REJ10J1395-0100
H8SX/1663 Group E6000H FP-144L
User System Interface Board
HS1664ECH61H User’s Manual
Renesas Microcomputer Development Environment System
H8SX Family / H8SX/1600 Series
HS1664ECH61HE
Rev.1.00
Revision Date: Jun. 28, 2006
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and
more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corp. product best suited to the customer's application; they do not convey any license
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or
a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-
party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corp. without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or
an authorized Renesas Technology Corp. product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising
from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means,
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data,
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total
system before making a final decision on the applicability of the information and products. Renesas
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or
system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when
considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must
be exported under a license from the Japanese government and cannot be imported into a country
other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products
contained therein.
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this user system interface board.
• KEEP the user's manual handy for future reference.
Do not attempt to use the user system interface board until you fully understand its
mechanism.
User System Interface Board:
Throughout this document, the term "user system interface board" shall be defined as the
following product produced only by Renesas Technology Corp. excluding all subsidiary products.
•
User system interface board (HS1664ECH61H)
The user system or a host computer is not included in this definition.
Purpose of the User System Interface Board:
This user system interface board is for connecting the evaluation chip board and user system.
This user system interface board must only be used for the above purpose.
Improvement Policy:
Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as
Renesas) pursues a policy of continuing improvement in design, performance, functions, and
safety of the user system interface board. Renesas reserves the right to change, wholly or
partially, the specifications, design, user's manual, and other documentation at any time without
notice.
Target User of the User System Interface Board:
This user system interface board should only be used by those who have carefully read and
thoroughly understood the information and restrictions contained in the user's manual. Do not
attempt to use the user system interface board until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the user system interface board.
I
LIMITED WARRANTY
Renesas warrants its user system interface boards to be manufactured
in accordance with published specifications and free from defects in
material and/or workmanship. Renesas will repair or replace any
user system interface boards determined to be defective in material
and/or workmanship. User system interface boards are wearing parts
which Renesas will not repair or replace if damaged and/or worn
through use. The foregoing shall constitute the sole remedy for any
breach of Renesas’ warranty. This warranty extends only to you, the
original Purchaser. It is not transferable to anyone who subsequently
purchases the user system interface board from you. Renesas is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
USER SYSTEM INTERFACE BOARD, THE USE OF ANY USER
SYSTEM INTERFACE BOARD, OR ITS DOCUMENTATION,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS
WARRANTY, THIS USER SYSTEM INTERFACE BOARD IS SOLD
"AS IS ", AND YOU MUST ASSUME ALL RISK FOR THE USE
AND RESULTS OBTAINED FROM THE USER SYSTEM
INTERFACE BOARD.
II
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Renesas shall have no liability or legal responsibility for any problems caused by misuse,
abuse, misapplication, neglect, improper handling, installation, repair or modifications of the user
system interface board without Renesas’ prior written consent or any problems caused by the user
system.
All Rights Reserved:
This user's manual and user system interface board are copyrighted and all rights are reserved
by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any
form, in hard-copy or machine-readable form, by any means available without Renesas’ prior
written consent.
Other Important Things to Keep in Mind:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Renesas.
Figures:
Some figures in this user's manual may show items different from your actual system.
Limited Anticipation of Danger:
Renesas cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the user system interface board are therefore not all
inclusive. Therefore, you must use the user system interface board safely at your own risk.
III
SAFETY PAGE
READ FIRST
• READ this user's manual before using this user system interface board.
• KEEP the user's manual handy for future reference.
Do not attempt to use the user system interface board until you fully understand its
mechanism.
DEFINITION OF SIGNAL WORDS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE emphasizes essential information.
IV
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the E6000H emulator and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Always before connecting any BOARDS, make sure that
pin 1 on both sides are correctly aligned.
V
Preface
The HS1664ECH61H is a user system interface board that connects a user system for the
H8SX/1663, H8SX/1664 FP-144L package to the H8SX/1650 E6000H emulator
(HS1650EPH60H). Emulation of the H8SX/1663 group is only possible when this user system
interface board is connected to the HS1650EPH60H.
