Notes
Table of Contents
Quick Reference .................................................................. 3
Powering on the system
Watching a DVD
Listening Over Vehicle Speakers
Using Other Video Sources
Watching TV
About the ClearVue 6821 DVD System...............................4
Operating the System.......................................................... 5
Precautions .................................................................... 5
Switching On .................................................................. 5
Lowering the Screen ....................................................... 5
What You Can Play ........................................................ 6
Front Panel Controls ....................................................... 6
Using the Headphones.................................................... 7
Using the Car Speakers .................................................. 8
Using the TV Tuner ......................................................... 9
Remote Control Reference ............................................... 10
Remote Control Battery Replacement ........................... 11
Basic Remote Functions .............................................. 11
Basic Functions ................................................................. 12
Changing View Settings ................................................ 15
Advanced Functions .......................................................... 16
Customize Settings ...................................................... 16
DVD Menus .................................................................. 19
Viewing Options............................................................ 20
Language Support Options ........................................... 21
Using Auxiliary Sources .................................................... 22
Important Safety Notices................................................... 24
ClearVue 6821 DVD System Owner’s Manual
Page 2
Important Safety Notices
Quick Reference
To power on the system:
DANGER AN IMPROPERLY LOCATED OR INSTALLED
MONITOR CAN CAUSE DEATH OR SERIOUS BODILY
INJURY
1 Turn ignition switch to Run or ACC.
2 Press the release button as shown.
3 Screen will power on automatically.
To watch a DVD:
READ THE FOLLOWING INFORMATION
THOROUGHLY BEFORE INSTALLATION
1 Power on the system.
It is unlawful in most jurisdictions for a person to
operate a motor vehicle equipped with a television
monitor located where the operator can directly or
indirectly view it. In some jurisdictions, television
monitors in motor vehicles may be prohibited or may
require the television monitor to be located behind the
operators seat.
2 Point the remote at the screen and press the POWER
button to turn on the DVD player.
3 Press the Eject button on DVD player or remote to open
tray.
4 Insert a disc into the DVD and press Eject button to close
tray. Playback begins.
Ensure that you are completely aware of and familiar
with all applicable regulations and restrictions related
to the use of this equipment in a motor vehicle for
your local jurisdiction.
To listen over the vehicle speakers:
1 Turn on the vehicle radio and tune it to 88.7 FM.
2 Press SPEAKER ON/OFF on the remote until “FM ON”
appears on the screen.
In the event of an accident, passengers can be thrown
against objects in the vehicle. Ensure that the monitor
location is in a position where it will not be struck by a
passenger in the event of an accident.
3 If you hear no audio, try tuning the radio to 89.1 FM.
To use another video source:
1 Connect the RCA audio and video outputs of the device to
the Audio and Video RCAInputs on the front of the DVD
player.
ALWAYS mount the monitor securely using appropriate
hardware to a structural component in the vehicle. Failure
to properly secure a monitor could result in the
monitor coming loose and endangering the
passengers in the event of an accident.
2 Press MODE on the remote until the video image appears
on the screen.
To watch broadcast television:
1 Press POWER on the remote.
The INSTALLER accepts all responsibility for proper
installation of the monitor. Rosen Products, LLC, is not
liable for any damages, incidental or otherwise, which
may result from the installation of this product.
2 Press MODE until ”TV Mode” appears on the screen.
3 Press the up and down arrow buttons on the remote to
change channels.
Page 3
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 24
Frequently Asked Questions
About the ClearVue 6821 DVD System
Frequently Asked Questions
About the ClearVue 6821 DVD System
Why don’t I hear ClearVue sound over my radio?
Welcome to the ClearVue 6821 DVD System Owner’s Manual.
The ClearVue 6821 DVD system includes the following
components:
Try both 89.1 FM and 88.7 FM on your radio dial, and make sure
that the FM Modulator is on by pressing and releasing the
“SPEAKER ON/OFF” button on the remote until “FM ON” is
displayed on the screen.
• Overhead Monitor
• DVD Player with TV Tuner
• Wireless IR Headphones (2 pair)
• Wireless IR Transmitter Dome
• Remote Control
Why doesn’t the TV button on the remote turn on the
TV Tuner?
Some buttons on your ClearVue remote are for other Rosen
systems and products. Use the MODE button to turn the TV
Tuner on with your system.
How do I change channels on the TV Tuner?
Press the up and down arrow buttons on the remote.
