2,000K to 10,000K.  
AWC ( Auto White Balance Control): If you  
press the SETUP switch in the appropriate item  
position, Auto White Balance will perform once.  
3200K : Set color temperature to 3200K  
-
LOCATION : If you press the SETUP switch in the  
condition where the image is enlarged as much as the  
ratio setting, you can watch an invisible area of the  
effective screen as well using the cdef switch.  
5600K : Set color temperature to 5600K  
RED : Adjusts the strength of the red color.  
BLUE : Adjusts the strength of the blue color.  
Note :  
R-GAIN/B-GAIN : Enables you to set the current  
color temperature manually.  
If the digital zoom factor is set to larger than 1x, the FENCE  
function will be deactivated.  
BRIGHTNESS : Select a brightness level in  
switching from setting in DAY mode to setting in  
NIGHT mode.  
The DIGITAL ZOOM function enlarges the pixel itself, which can  
cause deterioration of the quality.  
DETAIL  
[0~3]  
DIGITAL ZOOM  
[ON/OFF]  
Controls the horizontal or vertical distinction.  
You can set the digital zoom factor and position.  
If you press the SETUP switch with the DIGITAL  
ZOOM function set to ON, you will see the  
appropriate screen.  
V-SYNC  
[INT, LINE]  
Select the vertical sync mode for INT or LINE.  
If you select INT, the camera will use the internal  
synchronization.  
When the zoom factor and position are defined,  
the digital zoom function will operate.  
If selecting LINE, the camera will use the external  
power source frequency for the synchronization.  
You can adjust the LL-PHASE.  
22 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
Note :  
Use of DC 12V will fix V-SYNC to INT, which can not be  
changed.  
Note :  
If you set DIS to ON, the compensation area will be  
enlarged as set in the digital zoom factor.  
If you set the digital zoom factor to greater than the  
enlarged zoom factor for the compensation, the DIS  
function will be deactivated.  
AGC COLOR SUP  
[LOW , MID, HIGH]  
Adjust the color scheme according to the AGC  
value.  
INTELLIGENCE  
REVERSE  
[OFF, H, V, H/V]  
eINTELLIGENCEf  
Mirrors video signals horizontally, vertically, or  
both.  
MOTION  
OFF  
OFF  
2 3 4  
ADVANCED  
MASK AREA  
DISPLAY  
1
ON  
POSI/NEGA  
[+, -]  
SENSITIVITY  
RESOLUTION  
[4]  
[5]  
Output as it is or mirror the video brightness  
signal.  
PIP  
[OFF, ON]  
Displays a sub image together with the main  
image on the same screen using the Picture In  
Picture function.  
an  
You can set the motion detection and tracking in the  
INTELLIGENCE menu.  
Note :  
If more than one privacy zone is set and the PRIVACY  
SET is set to ON, the PIP function will be deactivated.  
MOTION  
[OFF,TRACKING,DETECTION]  
TRACKING  
Detects and tracks a moving object.  
If the INTELLIGENCE function is set to FENCE mode, the  
PIP menu will be deactivated.  
al  
DETECTION  
Detects a moving object.  
DIS  
[OFF, ON]  
Digital Image Stabilization will set the anti-shake  
compensation.  
al  
.
Note :  
If it is set to DETECTION, you can not set such functions as  
FIXED/MOVED and FENCE in the ADVANCED menu.  
English 23  
 