i
Contents
Section 1 Configuration.....................................................................................1
Section 2 Connection Procedures......................................................................3
2.1 Connecting the User System Interface Board to the User System.................................... 3
2.1.1 Installing the IC Socket........................................................................................ 4
2.1.2 Soldering the IC Socket....................................................................................... 5
2.1.3 Inserting the IC Socket Connector....................................................................... 5
2.1.4 Fastening the IC Socket Connector...................................................................... 6
2.2 Exchanging the Spacers of the Evaluation Chip Board .................................................... 8
2.3 Connecting the User System Interface Board to the Evaluation Chip Board ................... 9
2.4 Recommended Dimensions for the User System Mounting Pad (Footprint).................... 11
2.5 Dimensions of the Evaluation Chip Board and the User System Interface Board............ 12
2.6 Resulting Dimensions after Connecting the User System Interface Board....................... 13
2.7 Using the Emulator without Connecting User System ..................................................... 14
Section 3 User System Interface Circuits..........................................................16
Section 4 Verifying Operation...........................................................................19
Section 5 Points for Caution..............................................................................21
Section 6 Restrictions........................................................................................23
ii
Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for
the FP-144L package. Please make sure you have all of these components after you have
unpacked the box.
Evaluation chip board
Screws (M2 × 6 mm)
Spacer
Screws (M2 × 10 mm)
(for fastening the board)
Socket cover
User system
interface board
IC socket
User system
Figure 1 User System Interface Board for the H8SX/1663, H8SX/1664 FP-144L Package
1
CAUTION
Use an NQPACK144SD socket (manufactured by
Tokyo Eletech Corporation) as the FP-144L-packaged
IC socket on the user system.
Table 1
HS1664ECH61H Components
No. Component
Quantity Remarks
1
2
User system interface
board
1
1
IC socket
For the FP-144L package (to be mounted on the user
system)
3
4
5
6
7
8
9
Socket cover
1
4
4
For installing an FP-144L-packaged MCU
For fastening the board
Screw (M2 x 10 mm)
Screw (M2 x 6 mm)
For installing an FP-144L-packaged MCU
Spacers (2.6MP x 25 mm) 2
Spacers (2.6MQ x 13 mm) 4
Screwdriver
1
3
1
For tightening screws
Guide pins (φ1 mm)
For determining the IC socket location
User’s manual for HS1664ECH61H (this manual)
10 Documentation
2
Section 2 Connection Procedures
Connecting the User System Interface Board to the User System
WARNING
2.1
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected or removed. Before connecting the two, make
sure that pin 1 on both sides are correctly aligned. Failure to
do so will result in a FIRE HAZARD and will damage the
user system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be LOST.
CAUTION
1. Do not connect a 5-V signal to any pin, including the
USB pins. Incorrect usage will cause damage to the
emulator product, user system interface board, and
user system.
2. To connect the emulator to the user system, ensure that
the SW1 jumper pin is inserted to [USER-ON].
Failure to do so will damage the emulator product, user
system interface board, and user system.
3
To connect the board to the user system, follow the instructions below.
2.1.1 Installing the IC Socket
After checking the location of pin 1 on the IC socket fasten it to the user system before soldering.
CAUTION
After confirming the location of pin 1 on the IC socket,
apply epoxy resin adhesive to the end of the four projections
at the bottom of the IC socket, and fasten it to the user
system.
Use the guide pins provided with the product to determine where to install the IC socket, as shown
in figure 2.
Guide pins
4 projections to apply
epoxy resin adhesive to
IC socket
(NQPACK144SD manufactured
Pin 1
by Tokyo Eletech Corporation)
Bottom view of IC soket
User system
Figure 2 Correctly Placing the IC Socket
4
2.1.2
Soldering the IC Socket
After fastening, solder the IC socket for an FP-144L package to the user system.
CAUTION
Be sure to completely solder the leads so that the solder
gently covers the leads and forms solder fillets. (Use
slightly more solder than with the MCU.)
2.1.3
Inserting the IC Socket Connector
CAUTION
Check the location of pin 1 before inserting.
After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket
connector, align the guide pins on the IC socket connector with the guide holes on the user system
interface board, and insert the IC socket connector into the IC socket (figure 3).
5
2.1.4
Fastening the IC Socket Connector
CAUTION
1. Use the screwdriver provided for tightening screws.
2. The tightening torque must be 0.054 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
Fasten the user system interface board to the IC socket for an FP-144L package on the user system
with the four screws (M2 x 10 mm) provided. Each screw should be tightened a little at a time,
alternating between screws on opposing corners. Take special care, such as manually securing the
IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening
the screws or twisting the components.
6
Screws (M2 × 10 mm)
(for fastening the board)
User system interface board
Pin 1
IC socket
(NQPACK144SD
manufactured by
Tokyo Eletech Corporation)
User system
Figure 3 Connecting the User System Interface Board to the User System
7
2.2
Exchanging the Spacers of the Evaluation Chip Board
After connecting the user system interface board to the user system, be careful not to apply load to
the user system.
