SATA II / ATA 133 PCIe Card RC216
User Manual
SATA II/ATA 133 PCIe Card RC216
User Manual
z
1x Manual
z
z
z
1x Driver CD
1x SATA Data Cable
1x ATA 133 IDE Cable
Note: Contents may vary depending on country/market.
3
SATA II/ATA 133 PCIe Card RC216
User Manual
Hardware Description
G (Jumper Settings)
JP
Description
Active Port
J1-J4
1-2 close
2-3 close
1-2 close
2-3 close
Enable SATA Port CON1
Enable SATA Port CON3
Enable SATA Port CON2
Enable SATA Port CON4
J5-J8
Note: There are four SATA ports in PCIe SATA II 300 + PATA Raid Card.
We name these ports CON1 to CON4. Ports CON3 & CON4 are
internal SATA ports and CON1 & CON2 are external SATA ports. By
4
SATA II/ATA 133 PCIe Card RC216
User Manual
changing the jumper setting on the PCIe SATA II 300 + PATA Raid Card
that allows you to select between external and internal ports to use. By
default, Port CON1 & CON2 are working.
Hardware Installation
1.
2.
3.
4.
Turn Off the power to your computer.
Unplug the power cord and remove your computer’s cover.
Remove the slot bracket from an available PCIe slot.
To install the bard, carefully align the card’s bus connector with the
selected PCIe slot on the motherboard. Push the board down
firmly.
5.
Attach your internal or external devices to the PCIe SATA II 300 +
PATA Raid Card.
6.
7.
Replace the slot bracket’s holding screw to secure the card.
Replace the computer cover and reconnect the power cord.
RAID Arrays
RAID Arrays are setup in the PCIe SATA II 300 + PATA Raid Card’s BIOS.
There are four configurations supported:
RAID level/Type
RAID 0
Configurations
Disk Striping
Disk Mirroring
Number of disks needed
2 or 3 or 4
2
RAID 1
5
SATA II/ATA 133 PCIe Card RC216
User Manual
RAID 0+1
Disk Striping
Mirroring
Disk Concatenation
4
+
JBOD
2 or 3 or 4
RAID 0 (Striping)
1.
As the BIOS boots press Ctrl+J when prompted to enter the RAID
BIOS.
2.
3.
4.
At the next screen select Create RAID Disk Drive, press Enter.
Enter RAID name, press Enter.
Please use arrow keys ↑ and ↓to switch the RAID level to
0-Stripe, then press Enter.
5.
6.
Please use arrow keys ↑ and ↓to switch the disk, use the “space”
key to mark the selected disk, then press Enter.
Please use arrow keys ↑ and ↓ to select chunk size from 4K, 8K,
16K, 32K, 64K or 128K, then press Enter.
7.
8.
Input the RAID size, press Enter.
When asked Created RAID on the select HDD (Y/N)?, press Y to
accept.
9.
At the next screen select Save And Exit Setup, press Enter. When
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.
RAID 1 (Mirroring)
1. As the BIOS boots press Ctrl+J when prompted to enter the RAID
6
SATA II/ATA 133 PCIe Card RC216
User Manual
BIOS.
2.
3.
4.
At the next screen select Create RAID Disk Drive, press Enter.
Enter RAID name, press Enter.
Please use arrow keys ↑ and ↓to switch the RAID level to
1-Mirror, then press Enter.
5.
Please use arrow keys ↑ and ↓to switch the disk, use the “space”
key to mark the selected disk, then press Enter.
Input the RAID size, press Enter.
6.
7.
When asked Created RAID on the select HDD (Y/N)?, press Y to
accept.
8.
At the next screen select Save And Exit Setup, press Enter. When
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.
CONCATENATION (JBOD)
1.
As the BIOS boots press Ctrl+J when prompted to enter the RAID
BIOS.
2.
3.
4.
At the next screen select Create RAID Disk Drive, press Enter.
Enter RAID name, press Enter.
Please use arrow keys ↑ and ↓to switch the RAID level to
JBOD-Concatenate, then press Enter.
5.
6.
Please use arrow keys ↑ and ↓to switch the disk, use the “space”
key to mark the selected disk, then press Enter.
