FORM NO. G11-449 REV. 6
Supersedes Form No. G11-449 Rev. 5
GAS FURNACES
®
CRITERION II
80.0-82.2% A.F.U.E.✝
DOWNFLOW
GAS FURNACES
The Rheem® Criterion® II line of downflow gas furnaces is
designed for installation in closets, alcoves, utility rooms, or
attics. The design is certified by CSA.
Features
■ Patented heat exchanger, constructed of both stainless
and aluminized steel for the maximum in corrosion
resistance.
■ Low profile “34 inch” [864 mm] design is lighter and easier
to handle, and leaves room for optional equipment.
■ Left or right side gas and electric inlet connections with
quick, simple change.
■ Direct Spark ignition models and integrated board with
humidifier and electronic air cleaner hookups.
■ Insulated blower compartment helps to reduce jacket loss
and noise.
■ Pre-paint galvanized steel cabinet.
■ Molded permanent filter.
RGLH- SERIES
■ Grab-holes in doors to aid in easy door removal and
replacement.
Models with Input Rates from
A variety of cooling coils and plenums designed to use with
50,000 to 150,000 BTU/HR
[15 to 44 kW]
Rheem Criterion II gas furnaces are available as optional
accessories.
✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department of
Energy test procedures.
ENER UIDE
Annual Fuel Utilization Efficiency AFUE
-
THIS MODEL
80.0%
MID
78% 82%
HIGH
88%
97%
BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE
FROM YOUR RETAILER.
PHYSICAL DATA AND SPECIFICATIONS
MODEL NUMBERS
RGLH- SERIES
05EAUER
05NAUER
07EAUER
07NAUER
07EAMGR
07NAMGR
10EAMER
10NAMER
10EBRJR
10NBRJR
12EARJR
12NARJR
15EARJR
15NARJR
50,000 [15]
41,000 [12]
45,000 [13]
75,000 [22]
60,000 [18]
67,500 [19.8]
75,000 [22]
60,500 [18]
67,500 [19.8]
100,000 [29.3]
80,000 [23]
100,000 [29.3]
81,000 [24]
125,000 [36.6]
99,000 [29]
150,000 [44]
120,000 [35]
135,000 [39.6]
Input–BTU/Hr [kW] ➁
Heating Capacity BTU/Hr [kW] ➀
High Altitude Input [kW]
90,000 [26.4]
90,000 [26.4]
112,500 [33]
High Altitude Output
Capacity [kW]
36,500 [10.7]
.10 [.025]
53,500 [15.7]
.12 [.029]
54,000 [15.8]
.12 [.029]
72,000 [21.1]
.15 [.037]
72,500 [21.2]
.15 [.037]
89,000 [26.1]
.20 [.05]
107,500 [31.5]
.20 [.05]
Heat Ext. Static Pressure [kPa]
11 x 6 = 10*AU
[279 x 152]
11 x 7 = 10*AM
[279 x 178
11 x 6
[279 x 152]
11 x 6
[279 x 152]
11 x 7
[279 x 178]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
Blower (D x W) [mm]
Motor H.P. [W]–Speeds [W]–
PSC Type
1/2-4-PSC
[373]
1/2-4-PSC
[373]
3/4-4-PSC
[559]
1/2-4-PSC
[373]
3/4-4-PSC
[559]
3/4-4-PSC
[559]
3/4-4-PSC
[559]
Motor Full Load Amps
Heating Speed
6.8
7.1
9.5
7.1
9.5
9.5
9.5
MED-LOW
HIGH
MED-HIGH
HIGH
MED-LOW
MED-HIGH
MED-HIGH
HIGH
MED-LOW
MED-HIGH
MED-LOW
MED-HIGH
MED-LOW
MED-HIGH
Cooling Speed
Cooling CFM @ .5" [kPa] E.S.P.