Why did the headphones stop working?
• FM Modulator (enables the DVD sound to be
heard over your vehicle’s speakers).
• Vehicle Trim Ring
Check the power switch and the volume control. Check the
MUTE button on the remote. Then try adding new batteries.
• Other parts and cables which are installed out of sight
in your vehicle.
Why did the remote stop working?
Note: The system is intended to be used with your ignition
key switch in the Run or Acc position. Extended use
of the system without the engine running should be
avoided, as it could drain the battery.
Direct remote towards the black oval above the monitor when
pressing buttons. Then try adding new batteries.
Why do I have poor ClearVue sound quality sometimes
over the speakers?
You may be in an area that has a strong radio signal at the same
FM frequency as the FM Modulator. See your Rosen dealer to
have the ClearVue FM frequency reset.
Why do I have a poor Video on my screen?
Your DVD players setup may be set to PAL. Check to verify that
your “TV Type” in the setup menu is set to NTSC.
Page 23
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 4
Operating the System
Using Auxiliary Sources
Operating the System
Using Auxiliary Sources
The system includes RCA inputs on the front of the DVD player
that enable you to attach an external source device such as a
video game or camcorder. You can also listen to an external
audio source such as an MP3 player, portable CD player, or
MiniDiscTM.
Precautions
• Use this system only after proper installation by a qualified
installer.
• If the internal temperature of the vehicle is extremely high,
allow a short cooling down period before operating the unit.
Note: Before attempting to use any auxiliary source, be sure you
have the appropriate cable to connect to the system.
• If the unit shows signs of overheating or malfunction, power
off the unit and consult your dealer immediately.
To connect the auxiliary device to the DVD front panel RCAjacks:
1 Connect the right channel audio to the red jack.
2 Connect the left channel audio to the white jack.
3 Connect the video to the yellow jack.
• Do not open the unit; there are no serviceable parts inside.
Switching On
Use the system when your vehicle is running or the ignition
switch is in the “accessory” position.
Note: When using a non-battery operated Auxiliary source
(video game, or other) in a vehicle, a 12VDC/110VAC
power inverter is required.
To avoid a dead battery, do not use the system for long
periods of time without the engine running.
To play an auxiliary device:
1 Power on system.
Lowering the Screen
To lower the screen, press the release button on the overhead
monitor, as shown. The screen will lower into the viewing
position.
2 Power on the device.
3 Press MODE on the remote until the auxiliary source device is
activated. The system cycles from DVD Mode, to TV Mode, to
auxiliary source mode, and back to DVD Mode.
To adjust the viewing position, insert two fingers into the
adjustment knob and rotate as needed.
Adjustment Knob
Release Button
Page 5
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 22
Advanced Functions
Operating the System
What You Can Play
Language Support Options
This unit is designed for use with DVD, VCD, CD, CD-R, and CD-
RW with MP3 or MPEG-1 file recordings. Functions will vary
depending on the features available on the disc you are playing.
Some DVDs offer a variety of language options for DVD audio,
DVD menu text, and DVD subtitles. Features vary depending on
the DVD you are viewing.
Note: LDs are not compatible.
If DVDs and VCDs contain multiple audio tracks, the same video
can be viewed with different audio.
Front Panel Controls
To change the audio on a DVD:
Backlighting on the front panel controls indicates when power is on.
1 During DVD playback, press the AUDIO button on the remote
control.
2 3 4
5
6
1
“AUDIO x/y” appears in the monitor, where x represents the
current audio stream and y represents the total available
audio streams.
VIDEO
2 Press the AUDIO button to cycle through all available audio
streams until the preferred audio is selected.
To change the audio on a VCD:
M
• During VCD playback, press the AUDIO button until the
desired audio is selected.
7
8 9 10 11 12 13 14
1
2
3
4
5
6
7
8
9
Arrow buttons—Highlight selections.
Next track—Selects next chapter, title, or CD track.
Previous track—Selects previous chapter, title, or track.
DVD tray.
Power—Powers the system on and off.
Eject—Ejects a disc.
Aux input—Right channel audio input, red.
Aux input—Left channel audio input, white.
Aux input—Video input, yellow.
10 Menu—Accesses main menu (DVDs only).
11 Enter—Confirms a selection.
12 Play—Begins or resumes playback.
13 Stop—Stops playback.
14 Infrared sensor—For use with DVD remote control only. Does not
operate with the ClearVue system remote.