Input the RAID size, press Enter.
7
SATA II/ATA 133 PCIe Card RC216
User Manual
7.
8.
When asked Created RAID on the select HDD (Y/N)?, press Y to
accept.
At the next screen select Save And Exit Setup, press Enter. When
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.
RAID 0+1 (Striping + Mirroring)
1.
As the BIOS boots press Ctrl+J when prompted to enter the RAID
BIOS.
2.
3.
4.
At the next screen select Create RAID Disk Drive, press Enter.
Enter RAID name, press Enter.
Please use arrow keys ↑ and ↓to switch the RAID level to
01-Stripe+Mirror, then press Enter.
5.
Please use arrow keys ↑ and ↓ to select chunk size from 4K, 8K,
16K, 32K, 64K or 128K, then press Enter.
6.
7.
Input the RAID size, press Enter.
When asked Created RAID on the select HDD (Y/N)?, press Y to
accept.
8.
At the next screen select Save And Exit Setup, press Enter. When
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.
Delete RAID Disk Drive
1.
As the BIOS boots press Ctrl+J when prompted to enter the RAID
BIOS.
8
SATA II/ATA 133 PCIe Card RC216
User Manual
2.
3.
At the next screen select Delete RAID Disk Drive, press Enter.
Please use arrow keys ↑ and ↓to select the array you want to
delete, use the “space” key to mark the selected array, then press
DEL.
4.
When asked ALL DATA ON THE RAID WILL LOST!! ARE YOU
SURE TO DELETE (Y/N), press Y to accept.
Solve Mirror Conflict
When a RAID set is created, then metadata written to the disk includes
drive connection information. If, after a disk failure, the replacement disk
was previously part of a RAID set (or used in another system), it may
have conflicting metadata. If so, this will prohibit the RAID set from being
either created or rebuilt, in order for the RAID set to function properly,
this old metadata must be first overwritten with the new metadata. To
resolve this, from the main BIOS window select Solve Mirror Conflict,
then press Enter, the correct metadata, including the correct drive
connection information, will be written to the replacement disk.
Rebuild Mirror Drive
When a failure to one member occurs, you will be notified by the RAID
BIOS during boot. The steps below will guide you in rebuilding a failed
mirror set.
1.
Replace he failed drive(s) with one of equal or greater capacity, then
9
SATA II/ATA 133 PCIe Card RC216
User Manual
start the computer.
2.
During boot press Ctrl+J to enter the RAID BIOS.
3.
4.
Select Rebuild Mirror Drive press Enter.
Please use arrow keys ↑ and ↓to select the array you want to
rebuild, press Enter.
5.
6.
Please use arrow keys ↑ and ↓to select the destination disk,
press Enter.
When rebuilding is finished, select Save And Exit Setup, press
Enter. When asked Save to disk &Exit (Y/N)?, press Y to exit the
BIOS.
BIOS Configuration
The PCIe SATA II 300 + PATA Raid Card BIOS will appear every time your
system starts up. During this (POST) process, the BIOS will show up and
indicate the devices attached to it.
Driver Installation
For Windows® 2000, XP and Server 2003
For New Installation
A new installation requires a floppy disk for the driver installation. To
make this floppy disk, copy the contents of the “RC-216\Floppy32”
folder, found on the driver CD, onto a blank floppy disk then follow the
10
SATA II/ATA 133 PCIe Card RC216
User Manual
directions below.
1.
2.
3.
4.
5.
6.
7.
Setup the RAID Array prior to Windows installation.
Follow Microsoft’s Windows installation procedure.
Restart the computer when prompted by Windows’ installation.
At the Windows Setup screen, press F6 to install the RAID driver.
When prompted, press S to specify the location of the driver.
Insert the floppy disk, then press Enter.
Select (Windows 2000) RAID Driver for JMicron JMB363
Controller or (Windows XP/2003) RAID/AHCI Driver for JMicron
JMB36X Controller, then press Enter.
8.
Press Enter to finish driver installation, then follow the on-screen
instructions to complete the Windows installation.
For An Existing Installation
1.
Setup the RAID Array prior to driver installation and boot up to
Windows.
