S8 Series II
S8 AutoSet Spirit™ II
S8 Elite™ II
POSITIVE AIRWAY PRESSURE DEVICES
User Guide
English
ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia
ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA
ResMed (UK) Ltd (EU Authorized Representative) 96 Milton Park Abingdon Oxfordshire OX14 4RY UK
ResMed Offices Australia, Austria, Belgium, Brazil, China, Finland, France, Germany, Greece, Hong Kong, India, Ireland, Italy, Japan, Malaysia, Mexico,
Protected by patents: AU 691200, AU 697652, AU 709279, AU 724589, AU 730844, AU 736723, AU 750095, AU 750761, AU 764761, AU 779327, AU
2002231456, CN 02804930.6, EP 0651971, EP 0661071, EP 0920845, EP 0934723, EP 1028769, EP 1126893, EP 1502618, EP 1144036, JP 3580776, JP
3778797, NZ 504595, US 5199424, US 5245995, US 5522382, US 5704345, US 6138675, US 6240921, US 6363933, US 6367474, US 6425395, US
6502572, US 6591834, US 6705315, US 6745768, US 6817361, US 6988498, US 7040317, US 7100608. Other patents pending.
Protected by design registrations: AU 302180, AU 302181, AU 302182, AU 302183, AU 302184, AU 302185, AU 302186, CN 200430121212.2, CN
200430121213.7, CN 200430121211.8, CN 200430121214.1, CN 200430121215.6, CN 200430121216.0, CN 200430121217.5, EU 269436, EU 815071, HK
0412901.9, JP 1257662, JP 1257663, JP 1266956, JP 1266957, JP 1267270, JP 1267271, NZ 405614, NZ 406923, NZ 406924, NZ 406925, NZ 406926, NZ
406927, NZ 406928, US D544598, US D553228, US D557406, US D557407, US D560795, US D561891, US D565160. Others pending.
S8, S8 AutoSet, S8 Elite and SmartStart are trademarks of ResMed Ltd and AutoSet and HumidAire are registered in U.S. Patent and
Trademark Office.
© 2008 ResMed Ltd.
338571-Eng/2 08 11
Introduction
S8 AutoSet Spirit II
The S8 AutoSet Spirit II self-adjusting sleep apnea system is indicated for the treatment
of obstructive sleep apnoea (OSA) in adult patients. The S8 AutoSet Spirit II self-
adjusting sleep apnoea system has two treatment modes: AutoSet and fixed-pressure
CPAP. The S8 AutoSet Spirit II system is intended for home and hospital use.
S8 Elite II
The S8 Elite II continuous positive airway pressure (CPAP) system is indicated for the
treatment of obstructive sleep apnoea (OSA) in adult patients. The S8 Elite II CPAP
system is intended for home and hospital use.
Contraindications
Your S8 Series II is not a life-support device and may stop operating during power
failure or certain fault conditions. It should not be used by patients who are dependent
on continuous therapy.
Positive airway pressure therapy may be contraindicated in some patients with the
following pre-existing conditions:
•
•
•
•
•
severe bullous lung disease
pneumothorax
pathologically low blood pressure
dehydration
cerebrospinal fluid leak, recent cranial surgery, or trauma.
Adverse Effects
Patients should report unusual chest pain, severe headache, or increased
breathlessness to their prescribing physician. An acute upper respiratory tract infection
may require temporary discontinuation of treatment.
The following side effects may arise during the course of therapy with the CPAP device:
•
•
•
•
•
•
•
drying of the nose, mouth, or throat
nosebleed
bloating
ear or sinus discomfort
eye irritation
skin rashes
chest discomfort.
Introduction
1
Parts of the S8 Series II system
Your S8 Series II device comprises:
•
•
•
•
S8 Series II device
Power cord
Premium carry bag
2 m air tubing.
Optional components include:
•
•
•
•
•
Integrated humidifier
Front cap
3 m air tubing
DC-12 converter
ResMed Tubing Wrap.
Carry handle
Screen
Keypad
Data Card
slot
DC
AC
Air outlet
Masks
A list of masks (and their settings) compatible with these devices can be found on
Humidifiers
A list of humidifiers compatible with ResMed devices can be found on
ResScan Data Card
The ResScan Data Card may be used with the S8 Series II either to help your clinician
monitor your treatment or provide you with updates to your device settings.