Page 21
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 6
Operating the System
Advanced Functions
• “Chapter remain”—Chapter remaining time.
Using the Headphones
To display status information for audio CDs:
Press the DISP button repeatedly to cycle through the following
information:
IR
Transmitter
Dome
• “Single elapsed”—Track time.
• “Single remain”—Track remaining time.
• “Total elapsed”—Disc time.
• “Total remain”—Disc remaining time.
• Display off.
Using the headphones with your system allows rear-seat
passengers to listen to their DVD or video game without
disturbing front-seat passengers. When using the headphones the
IR transmitter dome must have a direct line of sight to the
headphones to work properly.
Viewing Options
Camera Angle
The system comes with two wireless IR headphones that receive a
signal from the IR transmitter dome near the overhead console.
Some DVD discs contain scenes with more than one viewing
angle. For these discs, the same scene can be viewed from a
different angle by using the ANGLE button on the remote
control.
To view a scene from another angle:
1 During DVD playback, press the ANGLE button.
“ANGLE x/y” appears in the monitor, where x represents the
current camera angle and y represents the total available
camera angles.
Volume
Power LED
Power ON/OFF
To turn the headphones on and off, push the Power ON/OFF
button on the right ear piece. The Power LED on the left ear
piece indicates when headphone power is on. Power turns off
automatically after 3 minutes of no audio to preserve battery life.
2 Press the ANGLE button again to cycle through all available
camera angles until the preferred angle is selected.
Note: This function is only available on DVDs that contain
multiple viewing angles.
To adjust the headphone volume, rotate the thumb wheel switch
on the headphones.
The wireless IR headphones require twoAAAbatteries. To replace
Page 7
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 20
Advanced Functions
Operating the System
DVD Menus
the batteries, remove the battery compartment cap on the right
earpiece and insert batteries, as shown.
Most DVD discs have unique menu structures. DVD menu
contents and operation may differ from disc to disc.
To use DVD menus:
1 During DVD playback, press the MENU button. The DVD
menu available on the disc appears on the screen.
2 Use the up, down, left and right arrows to select the preferred
menu option.
3 Press PLAY/PAUSE when the desired option is selected.
Title Menu
Some DVD discs also include more than one title.
To change titles:
Using the Car Speakers
To listen to system audio through your car speakers:
1 Insert a disc.
1 During DVD playback, press the TITLE button. A list of the
titles available on the DVD appears on the screen.
2 Turn on the car radio.
2 Use the up, down, left and right arrows to select a title.
3 Press the ENTER button when the desired option is selected.
Display Menu
3 Tune the car radio to the FM frequency 88.7; this is the default
system frequency.
If audio from the system does not play over the car speakers:
The DISPLAY function enables you to view the status, current
title number, track number and the total playing time of the disc
on the monitor.
1 Press SPEAKER ON/OFF on the remote control until “FM ON”
appears on the screen.
and /or
To display status information for VCDs and DVDs:
2 Tune the radio to 89.1 FM. This is an alternate system fre-
quency.
Press the DISP button repeatedly to cycle through the following
information on the monitor:
To turn off audio over the car speakers, press SPEAKER ON/OFF
on the remote.Audio from the system is then available over the
headphones only.
• “Title x/y and Chapter x/y”—Title elapsed time, where x is the
current chapter or title and y is the total number of chapters
or titles.
Note: Leaving the system to SPEAKER ON mode will
reduce the performance of normal radio reception. To
receive the best reception, always turn the system to
SPEAKER OFF when not in use.
• “Title remain”—Title remaining time.
• “Chapter elapsed”—Chapter elapsed time.
Page 19
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 8
Operating the System
Advanced Functions
To access the parental control rating system:
Using the TV Tuner
1 Press the SETUP button. The Setup menu appears.
To view television on the system:
1 Press MODE on the remote control until “TV
Mode” appears on the screen.
2 Use the up and down arrows to highlight “Parental Control”
and press PLAY/PAUSE twice to confirm your selection.
3 Use the up and down arrows to highlight “Parental”.
2 Press the up and down arrow buttons on the remote to change
channels.
4 To set a parental control level, press the right arrow and then
use the up and down arrows to highlight the desired level of
control.
3 Press MODE on the remote twice to return to DVD Mode.
Note: Broadcast television reception varies with location,
terrain, distance from the broadcast tower, and other
factors. Signal quality is likely to vary in a moving vehicle.