Exchange the spacers (2.6MP × 10 mm) of the evaluation chip board with the spacers (2.6MP ×
25 mm) provided with the user system interface board and adjust the height.
Evaluation chip board
Spacer
(2.6MP × 25 mm)
Figure 4 Exchanging the Spacers
8
2.3
Connecting the User System Interface Board to the Evaluation Chip
Board
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected or removed. Before connecting the two,
make sure that the pin 1 positions on both sides are
correctly aligned.
2. The user system interface board must be used with the
emulator for which it was designed.
1. Make sure the user system and emulator are turned off.
2. Align the connectors on the user system interface board with those on the evaluation chip
board by matching the numbers on the connectors (figure 5).
3. Adjust the height of the spacers of the evaluation chip board to accommodate the user system.
9
Evaluation chip board
Connector No.
Evaluation
Chip Board
Connector No.
Board
Connector No.
UCN1
UCN2
UCN1
UCN2
User system interface board
Figure 5 Connecting the User System Interface Board to the Evaluation Chip Board
10
2.4
Recommended Dimensions for the User System Mounting Pad
(Footprint)
Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system
with the IC socket for an FP-144L package (NQPACK144SD: manufactured by Tokyo Eletech
Corporation). Note that the dimensions in figure 6 are somewhat different from those of the
mounting pad for the system with the actual MCU.
23.00 0.15
11.50
2.00 0.10
0.50
0.25 (max.)
Unit: mm
Tolerance:
0.10 mm
Figure 6 Recommended Dimensions for the Mounting Pad
11
2.5
Dimensions of the Evaluation Chip Board and the User System
Interface Board
The dimensions of the evaluation chip board and the user system interface board are shown in
figure 7.
140.0
Evaluation chip board
118.5
102.5
16.0
78.5
User system interface board
Unit: mm
Tolerance: 0.5 mm
Figure 7 Dimensions of the Evaluation Chip Board and the User System Interface Board
12
2.6
Resulting Dimensions after Connecting the User System Interface
Board
The dimensions of the assembly after the user system interface board has been connected to the
user system are shown in figure 8.
Evaluation chip board
56.5
IC socket
(NQPACK144SD
manufactured by
Tokyo Eletech Corporation)
Spacer (φ5.8)
User system
56.5
Unit: mm
Tolerance: 1.0 mm
Figure 8 Dimensions of the Assembly after Connection of the User System Interface Board
13
2.7
Using the Emulator without Connecting User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected or removed. Before connecting the two, make
sure that pin 1 on both sides are correctly aligned. Failure to
do so will result in a FIRE HAZARD and will damage the
user system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be LOST.
CAUTION
When this emulator is used without connecting to the
user system, ensure that the SW1 jumper pin is inserted to
[USER-OFF]. Failure to do so will damage the emulator
product, user system interface cable, and user system.
Attach the provided spacers (2.6MQ x 13 mm) to four positions on the user system interface board
not to apply loads to the connector (CN1) on the board (figure 10).
14
USER ON
SW1
P1
USER OFF
Figure 9 SW1 Jumper Socket
Spacer
(2.6MQ x 13 mm)
Figure 10 Attaching Spacers
15
Section 3 User System Interface Circuits
The following user interface circuits are required for the emulator when the user system interface
board is in use.
User system
Vcc
Sub-MCU
Monitoring
circuit
EPM7128
47 kΩ
MD3
Vcc
MD control
circuit
Monitoring
circuit
LPT16244
47 kΩ
MD_CLK
MD_CLK
PM0-PM4
VBUS
PM0-PM4
VBUS
EPM7128
1 kΩ
DrVcc
USD-
DrVcc
Power-supply
circuit
USD-
USD+
DrVss
USD+
DrVss
Figure 11 User System Interface Circuit (1)
Note: The power-supply circuit shown above is turned on/off by the setting of the SW1 jumper
pin on HS1664ECH61H. Ensure that the jumper pin is inserted to [USER-ON] on
HS1664ECH61H when connecting the emulator (with HS1664ECH61H attached) to the
user system or supplying power to DrVCC. Otherwise the emulator product, user system
interface board, and user system will be damaged.
