FOR THE MOST IMPORTANT PEOPLE
IN THE WORLD
TM
TRAVEL DINER
PORTABLE HOOK–ON HIGH CHAIR
Models: 2772
Owner’s Manual
06/21/2013_DC
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY
AND USE OF CHAIR.
• KEEP INSTRUCTIONS FOR FUTURE USE.
...........................................................................
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE
OF CHAIR. KEEP INSTRUCTIONS FOR FUTURE USE.
ASSEMBLING YOUR TRAVEL DINER CHAIR
1.Remove the black plastic protective caps from the ends
of the backrest bar. These black plastic caps are for packing
purpose only and should be discarded.
If the backrest bar (U – shaped) is not fitted, slide the arm
through the sleeve at the back of the seat cover until the
pins on the tube are exposed on either side of the sleeve.
2.Assess the position of each arm. For the correct position
of each arm you must have:
a.Round rubber stopper positioned at front.
b.Round lock release button on clamp must face the
outside of the chair.
c.Rubber paddle – grip positioned at top.
2
3.Slide each paddle-grip through the cover of each sleeve
located on the side of the seat. Insert from the back of the
sleeve and push the arm through.
*Remember, the lock release button on the clamp must
facing to the outside.
4.Remove the black plastic protective caps from the
openings of both arms and discrad them. The caps are only
for packaging purposes. Next, attach both arms onto the
backrest bar, pushing the spring pin in, as you slide the
arms over the backrest bar.
3
TIPS FOR INSTALLING YOUR TRAVEL DINER CHAIR
Step 1.
Make sure the two locks (H) are angled forward (see the
position in Diagram (1). Press in the lock release button(D)
to do this. Fit onto a table or suitable flat surface as shown
in Diagram (1)
Diagram 1
(H)
(D)
Step 2.
Install the Travel Diner on the table top as shown in the
Diagram 2a. Then, push down on the back of the Travel
Diner as indicated by the arrow in Diagram 2b, until the
seat is almost level with the table top . Next, pivot the
locks back until they automatically lock in the vertical
position as shown in Diagram 2c.
Diagram 2a
Diagram 2c
Diagram 2b
4
Step 3.
To lock your Travel Diner onto the table, continue pushing
down on the back of the Travel Diner and at the same time
turn the plastic locking knobs ( J ) clockwise as indicated by
the arrow in this diagram 3. Continue turning the locking
knobs until they are tight against the bottom of the table
surface. Your Travel Diner should now be securely locked to
the table top. If properly locked to the table top, you should
not be able to pull your Travel Diner off the table, even
when pulling with a reasonable amount of force.
(J)
Diagram 3
HARNESS INSTRUCTIONS
To secure your child in the harness, push buckle tongues (A)
into buckle housing (B) and adjust with waist strap adjuster
so that the waist strap is firmly secured around child.
Attach shoulder straps in position on buckle tongues (A) and
adjust so that they are secure, yet comfortable on child.
Adjuster
Adjuster
Strap
Clips
Waist Strap
Adjuster
Waist Strap
Adjuster
Buckle Housing (B)
Buckle
Tongue (A)
Buckle
Tongue (A)
5
CLOSING THE TRAVEL DINER CHAIR
Before attempting to close the Diner Chair, remove your
child. Loosen the table locks on the Diner Chair arms.
Press in the lock release buttons and angle the table locks
forward. Remove the Diner Chair from the table. Fold the
Diner Chair seat arms inward to store the Diner Chair.
CARE AND MAINTENANCE
Periodically check the Diner Chair for sign of damage, wear or
for missing components. Do not use if any part is missing,
worn of damaged. Always dry metal parts to avoid the
formation of rust. Regularly check the securing screws to
ensure that they are securely tightened and tighten when
necessary.
FABRIC CARE
Always check the strength of the fabric and the strength of
the stitching each time the fabric is washed.
90 Days Limited Warranty:
If, during the first 90 days after consumer purchase of this item,
under reasonable and non-commerical use and conditions of
maintenance, it fails while owned by the original purchaser because
of the quality of materials or workmanship of finish and assembly,
Regalo International LLC will replace or repair it at Regalo’s option,
proof of purchase required.
If you have any questions or comments contact:
Regalo, International
Toll free: 866-272-5274
Made in China.
6
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
06/21/2013_DC
|