5 Press PLAY/PAUSE twice to confirm your selection.
“Input pwd” appears, prompting you to enter a password.
6 Enter a four-digit password and press PLAY/PAUSE twice to
confirm your selection. The factory default password is 0000.
7 Press SETUP to exit the Setup menu and begin playback.
To change the password:
1 Press the SETUP button. The Setup menu appears.
2 Use the up and down arrows to highlight “Parental Control”
and press PLAY/PAUSE twice to confirm your selection.
3 Use the up and down arrows to highlight “Password”.
4 Press the right arrow to highlight “Change” and press PLAY/
PAUSE.
4 Enter the existing four digit password using the number
buttons on the remote. The factory default password is 0000.
5 Enter a new four digit password.
6 Enter the new password again to confirm it.
7 Press SETUP to exit the Setup menu and begin playback.
Page 9
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 18
Advanced Functions
Remote Control Reference
• “Pic mode”—
Remote Control Reference
“Auto”: Automatically adjusts screen.
The ClearVue system remote control includes the following
features. Only the buttons labeled below are active.
“Hi-resolution”: Enhances screen image.
“N-flicker”: Prevents screen trembling.
Video Menu
• “Angle mark”—When playing DVDs that can be viewed from
different angles, a camera icon appears on the upper part of
the screen.
Power
Mode
Eject
Mute
• “Captions”—Turns on or off subtitles.
• “Scr saver”—Activates screen saver after 10 minutes of
inactivity. After 1 hour the DVD Tuner enters standby mode.
Audio Setup
Speaker On/Off
Channel Up
• “Digital out”—Adjusts the output for the digital audio terminal.
Menu
Adjustment
Menu
Adjustment
• “Dynamic range”—Dolby Digital sound. Use when it is difficult to
hear dialogues through the stereo or TV. This feature is only
supported by DVD titles with DRC properties.
Channel Down
Exit
• “Downmix”—Controls stereo and two channel audio.
“LT/RT”: Select when the amplifier has Dolby Pro Logic
support.
Previous
Track
Next Track
Play/Pause
“Stereo”: Select when listening to general stereo sound.
“VSS (Virtual Surround System)”: Select when listening
through VSS.
Number
Buttons
Parental Control
Menu
Title
• “Parental”—If the current disc has a parental code, it is
possible to skip or substitute various scenes not suitable for
young children.
Fast Forward
Stop
Rewind
Slow
• “Password”—Create and change password necessary for
parental control feature.
• “Default”—Returns DVD player to default settings. The user
must know the current password to do so.
Advanced
Functions
The Parental Control feature interacts with the DVD rating, if
available on the DVD, to enable parents to limit DVD playback.
Page 17
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 10
Remote Control Reference
Advanced Functions
Remote Control Battery Replacement
Advanced Functions
The ClearVue system remote requires two AAA batteries.
Replace the batteries as shown below.
Customize Settings
Use the Setup menu to personalize operation of your DVD
player. Setup includes options for various Language, Display,
Audio, and Parental Control features. The features are
described below.
1 Press the SETUP button. The Setup menu appears.
2 Use the arrow keys to highlight your selection and press
PLAY/PAUSE to confirm your selection.
3 Press SETUP again to begin playback.
Language Setup
Using the Remote Control
When using the remote control, always aim at the infrared
sensor on the overhead monitor.
• “OSD Language”—Selects language used in Setup menu.
• “Audio”—Selects the language of DVD audio.
• “Subtitle”—Selects the caption language.
• “Disc menu”—Selects the DVD menu language.
This unit is designed for use with DVD, VCD, CD, CD-R, and
CD-RW, and with MP3 or MPEG-1 file recordings. Functions on
the remote control will vary depending on the features available
on the disc you are playing. If a function is unavailable on the
inserted CD, VCD, or DVD, the following symbol appears on the
on-screen display:
Note: Audio, Subtitle, and Disc menu can only be adjusted
when playback is stopped.
Display Setup
• “TV display”—
“Normal/PS”: When viewing a 16:9 image on a 4:3 screen the
sides are cropped.
If a disc is incompatible with the unit or if the disc is loaded
incorrectly, you may see one of the following on the on-screen
display:
“Normal/LB”: When viewing a 16:9 image on a 4:3 screen, a
black bar appears on the top and bottom of the screen and
the complete image is shown.
• “No disc” — Check to see that the disc is loaded with the
“Wide”: Use when connecting to a wide-screen TV.
label side up.
