SCdefault
9In-5stallation instructions
·
MONTERINGSANVISNING INSTALLATION INSTRUCTIONS
·
MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-5 B205, B235
Parking heater
Accessories Part No.
Group
9:87-31
Date
Instruction Part No.
Replaces
32 025 650
32 026 240
Oct 07
53 29 271
53 29 271 Sep 05
5
6
8
2
1
4
12
7
9
11
3
10
E930A393
1 Extension cable
2 Connector plug and connector cable
3 Holder
4 Screw (x2) -M05
5 Screw
6 Star washer
7 Heating element
8 Locking clip
9 Cable tie (x5)
10 Clips
11 Screw (x2) M06-
12 Nut (x2) M06-
Saab 9-5 B205, B235
5329271 3
5
5
6
E930A261
5 -M05: Mark out the location for the holder for the
supply connector plug. The arrow on the holder
should point forwards. Make holes with a brad-
awl.
6 -M05: Place the supply connector plug in the
holder so that the cover opens upwards. Fit the
holder to the bumper.
Proceed to step 12.
Saab 9-5 B205, B235
4 5329271
7
9
9
10
E930A395
7 M06-: Tape the spoiler using woven tape for
example to prevent damage to the paintwork.
8 M06-: Mark out the location for the holder for the
supply connector plug using a bradawl on the
rib, see illustration. The arrow on the holder
should point forwards.
9 M06-: Drill two 6 mm holes in the rib. Bend the
rib down using a hammer handle for example in
order to facilitate access. Fit a plastic hose to the
drill to prevent damage to the paintwork.
10 M06-: Position the supply connector plug in the
holder and secure it with screw and nut. The
cover must open towards the number plate.
11 M06-: Remove the tape.
Saab 9-5 B205, B235
5329271 5
13
14
E930A394
12 Raise the car and close the drain plug.
13 Insert the supply connector cable between the
radiator and the subframe. Locate the cable
connection on top of the gearbox.
14 Drill a 3.5 mm diameter hole for the ground
cable in the underside of the left-hand structural
member.
15 Scrape off any paint to ensure a good ground
connection and secure the ground cable with a
screw and lock washer (place the lock washer
between the ground cable terminal and the
body). Apply light anti-corrosion agent, part no.
30 15 971. Secure the ground cable along the
supply cable.
16 Fit the air shield and lower the car.
Saab 9-5 B205, B235
6 5329271
17
17
17
17
E930A396
17
17
17 Remove the engine cover and disconnect any
hoses and electrical connections from the turbo-
charger delivery pipe. Remove the turbocharger
delivery pipe between the charge air cooler and
the throttle body, including the bypass pipe and
the heat shield over the exhaust manifold.
Plug the holes.
Saab 9-5 B205, B235
5329271 7
20
18
23
E930A397
18 If necessary, disconnect the cable to the lower
oxygen sensor and remove the frost plug using
tool 260 147 020. Use, for example, a 17 mm
socket.
24 Aut: Secure the supply connector cable to the
lower cable by the battery tray with the clips
included in the kit.
Man: Secure the supply connector cable to the
19 Apply acid-free petroleum jelly, part no. 30 06
665, or equivalent, to the heating element O-
ring.
left-hand structural member with a strap.
WARNING
20 Fit the heating element so that the electrical
connection is directed towards the left-hand side
of the car and the connection is between the
coolant pipes and under the turbocharger cool-
ant pipe. Do not tighten the nut holding the heat-
ing element.
Make sure that the cable does not make contact
with sharp edges or hot surfaces. Be aware of the
turbo unit. Scrapes and heat damage can cause a
short-circuit.
21 Adjust the position of the heating element so
that it is free from contact with the coolant pipes.
Tighten the nut.
Tightening torque 3.5 Nm (2.5 lbf ft)
Connect and secure the cable to the lower oxy-
gen sensor.
22 Apply acid-free petroleum jelly, part no. 30 15
286 or equivalent, to the O-ring on the supply
connector cable and connect the cable to the
heating element.
23 Fit the lock clip over the connection. A click
should be heard when the lock clip is fitted cor-
rectly.
Saab 9-5 B205, B235
8 5329271
25 Check the ground connection between the
ground pin on the connector plug, the heater
casing and the car body.
26 Fit the heat shield, lubricate the bypass pipe O-
ring with acid-free petroleum jelly and fit the tur-
bocharger delivery pipe, including the bypass
pipe. Connect the vacuum hose to the bypass
pipe and the hoses and connector to the turbo-
charger delivery pipe. Fit the engine cover.
27 Fill up with coolant and check the system for
leaks.
28 Bleed the cooling system in the following way:
Note
The A/C or ACC should be turned OFF.
Fill the coolant system to the MAX level. Close
the expansion tank cap. Start the engine and run
to operating temperature at varying engine
speeds until the radiator fan cuts in. Carefully
open the expansion tank cap and top up to the
MAX level. Close the cap. Switch off the engine
and if necessary top the coolant up to the MAX
level.
29 Check that the cooling system does not leak and
that the heater works.
30 Place the installation instructions in the car and
draw the customer's attention to the user
instructions.
Saab 9-5 B205, B235
5329271 9
B
A
E930A073
A Branch cable set
B Timer kit
Saab 9-5 B205, B235
10 5329271
User instructions
• The extension cable must be made of oil-resist-
ant rubber and approved for outdoor use with a
2
cross-sectional area of at least 3x1.5 mm .
• The engine heater must be connected to a
grounded outlet only.
• Handle all cables with care. Pay particular atten-
tion to the risk of pinching between the bonnet
and the body of the car and the risk of cuts on
sharp metal components.
WARNING
Check regularly the ground connection between
the ground pin in the connector plug, the heater
casing and the car body.
• Inspect regularly the extension cable for damage
or ageing. Damaged cables must be renewed
immediately.
Note
The function of the heater will be at risk if:
• there are impurities in the coolant
• the coolant level is too low or if there is air in the
system
• there is ice slush in the system
• radiator sealant is used
Saab 9-5 B205, B235
|