2
Using the S8 Series II
Setting Up
1
2
3
4
Connect the power cord to the socket at the rear of the S8 Series II device.
Plug the other end of the power cord into the power outlet.
Connect one end of the air tubing firmly onto the air outlet.
Connect the assembled mask system to the free end of air tubing.
For information on assembling your mask, see your mask manual.
2
1
3
4
WARNING
!
!
•
Make sure the power cord and plug are in good condition and the
equipment is not damaged.
•
Only ResMed air tubing should be used with the device. A different type
of air tubing may alter the pressure you actually receive, reducing the
effectiveness of your treatment.
•
Blocking the hose and/or air inlet of the device while in operation could
lead to overheating of the device.
CAUTION
•
Be careful not to place the device where it can be bumped or where
someone is likely to trip over the power cord.
•
If you put the device on the floor, make sure the area is free from dust
and clear of bedding, clothes or other objects that could block the air
inlet.
•
Make sure the area around the device is dry and clean.
Using the S8 Series II
3
How to Use the Control Panel
LCD screen
Keypad
Start/Stop key
The control panel of the S8 Series II includes an LCD screen which displays the
menus and treatment screens as well as a keypad for navigating through the
menus and delivering treatment.
The S8 Series II keypad has the following keys:
Key
Function
Starts or stops treatment.
Start/Stop
Allows you to increase settings options and scroll through
the S8 Series II menu.
Up
Allows you to decrease settings options and scroll through
the S8 Series II menu.
Down
Left
Performs the function indicated by the guiding text
displayed above it on the LCD screen (eg, change).
Performs the function indicated by the guiding text
displayed above it on the LCD screen (eg, exit).
Right
The keypad and LCD are equipped with backlights that come on when the device
is powered. The LCD backlight turns off after two minutes of inactivity, and
comes back on when you press a key. The keypad backlight is always on while
the S8 Series II is on.
Selecting the Mask Type
To ensure your device functions as intended with your selected mask, you need to
select the mask type that you are using.
1
With the RAMP or SETTLING screen displayed, press
standby screen displays RAMP. In AutoSet mode (S8 AutoSet Spirit II only) the
standby screen displays SETTLING.)
. (In CPAP mode, the
Press
Press
until MASK is displayed.
to change the setting.
2
3
4
Press
Press
or
until you see the setting that you require.
4
5
to apply.
Using the Mask-fitting Feature
You can use the S8 Series II mask-fitting feature to help you fit your mask properly. This
feature delivers air pressure for a three-minute period, prior to starting treatment,
during which you can check and adjust your mask fit to minimise leaks.
Note: Make sure that the mask setting on the MASK screen is the same as the mask
you are using.
1
2
Fit your mask as described in the mask user instructions.
With the RAMP or SETTLING screens displayed, hold down
three seconds until air pressure delivery starts.
for at least
Your device will ramp to the mask-fit pressure and will remain at this pressure
for three minutes.
The following displays on the LCD screen indicating that the mask-fitting feature
is operating, where: ***** is an excellent fit;****- is a very good fit; ***-- is a
good fit; while **---, *---- and ----- each require you to adjust your mask.
MASK FIT:
*****
excelnt
3
Adjust your mask, mask cushion and headgear until you have a secure and
comfortable fit.
After three minutes, the pressure reverts to the set pressure and treatment will
begin. If you do not wish to wait three minutes, hold down
three seconds to start treatment immediately.
for at least
If you press
for less than three seconds, the unit will return to standby
mode (the RAMP or SETTLING screen).
Starting Treatment
1
Make sure the power is on.
The product name is displayed briefly on the screen, then the standby screen
displays RAMP (or SETTLING). The key and LCD backlights also turn on.
Lie down and arrange the air tubing so that it is free to move if you turn in your
sleep.
2
CAUTION
!
Do not leave long lengths of air tubing around the top of your bed. They could
twist around your head or neck while you are sleeping.
Alter the ramp or settling time if required.
3
Using the S8 Series II
5
To start treatment, press
.
4
5
Fit your mask as described in the mask user instructions.
WARNING
!
A mask should not be used unless the S8 Series II device is powered and
operating properly.
Stopping Treatment
To stop treatment at any time, remove your mask and press
.