2.
3.
At the Found New Hardware Wizard window pop-up, please click
Cancel button to cancel the driver installation for the device at this
moment. The driver for this device will be installed in the next step.
Please insert the CD driver bound with PCIe SATA II 300 + PATA
Raid Card into your CD-ROM Drive.
4.
5.
At the Windows desktop, click Start, then Run.
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your
11
SATA II/ATA 133 PCIe Card RC216
User Manual
CD-ROM drive letter)
6.
7.
Follow the on-screen instructions to complete the installation.
Restart Windows to complete the installation.
For Windows® XP-x64/Server 2003-x64
For New Installation
A new installation requires a floppy disk for the driver installation. To
make this floppy disk, copy the contents of the “RC-216\Floppy64”
folder, found on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. Restart the computer when prompted by Windows’ installation.
4. At the Windows Setup screen, press F6 to install the driver.
5. When prompted, press S to specify the location of the driver.
6. Insert the floppy disk, then press Enter.
7. Select (Windows XP/2003 x64) RAID/AHCI Driver for JMicron
JMB36X Controller, then press Enter.
8. Press Enter to finish driver installation, then follow the on-screen
instructions to complete the Windows installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
12
SATA II/ATA 133 PCIe Card RC216
User Manual
Windows.
2. At the Found New Hardware Wizard window pop-up, please click
Cancel button to cancel the driver installation for the device at this
moment. The driver for this device will be installed in the next step.
3.
Please insert the CD driver bound with PCIe SATA II 300 + PATA
Raid Card into your CD-ROM Drive.
4.
5.
At the Windows desktop, click Start, then Run.
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your
CD-ROM drive letter)
6.
7.
Follow the on-screen instructions to complete the installation.
Restart Windows to complete the installation.
For Windows® Vista
For New Installation
A new installation requires a floppy disk for the driver installation. To
make this floppy disk, copy the contents of the “RC-216\Floppy32”
folder, found on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. Restart the computer when prompted by Windows’ installation.
4. At the Windows Setup screen, press Load Driver to install the
driver.
13
SATA II/ATA 133 PCIe Card RC216
User Manual
5. Insert the floppy disk, please select JMicron JMB36X Controller
(A:\jraid_f.inf), then press Next. (Change A:\ to match your floppy
drive letter)
6. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At the Found New Hardware Wizard window pop-up, please click
Cancel button to cancel the driver installation for the device at this
moment. The driver for this device will be installed in the next step.
3.
Please insert the CD driver bound with PCIe SATA II 300 + PATA
Raid Card into your CD-ROM Drive.
4.
5.
At the Windows desktop, click Start, then Run.
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your
CD-ROM drive letter)
6.
7.
Follow the on-screen instructions to complete the installation.
Restart Windows to complete the installation.
For Windows® Vista-x64
For New Installation
A new installation requires a floppy disk for the driver installation. To
14
SATA II/ATA 133 PCIe Card RC216
User Manual
make this floppy disk, copy the contents of the “RC-216\Floppy32”
folder, found on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. Restart the computer when prompted by Windows’ installation.
4. At the Windows Setup screen, press Load Driver to install the
RAID driver.
5. Insert the floppy disk, please select JMicron JMB36X Controller
(A:\jraid_f.inf), then press Next. (Change A:\ to match your floppy
drive letter)
6. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At the Found New Hardware Wizard window pop-up, please click
Cancel button to cancel the driver installation for the device at this
moment. The driver for this device will be installed in the next step.
3.
Please insert the CD driver bound with PCIe SATA II 300 + PATA
Raid Card into your CD-ROM Drive.
4.
At the Windows desktop, click Start, then Run.
15
SATA II/ATA 133 PCIe Card RC216
User Manual
5.
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your
CD-ROM drive letter)
6.
7.
Follow the on-screen instructions to complete the installation.
Restart Windows to complete the installation.
To Verify Driver Installation
Click on the “Device Manager” tab in System Properties, which you
access from the Windows Control Panel. You should see an “JMicron
JMB36X Controller” installed under “SCSI and RAID controllers”
item.
Thank you for purchasing a quality Rosewill Product.
support for your product.
16
|