(Nominal) [L/s]
1200
[566]
1200
[566]
1600
[755]
1200
[566]
2000
[944]
2000
[944]
2000
[944]
Rated E.S.P. (In. W.C.) [kPa]
.50 [.12]
.50 [.12]
.50 [.12]
.50 [.12]
.50 [.12]
.50 [.12]
.50 [.12]
55-85 = 10*AU
[30.6-47.2]
45-75 = 10*AM
[25-41.7]
Temperature Rise Range °F
[°C]
25-55
[13.9-30.6]
40-70
[22.2-38.9]
25-55
[13.9-30.6]
40-70
[22.2-38.9]
40-70
[22.2-38.9]
50-80
[27.8-44.4]
Max. Outlet Air Temp. °F
[°C]
155
[68.3]
165
[73.9]
155
[68.3]
190
[87.8]
190
[87.8]
180
[82.2]
190
[87.8]
(1) 14 x 20
[356 x 508]
(2) 12 x 20
[305 x 508]
(2) 12 x 20
[305 x 508]
(2) 12 x 20
[305 x 508]
(2) 14 x 20
[356 x 508]
(2) 14 x 20
[356 x 508]
(2) 14 x 20
[356 x 508]
Standard Filter [mm]
Approx. Shipping Weight (Lbs.)
[kg]
85
[38.6]
105
[47.6]
105
[47.6]
115
[52.2]
120
[54.4]
140
[63.5]
150
[68.0]
82.2%
80.5%
81.1%
80.2%
80%
80%
80%
AFUE–Electric Ignition Models ➀
California Seasonal Efficiency–
Electric Ignition Nox Models
75.9/76.2
74.4/74.9
75.1/75.5
75.2/75.2
74.7/74.7
75.2/75.3
76.0/75.9
NOTES: All models are 115V, 60HZ, 1Ø
. Gas connection size for all models is 1/2" N.P.T.
➀ In accordance with D.O.E. test procedures.
➁ See Conversion Kit Index Form No. 92-21519-52 for U.S. models and Form No. 92-21519-53 for Canadian models for high altitude derate.
MODEL IDENTIFICATION—DOWNFLOW MODELS
R
G
L
H
07E
A
U
E
R
—
Rheem
Gas
Furnace
Downflow Design
Series
Heating Input Designation
Variations
A = Std.
Cabinet
B = Wide
Cabinet
Blower
Designation
Heating & Cooling
Designation
S = 500-1200 CFM
[236-566 L/s]
E = 1100-1330 CFM
[519-628 L/s]
G = 1450-1750 CFM
[684-826 L/s]
Fuel Type
R = Natural Gas,
U.S. and
Electric
Ignition Model
NO
Input
BTU/HR
x
U = 11 x 6
[279 x 152 mm]
M = 11 x 7
[279 x 178 mm]
R = 11 x 10
[279 x 254 mm]
Canadian
Standard
Furnace
05E
07E
10E
12E
15E
05N
07N
10N
12N
15N
50,000 [15 kW]
75,000 [22 kW]
100,000 [29 kW]
125,000 [37 kW]
150,000 [44 kW]
J = 1800-2075 CFM
[850-979 L/s]
[
] Designates Metric Conversions
Rheem Manufacturing Company
3
DOWNFLOW DIMENSIONS
TABLE 1. DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]
REDUCED CLEARANCES (IN.) [mm]
MODEL
RGLH-
SERIES
A
B
C
D
E
LEFT
SIDE
RIGHT
SIDE
SHIP. WGTS.
(LBS.) [kg]
BACK
TOP
FRONT
VENT
05
07
14 [356]
171/2 [445]
171/2 [445]
21 [533]
241/2 [622]
241/2 [622]
1227/32 [326]
1611/32 [415]
1611/32 [415]
1927/32 [504]
2311/32 [593]
2311/32 [593]
103/8 [264]
121/8 [308]
121/8 [308]
137/8 [352]
155/8 [397]
155/8 [397]
➀
➀
➀
➀
➀
➀
131/8 [333]
165/8 [422]
165/8 [422]
201/8 [511]
235/8 [600]
235/8 [600]
0
0
0
0
0
0
0
0
0
0
0
0
1 [25]
1 [25]
1 [25]
1 [25]
1 [25]
1 [25]
3 [76]
3 [76]
3 [76]
3 [76]
3 [76]
3 [76]
85 [38.6]
105 [47.6]
115 [52.2]
120 [54.4]
140 [63.5]
150 [68]
4 ➁
3 ➁
3 ➁
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
10 (A)
10 (B)
12
0
0
0
15
NOTES: ➀ May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.
➁ May be 0" [0 mm] with type B vent.
➂ May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with ANSI Z21.47-1993 • CAN/CGA-2.3-M93 venting table guidelines, and in accordance with local codes.