If your clinician has enabled SmartStart, simply remove your mask and treatment will
end.
Changing the Settings on your S8 II Device
You can change settings (such as Ramp Time, EPR Level) on S8 II devices by using the
keypad and LCD. When the device is in standby mode you can display a series of
screens (a menu) on the LCD screen in order to view and change the settings for a
particular function.
The Standard Menu
Your clinician will have enabled a standard menu on your S8 Series II device. The figure
below shows the standard menu in each mode.
To enter the standard menu from the standby (RAMP or SETTLING) screen,
press
.
CPAP
AUTOSET
WELCOME
>>>>>>
WELCOME
>>>>>>
SETTLING: 10min
menu
RAMP: 10min
menu
*
*
EPR LEVEL: 1
change
EPR LEVEL: 1
change
exit
exit
USED HRS: 08000
exit
USED HRS: 08000
exit
USAGE: 1000/1068
exit
USAGE: 1000/1068
exit
MASK: ULTRA
MASK: ULTRA
change
exit
change
exit
SW: SX4800100
exit
SW: SX4800100
exit
* Only displayed if access set by clinician.
Note: The AutoSet menu is available on the S8 AutoSet Spirit II only.
6
The Detailed Menu
Your clinician may have enabled a detailed menu on your S8 Series II device. The figure
below shows the detailed menu in each mode.
To enter the detailed menu from the standby (RAMP or SETTLING) screen, press
.
WELCOME
>>>>>>
WELCOME
>>>>>>
CPAP
AUTOSET
SETTLING: 10min
menu
RAMP: 10min
menu
CPAP
AUTOSET
SETTINGS
enter
exit
*
*
EPR LEVEL: 1
EPR LEVEL: 1
change
change
exit
exit
exit
MASK: ULTRA
change
MASK: ULTRA
change
exit
TUBE LENGTH: 2m
TUBE LENGTH: 2m
change
exit
exit
change
exit
exit
HUMID: NONE
change
HUMID: NONE
change
SMARTSTART: ON
SMARTSTART: ON
change
exit
change
exit
LEAK ALERT: OFF
LEAK ALERT: OFF
change
exit
change
exit
RESULTS
enter
exit
USED HRS: 08000
exit
USAGE: 1000/1068
exit
*
SMART DATA
enter
exit
OPTIONS
enter
exit
*
*
AUTO APPEAR: OFF
SMART DATA
enter
change
cancel
exit
LANG: ENGLISH
change
exit
SERVICING
enter
exit
SN: 12345678912
exit
PCB: 123456789123
4567
exit
exit
SW: SX4800100
* Only displayed if access set by clinician.
Note: The AutoSet menu is available on the S8 AutoSet Spirit II only.
Changing the Settings on your S8 II Device
7
Messages on the S8 Series II LCD
Your clinician may have set your S8 Series II device to remind you about important
events, such as when to replace your mask, when to insert your Data Card (if your
device is Data Card enabled) and so on.
The reminder message is displayed on the LCD and is visible if the device is not
delivering therapy. The backlight on the LCD flashes when a message is displayed.
Your clinician can set any of the following reminders on your LCD:
Message
Description
Action
INSERT
CARD
May appear if your device is
Data Card enabled.
Insert your Data Card and follow any
instructions that your clinician has given you.
When you have done this, the message will
disappear from the LCD. Pressing
will also remove the message.
(Ok)
REPLACE
MASK
May appear when your mask
is due for replacement.
Press
(Ok) to remove the message
from your LCD, and replace your mask with a
new one.
CALL
PROVIDER
May appear as a reminder to
contact your clinician, eg, to
discuss how your therapy is
going.
Press
(Ok) to remove the message
from your LCD, and contact your clinician.
REPLACE
FILTER
May appear as a reminder to
replace the air filter on your
device.
Press
(Ok) to remove the message
from your LCD, and replace the air filter.
SERVICE
DUE
May appear as a reminder to
return your device for service.
Press
(Ok) to remove the message
from your LCD, and contact your clinician.
Using the Data Card to Collect Data
If your clinician needs to review your treatment, they will ask you to use the Data Card
to copy data from your S8 Series II, and to return the card to them.
Copying Data onto the Data Card
1
Switch on the S8 Series II and wait until you see the standby (Ramp or Settling)
screen.
