A™5 Lux Scooter
Owner’s Manual
Read and understand this entire manual before
allowing child to use this product!
For assistance contact Razor. DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Version: 1_01_10
BEFORE yOU BEgIN
Remove contents from box. Remove the foam separators that protect the components from damage during shipping.
Inspect the contents of the box for scratches in the paint, dents that may have occurred during shipping. Because your
scooter was assembled and packed at the factory, there should not be any problems, even if the box has a few
scars or dents.
WARNINg: DO
NOT USE NON-RAZOR
PRODUCTS WITH YOUR
SCOOTER.
Razor scooters have been built to
certain Razor design specifications.
The original equipment supplied at
the time of sale was selected on
the basis of its compatibility with
the frame, fork and all other parts.
Certain aftermarket products may
or may not be compatible.
Handlebar
Consult your retailer or visit
T-tube
or replacing any component with a
non-factory specified product.
Steering tube quick-release lever
Extension tube/steering column
Collar clamp
Joint lever/pivoting mechanism
Rear Fender/brake
Front fork
Deck
Steering column adjusting screw
q Required Tools
We recommend the use of mechanic’s grade tools.
3mm & 5mm
hexagonal key wrench
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
2
SET Up AND USAgE INSTRUCTIONS
Unfolding the scooter for first time use.
WARNINg: Failure to
properly engage the spring-loaded
buttons may cause the handlebars
to dislodge while riding and may
cause you to lose control and
fall. When correctly engaged the
handlebars will not rotate nor will
they move sideways. Note that
when properly engaged, the spring-
loaded buttons are clearly visible in
the holes on the T-tube.
1 Insert and secure the left and
right handlebars by pressing the
spring-loaded buttons and
2 Make certain the spring-loaded
button engages the hole in the
T-bar for each handlebar.
3 To release the folding
mechanism, hold the T-tube with
one hand between the collar clamp
and the quick-release lever and
place your foot on the deck plate.
With the other hand, pull the
joint lever up to release the steer-
ing column from the locked position
and allow you to pivot it to the
upright position.
inserting them into the T-tube.
WARNINg: Keep
your fingers clear of the pivoting
mechanism when folding or
unfolding the scooter. Make sure
others are standing clear.
4 The Joint lever is spring-loaded
and will automatically lock in the
upright position when fully upright.
5 To adjust the height of the
6 The tension of the quick-release
lever can be adjusted by tightening
or loosening the allen bolt. Be care-
ful not to over-tighten. You should
always be able to open and close
the quick-release lever by hand and
the T-tube should slide freely with
the quick-release open.
handlebars, unlock the extension
tube by pulling outward on the
quick-release lever and pushing the
button located on the extension
tube. Slide the T-tube to the desired
position and secure by pushing
inward on the quick release lever.
CHECk BEFORE RIDINg
Collar Clamp
WARNINg: Failure to
properly engage the quick-release
lever may cause the T-tube to side
up or down while riding which
may cause you to lose control
and fall. With the quick-release
properly adjusted and engaged,
the handlebars will not move up or
down.
Using the 5mm Allen wrench, check that the collar clamp bolt is tightened securely. This item is tightened and quality
inspected at the factory, but there is a slight chance that the effects of
shipping or handling may have caused this bolt to loosen.
3
CHECk BEFORE RIDINg
Baseboard/Steering Column Adjusting Screw(s).
WARNINg: Keep
your fingers clear of the pivoting
mechanism when folding or
unfolding the scooter.
With the scooter in the upright and locked position, using a 3mm Allen wrench, adjust the set screw at the baseboard
until there is no free-play between the baseboard and the steering column. Be careful not to over-tighten this screw as
it only needs to be snug against the steering column. Verify the adjustment by releasing the steering column from the
locked position and folding the scooter. The locking lever should not bind and the folding movement should be smooth.
The spring-loaded mechanism should automatically lock and be fully seated in the upright position.
Wheels and Bearings
WARNINg: Wheelies
and other stunt-type riding reduces
your ability maneuver and control
your scooter. Take the necessary
precautions, such as wearing
appropriate protective gear and
practice in a area safe for stunt
riding and free from obstructions.
Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless, it
is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper
tightness, and bearings for side-to-side play and loose parts. When a wheel or wheel bearing develops play, this is an
indication of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn
wheels and bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other
than genuine Razor wheels may not be compatible with your Razor scooter. The use of anything other than genuine
Razor replacement parts may affect your safety and will void your warranty.
Cleaning your Scooter
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
How to Ride
Place one foot on the baseboard, push forward with the other foot. Steer. For enhanced cornering, lean slightly into the
direction of the turn. For controlled stops, apply the brake by stepping on the rear fender/brake. Razor recommends that
you practice applying the brake at various speeds and in an open area free from obstructions before riding your Razor
around others.
4
SAFETy REMINDERS
pRE-RIDE CHECkLIST
Loose parts
Be Careful!
Check and secure all fasteners before every ride. Make sure the
steering tube clamps, steering tube extension quick release,
and handlebars spring buttons are locked properly in place
before riding.
You will see people on TV and maybe even people you know doing
tricks and stunts. These are people who have been practicing on
scooters for a very long time. Don’t try something until you are
ready. Avoid steep inclines and don’t ride too fast — you can lose
control and fall. Skateboard parks are not designed for scooters.
Never ride in traffic or on the street and watch your surroundings
for pedestrians, bikers, boarders and skaters.
q
q
Replacement parts
For a complete selection of parts, visit our website at
q
q
Maintain a hold on the handlebars at all times.
Safety gear
Always wear proper protective equipment such as an approved
safety helmet. Elbow pads and kneepads are recommended.
Always wear shoes (lace-up shoes with rubber soles), never ride
barefooted or in sandals, and keep shoelaces tied and out of the
way of the wheels.
DO NOT RETURN TO STORE
Failure to follow these instructions may damage
your scooter and void your warranty.
WARRANTy
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects
for a period of 6 months from date of purchase. This Limited Warranty does
not cover normal wear and tear, tires, tubes or cables, or any damage, failure
or loss caused by improper assembly, maintenance, or storage.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation
• modified in any way
• rented
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
Printed in China for:
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
Copyright © 2003-2010 Razor USA, LLC. All rights reserved. RAZOR and the Razor Logo
Design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries.
01/2010
5
|