Regalo Pet Fence 1164 User Guide

12/10/2013_EV  
Easy Step Gate  
MODEL NO: 1164 & 1166H  
Owner’s Manual  
READ ALL INSTRUCTIONS BEFORE ASSEMBLY  
AND USE OF GATE.  
KEEP INSTRUCTIONS FOR FUTURE USE.  
...........................................................................  
Regalo International, LLC.  
3200 Corporate Center Drive, Suite 100  
Burnsville, MN 55306-9803, USA  
Toll Free: 866-272-5274  
Made in China  
 
Check to make sure you have all of the parts shown:  
B.  
C.  
A.*  
D.  
A. Gate Frame  
B. 4 Wall Cups  
C. 4 Screws (requires a Phillips/crosshead screwdriver)  
D. 4 Threaded Spindle Rods  
1
 
Extensions List  
NOTE  
12  
8
6
4
Item NO.  
MAX Size  
29--52 inches  
29--40 inches  
1164  
1166H  
NOTE: When installing any gate at its maximum width use Wall  
Mounting Cups to ensure stability and safety.  
2
 
Assembling andInstalling Your Gate  
**Note: IMPORTANT!! You will notice a slight gap between the gate door latch and the  
frame. THIS IS NOT A DEFECT. Your gate is a pressure mounted gate and this gap will  
disappear once you tighten your gate in its opening.  
Step 1.  
Locate the 4 threaded spindle rods. Rotate the adjustment wheels along the threading,  
eliminating the gap between the adjustment wheel and the rubber foot.  
Threaded Spindle Rod  
Diagram A  
Adjustment Wheel  
Rubber Foot  
Step 2.  
Insert the 4 threaded spindle rods into the holes at each of the 4 corners of the gate as  
shown in the Diagram B  
Diagram B  
3
 
Step 3.  
Position the gate so that it is level and centered within your doorway or opening.  
Rotate the adjustment wheels on the threaded spindle rods in the opposite direction  
as in Step 1, expanding the gap between the rubber foot and the adjustment wheel.  
Expand each of the 4 Threaded Spindle Rods until they make contact with the  
doorway or opening. Do not fully tighten the Threaded Spindle Rods yet.  
Diagram C1  
Diagram C2  
It may be necessary to hold the Threaded Spindle Rods or Rubber  
Feet while rotating the Adjustment Wheels to ensure the entire  
unit does not rotate.  
HINT:  
4
 
Step4.  
When you are satisfied with the general placement of your gate, fully tighten  
the Threaded Spindle Rods attached to the lower corners of the gate by  
further rotating the Adjustment Wheels.  
Continue by tightening the upper Threaded Spindle Rods. As you tighten the  
upper Threaded Spindle Rods, you will notice the gap between the Door  
Frame and the Easy Open Latch begin to narrow.  
In order for the gate to function properly, stop tightening the upper  
Threaded Spindle Rods just before the inner wall of the Locking Latch and  
the Gate Frame touch.  
Easy Open Latch  
Locking Latch  
Gate Frame  
Diagram D  
There should be equal spacing among each of the 4 Threaded  
Spindle Rods. Make the appropriate adjustment to ensure you  
have installed your gate safely.  
NOTE:  
5
 
Positioning and Attaching the Wall Cups  
Your gate is a pressure mounted gate. Therefore, it is not necessary to use the screw  
attached Wall Cups in your door opening if you choose not to. However, IF YOUARE  
USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS. Using the  
Wall Cups will affix your gate more firmly in the doorway or opening.  
Step1.  
After you have mounted your gate, and you are satisfied with its positioning, use a  
pencil or other marking tool to draw a circle on the surface of your doorway or  
opening around the perimeter of the 4 rubber feet.  
Diagram E  
Step2.  
Next, completely remove the gate from the opening by loosening each of the 4  
Threaded Spindle Rods and de-pressurizing the gate.  
6
 