[
] Designates Metric Conversions
4
Rheem Manufacturing Company
BLOWER PERFORMANCE DATA—DOWNFLOW MODELS
MODEL
NUMBER
RGLH-
CFM [L/s] AIR DELIVERY
BLOWER
SIZE
[mm]
MOTOR
H.P.
[W]
BLOWER
SPEED
EXTERNAL STATIC PRESSURE INCHES [kPa] WATER COLUMN
.1 [.02]
.2 [.05]
.3 [.07]
.4 [.10]
.5 [.12]
.6 [.15]
.7 [.17]
SERIES
LOW
735 [347]
715 [337]
1015 [479]
1165 [550]
1330 [628]
690 [326]
995 [470]
1150 [543]
1310 [618]
660 [311]
975 [460]
1130 [533]
1295 [611]
635 [300]
955 [451]
1100 [519]
1265 [597]
605 [286]
930 [439]
1075 [507]
1235 [583]
575 [271]
905 [427]
1040 [491]
1205 [569]
05MAUER
05EAUE
05NAUER
11 x 6
[279 x 152]
1/2
[373]
MED-LO 1025 [484]
MED-HI 1185 [559]
HIGH
1345 [635]
LOW
835 [394]
990 [467]
820 [387]
975 [460]
1125 [531]
1290 [609]
800 [378]
955 [451]
1105 [522]
1265 [597]
775 [366]
935 [441]
1080 [510]
1245 [588]
750 [354]
905 [427]
1050 [496]
1215 [573]
720 [340]
875 [413]
1020 [481]
1180 [557]
685 [323]
835 [394]
980 [463]
1140 [538]
07MAUER
07EAUE
07EAUER
11 x 6
[279 x 152]
1/2
[373]
MED-LO
MED-HI 1140 [538]
HIGH
1300 [614]
LOW
1210 [571]
1205 [569]
1560 [736]
1880 [887]
2050 [967]
1195 [564]
1550 [732]
1825 [861]
1995 [942]
1180 [557]
1530 [722]
1790 [845]
1940 [916]
1165 [550]
1495 [706]
1740 [821]
1885 [890]
1155 [545]
1465 [691]
1675 [791]
1835 [866]
1130 [533]
1430 [675]
1600 [755]
1770 [835]
07MAMGR
07EAMG
07NAMGR
11 x 7
[279 x 178]
3/4
[559]
MED-LO 1580 [746]
MED-HI 1915 [904]
HIGH
—0000
*
*
*
LOW
935 [441]*
910 [429]*
1055 [498]
1210 [571]
1395 [658]
885 [418]*
1040 [491]
1190 [562]
1370 [647]
855 [404]*
1010 [477]
1165 [550]
1340 [632]
825 [389]*
980 [463]
1135 [536]
1305 [616]
785 [370]*
945 [446]
1095 [517]
1265 [597]
760 [359]*
905 [427]
1055 [498]
1220 [576]
11 x 7
1/2
MED-LO 1070 [505]
MED-HI 1240 [585]
10EAME*
10NAMER
[279 x 178]
[373]
HIGH
1420 [670]
LOW
1330 [628]
1295 [611]
1670 [788]
2085 [984]
2410 [1137]
1285 [606]
1655 [781]
2055 [970]
2355 [1111]
1245 [588]
1615 [762]
2005 [946]
2305 [1088]
1225 [578]
1585 [748]
1970 [930]
2240 [1057]
1205 [569]
1565 [739]
1945 [918]
2165 [1022]
1160 [547]
1525 [720]
1880 [887]
2100 [991]
10EBRJR
10NBRJR
11 x 10
[279 x 254]
3/4
[559]
MED-LO 1690 [798]
MED-HI
HIGH
—0000
—0000
LOW
MED-LO
MED-HI
HIGH
1330 [628]
—0000
1295 [611]
1690 [798]
2090 [986]
2395 [1130]
1280 [604]
1660 [783]
2035 [960]
2335 [1102]
1240 [585]
1635 [772]
1985 [937]
2260 [1067]
1215 [573]
1580 [746]
1930 [911]
2185 [1031]
1210 [571]
1535 [724]
1850 [873]
2080 [982]
1175 [555]
1480 [698]
1785 [842]
1965 [927]
12EARJR
12NARJR
11 x 10
[279 x 254]
3/4
[559]
—0000
—0000
LOW
1300 [614]
1280 [604]
1650 [779]
2075 [979]
2340 [1104]
1230 [580]
1620 [765]
2035 [960]
2290 [1081]
1205 [569]
1570 [741]
1990 [939]
2215 [1045]
1170 [552]
1545 [729]
1955 [923]
2145 [1012]
1115 [526]
1485 [701]
1900 [897]
2080 [982]
1030 [486]
1425 [673]
1815 [857]
1995 [942]
15MARJR
15EARJR
15NARJR
11 x 10
[279 x 254]
3/4
[559]
MED-LO 1675 [791]
MED-HI 2105 [993]
HIGH
—0000
NOTES: *Not to be used as a heating speed.
