Raritan Computer Camping Equipment MCIP116 User Guide

MCIP18, MCIP116  
MCIP Configuration  
MCIP18  
MCIP116  
desired computer's Key Number, as listed in  
the left column of the OSUI. To select a dif-  
ferent computer, re-activate the OSUI ([Left  
CTRL] three times rapidly).  
between Global and Individual.  
3. Press Tab or Shift+Tab to move for-  
ward or back to the desired field and make  
your changes as follows:  
MCIP Installation  
c. To turn AutoSkip ON/OFF (default  
is OFF): Move to Skip and press the  
up/down arrow keys to toggle. With  
AutoSkip ON, only active channels can be  
selected.  
a. To turn Security ON/OFF (default  
is OFF): Press the up/down arrow keys to  
toggle.  
IV. MCIP Software  
Configuration  
1. Activate the OSUI by pressing the Hot  
Key (default: [Left CTRL]) three times rapid-  
ly. When the OSUI appears, press F4 to  
access the Configuration Menu.  
d. To change the ID Display time  
interval (default is 3 seconds): Move to ID  
Display and type a number from 01 to 99, or  
press the up/down arrow keys to specify the  
interval (in seconds) you want the Channel  
ID and Name to display when each comput-  
b. To change Security activation  
delay time (default is 15 minutes). Move to  
the Time Out field, then type a number from  
01 to 99, or use the up/down arrow keys to  
specify a time interval. If the system will  
remains inactive (no keyboard or mouse  
3
4
er is selected. Type 99 if you want the operation) for this time interval, the next  
Channel ID and Name to display continu-  
ously.  
user is required to enter a password to  
access the MasterConsole IP.  
e. Green mode is disabled.  
c. To change the Administration  
Password: Move to Change Passwords,  
where Admin will be highlighted. Press the  
Enter key and type a new password (up to  
eight alphanumeric characters, no spaces).  
Press Enter. Confirm the password by  
retyping it. Press Enter.  
2
f.  
Previous channel key function is  
disabled.  
3. To exit the Configuration Menu, press  
a Function key on your keyboard to access  
a different menu, as displayed along the  
bottom of the menu screen. Press Esc to  
exit the OSUI and return to normal comput-  
er operation. Any changes made in the  
Configuration Menu are automatically  
saved.  
Congratulations on your purchase of  
Raritan’s MasterConsole IP.  
Your MasterConsole IP (MCIP) unit is  
designed for quick, easy installation and  
operation:  
II. Installation  
III. On-Screen User Interface  
(OSUI) Operation  
d. To change a User Password,  
press the Tab key to highlight the desired  
User# field. Press Enter. Type a new pass-  
word (up to eight alphanumeric characters,  
no spaces). Press Enter. Confirm the pass-  
word by typing it again. Press Enter.  
Repeat this process for the remaining four  
Users, pressing the Tab key to move from  
one User field to the next. You can specify  
up to five User Passwords.  
1. Power OFF all computers to be con-  
nected to the MCIP unit.  
After connecting your computers to your  
MCIP, explore MCIP operation and view fac-  
tory default names and parameters. To acti-  
vate the On-Screen User Interface (OSUI),  
press the left CTRL key on your keyboard  
three times rapidly. The Selection Menu  
appears.  
2. Use the Tab or the Shift + Tab keys to  
move forward or back in the list and high-  
light the desired field. Make your changes  
as follows:  
2. Plug a keyboard, monitor, and mouse  
into the keyboard, monitor, and mouse ports  
on the rear panel of the MCIP.  
1. Set up one-tier MCIP configuration.  
2. Install MCIP and connect computers.  
3. Configure MCIP software.  
V. MCIP Security and  
Passwords  
1. Activate the OSUI by pressing the Hot  
Key (default: [Left CTRL]) three times rapid-  
ly. When it appears, press F5 to access the  
Administration Password prompt.  
3. Power ON MCIP.  
4. Using an MCIP cable (CMCIP20, 40, or  
90), plug the 15-pin connector into one of the  
numbered channels on the MCIP rear panel.  
a. To change Name (default is the  
unit's model number): Move to Name and  
type a name up to seven characters. This  
field is used for identification purposes only.  
4. Assign computer names and set chan-  
nel-specific scan rates for attached comput-  
ers.  
e. To change the type of keyboard,  
press the Tab key to highlight Language  
Mode field. Press the up/down arrow keys  
to select English, German, or French.  
b. To turn AutoScan ON/OFF  
(default is OFF): Move to Scan and press  
the up/down arrow keys to toggle. If you exit  
the OSUI with AutoScan ON, MCIP will scan  
according to the currently set mode  
(Individual/Global) and scan rate.  
5. Plug the cable's other connectors into  
the computer's keyboard, monitor, and  
mouse ports.  
5. Turn ON security and change pass-  
words to restrict access to computers con-  
nected to MCIP.  
2. Type the Administration Password and  
press Enter. The Administration Menu  
appears.  
6. Power ON the connected computer.  
4. To exit the Administration Menu, press  
a Function key on your keyboard to access  
a different menu, as displayed along the  
bottom of the menu screen. Press Esc to  
exit the OSUI and return to normal comput-  
er operation.  
6. Operate MCIP using the On-Screen  
User Interface.  
7. Select the connected computer using  
the OSUI (see next section). Verify that the  
monitor attached to the MCIP unit displays  
the video for the connected computer. Use  
the keyboard and mouse attached to the  
MCIP to verify that they operate the connect-  
ed computer.  
-
To change the Global Scan Rate  
(default is 3 seconds): Move to Set and type  
a number from 01 to 99, or press the  
up/down arrow keys to specify the Scan  
Rate (in seconds) for Global AutoScan.  
I. One-tier Configuration  
For assistance in the North or South America, please con-  
tact the Raritan Technical Support Team by telephone  
(732) 764-8886, by fax (732) 764-8887, or by e-mail  
[email protected] - Ask for Technical Support - Monday  
through Friday, 8:00am to 8:00pm, Eastern.  
Your MasterConsole IP can be configured in  
a one-tier configuration, in which up to 8 (with  
MCIP18) or 16 (with MCIP116) computers  
can be connected to a single MCIP unit.  
-
To change AutoScan mode  
Use the up and down arrow keys on your  
keyboard to highlight a channel (computer)  
on the OSUI and press Enter OR press the  
8. Repeat steps 4 through 7 to connect the  
remaining computers to MCIP.  
(default setting is Global): Move to Mode  
and press the up/down arrow keys to toggle  
 

Quasar Camcorder VM L451 User Guide
Radio Shack Microphone 33 3001 User Guide
Raypak Water Heater 2339B User Guide
RedMax Blower EBZ5000 User Guide
Reliance Water Heaters Water Heater 0002919340 User Guide
Revolabs Microphone QSG TTM User Guide
Roberts Radio Portable Radio Revwal User Guide
Samson Mixer MPL 1640 User Guide
Samsung Tablet SGH I497ZSAATT User Guide
Samsung Work Light series 7500 User Guide