2
Hold the Data Card with the arrow facing up and insert it into the Data Card slot
until it stops. Data copying starts automatically.
The “Card Inserted Please Wait” message is displayed on the S8 Series II LCD
while data is being copied. Copying takes approximately five seconds.
The “Copy Complete Remove Card” message is displayed on the LCD when
copying has finished.
8
3
4
5
Remove the Data Card by gripping the end of the Data Card and pulling it out.
Store the Data Card in its protective folder when not in use.
Return the card in its protective folder to your clinician using a postal envelope.
Updating Settings on your S8 device
If your clinician has provided a Data Card with new device settings:
1
With the device in standby (Ramp or Settling) mode, insert the Data Card into the
Data Card slot. Updating will start automatically.
The “Card Inserted Please Wait” message is displayed on the LCD while
updating is in progress. Updating takes approximately five seconds.
The “Settings Success Remove Card” message is displayed on the LCD if the
settings were updated successfully.
Note: This message only appears once. If you re-insert the Data Card after you
have updated your settings, this message is not displayed.
2
3
Remove the Data Card from the S8 Series II.
Store the Data Card in its protective folder when not in use.
WARNING
!
If your clinician has told you to use this Data Card to update the settings on
your device and the “Settings Success” message does not appear, contact
your clinician immediately.
Cleaning and Maintenance
Daily
Disconnect the air tubing and hang it in a clean, dry place until next use.
Weekly
1
2
3
4
Remove the air tubing and wash it in warm water using mild detergent.
Rinse thoroughly, hang, and allow to dry.
Before next use, reassemble the mask and headgear.
Reconnect the air tubing.
Monthly
1
2
Clean the exterior of the S8 Series II with a damp cloth and mild liquid soap.
Check the air filter for holes and blockage by dirt.
Cleaning and Maintenance
9
WARNING
!
!
Beware of electric shock. Do not immerse the device or power cord in water.
Always unplug the device before cleaning and make sure it is dry before
reconnecting.
CAUTION
•
Do not hang the air tubing in direct sunlight as it may harden over time
and eventually crack.
•
Do not use bleach, chlorine, alcohol, or aromatic-based solutions,
moisturising or antibacterial soaps or scented oils to clean the air tubing
or the device. These solutions may cause hardening and reduce the life
of the product.
Replacing the Air Filter
Replace the air filter every six months (or more often if necessary).
1
Remove the air filter cover at the back of the device.
Air filter cover
2
3
4
Remove and discard the old air filter.
Insert a new filter with the blue tinted side facing out from the device.
Replace the air filter cover.
CAUTION
!
•
•
Do not wash the air filter. The air filter is not washable or reusable.
The air filter cover protects the device in the event of accidental liquid
spillage onto the device. Ensure the air filter and air filter cover are fitted
at all times.
Servicing
This product (S8 AutoSet Spirit II; S8 Elite II) should be inspected by an authorised
ResMed service centre five years from the date of manufacture. Prior to this, the device
is intended to provide safe and reliable operation provided that it is operated and
maintained in accordance with the instructions provided by ResMed. Applicable
ResMed warranty details are provided with the device at the time of original supply. Of
course, as with all electrical devices, if any irregularity becomes apparent, you should
exercise caution and have the device inspected by an authorised ResMed service
centre.
If you feel that your device is not performing properly, see “Troubleshooting” on page
12.
10
CAUTION
!
•
Do not attempt to open the S8 Series II case. There are no user
serviceable parts inside.
•
Inspection and repair should only be performed by an authorised agent.
Under no circumstances should you attempt to service or repair the S8
Series II yourself.
Frequently Asked Questions
How will it feel when I am breathing with the S8 Series II?
When you first use your S8 Series II device, you may feel uncomfortable breathing
against the airflow. This is normal. You will continue to breathe normally while you
sleep. The EPR setting may also improve comfort. Take time to adjust to this new
sensation.
What do I do when I want to get up in the night?
If you need to get up during the night, remove your mask and stop therapy. Always
remember to restart therapy and put your mask on when you return to bed.
What do I do if I feel air leaking out of the mask?