Step3.  
With the gate fully removed, you can now use the circles you marked during Step 1  
as guides for screwing in your 4 Wall Cups.  
Center each of the Wall Cups within the guide circles and use the provided  
self-tapping screws to fasten them in place via the hole through the center of each  
Wall Cup.  
Diagram F  
Step4.  
Reinstall your gate in the doorway or opening according to the instructions, using  
the newly installed Wall Cups as anchoring points for the 4 Threaded Spindle Rods  
Diagram G  
7
 
Operating the Door Latch  
Step1.  
Pull the Spring Lock away from the Easy Open Latch while simultaneously  
lifting the Lock Lever upwards. This will release the Locking Latch from the  
Gate Frame and allow the door to push or pull open.  
Spring Lock  
Lock Lever  
Diagram H  
Step2.  
To lock the door shut, close the door completely, then push down on the  
Lock Lever to re-engage the Spring Lock  
If your Easy Open Latch is not properly engaging with the  
receiving component, ensure that your gate is level, mounted  
HINT:  
properly, and that you have not over-tightened the threaded  
Spindle Rods.  
8
 
Adding a Gate Extension  
Step 1. Assemble the gate per the gate instructions.  
Step 2. Choose the side of the gate to be extended and remove the top  
and bottom Threaded Spindle Rods.  
Step 3. Assemble the gate and extension as illustrated.  
Step 4. Reposition the gate and fit in accordance with the gate fitting  
instructions.  
Removing Your Gate From The Wall  
To remove your gate from the wall, rotate the Adjustment Wheels on  
each of the 4 Threaded Spindle Rods to depressurize the gate from its  
doorway or opening. Then, gently pull or push the gate free from its  
doorway or opening.  
9
 
Care And Maintenance  
Periodically check the gate for signs of damage, wear, or missing  
components.  
Do not use if any part is missing, worn or damaged.  
Check the gate regularly to ensure all the hardware and mountings are  
tightened.  
Do not use abrasive cleaners or bleach.  
Clean by sponging with warm water and a mild detergent.  
90 Days Limited Warranty:  
If, during the first 90 days after consumer purchase of the item, under  
reasonable and non-commercial use and conditions of maintenance, it  
fails while owned by the original purchaser because of the quality of  
materials or workmanship of finish and assembly, Regalo International  
LLC will replace or repair it at Regalo’s option. PROOF OF PURCHASE  
REQUIRED.  
10  
 
Replacement Parts Available  
In the event of any damage or breakage, the following replacement parts  
are available for order by contacting Regalo Customer Service.  
Wall Cups  
(Gray = #14015)  
(Black = #11015)  
1” Wall Mount Screws  
Threaded Spindle Rods  
with Adjustment Wheel  
(#10001)  
(Gray = #14016)  
(Black = #11016)  
Pet Door Pull Knob  
(#13038)  
Bottom Plug Insert  
(Gray = #14019)  
(Black = #11019)  
Top Plug Insert  
(Gray = #14020)  
(Black = #11020)  
Easy Open Latch  
(Gray = #14037)  
(Black = #11037)  
(White = #13037)  
Contact Regalo for questions and replacement parts.  
For questions about the use of your gate, call our customer care line 866-272-5274.  
Regalo International, LLC.  
3200 Corporate Center Drive, Suite 100  
Burnsville, MN 55306-9803, USA  
Made in China  
 
Regalo International, LLC.  
3200 Corporate Center Drive, Suite 100  
Burnsville, MN 55306-9803, USA  
Toll Free: 866-272-5274  
Made in China  
12/10/2013_EV  
 

RCA CD Player LAD885 User Guide
Realistic Marine Radio HTX 100 User Guide
Ricoh Printer L4130 User Guide
Roland Musical Instrument Amplifier AC 60 User Guide
Roland Music Mixer S 0816 User Guide
RTS Network Card SSA 324 User Guide
Samsung Computer Drive BG68 01622A User Guide
Samsung Digital Camera EC EX2FZZBPBUS User Guide
Sanus Systems TV Video Accessories AFV48B User Guide
Sears Planer 91738614 User Guide