16
MCU
User system
SN74CB3Q3306A
P23
P27
P23
P27
SN74CB3Q3306A
Figure 12 User System Interface Circuit (2)
MCU
User system
P14
SN74CB3Q3306A
P14
Sub-MCU
SN74CB3Q3306A
TXD
Figure 13 User System Interface Circuit (3)
17
MCU
User system
_RES
Vcc
EPM7128
UHC14
VHC244
47 kΩ
_RES
EPM7128
Figure 14 User System Interface Circuit (4)
18
Section 4 Verifying Operation
1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H
Emulator User's Manual (HS1650EPH60HE).
2. Verify the user system interface cable connections by checking the pin states with the
EXMONITOR_DISPLAY command (emulator command) and checking the bus states with
the MEMORY_FILL command (emulator command). If an error is detected, recheck the
soldered IC socket and the location of pin 1.
3. The emulator connected to this user system interface board supports three kinds of clock
sources as the MCU clock. For details, refer to the H8SX/1650 E6000H Emulator User's
Manual (HS1650EPH60HE).
⎯ To use the emulator internal clock
Select the clock in the emulator by the CLOCK command (emulator command).
⎯ To use the external clock on the user system
Supply the external clock from the user system to the emulator by inputting the signal to
the EXTAL pin (pin 98) on the user system interface board or connecting a crystal
oscillator to the XTAL (pin 97) and EXTAL pins. For details, refer to the H8SX/1650
Hardware Manual.
Figure 15 shows the clock oscillator on the user system interface board.
HCU04
1 MΩ
HCU04 HCU04
HCU04
HCU04
0 Ω
To E6000H
emulator
HCU04
270 Ω
EXTAL XTAL
System clock
Figure 15 Clock Oscillator
19
⎯ To use the crystal oscillator mounted on the evaluation chip board
Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip
board.
Enlarged
view
Crystal
oscillator
X1
X2
Crystal oscillator terminals
Evaluation chip
board
Figure 16 Installing the Clock Oscillator
20
Section 5 Points for Caution
1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both
sides are correctly aligned.
2. Do not apply excessive force to the user system interface board while it is connected to the
user system.
3. The dimensions of the recommended mounting pad for the IC socket for this user system
interface board are different from those of the pad for the MCU.
4. This user system interface board is specifically designed for the HS1650EPH60H emulator.
Do not use this board with any other emulator.
5. When power is not being supplied to the Vcc pin on the user system interface board, the
emulator displays ** VCC DOWN. In this situation, the emulator will not operate correctly.
6. The P1 short connector is used for testing. Do not remove the inserted jumper pin.
Do not remove the
jumper pin.
1
3
P1
USER ON
SW1
USER OFF
Figure 17 Jumper Socket
7. Do not connect this user system interface board to the user system for the H8SX/1650 group.
21
8. When you use the emulator without connecting it to the user system, ensure that the SW1
jumper pin is inserted to [USER-OFF]. While no pin or SW1 jumper pin is inserted to
[USER-OFF], the emulator supplies 3.3-V power to DrVCC, which is the power supply
exclusively used for USB.
9. To connect the emulator to the user system, ensure that the SW1 jumper pin is inserted to
[USER-ON]. While SW1 jumper pin is inserted to [USER-ON], the emulator does not supply
power to DrVCC, which is the power supply exclusively used for USB. Thus the power must
be supplied from the user system instead.
10. Do not connect a 5-V signal to any pin, including the USB pins. Incorrect usage will cause
damage to the emulator product, user system interface board, and user system.
22
Section 6 Restrictions
There are the following restrictions on emulation of the H8SX/1663 group when the user system
interface board is connected to the emulator.
1. The USB clock frequency is fixed to 48 MHz regardless of the EXTAL input.
2. P14 cannot be used as a port if the serial output function has already been selected. The port
pin state cannot be read from the port register.
3. The user system interface board does not support subclock operation. Thus the following
function and register cannot be used:
- 32k timer
- Subclock control register (SUBCKCR) of the clock pulse generator
- Interrupt priority register D (IPRD2 to IPRD0)
4. Exception processing of sleep instructions is not supported. Even if the SLPIE bit of the
standby control register (SBYCR) is set to 1, the emulator enters the power-down mode and no
exception processing of sleep instructions occurs.
23
H8SX/1663 Group E6000H FP-144L
User System Interface Board
HS1664ECH61H User's Manual
Publication Date: Rev.1.00, June 28, 2006
Published by:
Sales Strategic Planning Div.
Renesas Technology Corp.
Customer Support Department
Global Strategic Communication Div.
Renesas Solutions Corp.
Edited by:
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
RENESAS SALES OFFICES
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
Colophon 6.0
H8SX/1663 Group E6000H FP-144L
User System Interface Board
HS1664ECH61H User’s Manual
|