The S8 Series II delivers the most effective treatment when the mask is well fitted and
comfortable. Treatment can be affected by leaks, so it is important to eliminate any
leaks that may arise. For example, try repositioning the mask and adjusting the straps.
If you are using a nasal mask, try to keep your mouth closed during treatment. Air leaks
from your mouth can decrease the effectiveness of your treatment. If mouth leaks are
a problem, a full face mask or chin strap may help. Contact your clinician or equipment
supplier for further details.
If you are using a full face mask and you have problems trying to get a comfortable
mask fit, contact your clinician or equipment supplier. You may benefit from a different
size or style of mask.
Anything special I should do before putting the mask on?
Before wearing your mask, wash your face to remove excess facial oils. This will allow
a better fit and prolong the life of the mask cushion.
Do not use moisturiser when wearing a mask.
My mouth feels dry during treatment—what can I do?
You may experience dryness of the nose, mouth, and/or throat during the course of
treatment, especially during winter. In many cases, a humidifier may resolve this
discomfort. Contact your clinician for advice.
My nose is irritated during treatment—what can I do?
You may experience sneezing and/or a runny or blocked nose during the first few
weeks of treatment. In many cases, nasal irritation can be resolved with a humidifier.
Consult your clinician or equipment supplier for advice.
Can I travel with the S8 Series II?
Your S8 Series II has an internal power supply that enables it to operate in other
countries. It will operate on power supplies of 100–240V and 50/60Hz. No special
adjustment is necessary, but you will require an approved power cord for the region in
which you are using the device.
Your S8 Series II device automatically adjusts to changes in altitude up to 2,591 m.
Frequently Asked Questions
11
Please consult the medical services department of your carrier if you intend to use your
S8 Series II on an aircraft. The S8 Series II complies with US FCC Part 15, Class B
requirements.
Note: Do not use your S8 Series II while the aircraft is taking off or landing.
Can I use my S8 Series II if mains (AC) power is not available?
A DC-12 converter is available to connect the S8 Series II to a 12V or 24V DC power
source. Contact your clinician for details.
Troubleshooting
If there is a problem, try the following suggestions. If the problem cannot be solved,
contact your equipment supplier or ResMed. Do not attempt to open the device.
Problem/Possible Cause
No display
Solution
Power is not connected.
Ensure the power cable is connected and the power
switch (if available) is on.
Insufficient air delivered from S8 Series II device
Ramp or settling time is in use.
Wait for air pressure to build up or change ramp or
settling time.
Air filter is dirty.
Replace air filter.
Air tubing is kinked or punctured.
Air tubing not connected properly.
Straighten or replace tubing.
Check air tubing.
Mask and headgear not positioned
correctly.
Adjust position of mask and headgear.
Cap(s) missing from access port on
mask.
Replace cap(s).
Pressure required for treatment may See your clinician to adjust the pressure.
have changed.
Device does not start when you breathe into the mask although your clinician
has enabled SmartStart
Power cord not connected properly. Connect power cord firmly at both ends.
Power outlet may be faulty.
Try another power outlet.
Leak Alert has been enabled by your Contact your clinician.
clinician; SmartStart automatically
disabled.
Use of a ResMed Full Face mask.
SmartStart does not work with a full-face mask as the
anti-asphyxia valve will not allow sufficiently high
pressure on exhalation.
Breath not deep enough to trigger
SmartStart.
Take a deep breath in and out through the mask.
12
Problem/Possible Cause
Solution
Excessive leak.
Adjust position of mask and headgear.
Replace caps if missing from ports on mask.
Air tubing may not be connected properly. Connect
firmly at both ends.
Air tubing may be kinked or punctured. Straighten or
replace.
Displays error message: SYSTEM ERRxxxx Call Service!or Exxxx(where
xxxx defines an error)
Component failure.
Record error number and call service.
Displays error message: Check tube!! Key if done
Air tubing is loose or blocked.
Check that the air tubing is connected securely to your
mask and the air outlet to the front of the S8 Series II.
When you have checked the air tubing, press the Start/
Stop key to restart the device. If this does not clear the
message, disconnect the power cord and then
reconnect it to restart the device.
The following message is displayed on the LCD after you try to update settings
or copy data to the Data Card: Card Error Remove Card
Data Card is not inserted correctly.
Check that the Data Card is inserted into the Data Card
module with the arrow facing up, while the S8 Series II
is switched on and not delivering therapy (standby
mode).