Data compiled with factory filters installed.
[
] Designates Metric Conversions
Rheem Manufacturing Company
5
ACCESSORIES—DOWNFLOW
DOWNFLOW WARNING: Unit design is certified for installation on non-com-
bustible floor. A special factory supplied combustible floor sub-base is
required when installing on a combustible floor. Failure to install the sub-base
may result in fire, property damage and personal injury.
PLENUM DATA—“A” COILS
Plenum adapters are required in some instances for use on downflow applications
when plenum and furnace size do not match.
FURNACE
WIDTH
PLENUM
WIDTH
PLENUM ADAPTER
DOWNFLOW
COIL
PLENUM
COMBUSTIBLE FLOOR BASE DIMENSIONS
IN. [mm]
IN. [mm]
14 [356]
14 [356]
171/2 [445]
171/2 [445]
171/2 [445]
171/2 [445]
21 [533]
21 [533]
241/2 [622]
241/2 [622]
161/4 [413]
201/4 [514]
161/4 [413]
201/4 [514]
215/8 [549]
251/4 [641]
221/4 [565]
251/4 [641]
251/4 [641]
215/8 [549]
RXAA-C178
RXAA-C179
RXAA-C186
RXAA-C180
RXAA-C189
RXAA-C181
RXAA-C182
RXAA-C183
RXAA-C184
RXAA-C190
RXAL-B16BU
RXAL-B20BU
RXAL-B16BU
RXAL-B20BU
RXAL-B21BU
RXAL-B25BU
RXAL-B22BU
RXAL-B25BU
RXAL-B25BU
RXAL-B21BU
COMBUSTIBLE
FLOOR BASE
USE WITH
A
B
C
FURNACE SIZES
IN. [mm] IN. [mm] IN. [mm]
RXGC-B14
RXGC-B17
RXGC-B21
RXGC-B24
RGLH-05
141/2 [368] 131/4 [337] 111/4 [286]
RGLH-07, RGLH-10(-)A 18 [457] 163/4 [425] 143/4 [451]
RGLH-10(-)B
RGLH-12, RGLH-15
211/2 [546] 201/4 [514] 181/4 [464]
25 [635] 233/4 [603] 213/4 [552]
NOTE: See Form Number C11-206 for MultiFlex coil data.
RXPF-F01 and F02
FOSSIL FUEL KITS—are for use
with Rheem Heat Pumps and
Criterion II warm air furnaces. The
RXPF-F02 meets TVA requirements.
RXGF-CC*
FILTER RACK—Downflow top
return mount.
NOTE: Filter racks are shipped
without filters.
*Filters available through
PROSTOCK™.
OPTION CODE FOR HIGH
ALTITUDE: US-277
Canada-298
(Kit packaged with furnace.
Requires field installation.)
GENERAL TERMS OF LIMITED WARRANTY
Rheem will furnish a replacement for any part of this product
which fails in normal use and service within the applicable
period stated, in accordance with the terms of the limited
warranty.
Gas Heat Exchanger Limited Warranty .......Twenty (20) Years
*Any Other Part..............................................One (5) Years
*This five year limited warranty is applicable only to single-phase products
installed in residential applications on or after January 1, 2001.
For Complete Details of the Limited Warranty, Including Applicable Terms
and Conditions, See Your Local Installer or Contact the Manufacturer for
a Copy.
6
Rheem Manufacturing Company
NOTES
Rheem Manufacturing Company
7
RHEEM
AIR CONDITIONING
DIVISION
Before proceeding with installation, refer
to installation instructions packaged
with each model, as well as complying
with all Federal, State, Provincial, and
Local codes, regulations, and practices.
5600 Old Greenwood Road, Fort Smith, Arkansas 72908
“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”
PRINTED IN U.S.A.
11-01 DC
FORM NO. G11-449 REV. 6
Supersedes Form No. G11-449 Rev. 5
|