• “TV type”—
• “Smart navigation” screen — The DVD player may be trying
“Multi”: Outputs the original PAL or NTSC signal recorded into
the title.
to read an incompatible disc. Check disc compatibility.
“NTSC”: Changes image signal to NTSC.
• Another error message indicating the disc is either
incompatible or loaded incorrectly.
“PAL”: Changes image signal to PAL. Do not use this setting.
Page 11
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 16
Basic Functions
Basic Functions
Changing View Settings
Basic Functions
To adjust settings for color, contrast, brightness, or tint:
Inserting or Ejecting Discs
Press the EJECT button to insert or eject a disc.
Playback
1 Press VIDEO MENU on the remote. The following menu
appears in the screen.
***MENU***
To play a disc:
(32)
(32)
(32)
(32)
COLOR
CONTRAST
BRIGHT
TINT
1 Press the EJECT button to open the DVD player.
2 Load the disc with the label side up.
3 Press EJECT again. “Disc loading” appears on the screen.
The disc commences playback automatically.
2 Press the up and down arrow keys on the remote to highlight
a menu option. Each menu option has a range of values from
0 to 63, with 32 as the default.
DVD playback varies from disc to disc. Options include:
• DVD playback begins automatically when you insert the disc.
• DVD playback begins automatically, but proceeds only until a
menu of options appears. To continue playback, highlight an
option using the arrow buttons then press PLAY/PAUSE on
the remote control.
3 Press the left arrow key on the remote to reduce a setting.
4 Press the right arrow key on the remote to increase a setting.
5 Press EXIT on the remote to close the menu. The menu also
• The screen displays a menu of options before proceeding. To
continue, highlight an option using the arrow buttons then
press PLAY/PAUSE on the remote control.
closes automatically after a few seconds.
Stop
1 Press the STOP button to stop playback. The DVD player
saves in internal memory the exact position where it stopped
and will playback again from that position.
2 Press PLAY/PAUSE to resume normal playback.
Note: For some VCDs, the Stop function can be enabled by
pressing the NEXT button.
Pause
1 Press the PLAY/PAUSE button to pause playback of the disc.
2 Press PLAY/PAUSE to resume playback.
Page 15
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 12
Basic Functions
Basic Functions
Mute
• Press the PREVIOUS TRK button during playback to skip
backward to the previous track or to the previous title/chapter.
1 Press the MUTE button once to mute the sound.
“Mute” appears on the monitor.
For VCDs and DVDS—“Chapter x/y” appears on the monitor,
where x is the current chapter and y is the total number of
chapters.
2 Press MUTE again to restore sound.
Fast Forward and Reverse Searching
For audio CDs—“Previous” appears on the monitor.
Repeating a Track or Chapter
1 Press the FAST button during playback to fast forward.
“FF 2x” appears on the monitor.
The DVD player will repeat a track or chapter, or an audio disc.
3 Press PLAY/PAUSE to resume regular play.
Press the REP button on the remote control to cycle through the
following on-screen display options.
Slow Forward and Reverse Searching
1 Press the SLOW button during playback to slow forward.
For DVDs:
“SF 2x” appears on the monitor.
• “Chapter repeat on”—The current chapter will be repeated.
• “Title repeat on”—The current title will be repeated.
• “Repeat off”—Repeat mode is off.
For audio/video CDs:
3 Press PLAY/PAUSE to resume regular play.
Note: Slow forward is not an option when playing audio CDs.
Searching One Scene or Track at a Time
1 Press the PLAY/PAUSE button to pause playback of the
disc.
• “Rep one”— The current track will be repeated.
• “Rep all”— The current disc will be repeated.
• “Repeat off”— Repeat mode is off.
2 Set the direction of the scene-by-scene search by using the
right or left arrow button.
3 Press PLAY/PAUSE to resume regular play.
Searching by Next or Previous Chapter or Track
Note: For MP3 CDs, press the REP button to change the play
mode.
• Press the NEXT TRK button during playback to skip forward
to the next track or to the next title/chapter.
For VCDs and DVDS—“Chapter x/y” appears on the
monitor, where x is the current chapter and y is the total
number of chapters.
For audio CDs—“Next” appears on the monitor.
Note: For MP3 discs, if the disc is stopped, press the up and
down arrows instead of the NEXT TRK or PREVIOUS
TRK buttons to select a song.
Page 13
Rosen Products
ClearVue 6821 DVD System Owner’s Manual
Page 14
|