The Data Card is only partly
inserted.
Ensure that the Data Card is inserted into the Data Card
slot as far as it will go.
You may have removed the Data
Reinsert the Data Card and wait for the Settings
Card before settings were copied to Success Remove Cardmessage to appear on the
the S8 II.
LCD.
The card is not a ResScan Data
Card.
Only use a ResScan Data Card.
The following message is displayed on the LCD after you try to update settings
or copy data to the Data Card: Settings Error Remove Card
There is a data error on the Data
Card.
Contact your clinician immediately.
The following message is NOT displayed on the LCD after you try to update the
settings using the Data Card: Settings Success Remove Card
The settings were not updated.
Contact your clinician immediately.
Troubleshooting
13
Problem/Possible Cause
Solution
The following message is displayed on the LCD after you try to update settings
or copy data to the Data Card: Settings Invalid Remove Card
The identification details on the
Data Card do not match the
Contact your clinician immediately.
identification details on your device.
Technical Specifications
.
Operating pressure range
Dimensions (H x W x D)
Weight
4 to 20 cm H O
2
112 mm x 164 mm x 145 mm
1.4 kg
Operating Temperature
Power Supply
+5°C to +36°C
•
Input range for S8 Series II with H4i:100–240V, 50/60Hz; 110V,
400Hz; 2.5A < 140VA (110W) (maximum power consumption).
Instantaneous peak power consumption <340VA.
•
•
Refer to the DC-12 converter instructions for DC ratings. Only
use the ResMed DC-12 converter for DC input.
Typical power consumption at 20 cm H 0 is 39VA or 20.7W.
2
Operating Humidity
10%–95% non-condensing
Storage and Transport
Temperature
-20ºC to +60ºC
Storage and Transport
Humidity
10%–95% non-condensing
Sea level to 2,591 m
Operating Altitude
Electromagnetic
Compatibility
Product complies with all applicable electromagnetic compatibility
requirements (EMC) according to IEC60601-1-2, for residential,
commercial, and light industry environments.
The electromagnetic compatibility tables for these ResMed devices
Service & Support. Click on the PDF file for your device.
Two-layered, powder-bonded, polyester non-woven fiber
Air Filter
Air Tubing
Flexible plastic, 2 m
Air Outlet
The 22 mm conical outlet complies with EN 1281-1
Class II (double insulation), Type CF
Flame retardant engineering thermoplastic
IEC 60601-1 Classifications
Housing Construction
DECLARED DUAL-NUMBER NOISE EMISSION VALUES in accordance with ISO 4871:
Sound Pressure Level
24 dBA with uncertainty of 2 dBA as measured according to
ISO 17510-1: 2002
26 dBA with uncertainty of 2 dBA as measured according to
ISO 17510-1: 2007
Sound Power Level
34 dBA with uncertainty of 2 dBA as measured according to
ISO 17510-1: 2007
Supplemental Oxygen
Recommended maximum supplemental oxygen flow: 4 L/min
The manufacturer reserves the right to change these specifications without notice.
14
Symbols which appear on the device
Attention, consult accompanying documents;
Follow instructions for use;
Drip proof;
Type CF equipment; Dangerous voltage;
Class II equipment; Start/Stop;
Manufacturer;
Environmental information WEEE 2002/96/EC is a European Directive
that requires the proper disposal of electrical and electronic equipment. This device should be
disposed of separately, not as unsorted municipal waste. To dispose of your device, you should
use appropriate collection, reuse and recycling systems available in your region. The use of these
collection, reuse and recycling systems is designed to reduce pressure on natural resources and
prevent hazardous substances from damaging the environment. If you need information on these
disposal systems, please contact your local waste administration. The crossed-bin symbol invites
you to use these disposal systems. If you require information on collection and disposal of your
environment.
General Warnings and Cautions
WARNINGS
!
•
Read the entire guide before using the S8 Series II.
•
Advice contained in this guide should not supersede instructions given by the
prescribing physician.
•
•
A patient should not connect a device to the data communication port unless
instructed to do so by their health care provider or physician. Only ResMed
products are designed to be connected to the data communication port.
Connecting other devices could result in injury, or damage to the S8 Series II
device.
