SECO LARM USA Security Camera EV 122C FVB3Q User Guide

Flush-Mount Low-Profile  
UFO Camera  
Manual  
Model  
Video Output  
NTSC  
Resolution  
EV-122C-FVB3Q  
EV-6640-N3WQ  
EV-122C-PVB3Q  
EV-6640-P3WQ  
480 TV Lines  
600 TV Lines  
480 TV Lines  
600 TV Lines  
NTSC  
PAL  
PAL  
Small size - only 3” diameter  
/3” Sony Super HAD II CCD  
3.7mm Pinhole lens  
Low 0.05 Lux rating  
Lens rotates to nearly any angle  
1
Low-profile design blends into nearly  
any décor  
Vandal-resistant metal housing  
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.  
 
ENFORCER Flush-Mount Low-Profile UFO Camera  
Overview:  
Screw  
(1 Shown, 3 included)  
Base  
Ring bracket  
(inside the ceiling wa l)  
Camera ball  
Flange  
Female BNC  
connector  
DC Jack  
DC Plug with  
terminal block  
Flange  
Base  
Ring bracket  
Before Starting:  
1. Please read this manual carefully and keep it for  
future reference.  
4. Do not point the camera at the sun. Heat could damage  
the camera, even when not in use.  
2. Use the camera within given temperature and  
5. Do not mount the camera in areas exposed to  
radiation, strong magnetic fields, or strong  
electrical signals.  
electrical limits.  
3. Do not mount the camera where it is exposed to rain or  
other moisture, or in humid or dusty places.  
6. Do not drop the camera or subject it to strong vibrations  
Installation:  
1. Run a 12VDC power supply wire and a video cable with 8. Place the ring bracket behind the hole.  
a male BNC connector to the wall or ceiling where the  
Note: Ring bracket is not necessary if mounting  
camera is to be mounted.  
directly to wall.  
2. Temporarily connect the camera to the 12VDC  
power supply.  
9. Push the base into the hole, and secure to the ring  
bracket using the three supplied marking screws.  
10. Run the power supply and video cable through the  
wall or ceiling to the hole, and through the bracket  
and base. Connect to the camera’s power and video  
connectors.  
3. Temporarily connect the camera’s female BNC  
connector to the video cable’s male BNC connector.  
4. While watching the monitor, hold the camera against the  
wall or ceiling by hand where it is to be mounted, then  
turn the camera until it is certain that this mounting  
location is correct. Use a pencil to mark the location.  
5. Disconnect the 12VDC power supply and video cable.  
6. Drill a 21/4” (56m) hole in the ceiling or wall where the  
camera is to be mounted.  
11. Hold the ball in the base, and secure with the flange.  
Do not tighten securely.  
12. Apply the power to the camera. Watch the monitor  
and adjust the angle of the lens.  
13. Secure the camera by tightening the flange.  
7. Twist the flange off the base and remove the  
camera ball.  
14. Do a final test of the video camera and monitor.  
SECO-LARM U.S.A., Inc.  
3
 
ENFORCER Flush-Mount Low-Profile UFO Camera  
Troubleshooting:  
Check that the camera is powered up.  
Check that the power supply’s polarity is correct.  
Check that the monitor is powered up.  
Check that the video cable connecting the camera to the  
monitor is connected properly.  
The screen is blank.  
Clean the lens using a soft, clean cloth.  
Check that the light source is adequate.  
The screen image is dim  
Adjust the monitor’s contrast knob.  
Change the position of the camera.  
The screen image has poor contrast.  
Change the position of the camera.  
Change the position of the camera.  
Check that the correct power supply is in use.  
The screen image flickers.  
The screen image is distorted.  
The camera case is hot.  
IMPORTANT  
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and  
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this  
product in violation of any current laws or statutes.  
WARNING  
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open  
the case of this device, as there are no field-serviceable components inside.  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to  
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to  
correct the interference at his or her own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a  
period of three (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of  
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or  
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is  
not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or  
property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is  
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without  
notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,  
without the written permission of SECO-LARM.  
SECO-LARM U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
Tel: 800-662-0800 / 949-261-2999  
PICSN4  
M UFO_Camera_1206.docx  
4
SECO-LARM U.S.A., Inc.  
 

QSC Audio Stereo System 922uz User Guide
Quantum Computer Drive LTO 2 User Guide
Radio Shack Cordless Telephone 43 3815 43 3898 User Guide
RCA Flat Panel Television ES J100256 User Guide
Ricoh Printer MP 2000L User Guide
Sansui Flat Panel Television HDLCD4060 User Guide
Sanyo Cell Phone RL 4920 User Guide
Sanyo Projector PDG DHT100H User Guide
Scag Power Equipment Lawn Mower STT 29DFI User Guide
Senario Video Games 20894 User Guide