How to use OSD Menu  
ADVANCED  
[OFF, FIXED/MOVED, FENCE]  
- How to set the line  
LINEꢀ  
PIXEL LEVEL  
Detects a motion of an object and displays an  
image of any moving object before tracking the  
moving route.  
[4]  
<POINT>  
DIRECTION  
§¨  
FENCE  
This is to detect if a moving object passes  
through the specified LINE or AREA.  
In a condition where a moving object is detected  
in an analysis of the previous and current frames  
whose movement overlaps a certain area, the  
system displays “PASS” if the object’s center line  
passes through the line while it displays “ENTER”  
or “EXIT” if the center point passes through the  
area.  
If you press the SETUP switch with the LINE  
option set to ON, you can specify the position  
and detection direction of the line.  
If you change the PIXEL LEVEL for setting  
the position, specify the pixel that moves by a  
single pressure of the cdef switch.  
FENCEꢀ  
LINE  
AREA  
OFF  
OFF  
In <POINT>, you can specify the first position of  
the line by pressing the SETUP switch once, and  
the second position by pressing the switch again.  
Use the cdef switch to specify the  
position.  
Set each position of the two points and press the  
SETUP switch to complete the positioning.  
If you change the DIRECTION, you can specify  
the detection direction. The detection direction  
based on the defined two points will be  
displayed on the screen.  
You can set the position and detection direction of the  
LINE, and the size and position of the AREA.  
24 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
- How to set the area  
used simultaneously.  
In the boundary of the defined AREA and LINE, a FENCE  
detection error may occur if two or more moving objects  
overlap with each other or one object separates in  
multiple directions.  
AREAꢀ  
PIXEL LEVEL  
<SIZE>  
[4]  
<LOCATION>ꢅ  
FIXED/MOVED  
If an object on the screen suddenly disappears or  
an object comes out of nowhere and stays for a  
certain time, the area will be displayed.  
A detection (FIXED/MOVED) error may occur if :  
- multiple motions occur continuously in random  
directions  
- a fixed object moves in one position continuously  
- a second object screens the first moving object  
If you press the SETUP switch with the AREA  
option set to ON, you can specify the position  
and size of the area.  
E
on  
If you change the PIXEL LEVEL for setting  
the position, specify the pixel that moves by a  
single pressure of the cdef switch.  
a
MASK AREA [1~4]  
Specify a detection exception area to mask.  
In <SIZE>, press the SETUP switch and use  
the cdef switch to adjust the size.  
Press the SETUP switch again to complete the  
sizing.  
f
d
n.  
Select a mask number and specify the size and  
position.  
MASK AREAꢀ  
In <LOCATION>, press the SETUP switch and  
use the cdef switch to specify the position.  
Press the SETUP switch again to complete  
the positioning.  
<SIZE>  
e
<LOCATION>ꢅ  
fy  
n
Note :  
If you set the LINE of the FENCE to ON, PRIVACY 12 will  
not be available.  
Functions of FENCE, PIP, DIS and DIGITAL ZOOM (if the  
digital zoom factor is set to larger than 1x) can not be  
English 25  
 
How to use OSD Menu  
DISPLAY  
[ON, OFF]  
If you set the PRIVACY SET to ON, your PRIVACY  
ZONE settings will be applied.  
With the DISPLAY option set to ON, a motion or  
a set ADVANCED function will be displayed on  
the screen, if detected.  
You can change the style to adjust the mosaic size  
and color of the PRIVACY ZONE.  
ePRIVACY ZONEf  
SENSITIVITY  
[1~7]  
1
7
2
3
4
5
6
Set the sensitivity of the motion detection.  
8
9
10 11 12  
PRIVACY SET  
STYLE  
Y-LEVEL  
RED  
BLUE  
ON  
COLOR  
[128]  
[128]  
[128]  
RESOLUTION  
[1~5]  
If setting it to high, the camera can detect even a  
trivial movement of the target.  
Use the cdef switch to select one from  
PRIVACY 1 through 12.  
PRIVACY ZONE SETUP  
ePRIVACY ZONEf  
Select one from PRIVACY 1~12 and press the  
SETUP switch to confirm your setting. You can  
specify a pixel that moves as you change the PIXEL  
LEVEL to set the position.  
1
7
2
3
4
5
6
8
9
10 11 12  
PRIVACY SET  
STYLE  
ON  
MOSAIC1  
PRIVACY ZONE SET1ꢀ  
PIXEL LEVEL  
<POINT>ꢅ  
<POSITION>ꢅ  
[4]  
The PRIVACY function will protect your privacy by  
screening the privacy area that you have specified  
during monitoring. You can specify up to 12 privacy  
zones.  
26 – DIGITAL COLOR DOME CAMERA  
 
How to use OSD Menu  
- How to set the point  
OTHER SET  
You can set each position of the 4 points.  
eOTHER SETf  
If you press the SETUP switch in <POINT>,  
you will see the points available in the  
PRIVACY ZONE. Each time you press the  
SETUP switch, the points available will move.  
FACTORY DEFAULTS  
OSD COLOR  
BW  
Use the cdef switch to set the position  
of each point. Set each position of the four  
points and press the SETUP switch to  
complete the positioning.  
- How to set the position  
You can move the position of the overall area.  
FACTORY DEFAULTS  
All the settings will be restored to the factory  
default.  
By pressing the SETUP switch in  
<POSITION>, you can move the overall  
position of the privacy zone.  
OSD COLOR  
[BW, R/G/B]  
Use the cdef switch to move the  
position and press the SETUP switch to  
confirm it.  
You can set the OSD(On-screen Display) color to  
COLOR or B/W.  
L
Note :  
If more than one PRIVACY ZONE is specified and the  
PRIVACY SET is set to ON, the PIP function will be  
deactivated.  
If the 12th PRIVACY ZONE is specified, the LINE function  
of FENCE will be deactivated.  
English 27  
 