The S8 Series II should be used with masks (and connectors)* recommended
by ResMed, or by a physician or respiratory therapist. A mask should not be
used unless the S8 Series II device is turned on and operating properly. The
vent hole or holes associated with the mask should never be blocked.
Explanation: The S8 Series II is intended to be used with special masks (or
*
connectors) which have vent holes to allow continuous flow of air out of the
mask. When the device is turned on and functioning properly, new air from
the device flushes the exhaled air out through the mask vent holes. However,
when the device is not operating, insufficient fresh air will be provided
through the mask, and the exhaled air may be rebreathed. Rebreathing of
exhaled air for longer than several minutes can, in some circumstances, lead
to suffocation. This applies to most models of PAP devices.
•
•
In the event of power failure or machine malfunction, remove the mask.
The S8 Series II can be set to deliver pressures up to 20 cm H O. In the
2
unlikely event of certain fault conditions, pressures up to 30 cm H O are
2
possible.
*
Ports may be incorporated into the mask or in connectors that are near the mask.
General Warnings and Cautions
15
•
If oxygen is used with this device, the oxygen flow must be turned off when
the device is not operating.
If the oxygen has been left on, turn off the device, then wait 30 minutes
before turning on the device again.
Explanation: When the PAP device is not in operation and the oxygen flow is
left on, oxygen delivered into the air delivery tubing may accumulate within
the PAP machine enclosure and create a risk of fire. This applies to most
types of PAP machines.
•
•
•
Oxygen supports combustion. Oxygen should not be used while you are
smoking or in the presence of an open flame.
Always ensure airflow is being generated by the device before the oxygen
supply is turned on.
Always turn the oxygen supply off before stopping the airflow from the
device.
Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen
concentration will vary, depending on where the oxygen is introduced, the
pressure settings, patient breathing pattern, mask selection, and leak rate.
Do not use the S8 Series II if there are obvious external defects or
unexplained changes in performance.
Do not open the S8 Series II case. There are no user serviceable parts inside.
Repairs and internal servicing should only be performed by an authorised
service agent.
•
•
•
Explosion hazard—do not use in the vicinity of flammable anesthetics.
CAUTIONS
•
!
At low pressures, the flow through the exhalation ports of your mask may not
clear all exhaled gas from the tubing. Some rebreathing may occur.
The airflow for breathing produced by this device can be as much as 11ºF
(6ºC) higher than the temperature of the room. Caution should be exercised if
the room temperature is warmer than 90ºF (32ºC).
•
•
When AC mains power (100–240V AC) is not available, always use a ResMed
DC-12 converter. (The DC-12 converter is available as an optional accessory. It
is not supplied with all models.)
Note: The above are general warnings and cautions. Specific warnings,
cautions, and notes appear with the relevant instructions in the manual.
16
Limited Warranty
ResMed warrants that your ResMed product shall be free from defects in
material and workmanship for the period specified below from the date of
purchase by the initial consumer. This warranty is not transferable.
Product
Warranty Period
ResMed humidifiers, ResControl™, ResLink™, ResTraxx™
ResMed flow generators
1 Year
2 Years
90 Days
Accessories, mask systems (including mask frame, cushion,
headgear and tubing). Excludes single-use devices.
Note: Some models are not available in all regions.
If the product fails under conditions of normal use, ResMed will repair or replace,
at its option, the defective product or any of its components. This Limited
Warranty does not cover:
a) any damage caused as a result of improper use, abuse, modification or
alteration of the product;
b) repairs carried out by any service organisation that has not been expressly
authorised by ResMed to perform such repairs;
c) any damage or contamination due to cigarette, pipe, cigar or other smoke;
d) any damage caused by water being spilled on or into a flow generator.
Warranty is void on product sold, or resold, outside the region of original
purchase.
Warranty claims on defective product must be made by the initial consumer at
the point of purchase.
This warranty is in lieu of all other express or implied warranties, including any
implied warranty of merchantability or fitness for a particular purpose. Some
regions or states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
ResMed shall not be responsible for any incidental or consequential damages
claimed to have occurred as a result of the sale, installation or use of any ResMed
product. Some regions or states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights which vary from region to region.
For further information on your warranty rights, contact your local ResMed dealer
or ResMed office.
R001-307/2 05 06
Limited Warranty
17
|