How to use OSD Menu  
S
Initial Configuration Table  
SYSTEM INFORMATION  
S
Camera Configuration  
eSYSTEM INFOf  
TYPE  
3_VAR_NOR_P  
CAMERA ID  
IRIS  
OFF  
ALC  
SERIAL NO. 000000000000000  
CAMERA VER.  
0.50_090101  
AGC  
VERY HIGH  
(F.FAST)  
MID  
MOTION  
DNR  
SHUTTER  
SENS-UP  
FLICKERLESS  
XDR  
OFF  
You can check the system information such as  
SERIAL NO and CAMERA VER.  
AUTO x4  
(OFF)  
MID  
LANGUAGE  
DAY/NIGHT  
DIGITAL ZOOM  
DETAIL  
AUTO  
OFF  
eLANGUAGEf  
ENGLISH  
FRANÇAIS  
DEUTSCH  
ESPAÑOL  
ITALIANO  
[2]  
AGC COLOR SUP  
REVERSE  
POSI/NEGA  
PIP  
MID  
H/V  
+
OFF  
DIS  
OFF  
The camera supports 5 different languages.  
Select a preferred language.  
V-SYNC  
INT  
28 – DIGITAL COLOR DOME CAMERA  
 
Specifications  
SPECIFICATIONS  
Items  
Camera Type  
Sub-items  
SCC-B5396N/SCC-B5398N  
CCTV Camera  
Device  
1/3” Super-HAD IT CCD  
811 x 508  
Image  
Total  
Pixels  
Effective  
768 x 494  
System  
Interlace  
Scanning Line  
Frame  
525 lines  
30frame/1sec  
Scanning  
Internal Mode  
15,734 Hz  
Horizontal  
Frequency  
Line-lock Mode  
Internal Mode  
Line-lock Mode  
Condition  
15,750 Hz  
59.94 Hz  
Vertical  
Frequency  
60 Hz  
Min. Scene illumination  
Sens-up  
OFF  
OFF  
F No.  
1.2  
1.2  
Level  
DAY  
0.4  
0.24  
NIGHT  
0.4  
0.24  
50  
30  
IRE  
IRE  
Lux  
Lux  
Lux  
Lux  
Min. Scene  
Illumination  
OFF  
1.2  
1.2  
1.2  
1.2  
15  
50  
30  
15  
IRE  
IRE  
IRE  
IRE  
0.12  
0.0008  
0.0005  
0.00023  
Lux  
Lux  
Lux  
Lux  
0.12  
0.0008  
0.0005  
0.00023  
Lux  
Lux  
Lux  
Lux  
512 times  
512 times  
512 times  
Number of Privacy Zone  
Day/Night  
12 (Polygonal Method)  
DAY/NIGHT/AUTO/EXT  
OFF/Tracking/Detection  
Off/On (Level Setting)  
x1 ~ x16 (x0.1 STEP)  
Off/On  
Motion Detection  
eXtended Dynamic Range(XDR)  
D-Zoom  
Functions  
PIP  
High Speed Shutter  
Flickerless  
1/60 ~ 1/10Ksec (OSD/External Control)  
Off/On  
x2 ~ x512  
Sens-Up  
BLC  
Off/On (Area Setting)  
English 29  
 
Specifications  
Items  
Sub-items  
SCC-B5396N/SCC-B5398N  
Off/On (Max.Level Setting)  
Off/On (Phase Control)  
Off/On (Max.54ea/2Line)  
ATW1/ATW2/AWC/3200K/5600K  
Off/On (Adaptive 3D+2D)  
Off/On  
AGC  
Line Lock  
Camera ID  
White Balance  
Digital Noise Reduction(DNR)  
Digital Image Stabilization(DIS)  
Intelligent Video  
Etc. Function  
Horizontal  
Fixed/Moved, Fence  
Detail, Reverse(H/V), Posi/Nega  
600 TV Lines  
Resolution  
Vertical  
350 TV Lines  
Video Output  
S/N Ratio  
-
VBS 1.0Vp-p, 75 Ω  
Approx. 52dB  
S/N Ratio  
Auto Iris (DC)  
Lens  
Lens Drive Type  
SCC-B5396 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2  
SCC-B5398 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2  
0 ~ 355°(100° in CW(Clockwise) direction,  
255° in CCW (Counterclockwise) direction)  
PAN  
TILT  
Range  
Range  
0 ~ 90°  
Remote  
Control  
Coaxitron (Data On Coax cable)  
Yes (with SCX-RD100)  
Operating Temperature  
Humidity  
-10˚C ~ +50˚C  
Less than 90%  
Environmental  
Conditions  
AC24V 10%(60Hz 0.3Hz)  
DC12V 10%  
Power Requirement  
Power Consumption  
Power  
2.3W  
Dimensions  
(Ø x H)  
150(Ø) x 121(H)mm  
Physical  
Specification  
Weight  
Color  
980 g  
white  
30 – DIGITAL COLOR DOME CAMERA  
 
Specifications  
Items  
Sub-items  
SCC-B5398P/SCC-B5396P  
Camera Type  
CCTV Camera  
Device  
1/3” Super-HAD IT CCD  
795 x 596  
Image  
Total  
Pixels  
Effective  
752 x 582  
System  
Scanning Line  
Frame  
Interlace  
625 lines  
25frame/1sec  
Scanning  
Internal Mode  
15,625 Hz  
Horizontal  
Frequency  
Line-lock Mode  
Internal Mode  
Line-lock Mode  
Condition  
15,625 Hz  
50 Hz  
Vertical  
Frequency  
50 Hz  
Min. Scene illumination  
Sens-up  
OFF  
OFF  
F No.  
1.2  
1.2  
Level  
DAY  
0.4  
0.24  
NIGHT  
0.4  
0.24  
50  
30  
IRE  
IRE  
Lux  
Lux  
Lux  
Lux  
Min. Scene  
Illumination  
OFF  
1.2  
1.2  
1.2  
1.2  
15  
50  
30  
15  
IRE  
IRE  
IRE  
IRE  
0.12  
0.0008  
0.0005  
0.00023  
Lux  
Lux  
Lux  
Lux  
0.12  
0.0008  
0.0005  
0.00023  
Lux  
Lux  
Lux  
Lux  
512 times  
512 times  
512 times  
Number of Privacy Zone  
Day/Night  
12 (Polygonal Method)  
DAY/NIGHT/AUTO/EXT  
OFF/Tracking/Detection  
Off/On (Level Setting)  
Max. x16  
Motion Detection  
eXtended Dynamic Range(XDR)  
D-Zoom  
Functions  
PIP  
Off/On  
High Speed Shutter  
Flickerless  
1/50 ~ 1/10Ksec (OSD/External Control)  
Off/On  
x2 ~ x512  
Sens-Up  
BLC  
Off/On (Area Setting)  
English 31  
 
Specifications  
Items  
Sub-items  
SCC-B5398P/SCC-B5396P  
Off/On (Max.Level Setting)  
Off/On (Phase Control)  
Off/On (Max.54ea/2Line)  
ATW1/ATW2/AWC/3200K/5600K  
Off/On (Adaptive 3D+2D)  
Off/On  
AGC  
Line Lock  
Camera ID  
White Balance  
Digital Noise Reduction(DNR)  
Digital Image Stabilization(DIS)  
Intelligent Video  
Etc. Function  
Horizontal  
Fixed/Moved, Fence  
Detail, Reverse(H/V), Posi/Nega  
600 TV Lines  
Resolution  
Vertical  
350 TV Lines  
Video Output  
S/N Ratio  
-
VBS 1.0Vp-p, 75 Ω  
Approx. 52dB  
S/N Ratio  
Auto Iris (DC)  
Lens  
Lens Drive Type  
SCC-B5396 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2  
SCC-B5398 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2  
0 ~ 355°(100° in CW(Clockwise) direction,  
255° in CCW (Counterclockwise) direction)  
PAN  
TILT  
Range  
Range  
0 ~ 90°  
Remote  
Control  
Coaxitron (Data On Coax cable)  
Yes (with SCX-RD100)  
Operating Temperature  
Humidity  
-10˚C ~ +50˚C  
Less than 90%  
Environmental  
Conditions  
AC24V 10%(50Hz 0.3Hz)  
DC12V 10%  
Power Requirement  
Power Consumption  
Power  
2.3W  
Dimensions  
(Ø x H)  
150(Ø) x 121(H)mm  
Physical  
Specification  
Weight  
Color  
980g  
white  
32 – DIGITAL COLOR DOME CAMERA  
 
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking on the product, accessories or literature indicates that the product and its electronic accessories  
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their  
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,  
please separate these items from other types of waste and recycle them responsibly to promote the sustainable  
reuse of material resources.  
Household users should contact either the retailer where they purchased this product, or their local government  
office, for details of where and how they can take these items for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract.  
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.  
 

Radio Shack Thermometer 63 1089 User Guide
RBH Sound Home Theater System CT 5 User Guide
RCA MP3 Player TH20 User Guide
Resolution Audio Stereo Amplifier Opus 21 User Guide
Roberts Gorden Gas Heater NEMA 4 User Guide
Roland Switch MSQ 100 User Guide
Ryobi Trimmer P2601 User Guide
Samsung DVD Player DVD V642K User Guide
Samsung Telephone MM A940 User Guide
Sanus Systems Surge Protector ELM205 User Guide